Features: Chassis: 6061-T6 aluminum, .16" (4mm) thick, blue in color, heavy duty braces Drive: Four wheel shaft driven with Revo spec driveline including sealed driveshafts, pivot balls and axle carrier Wheelie Bar: 4 snap-in adjustment positions to control degree of wheelie action, easily removable if additional control isn't needed Radio: Traxxas TQ 2.4GHz Direct Sequence Spread Spectrum (DSSS) programmable system with Traxxas Link automatic model recognition that allows up to 20 Traxxas Link receivers and transmitters to be bound, transmitter automatically recalls settings for any previously bound receiver Engine: Traxxas .20 cu in (3.3cc) racing engine w/Slide Valve Carburetor, 12mm diameter IPS crankshaft, high volume dual stage air filter Starter: EZ-Start electric starting system with Traxxas's exclusive Smart-Start technology that monitors critical starting functions, sensing and diagnosing potential problems for easy starting every time Battery: Traxxas Power Cell Battery Charger: AC powered Exhaust: Maxx Resonator dyno tuned dual chamber polished tuned pipe Brake: Semi metallic, giant 1.6" (42mm) diameter Tires: 6.3" (160mm) outer diameter, 3.8" (96.5mm) inner diameter all terrain Maxx Wheels: Hurricane chrome wheels 3.8" (96.5mm) diameter, 2.75" (70mm) wide, 14mm hex size Transmission: Revo-Spec forward only two speed autoshifting with skid plate, optional reverse kit sold separately Differential: Revo-Spec sealed front and rear Ball Bearings: Full set, rubber sealed Fuel Tank: 4.2oz (125cc) Body: Trimmed and painted Shocks: Eight oil-filled Ultra with rubber pressure badders and double O-ring seals, up to ten shock mounting positions, nearly 4" (102mm) travel Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle Suspension: Sealed pivot ball WideMaxx independent Steering: Heavy duty bellcrank steering with integrated servo saver Skid Plates: Heavy-duty plastic, front and rear. Includes: New T-Maxx RTR 3.3 truck, TRX 3.3 engine, EZ Start electric starter, EZ Start battery, charger, fuel bottle, extra glow plug, metric hex hardware, air filter, two decal sheets setup DVD, antenna tube, painted body, illustrated instruction manual and 2.4GHz radio system.
Standard Chemical Pump KS3 50-250 turbine parts It is special sale. power spare parts service is committed to thermal power plants, hydropower station spare parts production and supply. Long-term for the power plant to provide a large number of steam turbine spare parts, turbine generator spare parts, boiler spare parts, turbine spare parts accessories, water turbine generator spare parts, generator cover plastic seal, steam turbine cylinder head high temperature sealant, Oil cooler, mirror plate, steam turbine heating rods and other power plant spare parts spare parts. Welcome to inquire Need more products for power plant now if you don't know where to search a product. #DF-Standard Chemical Pump KS3 50-250-DF solenoid valve dishwasher 300AA0086A floating ball valve pdf PY-40 Electrode RDJ-2000 pressure hose SMS-10-1524-C filter tank hydraulic FX-40 filters oil centrifugal oil filter stainless steel filter cartridge TZX2. Hydraulic pump PVH098R01 vacuum pump compressor 30-SPEN hydraulic line filter element WU-A250 filter element cartridge CZX.PH-40 Electric control cabinet SFBX-1300 servo valve controller 72-1303-52 S63J0GB4VPL Hydraulic oil return filter element FAX-250 Solenoid valve body 4659D78001 Seperation Filter JWUX-63 solenoid valve 4WE10J-20/AW220-50NZ5L thermal resistance testing WZPK2-230 Titeseal sealing compound 53351JG oil press filter ZL366-A25 adjustable pressure switch RC860MZ097Z air filter box BR110+EF4-50 turbine speed sensor bme tcu SMCB-01-16 LVDT TD-1 stainless steel filter cartridge WY600 Standard Chemical Pump KS3 50-250 china cartridge filter 1300R003BN4HC piston pump hydraulic 15217CH1-5004 PRESSURE SENSOR H100~190~XY350 oil filter price ASME-600-150 pleated filter cartridge TXX-63 hydraulic oil filter machine RFA-800 600MW turbine DC Emergency pump (EOP)sealing ring 70LY- high pressure hydraulic filter TZX2.BH- Oil actuator filter ZTJ300.00.07 rubber o-ring.8 HN9423 hydraulic filter price STXX-25 021 inlet filter HX-800 water filter system WFF-125-1 RaspberryPi HQ camera RPI-6MM LENS Terylene Fiberglass Strip hydraulic cartridge filter HX-25 Linear variable differential transformer of CV valve 6000TDGN Oil filter element DP1A401EA03V/-W hydraulic cartridge filter WU-1000 inlet filter SFX-950 oem oil filter SFAX.BH-250 oil transfer pump 150LY-23 hydraulic filter cross reference fram STXX-25 Filter MOT GY93-25 turbine EH oil system filter PQX-150 LP Control Valve Position Sensor HL-6-60-15 electric valve Z2804076 hydraulic oil station Double chamber oil filter GY93-25 Standard Chemical Pump KS3 50-250 DFYL-2022-11-29-ZYR
Introduction AISI A2 Cold Work Tool Steel air hardening, with maximum dimensional stability during heat treatment, offering high abrasion resistance and good toughness. Generally supplied annealed to HB 231 max. A2 steel is an air hardening, cold work, tool steel. A 5% Chromium steel which provides high hardness after heat treatment with good dimensional stability. It is heat treatable and will offer a hardness in the range 57-62 HRC. Applications AISI A2 steel takes a place in tool steel range between AISI O1 and AISI D2, offering an excellent combination of good wear resistance and toughness. It may be regarded, therefore, as a ¡¡ãuniversal¡¡À cold work steel. For cutting operations the good toughness of AISI A2 gives excellent resistance to chipping of the cutting edge. In many cases tools made from this steel have given better tooling economy than high-carbon, high-chromium steels of the D3/W.-Nr. 2080 type. AISI A2 steel has much better machining and grinding properties.It can be used to make Bending Dies, Blanking Dies, Block Gauges, Cams, Coining Dies, Cold Forming Dies, Cold Shears, Cold Trimming Dies, Forming Dies, Knurls, Machine Parts, Mandrels, Plastic Mold Dies, Punch Plates, Punchers, Reamers, Ring Gauges, Roll Threading Dies, Rolls, Shear Blades, Slitters, Stamping Dies, Threading Taps, Trimming Dies, etc. HEAT TREATMENT Forging: Heat slowly toC then more rapidly to 1050-1100 Avoid working below . Reheat as often as necessary to maintain proper forging temperature. After forging cool very slowly. Heat slowly and uniformly. Cool in vermiculite or in other insulating media. Anneal after forging. Annealing: Soak thoroughly at then slow furnace cool at a rate of not more than 20C per hour. After annealing A2 a maximum hardness of 215 Brinell may be achieved.Protect against surface decarburization using controlled atmosphere or by pack-annealing. Hardening: Pre heat slowly to 600-700and soak. Continue heating to the final hardening temperature of 950/980 and allow the component to equalise. Quench in oil or cool in air.Temper immediately after hardening. Allow to cool to 125-F before tempering. Soak time is 15 minutes per inch of thickness. Minimum of 30 minutes. Tempering: Heat uniformly and thoroughly to the desired temperature and hold for 25 minutes per cm of thickness. A2 can be double tempering, after intermediate cooling to room temperature. Temper at 200C for a balance of hardness and strength or where strength is more important than hardness.Complete equalization of temperature throughout the tools is essential for good results. Double temper. Recommended temperature is 400-1000 hot rolled and hot forged according to the customer
power system FILTER ELEMENT LX-FF14020041XR is a trading production company. Our company's products include steam turbine parts, turbine generator accessories, EHC system of various types of pumps, valves, power plants components of anti-fuel system filter and so on. The needs of the user are the only reason for the existence of the company. All members of the company will be dedicated for your questions of the offer, quality and delivery. provides multiple types of spare parts and equipments for power plant : #DF-FILTER ELEMENT LX-FF14020041XR-DF k type thermocouple WRN2-630 platinum rhodium thermocouple wire TE-209 radial piston pump hydraulic PVH098R01A250000002001AB010A AST/OPC solenoid valve sliding vane pump F3-V20-1S8S-1C11 pt100 thermocouple machine TE-104 changeover valve actuator trip solenoid valve transfer oil pump 50YW25-33 speed meter DF9011 Pro industrial centrifugal pump DFB-80-300 k-type thermocouple TE-303 axial piston pumps PV046R1K1T1NMF1 HP ball valve DN15.W-BKH-20S-16-11251.316 hydraulic screw pump KF80KZ/15F4 piston pump hydraulic PVH141R13AF30A230000002001AB01A High temperature double-screw bolt transfer pump oil 80AYP60 pt100 rtd probe thermowell WRNK2-331 Thermocouple Control W08B0691A Governor O-ring DH00.047 Relay MGR-1 axial piston pumps PVP76368R2MVP10 pump coupling 100LY-62 shaft seal mechanical N0330/2100/K/M/506B vacuum pump oil P-1607 vertical centrifugal pump DFB125-80-250-03 vaccum pump P-537 thermocouple wire WREK2-230 sliding vane pump F3-V10-1S6S-10-20 FILTER ELEMENT LX-FF14020041XR vacuum pump 243v P-1741 pressure hose SMS-12/15-915-B vacuum pump parts P1764-1 pump mechanical seal G50 Magnetic circuit breaker accelerator 235.31.08solenoid relief valve ECT5-10F-08-M-U-H5-30TB oil lubrication pump LDY60-30*4 radial piston pump A10VS0100DRS/32R-VPB12N00 water pump DFB 80-50-220 Metallic spiral gasket piston pumps PVH74QIPRM-IS vane pump parts F3-SV10-1P5P-00 servo valve G761-3033B hydraulic pump piston PV29-2R50-000 front ball head YF-A18-2A-2-15 (B2) stainless steel Thermocouple WRN2-4312 AST solenoid valve k type thermocouple 1200c TE-105 thermocouple range WRNK-321 mechanical seal for water pump BGM37G/60R-G9 screw pump stainless ACG060N7NVBP thermocouple wire type k TE-204 oil change pump 65A50X9-2 temperature thermocouple WRNK2-292 vacuum pump parts Thrust bearing of gear box HPS663 thermocouple digital WRN-230 Thermocouple Cylindrical sensor WRN2-239 0-600â?? PROXIMITY SENSOR SMCB-01/02 thermowell WRN2-239 0-600 furnace thermocouple WH-5A421.575 piston vacuum pump A10VS0100DFLR/31RVPA12NOO FILTER ELEMENT LX-FF14020041XR DFYL-2022-2-17-ZYR
More than 750,000 submersibles have been successfully installed using Sudarshan uPVC Submersible Pipe upto depths of 1150 feet. Sudarshan uPVC Submersible Pipe is manufactured in different Dia – 1” to 4” in various ranges suitable for different depths and different pump delivery pressure. We manufacture Sudarshan Submersible Pipe using double stage bi-axial orientation technology & thread using CNC machines to ensure high precision. Stringent on-line quality checks, rigorous testing in our laboratory and continuous R&D activities over a decade helps us provide our customers with unmatched quality. Sudarshan uPVC Submersible Pipe unique feature is that it can sustain submersible pump high hydrostatic pressure, which is maximum in the bottom most pipes connected to the pump and can withstand the high tensile load of pump and entire submersible filled with water, which is maximum in the top most pipes. Sudarshan uPVC Submersible Pipe is most suitable for submersible pump and a perfect alternative to conventional G.I pipes. SEPL is marketing its submersible pipe all over India through a 240 distributor network and successfully exporting to GCC and Africa. Features: Square threads – Made on CNC Machines for high precision. They enable tension free grip & easy fitment. These are high friction threads on load which do not open even on constant forward and reverse torque of the pump. Rubber Gasket & Profile ‘O’ Ring – Permanent side is fitted with rubber gasket & temporary side with profile ‘O’ Ring to absorb pump vibration & to make it leak proof. ‘O’ Ring Locking System – Provides permanent lock between coupler and pipe as well as absorbs tension from torque generated by pump, providing incredible grip. Thick & Thin – Ends of the pipe are thicker than the barrel of the pipe so that even after threading there is maximum strength in the pipe. Biaxial Orientation Technology – Provides higher tensile strength and impact resistance Comparative Performance of uPVC Submersible Submersible Pipes. Criteria SEPL uPVC Submersible Pipe G.I. / M.S Pipe HDPE Pipe Life Span Long Life-Estimated life designed for 30 years; Pipes & its square threads do not deteriorate due to corrosion or rusting; and are designed to have high load capacity 5 to 10 years Pipes and its threads get damaged due to rusting and corrosion. Very Limited life Low strength, gets damaged under high pressure in span of 2 – 3 years Energy & Fuel Consumption; & Flow of Water Smooth Inner Surface leads to low frictional loss, providing higher output & Low energy and fuel consumption Rough inner surface leads to higher frictional loss; Hence consumes more energy and fuel, & gives higher water output Relatively Rough inner surface – lower output, higher energy consuption. Maintenance : Low Maintenance Very high maintenance; Rusting of threads needs periodic removal for rethreading of pipes and cleaning rust deposits Relatively High Maintenance Leakage Rubber ‘O Ring Locking System’ and rubber seals at the joints makes it completely leak proof Always Leaks – Pipe joints are not pressure tight, rusting of joint threads Pressure can cause leakage in pipes Installation: Light weight 3 metres length pipes are easy to install & remove Pipes are very heavy and difficult to handle, requiring great efforts in installation & removal Easy to install Advantages of Sudarshan uPVC Submersible/Submersible Pipe: Long life span upto 30 years Lower investment - 30% cheaper than GI Pipe 30% Lower operational cost – smooth inner walls give higher output and save power Suitable for Food Grade – GI pipe is unfit as it contaminates water due to rusting No corrosion or rusting No maintenance required Easy to install and uninstall No bacterial growth Physical & Mechanical Properties: Property Unit Standard Specific Gravity 1.4gms/cm3 - Vicat Softening Temperature 87.3 C as per ASTM D 1525 Technical Specifications of Sudarshan Submersible / Riser Pipe for Submersible Pump : Sl Size & Type OD - Outside Dia ND - Nominal Dia Ultimate Breaking Load (Kgf) Suitable Load (Kgf) safe allowable hydrostatic Pressure (Kgf/Cm2) Maximum Installation depth (Feet) Maximum Installation depth (Meters) OD: 33mm (1") ND:25 mm 1 Deluxe 1200 720 21 700 210 2 Super Deluxe 1800 1080 30 950 300 OD: 42mm (1.25") ND:32 mm 3 Deluxe 1800 1080 21 700 210 4 Super Deluxe 2500 1500 27 900 270 5 Heavy 3000 1800 35 1100 350 OD: 48mm (1 1/2") ND:40 mm 6 Deluxe 2500 1500 21 700 210 7 Super Deluxe 3000 1800 27 900 270 8 Heavy 4000 2400 35 1100 350 OD: 60mm (2") ND:50 mm 9 Super Deluxe 3750 2250 21 700 210 10 Gold 4500 2700 27 900 270 11 Heavy 4800 2880 27 900 270 12 Super Heavy 5700 3420 35 1150 350 OD: 75mm (2 1/2") ND:65 mm 13 Super Deluxe 4800 2880 17 550 170 14 Gold 6000 3600 21 700 210 15 Heavy 7200 4320 27 900 270 16 Super Heavy 9000 5400 35 1150 350 OD: 88mm (3") ND:80 mm 17 Super Deluxe 6900 4140 17 550 170 18 Gold 8100 4860 21 700 210 19 Heavy 9600 5760 27 900 270 20 Super Heavy 12600 7560 35 1150 350 OD: 113mm (4") ND:100 mm 21 Super Deluxe 9900 5940 17 550 170 22 Gold 12600 7560 21 700 210 23 Heavy 16000 9600 27 900 270 24 Super Heavy 20500 12300 35 1150 350 NOTE: We manufacture other pressure rating pipes & pipes of OD: 140mm (5") ND: 125mm on request WEIGHT CARRYING CAPACITY OF SUDARSHAN UPVC SUBMERSIBLE PIPE WITH PRESSURE RATING OF 21KGF/CM2, SUITABLE FOR SUBMERSIBLE PUMP INSTALLATIONS UPTO 210 METRES (700 FT) DEPTH Size & Type PIPE WEIGHT (Kg) For 210m Length Submersible Water Weight (Kg) For 210m Length Pump Set Weight (Kg) Approx. Cable Weight (Kg) Approx Total Weight (Kg) Max Load Capacity (Kg) For Pulling with Chain Pully Or Crane Ultimate Breaking Load (Kg) 1'' Deluxe 123 105 65 55 348 720 1200 1.25'' Deluxe 140 193 85 55 473 1080 1800 1.5'' Deluxe 182 266 130 55 633 1500 2500 2'' Super Deluxe 273 455 200 75 1003 2280 3800 2.5'' Gold 483 711 270 75 1539 3600 6000 3'' Gold 647 1022 350 95 2114 4860 8100 4'' Gold 1015 1733 500 145 3393 8100 13500 Selection of Pipes The pipe should be selected such that the pump delivery pressure does not exceed the hydrostatic allowable pressure of the pipe. Example: Pump Delivery pressure: 24kg/cm2 Pipe outlet Size & Pipe Size: 2’’ (50mm) Nominal Diameter 2’’ Super Delux recommended permissible pressure: 21kg/cm2 2’’ Heavy recommended permissible pressure: 27kg/cm2 In such case, 2’’ Heavy pipe should be selected. INSTALLATION PROCEDURE 1. First connect the male end of C.I/ M.S/ S.S bottom adaptor to submersible borewell pump using chain wrench. 2. Join the Sudarshan Pump Guard to the bottom Adaptor along with M.S/ S.S flange rod. 3. Now connect the first pipe to the female end of the pump guard. 4. Before connecting the pipes and pump guard, clean the threads with clean water and check for proper fitment of rubber sealing. 5. While fitting of pipe hold the coupler by hand / wrench. 6. Tighten the pipes by hand, until the rubber sealing in the pipe end completely enters into the coupling. However for better grip strap wrench can be used to hold/ tighten the pipes. 7. At the time of lowering the pump into submersible, the clamp must be fastened only to the portion marked as “Clamp Here”, i.e. just below the coupler. 8. Then all the other Sudarshan Submersible pipes can be connected the same way. Pipe wrench should not be used for support. 9. Once the top submersible pipe reaches the ground level, connect the top adaptor with male end connection. 10. Finally from the ground level regular plumbing accessories can be used to transfer water to required delivery point. Do not use oil on square threads of Sudarshan Submersible Pipes. Clean the threads with normal water and check the proper fitment of rubber sealing element INSTALLATION CONDITIONS: Full casing of bore well is recommended for long life of bore and pump. It prevents the pump from getting stuck due to lose boulders and stones. It also reduces chances of accident due to protruding stones and boulders at the time of removing the pump and pipe. In areas with loose soil & silt, Bore collapse problem may be more than in rocky areas. However, even rocky areas may have loose boulders. Hence, it is advisable to use full casing. PRECAUTIONS: Avoid Dry Run of Pump During dry run the submersible pump gets heated up and may damage or deform only the first pipe connected with the pump. Ways to avoid the dry running/ damage or deformation of the pipe: - Use timer switch to turn on or off the pump automatically as per the pre-set time. Pre-set time must be determined after assessing the bore yield to ensure pump does not run in dry condition. - Use of 3 metres of Steel Pipe between pump and SEPL uPVC Submersible Pipe will help dissipate the heat, preventing any damage or deformation. However, if the deformation is happening in any pipe other than the one connected to the pump, it is due to high pump pressure and wrong pipe selection. Prevention of Water Hammer At the time of pump stoppage, water recedes/falls at tremendous speed from a height. Especially in deep bore wells of about 500 ft & above, this creates enormous pressure and load on the pump and bottom most pipe called as water hammering. For such deep bore wells, it is recommended to make a 3mm hole in the pump NRV to protect the pump and pipe from water hammering. Handling & Storage of Pipes - Check for any visible damage to pipes during transit and inform immediately. - Avoid contact of pipe with any sharp objects. - Do not throw or drop the pipes from truck to the ground. - Store it in covered areas to avoid exposure to sunlight & UV rays - Stack pipes on even grounds with stack height not more than 7feet - Place alternate layers of pipes/bundles perpendicularly, with each layer forming a square. - Stack lighter pipes above the heavier ones, if pipes are of same diameter - Keep the stacking surface dry.
Sihanming FAKRA connector is one of the auto parts. They are widely used in GPS, Remote control, car phone, car TV, hi-fi equipment, antennas, etc. It is mate with the same colors or connector and socket, and the structure is to be double-locked and fool-proofing for them FAKRA Straight Female Connector Major characteristics: � � Double-locked, fool-proofing assembly with the color and the structure The connector is be protected by the cap . Easy to assembly Many difference between the connector and the cap. The product technical characteristics: Body: Brass, Ni-plated Socket: beryllium-copper, Gold-plated Pin contact: Brass Insulator: PTFE Fakra Female Crimp Solder Connector wholesale Crimp ferrule: brass, Ni-plated O-ring: beryllium-copper Shell: PA66+30%GF Technical characteristics
Rod seal:single acting seal such as u seal;double acting seal like stepseal Piston seal:single acting seal such as u seal;double acting seal like glyd ring;combined seal like vee seal Wiper:single lip wiper and double lip wiper. Wear ring:cutting ring and non-cutting ring. Rotary seal and oring Paper box:300mm*300mm*300mm
FAKRA Connector is one of the auto parts. They are widely used in GPS, Remote control, car phone, car TV, hi-fi equipment, antennas, etc.FAKRA Straight Female Connector is mate with the same colors or connector and socket, and the structure is to be double-locked and fool-proofing for them. double locked Female Connector factory Major characteristics:   Double-locked, fool-proofing assembly with the color and the structure   The connector is be protected by the cap .   Easy to assembly   Many difference between the connector and the cap. The FAKRA right angle Female Connector technical characteristics:   Body: Brass, Ni-plated   Socket: beryllium-copper, Gold-plated   Pin contact: Brass   Insulator: PTFE   Crimp ferrule: brass, Ni-plated   O-ring: beryllium-copper   Shell: PA66+30%GF GPS FAKRA Connector Technical characteristics   Impedance: 50   Frequency Range: 4GHz   Withstanding Voltage: 1000V(RMS)   Contact resistance:   Center contact: 20m   Outer contact: 10m   Insulation: 1,000M   VSWR: DC - 2GHz
Brass road , brass angale cock, brass pindal, brass chand , brass 1014 1/2" bsp elbow, brass 16mm knurling bush, brass 25mm knurling bush, brass leg, brass 1/2" hex nut, brass 3/4 female, brass 9 gram female, brass 16 gram female, brass 1" male/female, brass double stud, brass single stud, brass kangi, brass 2025 equal t, brass 1620 split ring, brass midium ring.
The NRS ductile iron resilient seated gate valve, which is epoxy coated, can be safely used in municipal water supply,sewage and plumbing etc. material list: 1.Body-QT450-10 2.Bonnet gasket-EPDM 3.Wedge-QT450-10+EPDM 4.Stem nut-ZCuAl10Fe3 5.Bonnet-Qt450-10 6.O ring-NBR 7.Support bush-ZCuAl10Fe3 8.Gland housing-Qt450-10 9.Dust seal-NBR 10.Stem-2Cr13 11.Handwheel-ZG35 12.O ring-NBR 13.Packing ring-PTFE 14.Sealant-Parafin 15.Female hax head screw-Carbon Steel 16.O ring-NBR 17.Female hex head screw-Carbon Steel 18.Guide shoe-POM ply-wood package
WRAS approved,NRS ductile iron resilient seated gate valve,size from DN50-DN800,pressure from PN10/PN16. material list: 1.Body-QT450-10 2.Bonnet gasket-EPDM 3.Wedge-QT450-10+EPDM 4.Stem nut-ZCuAl10Fe3 5.Bonnet-Qt450-10 6.O ring-NBR 7.Support bush-ZCuAl10Fe3 8.Gland housing-Qt450-10 9.Dust seal-NBR 10.Stem-2Cr13 11.Handwheel-ZG35 12.O ring-NBR 13.Packing ring-PTFE 14.Sealant-Parafin 15.Female hax head screw-Carbon Steel 16.O ring-NBR 17.Female hex head screw-Carbon Steel 18.Guide shoe-POM ply-wood pallet
1 single cartridge seal type :GSE-108CRTS single cartridge seal, SUITABLE For petroCHEMICAL , chemistry and paper making,medical industry.globe star mechanical seal manufacture . is the advanced designer & manufacturer of mechanical seal, the range involves in: industrial pump mechanical seal, mixer and agitator seal, cartridge seal, metal bellows seal, auto cooling pump seal and auto air-condition compressor lip seal. Globe products can replace the mechanical seals produced by John Crane and Burgmann and be widely used in petroleum, chemistry, refinery, paper making, pharmacy, power and auto industry. OPERATING LIMITS Rotary Ring:SiC/Carbon/TC/stellite ;Stationary Ring:SiC/Ceramic/TC ;Secondary Seal:VITON/PTFE Coated VITON/PTFE /NBR/EPDM /calrez Other Parts :SsS304/SsS316/Hastelloy-c 2 GROUNDFOS TYPE CARTRIDGE SEAL type :GSE-108CRTGF Grundfos pump seals are defined as an typical O-ring seal of the cartridge type.Different models of mechanical seal for a wide variety of Grundfos pumps,among them:CRN,NB,NK,CLM,LP,TP,CRR ETC. Available in diverse combinations of materias and different diameters:12,16,22,etc.Also mechanical seals for the waste water pumps.Available in various materials:silicon-graphite carbide,silicon carbide- silicon carbide,combined with EPDM AND FKM elastomers. 3 cartridge seal type :GSE-108CRTBL For petroleum, chemistry and paper making single cartridge seal OPERATING LIMITS Temperature: -40℃～+204℃ Pressure: ≤5.17MPa Speed: ≤23m/s Rotary Ring:SiC/Carbon/TC ●Stationary Ring:SiC/Carbon/TC ●Secondary Seal:VITON/PTFE Coated VITON/PTFE ●Other Parts :SSS304/SSS316/Titanium/Hastelloy-C 4 dual cartridge seal type :GSE-108CRTD DOUBLE cartridge seal, For petroleum, chemistry and paper making,medical industry.globe star mechanical seal manufacture . is the advanced designer & manufacturer of mechanical seal, the range involves in: industrial pump mechanical seal, mixer and agitator seal, cartridge seal, metal bellows seal, auto cooling pump seal and auto air-condition compressor lip seal. Globe products can replace the mechanical seals produced by John Crane and Burgmann and be widely used in petroleum, chemistry, refinery, paper making, pharmacy, power and auto industry. OPERATING LIMITS Temperature: -20℃～+280℃ Pressure: >1.6MPa Rotary Ring:SiC/Carbon/TC/stellite ●Stationary Ring:SiC/Ceramic/TC ●Secondary Seal:VITON/PTFE Coated VITON/PTFE /NBR/EPDM /calrez ●Other Parts :SsS304/SsS316/Hastelloy-c 5 METAL BELLOW Cartridge Seal type :GSE-108CRTM high temperature, non-pusher rotating welded metal bellows single seal with the flexible element cartridge design. A rugged API 682 mechanical seal for handling high pressures and high temperatures environments, which also has the flexibility to be fitted in an ANSI+ and DIN standards. Pressure: 0~2.5Mpa Temp.: -30ºC~300ºC Speed: ≤25 m/s 6 heavy duty cartridge seal type :GSE-108CRTHY Mechanical Seal type cartridge for high pressures heavy duty in petrochemical industry and sealing of wide range of products such as crude, gasoline, LPG, water with muds. Designed according norm API682 Materials Seal Body : SS 316 .SS304,MS Outboard Faces : Metallized Carbon, Silicon Carbide (RB),TC,CERAMIC Inboard Faces : Silicon Carbide (RB), Tungsten Carbide (Ni), Metallized Carbon Elastomers : Viton, EPR, Chemraz, Kalrez,.TTV Springs : Hastealloy C, AISI 316 As per customer requirement we would able to provide packaging details.
We can supply below products: a, WALFORM plus Cutting ring; b, WALFORM tube fitting; c, Cutting ring tube fittings; d, Cutting Ring Tube Coupling; e, Weldable Straight Stud Coupling; f, Weldable Straight Coupling; g, Reduce Coupling; h, Straight Coupling; i, Ajustable Gauge Coupling; j, Manometer Coupling with Seal Ring; k,Double Banjo Coulping with One-piece Bolt; l, Banjo Coulping with One-piece Bolt; m, Female Stud Coupling; n, Parallel Female Stud Coupling; o, Ajustable Male Stud Tee-Stud with Lock Nut; p, Ajustable Equal Tee with Lock Nut; q, Ajustable Elbow Couplings with Lock Nut; r, Ajustable Run Tee; s, Ajustable Stud Branch Tee; t, Ajustable Stud Elbow; u, Ajustable Equal Tee; v, Ajustable Equal Elbow; w, Female Reducer; x, Reducing Fitting; y, Reducing Tee; z, Straight Reducing Coupling; 1, Meeting the requirement of ISO8434, ISO9974, ISO1179, DIN3870, DIN3861 and other international standards; 2, Material: 304, 316L, 45#, etc; 3, Suitable for OD 6mm-42mm of carbon steel or stainless steel pipeline; 4, Working pressure: 10-63MPa; Products are tested strictly by qualified third-party lab, our company could offer complete set of Type Test Reports and Customized Solutions to meet the hoghest expectations of customers
FAKRA Connector is one of the auto parts. They are widely used in GPS, Remote control, car phone, car TV, hi-fi equipment, antennas, etc.FAKRA Straight Female Connector is mate with the same colors or connector and socket, and the structure is to be double-locked and fool-proofing for them. double locked Female Connector factory Major characteristics:   Double-locked, fool-proofing assembly with the color and the structure   The connector is be protected by the cap .   Easy to assembly   Many difference between the connector and the cap. The FAKRA right angle Female Connector technical characteristics:   Body: Brass, Ni-plated   Socket: beryllium-copper, Gold-plated   Pin contact: Brass   Insulator: PTFE   Crimp ferrule: brass, Ni-plated   O-ring: beryllium-copper   Shell: PA66+30%GF Eaton NPR48-ES Energy Saver Rectifier Module Power Module Features 3000W output power Energy saving efficiency greater than 96% Wide efficiency curve Industry leading power density Fast on-line expansion of rectifiers (hot-swap) Simple plug and go insert Unity power factor Digital signal processing for enhanced control Wide AC supply conditions Wide output voltage range Constant power output Compliance with international standards Description The Eaton NPR48-ES Energy Saver Rectifier is designed for communications network operators who are striving to cut energy costs across the network, and/or to meet aggressive carbon footprint reduction targets. Operating with well over 96% efficiency, it produces at least 50% less waste energy than most other modern rectifiers, and with potentially greater savings over older infrastructure. The NPR48-ES Energy Saver Rectifier harnesses the technology of the APR48-ES 2kW rectifier to offer a powerful 3kW of output power. This rectifier features intelligent digital signal processing for enhanced control, producing peak efficiency in excess of 96% for typical operating loads, while also maintaining a very high minimum operating efficiency of 95 to 96%, over a very wide range of loads. The high power density, short depth and flexible mounting options makes the Energy Saver Rectifier well suited to limited space applications such as ETSI and road side cabinets. The Energy Saver Rectifier is fully compatible with the existing Eaton SC200 system controller and it is one of the easiest rectifiers to use, with a simple plug-and-go insertion. It operates under a wide range of AC power conditions and in temperatures at up to 70C (158F). Specifications Input AC Supply 120V/208-240V, 50/60Hz (nominal) 185-275V full output power up to 50C [122F] 90-185V reduced output power Power Factor >0.99 (50 100% output current) Efficiency >96% peak >95% (20 100% output power) Output DC Output Voltage Range 43.2 57.5V DC Output (maximum) 3000W, 60Amp at 50V Environmental Operating Temperature Range -40C +70C [-40F +158F] Output power derates above 50C [122F] Cooling Temperature controlled, variable speed, high reliability fan
1. DOUBLE ACTING PISTON SEALS Double-acting piston seals have a symmetrical profile cross section & identical sealing functions in both directions. 2.SINGLE ACTING PISTON SEALS A single-acting piston seal is designed for cylinders where pressure is applied from one side only. 3.ROD SEALS Rod seals maintain sealing contact in sliding motion between the cylinder head and the piston rod. 4.OIL SEALS Rotary seals are use in rotating equipment like gear box, pumps, motors etc to retaining lubrication in bearings. 5.FABRIC SEALS Fabric seals are flexible rotary seals mfg in cotton fabric reinforced body having spring loaded rubber sealing lip 6. METALLIC OIL SEALS High pressure rotary seals are capable to withstand under high pressure application such as hydraulic pumps or motors, power steering application etc. 7. V SEALS V-Rings are use as an dust seal or a guard in avoid ingression of the water or colant in the bearing chock. 8. U CUP SEAL U-cup seals, as their name implies, have a U-shaped profile, including an outside static sealing lip and an inside dynamic sealing lip. 9. PNEUMATIC ROD SEALS Pneumatic seals operate in dynamic applications, often at high speeds, generally with rotary or reciprocating motions. 10. PNEUMATIC SYMMETRICAL SEALS where cylinders and valves are actuated by air pneumatic seals plays a vital role.
MFG-CW-302 Colors: all color avilable Sizes: All Size Available Customize hoodies 100% combed, ring-spun cotton jersey. Cotton fleece Pullover/Zipper Double lined hood Modern Classic Fit Contrast inner lining to hood Deep front pouch pocket Contrast drawstring and toggles Ribbed cuffs and waistband Reactive dyed for color stability Custom colors & sizes Custom Printing / Embroidery Logo offer Available in Custom Colors & sizes
MFG-CW-303 Colors: all color avilable Sizes: All Size Available tomize hoodies 100% combed, ring-spun cotton jersey. Cotton fleece Pullover/Zipper Double lined hood Modern Classic Fit Contrast inner lining to hood Deep front pouch pocket Contrast drawstring and toggles Ribbed cuffs and waistband Reactive dyed for color stability Custom colors & sizes Custom Printing / Embroidery Logo offer Available in Custom Colors & sizes
MFG-CW-304 Colors: all color avilable Sizes: All Size Available Customize hoodies 100% combed, ring-spun cotton jersey. Cotton fleece Pullover/Zipper Double lined hood Modern Classic Fit Contrast inner lining to hood Deep front pouch pocket Contrast drawstring and toggles Ribbed cuffs and waistband Reactive dyed for color stability Custom colors & sizes Custom Printing / Embroidery Logo offer Available in Custom Colors & sizes
MFG-CW-305 Colors: all color avilable Sizes: All Size Available Customize hoodies 100% combed, ring-spun cotton jersey. Cotton fleece Pullover/Zipper Double lined hood Modern Classic Fit Contrast inner lining to hood Deep front pouch pocket Contrast drawstring and toggles Ribbed cuffs and waistband Reactive dyed for color stability Custom colors & sizes Custom Printing / Embroidery Logo offer Available in Custom Colors & sizes
MFG-CW-306 Colors: all color avilable Sizes: All Size Available Customize hoodies 100% combed, ring-spun cotton jersey. Cotton fleece Pullover/Zipper Double lined hood Modern Classic Fit Contrast inner lining to hood Deep front pouch pocket Contrast drawstring and toggles Ribbed cuffs and waistband Reactive dyed for color stability Custom colors & sizes Custom Printing / Embroidery Logo offer Available in Custom Colors & sizes
