Transfer Pipet Large Bulb Disposable Thermo Scientific Samco Accurately measure more than one volume by using Thermo Scientific Samco Graduated Transfer Pipettes. Single-unit design features a built-in pipette bulb that eliminates need for plugging, packaging, autoclaving while preventing cross-contamination. Made of shatterproof, nontoxic polyethylene .Low-affinity surface reduces loss of cells and valuable proteins due to binding, Can be frozen in liquid nitrogen, or heat sealed for storage.
Transfer Pipets Aperature Aperature 62 ul Large Bulb Thermo Scientific Samco This general-purpose large aperture Samco Scientific disposable transfer pipets are made of shatterproof, nontoxic polyethylene. Non-sterile and bulk packed, the single-unit design features a built-in pipet bulb that eliminates the need for plugging, packaging, autoclaving and helps prevent cross-contamination. Their low-affinity surface reduces loss of cells and valuable proteins due to binding. They can also be frozen in liquid nitrogen or heat sealed for storage. 14 cases
Transfer Pipets 3mL Graduated, Large Bulb Thermo Scientific Samco Accurately measure more than one volume by using Thermo Scientific Samco Graduated Transfer Pipettes. Single-unit design features a built-in pipette bulb that eliminates need for plugging, packaging, autoclaving while preventing cross-contamination. Made of shatterproof, nontoxic polyethylene Low-affinity surface reduces loss of cells and valuable proteins due to binding Can be frozen in liquid nitrogen, or heat sealed for storage. 40 Cases
Two fluids, of different starting temperatures, flow through the heat exchanger. One flows through the tubes (the tube side) and the other flows outside the tubes but inside the shell (the shell side). Heat is transferred from one fluid to the other through the tube walls, either from tube side to shell side or vice versa. The fluids can be either liquids or gases on either the shell or the tube side. In order to transfer heat efficiently, a large heat transfer area should be used, leading to the use of many tubes. In this way, waste heat can be put to use. This is an efficient way to conserve energy.
Laboratory packing/experiment packing Dixon rings are used for mainly for laboratory distillation applications. The enhanced performance of the Dixon ring is based on liquid surface tension: when the mesh is wet its surface area increases greatly, with an accompanying increase in the rate of mass transfer. Dixon rings require pre-wetting (flow of liquid over the packed bed prior to starting the reaction flow). While this increases batch processing startup time, the increased
Stainless steel equipment, SS304- 316 tanks, SS hygiene fitting and seamless SS pipe, CIP system, SS centrifugal pump, SS lobe pump, homogenizer, sparkler filter, duplex filter, filter press, contra mixer, multimill, vaccum tray dryer, rapid mixer granulator, octa blender, fluid bed dryer, vibro, turbo shifter, coating plant, vacuum transfer system, ointment, cream, toothpaste plant pure steam generator, pressure and filling acid, liquid manufacturing plant, vessel rector, DM plant.
Aokeray ptfe tubing heatshrinktubesNET manufacturer from PTFE/FEP/PFA tube PTFE Teflon Insulated Tubing ,PFTE RAW MATERIAL is FROM most commonly known as DakiN a brand name .USE ON sleeve bearings, push-pull cables, non-stickroller covering etc Control Cable Assemblies ,Motorcycle Cables PTFE TUBING ,ptfe lined tubing. Car cable high temp Teflon liner ,MOTORCYCLES Cable,Hydraulic clutch, brake and oil,Clutch and brake fluid, oil transfer .PTFE hose is specified in many of the most challenging industrial applications such as those found in steel mills, foundries, transit trucks and buses and air compressors..It is also an ideal choice for vacuum/steam lines, spray paint, marine/military, aerospace, biomedical,chemical processing, industrial adhesive, paper mill.The extruded PTFE tube has excellent flex life, high temperature tolerance and superior chemical resistance.QCSS PTFE hose working temperature range is -70 to 260 degree. A reinforcement 304/316 stainless steelwire cover adds strength and durability to withstand high working pressures and harsh environments.Burst pressure reaches to 12,000 psi.Production under ISO 9001:2008 and CE control. High quality product and customer'ssatisfaction is our pursuit. Good faith cooperation. Bright future.40°C and 260°C. Applications: For transfer of high purity products, chemicals, dairy and cosmetic products. Also suitable for heat exchangers and as protective sleeve for cables. They have excellent heat resistance, viscosity, chemical resistance, electrical insulation, etc,we also help custom like annealing, beveling, bonding, printing, marking, tipping, punching, flaring ect. .Aokeray ptfe tubing,heatshrinktubesNET
Description: Orbital Shaker-Incubator is a compact bench top ShakerIncubator used for mixing of biological liquids as well as for incubation and cultivation of biological liquids according to the operator set program. Seven interchangeable platforms allow it mix and culture samples in flask, petri dish, tubes, Elisa plates, and etc. Built in microprocessor thermo controller provides constant temperature control in the incubator chamber. It is extremely easy to operate, with very straightforward setup of temperature, speed and time. Features: 1.Instantly display operation information(time, temperature and speed) on the LCD screen. 2.Gentle and reliable shaking with direct brushless DC motor. 3.Running safely �¢??-heating and shaking will be automatically stopped once the lid is open. 4.Seven interchangeable platforms can be chosen for variety demands. 5.Auto restart in case of power failure. 6.Over-heating protection device is included. 7.Built-in temperature calibration function. 8.Compact, only 421mmx320mm(DXW) Parameters: Temperature setting range 0C ~60C Temperature control range RT.+5C ~6C Time range 1min ~ 99h59min/ Temp. accuracy �±0.5C(@37C) Display accuracy 0.1C Temp. uniformity �±0.5C(@37C) Shaking range 50~300rpm Orbit 20mm Platform dimension 230x230mm Internal chamber height 182mm Load capacity 4.0kg Heating time �¢?�¤15min(from 25�?�°C to 60�?�°C) Auto resume to run Yes Power 350W Voltage AC220V/50-60HZ Fuse 250V 3A 20 Dimension(mm) 421x320x338 Weight(kg) 18.5 Optional Platforms Type Description PF-1 Platform with clamps for 5 250ml conical flask PF-2 Platform with clamps for 9 100ml conical flask PF-3 Platform with clamps for 10 50ml tube PF-4 Platform with clamps for 18 15ml tube PF-5 Platform with spring holder PF-6 Platform for 4pcs Elisa plates or deep-well plates PF-7 Flat platform for 5pcs petri dishes
With our years of experience & in-depth knowledge in this field, we are engaged in offering a quality-assured array of Electric Thermic Fluid Heater. Details: A Thermic Fluid Heater (Thermal Oil Heater) is industrial heating equipment, used where only heat transfers are desired instead of pressure. In this equipment, thermic fluid is circulated in the entire system for heat transfers to the desired processes. Combustion process heats up the thermic fluid and this fluid carries and rejects heat to the desired fluid for concluding the processes. After rejecting it, this fluid comes back again to the thermic fluid heater and this cycle goes on. Arizon Thermal Systems offers Thermic Fluid Heater / Thermal Oil Heaters fired by extensive range of fuels. Thermic Fluid Heater / Thermal Oil Heaters are available in both solid fuel firing as well as LDO /GAS / DUAl fuel firing variants so that you get the advantage of economically available fuels. Four Pass Solid (Coal / Wood) Fuel Fired Thermic Fluid Heater: The Four Pass solid fuel (coal / wood) fired Thermic Fluid Heater comprises of two heat exchangers namely radiant pass heat exchanger & convective pass heat exchanger. Radiant pass heat exchanger is a coil with conical shape & highly graded insulating material on outer surface to resist heat loss. Convective pass is made of two parallel concentric helical coils designed for sufficient convective heat transfer. This set of coils is covered with shell & this shell is insulated to resist heat loss. Radiant and convective heat exchangers are connected by a specially designed refractory duct which allows flue gas to pass from radiant to convective zone. Complete unit consist of radiant coil, convective pass, Fire chamber with sufficient grate area, F.D. fan for forced combustion, Air pre-heater to retrieve tremendous amount of heat from flue gas and transfer it to combustion air, Multi-cyclone separator to separate ash particles from flue gas & I.D. fan to induce air from the system & pass it to chimney for exhaust. Features: Efficient Heat Transfer with optimum combustion Three Pass Design for LDO / GAS fired Three Pass as well as Four pass Design for solid fuel fired Reduced excess air with balanced Draft System 300°C at near atmospheric pressure Truly maintenance Free Easy access for inspection & cleaning Energy Efficient Fully automatic in operation, so no running attention required Application: Asphalt & Road construction Dyes, Chemicals and Intermediates Textiles & Process house Packing Petrochemicals & refineries Rubber product industries Wood / ply wood industry Pharmaceutical & drugs Food processing Ceramics Reactor vessel heating, Jacketed vessel heating, autoclave & tank heating
Biomerieux Transfer Pipet Large Bulb Sterile Individual Wrap Biomerieux Produced from a custom grade of low-density polyethylene (LDPE), these unbreakable one-piece pipets are used to draw and dispense liquids in controlled, reproducible drop sizes. Plastic transfer pipets are the perfect substitute for breakable glass Pasteur pipets, which can be a danger to laboratory personnel. And, because they are completely disposable, there is never any cross-contamination which is associated with reusable rubber bulbs. An extensive selection of capacities, lengths, and tip styles are offered to accommodate different industry needs.
Weight Measurement Function: By Hours, minutes and seconds unit, Display the status of the usage of liquid gas and it can be used being installed on storage tank or tank lorry and can be carried as a portable measuring instrument. PC Monitoring Function: As the remained liquid goes below 10% of its capacity, it automatically alarms to supplement liquid gas. Thus, the appropriate time for supplement of liquid gas can be decided on time. Alarm Function: the liquid remaining of the storage tank is less than 10%, The alarm sound provides information that you can setting the a liquid supply time. Diversity Of Power Supply: Use the usual 220volt electric, in case of power outage, the built-in battery will supply the charged electricity, in addition built-in battery is operated and available for tank lorry using the car battery. Option (Printer : additional purchase): Receipt Output Function; Portable thermal transfer printer can use the output value measuring of storage tank and tank lorry without visiting a long measuring place directly by the output as a receipt.
Manual liquid electrostatic spray gun Spray - manual liquid electrostatic spray gun Feathures: 1.Reduce air pollutions 2.Reduce water pollutions 3.High transfer efficencify 4.High atomized nozzle 5.Easy handle for long term operation 6.Long life operation 7.Low voc emissions 8.Low failure rate and easy maintenance. . 9.Light weight 10.Dual coating:solvent-base , waterborne Gun weight : 470kg *(no nozzle and hv & air cables)
Aokeray ptfe tube manufacturer medicalptfeCOM ptfe Tubing Inert, non-toxic and bio-compatible properties are sought after by medical device manufacturers .Our tubing finds applications as intravenous catheters, catheter introducers, angiographic PTFE Tube ID4.35mm OD6.35mm for 3mm Filament PFTE RAW MATERIAL is FROM most commonly known as DakiN a brand name .Aokeray ptfe tubes manufacturer make class PTFE Liner MEDICAL PTFE Tubing , Medical Device Tubing, Medical Extrusion PTFE Medical Coatings ptfe tubings use on BREATHING APPARATUS ,Cylinder to pressure gauge or demand valve ,Chemical transfer hoses medical device industry etca . .OUR ALSO MAKE onvoluted Tubing , Heat Shrink Tubing , Corrugated Tubing .Types Of Tubing Medical Tubing, Ultra Pure Tubing, Spiral Cut Tubing, Coiled Tubing. Aokeray ptfe tubes manufacturer service Drilling Punching, Etching , Flanging Flaring , Paratubing , Laser Marking , Wire Wrap , Other Services . we also make Extrusion Transparent FEP Medical tube,Medical Micro-manufacturing PTFE, FEP, FEP,PVDF,XR-H PE PFA, ETFE, PET, PEEK Medical Device Tubing , Medical Extrusion Medical Grade Tubing etcs ,some size same quality alike zeus ptfe tubing. Our PTFE TUBING pass FDA products resinare made from biocompatible resins which are ISO10993-18 Class approved. Aokeray PTFE TUBINGS meets the requirements of FDA usage for medical device applications.
Perkin Elmer RoboRack 175ul Conductive Filter Tips, Sterile We offer sterile and non-sterile tips for a variety of dispenser channel sizes and volume requirements. Tips to support liquid transfers from multiple laboratory containers including test tubes, vials, troughs, deep-well plates and microplates (up to 384-well) are available as well. Our portfolio of consumables includes both cell-based and biochemical assay platforms, reagents and kits, as well as a complete range of high quality and application-focused microplates for your assay applications, detection technologies, or plate reader requirements. Our Conductive Aerosol Barrier RoboRack MPII disposable tips for use with MultiPROBE II VersaTip Plus adapters are available in popular sizes in standard format for conventional liquid sample processing, sterile, provide liquid level sensing, and are available in ten 96-tip RoboRacks per case.
Quality scientific plastics 1-200ul pipette tip yellow Quality scientific plastics They are made of high-quality polypropylene material. The pipette tips can be 121 degrees high-temperature high-pressure sterilization. Its design with plastic tubes tapered to a narrow point. They are also convenient, clean, beautiful, high efficiency. Pipette Tips can be used for laboratory analysis. They are used to transfer small quantities of liquids.
Thermo Scientific Samco 3mL Graduated, Large Bulb non-sterile Samco Accurately measure more than one volume by using Thermo Scientific Samco Graduated Transfer Pipettes. Single-unit design features a built-in pipette bulb that eliminates the need for plugging, packaging, autoclaving while preventing cross-contamination. Made of shatterproof, nontoxic polyethylene Low-affinity surface reduces the loss of cells and valuable proteins due to binding Can be frozen in liquid nitrogen, or heat sealed for storage
Thermo Scientific QSP 0.5-20ul Pipette Tip Micropoint, Clear, Non-Sterile Thermo Scientific QSP products offer high-quality consumables in a complete and innovative portfolio for your evolving liquid transfer and storage needs. Trust our economical solutions for life science research. Blending a unique combination of value and performance, QSP consumables are the products you and your research can rely on. In addition, our range of low retention tips minimizes sample retention in the pipette tip, ensuring experimental results are not compromised
NC Metal Improved Pall Ring (NC-MIPR) 1. With a larger flux and low pressure drop. 2. To further improve the ring of gas and liquid distribution in favor of mass transfer process. 3. With a wide range of operating flexibility. 4. High mechanical strength. 5. NC-MIPR Direct replacement of the widely used HY-PAK 6. Size: 25mm. 38mm. 50mm. 76mm.
+ built-in infrared smart sensor, low consumption pump design + fully automatic operation by motion activated + non-dripping innovative design eliminates any waste or mess + touchless stop germ transfer and cross-infection. Unit size: 13.5x8.3x20cm Material: abs Unit weight: 0.233kg Liquid capacity: 400ml Dispense dosage: approx 1ml~2ml Sensor range: from 2~10cm Activation time: 0.5 second Certification: ce & rohs Power: dc 6v, 4pcs aaa alkaline batteries.
Cryogenic treatment is widely used in metal processing after quenching. using liquid nitrogen as the cooling medium, making the temperature is far below the room tempreture to improve the mechanical properties of metal (the residuary austenite can fully transfer to martensite) after cryogenic treatment, the hardness, abrasive resistance,and service life of metal parts (such as: milling cutter, roller, bearing, drill, HSS tools and so on) will be highly enhanced.