Downhole motor is a kind of downhole power frilling tools by mud. The mud output by the mud pump, will enter the motor through the bypass valve, and a certain pressure difference will be formed at the inlet and outlet of motor, to push the rotor of motor to rotate, and to transfer the torque and the RPM to the drill bit via the universal shaft and the driving shaft. Drilling downhole motors offer a wide range of configurations to meet different needs. These motors have the power, torque, and speed to drill with the PDC bits for specific downhole conditions or well designs. Using the latest available technology and materials, the motors can be used in an extensive range of drilling applications, such as: Vertical, directional, and horizontal wells High temperature
Drill subs are an important integral part of everyday drilling. Not having the right thread adapter can make your life miserable. We have a large inventory of common and not so common sizes. Custom sizes are always available. Rotary subs have two primary applications. They can be used to cross over from one connection size to another, or as the disposable component used to extend the connection life of a more expensive drill stem member. Installing a float sub (with check valve) is always a good idea when drilling in wet situations.
Description: The IBOP is a non-return valve (check valve), also called Gray Valve or BVR, is a back pressure valve used in the drill string to prevent the well from flowing uncontrollably up the drill string. It is used to hold the tool open therefore it is possible to stab the valve while the fluid is flowing through the drill pipe. With the IBOP valve installed in the drill string, it allows you to strip in hole without mud flowing through the drill sting. The IBOP valve should not be used for shut the well in while tripping.
Description: Casing Head Assembly is the adapter between the first casing string and either the BOP stack or the wellhead. This adapter may be threaded or welded onto the casing, and may have a flanged or clamped connection to match the BOP stack or wellhead.
Description: We supply drilling spools that are in line with API specification 6A. Drilling spools allow the smooth circulation of mud during drilling operations and usually have the same nominal top and bottom end connections. Side outlet may differ from each other. Top, bottom and side end connections can be hub end or flanged.
Description: Overshot is a downhole tool used in fishing operations to engage on the outside surface of a tube or tool. A grapple, or similar slip mechanism, on the overshot grips the fish, allowing application of tensile force and jarring action. If the fish cannot be removed, a release system within the Overshot allows the overshot to be disengaged and retrieved.
Description: Tubing head is a spool with flange top, flanged bottom and two side outlets. It also can be called tubing spool. Top flange is equipped with lock screws to fix tubing hanger. Tubing head is installed on top of casing head, which consists of body housing and tubing hanger. It can hang tubing string and seal the annular space between tubing and production casing. Our company can manufacturer tubing head with standard structure, which includes tubing hanger installed on the cone of body housing. Tubing hanger can be tapped with BPV thread as per request.
Dead line anchor is used as a display instrument for indicating and recording the drilling string changes in weight and pressure, helping the driller to master the working parameter and judge the drilling state in drilling operation. Its mainly composed two parts: Body and Senor. It work together with the Weight indictor.
Description: Traveling block is the freely section of the block and that contains a set of pulleys or sheave through which the drill line (wire rope) is threaded and is opposite the crown block. It include the single sheave and double sheave system.
Description: A rotary table is a mechanical device on a drilling rig that provides clockwise (as viewed from above) rotational force to the drill string to facilitate the process of drilling a borehole.
Description: Drilling hose(rotary hose)made according to API 7K spec, applies for flexible hose connection between the top of oil drilling stand pipe and vertical moved swivel joint in well drilling, well cementing, work-over and down-hole servicing operation. drilling hose is also used to adjust the installation mistake between drilling pipe line and stand pipe to avoid shake, sometimes to transfer high pressure oil and water base mud with the lowest aniline point of 60°C from the swivel pipe in high pressure, and down-hole operation high medium such as water, oil etc, drilling rotary hose can be used for prefect work too.
Description: API 6A Wellhead equipment and Christmas tree are essential for oil and gas exploitation, composed of casing head, tubing head and Christmas tree, used to connect casing string and tubing string, and seal the annular spaces between all casing pipes at all layers and between pipelines. In addition, it can be used not only to control wellhead pressure and adjust oil (gas) wellhead flow, but also for special operations, such as acid fracturing, water injection and testing, etc. It is made up of casing head, oil casing head and Christmas tree.
Description: A Swivel is a mechanical device used on a drilling rig that hangs directly under the traveling block and directly above the kelly drive, that provides the ability for the kelly (and subsequently the drill string) to rotate while allowing the traveling block to remain in a stationary rotational position (yet allow vertical movement up and down the derrick) while simultaneously allowing the introduction of drilling fluid into the drill string. Parts: bail, Gooseneck, upper shell, body, lower shell, swivel stem, shaft, sealing system etc.
Description: Cementing Plugs are used to remove the mud during cementing operations. There are two types of Cementing Plugs used in the cementing process: Bottom Cementing Plug and Top Cementing Plug. The Top Cementing Plug has a solid body that provides positive indication of contact with the landing collar and bottom plug through an increase in pump pressure. The Bottom Cementing Plug is launched ahead of the cement slurry to minimize contamination by fluids inside the casin
Downhole motor is a kind of downhole power frilling tools by mud. The mud output by the mud pump, will enter the motor through the bypass valve, and a certain pressure difference will be formed at the inlet and outlet of motor, to push the rotor of motor to rotate, and to transfer the torque and the RPM to the drill bit via the universal shaft and the driving shaft. Drilling downhole motors offer a wide range of configurations to meet different needs. These motors have the power, torque, and speed to drill with the PDC bits for specific downhole conditions or well designs. Using the latest available technology and materials, the motors can be used in an extensive range of drilling applications, such as: Vertical, directional, and horizontal wells High temperature Synthetic-, oil-, and water-based mud systems Performance drilling Extended-reach well
Description: A drill bit is a device attached to the end of the drill string that breaks apart, cuts or crushes the rock formations when drilling a wellbore, such as those drilled to extract water, gas, or oil. The drill bit is hollow and has jets to allow for the expulsion of the drilling fluid, or mud, at high velocity and high pressure to help clean
Drill subs are an important integral part of everyday drilling. Not having the right thread adapter can make your life miserable. We have a large inventory of common and not so common sizes. Custom sizes are always available. Rotary subs have two primary applications. They can be used to cross over from one connection size to another, or as the disposable component used to extend the connection life of a more expensive drill stem member. Installing a float sub (with check valve) is always a good idea when drilling in wet situations.
Description: Lake Petro provide the mud pump accord with API specifications, as per international standard and requirements. Our product offering is extensive used in drilling and fracturing for oil and water well, including: F series, P series, NB series, BW series and
Description: Hook is the importance lifting equipment for drilling, the main functions of which are suspending and lifting the drill string, replacing the drill bit, dropping the casing, and discharging the production of the slightly jammed drill, etc. Its mainly consist of the H
Description: A Draw works is the primary hoisting machinery that is a component of a rotary drilling rig. Its main function is to provide a means of raising and lowering the traveling blocks. The wire-rope drilling line winds on the draw works drum and extends to the crown block and traveling blocks, allowing the drill string to be moved up and down as the drum turns. The segment of drilling line from the draw-works to the crown block is called the "fast line". The drilling line then enters the sheaves of the crown block and it makes several passes between the crown block and traveling block pulleys for mechanical advantage. The line then exits the last sheave on the crown block and is fastened to a derrick leg on the other side of the rig floor. This section of drilling line is called the "dead line".
