(1) Grade 301 Good ductility, used for molded products. It can also be hardened by mechanical processing. Good weldability. Wear resistance and fatigue strength are better than grade 304 stainless steel, used in products such as springs, steel structures, wheel covers. (2) Grade 302:The corrosion resistance is the same as grade 304, and the strength is better due to the relatively high carbon content. (3) Grade 303:It is easier to cut than grade 304 by adding a small amount of sulfur and phosphorus. (4) Grade 304: It is a stainless steel that is non-magnetic and cannot be changed by heat treatment. The standard composition is 18 % chromium plus 8 % nickel. Used in products such as: corrosion-resistant containers, tableware, furniture, railings, medical equipment, some mobile phone frames. (5) Grade 304L:It has the same characteristics as grade 304, but with low carbon, it is more resistant to corrosion and easy to heat treatment, but has poor mechanical properties. It is suitable for welding and products that are not easy to heat treatment. (6) Grade 304N:With the same characteristics as grade 304, it is a nitrogen-containing stainless steel. Nitrogen is added to increase the strength of the steel. (7) Grade 309:Better temperature resistance than grade 304. (8) Grade 309S:With a large amount of chromium and nickel, it has good heat resistance and oxidation resistance, and is used in products such as heat exchangers, boiler components, and jet engines. (9) Grade 310S:Contains the most chromium and nickel, so it has the best heat resistance and oxidation resistance. It is used in products such as heat exchangers, boiler components, and electrical equipment. (10) Grade 316: After grade 304, the second most widely used steel grade, mainly used in the food industry and surgical equipment, the addition of molybdenum gives it a special structure that is resistant to corrosion. Because of its better resistance to chloride corrosion than grade 304, it is also used as "marine steel". SS316 is usually used in nuclear fuel recovery units. Grade 18/10 stainless steels generally also meet this application level. Especially used in chemical, seaside and other corrosive environments, ship assembly, building materials. (11) Grade 316 L: Low carbon, so it is more resistant to corrosion and easy to heat treatment. It is used in products such as chemical processing equipment, nuclear power generators, and refrigerant storage tanks. (12) Grade 321:Similar to grade 304, except that the risk of corrosion of the material weld is reduced due to the addition of titanium elements, suitable for welding. Used in products such as brewing equipment, steam pipes, aerospace parts. (13) Grade 347 The stabilizing element niobium is added and is mainly used for welded parts used at high temperatures.
We can supply interior, exterior and architectural decoration Stainless Steel Coil. The products are widely applied, such as elevator decoration, wall & ceiling decoration, furniture decoration, advertising nameplate, kitchen equipment and cabinet. Please feel free to contact us to find more details.
Stainless steel raw materials of all grades and sizes, s s coils.
Stainless steel coil , sheet, pipe and tubes.
Example: 304 coil, 1219mm*1.0mm(thickness), 20 tons, 20ft container, FOB. Final price: $3100--$3200,USD
550mm 1mm thickness coils 3 tons/ coils, $1500/tons, $4500/coil. FOB, CIF
Products: Stainless Steel Coils /sheets Size: 0.2-30mm Thickness 8-1500mm Width Length Customized Surface: 2b Finish, No.1 Finish, 4k, 8k. Processing: Hot Rolled, Cold Rolled Packing: Standard Exporting Package. Origin: Posco, Tisco, Bao Steel Etc
Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,.Buying office, oem, components sourcing, value added services
J series of 201 stainless steel | J1, J2, J3, J4, J5 J1: The carbon content is slightly higher than J4, and the copper content is lower than J4. Its processing performance is not as good as J4 material. It is suitable for ordinary shallow deep drawing and large angle deep drawing products such as decorative panels, bathroom products, sinks, and product pipes. J2, J5: Decorative tubes are easy to process, high hardness (both above 96�°), polished and beautiful, but they are easy to burst when used for square tubes or curved tubes (90�°). In terms of flat panel, due to its high hardness, the surface of the panel is more beautiful, and surface treatment such as frosting, polishing, and color plating can be carried out. But the biggest problem is bending, bending is easy to break, planing is easy to burst, so the ductility is not good. J3: High carbon, low chromium and low copper, but because of its high carbon content and low copper content, the material is slightly harder, so it is not suitable for bending with a slightly stronger strength. Compared with 201 stainless steel J1 material, the ductility is not so good, and it is easier to rust in the same environment. 201 stainless steel coil In the field of narrow bands, the emergence of 201 stainless steel J3 can better meet the requirements of pipe manufacturers for corrosion resistance and deformation. Because it can reduce the cost of raw materials for pipe manufacturers, it is sought after by pipe manufacturers in the narrowband field. J3 material is easy to process in veneer, but not difficult. The master of the processing factory said that he used J3 material to bend the board, and there would be an inner seam after it was broken (for black titanium, color board series, sanding board, when it is broken apart, there will be an inner seam when folding). The material of the sink has been bent 90 degrees, and it will not work if it continues. J4: The material of J4 is a relatively high-end variety in the J series of 201 stainless steel. It is suitable for deep drawing products with small angles. Most of the products that need deep drawing and salt spray test will choose it. Such as sinks, kitchen utensils, bathroom products, kettles, thermos cups, door hinges, pots, etc.
CR SS Coils | Grades : 200 , 300 and 400 series. Thickness (mm) : 0. 30 mm - 3 mm Widths (mm) : Up to 1600 mm
We are glad to propose 500 MT of stain less steel mill scale. Mill scale is formed on the outer surfaces during by the hot rolling lamination of stainless-steel products. At a visual inspection the material is a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in colour, but it also contains considerable alloying elements such as chromium and nickel. The recovery ratio after melting in furnace for the most valuable alloy elements is: - Ni: 3.5 - 4.5% - Cr: 6-8% From the chemical and physical analysis performed on the scrap, and according to the European environmental rules, the material has been classified as a special non dangerous waste, listed in green list. In particular the mill scale can be classified as follows: Waste code: 10 02 10 The material is stored on cemented flooring, and it can be loaded loose in tipper trucks or containers. Chemical analysis of the material is available on request.
Material : Stainless Steel 304 Type : Welded, Decorative Surface Treatment : Mirror:600G/800G Satin:180# 240#/ 320# /400# Thickness :0.3~2.0mm Length : 5.8meter/ 6.0meter/ 6.1meter or customized Regular Shape :Round/ Square/ Rectangle/ Oval -Click here to see all sizes Slotted Pipe : Double slotted/ Single slotted Tolerance : Out diameter: 0.2mm/ Thickness: 0.03mm ; Length: 10mm/ Weight OR Qty:15%
Stainless Steel Strip The properties of stainless steel are corrosion resistance, high ductility, attractive appearance and low maintenance. Stainless steel contains chromium which provides the properties of corrosion resistance at high temperatures. Stainless steel can withstand corrosive or chemical environments due to its smooth surface. Stainless steel products are safe for long-term use with excellent resistance of corrosion fatigue. Other specifications are also available up to request Hot Rolled Strip Available Size Width: 16.0~609.6 mm Thickness: 2.5~10.0 mm Available Steel Grade: 304, 304L, 316L Surface Finish: No.1 Cold Rolled Strip Available Size Width: 4.0~609.6 mm Thickness: 0.1~3.0 mm Available Steel Grade: 201, 202, 204 Cu3, 301, 304, 304L, 310S, 316L, 321, 409L, 410S, 420J2, 430, 439, 441, 444, 445 Surface Finish: 2B, 2D, BA, No.3, No.4, No.5, SB, HL
65Mn CK67 high carbon cold rolled spring steel strip Hardened and Tempered Steel Strip Hardened and Tempered is a thermal process that strengthens steel strips through a controlled heating and cooling process. The hardening process involves heating the steel strip to above the rapidly cooling. The steel strip in this condition is extremely brittle and requires further treatment in the tempering. Then strips are reheated to a lower temperature and holding it at the given temperature for a given period of time. This process is done in an inert atmosphere to avoid oxidation. This type of steel strip has big degree of toughness and has excellent spring properties Standard AISI, ASTM, BS, DIN, GB, JIS Place of Origin China Material Hot Rolled Surface Polished Application shutter door, plastic trowel, bricklayer trowel, putty knives, scraper, springs, metal part, shoe insole, shoe accessories, blade, band saw blade Brand Name HENSON Width 2.0mm-300.0mm Length Customize Tolerance +/-10% Hardness 40-55HRC Surface nature, blue, yellow, white, polish Edge Slit,Round,Square MOQ 1000KGS Tolerance thickness+/-0.01mm max,width +/-0.05mm max Type strip,coil,sheet Coil ID 300-500 mm Tensile Strength 540-1575N/mm2 Yield Strength 370-1475N/mm2
Material: 304/ 304L /316/ 316L/ 430/ 630 (17 4PH)/ 321/ 347...etc. Packing: Standard . Surface: HL/ No.4 / No.3 / BA / 2B / 2D. Origin: Taiwan. Secondary/baby coil also available
Steel coil- a finished steel product such as sheet or strip which has been wound or coiled after rolling. ... Hot-rolled coil is produced from semi-finished products , which are reduced to certain thicknesses by rolling and annealing and wound into a roll.
Standard: Astm, Aisi, Din, en, Gb, Jis Thickness: 0.15~4.0mm Width: 1000mm, 1220mm, 1250mm, 1500mm or Customized Length: 2000mm, 2440mm, 2500mm, 3000mm or Customized Edge: Slitting Edge or Mill Edge Surface: Ba, 2ba, No.4, Hl, Mirror, Color-coating, Etched, Embossed, Vibration or Customized
AISI 200, 300, 400 series GRADE: 201, 202, 304/304L, 310, 316/316L, 430.. FINISH: No1, 2B, BA THICKNESS: No.1 => 2.0mm~6.0mm, 2B => 0.4mm~3.0mm, BA => 0.25mm~1.5mm WIDTH: 1000mm ~ 1524mm Option: COLD ROLLED RE-ROLLING NARROW COIL THICKNESS: 0.3mm ~ 3.0mm WIDTH: 600mm ~ 1000mm