Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:SGCC/JIS G3302/JIS G3321/DX51D+Z/TDC51DZM/TDC52D Model Number:SDXFA05 Type:Steel Plate Technique:Cold Rolled/Hot Rolled Surface Treatment:Galvanized Application:Roofing, Wall Construction, Painting Basis Sheets & Auto Indust Special Use:High-strength Steel Plate Width:600mm-1250mm Length:Customer's Requirement Shape:Flat.sheet Color:RAL Thickness:0.12MM-2.0MM Tolerance:Thickness:+/-0.02mm Width: +/-2mm Packing:Standard Seaworthy Packing
Corrugated Sheet Roofing, Corrugations Corrugated sheet roofing material is widely available and easy to use. Corrugations should run in a straight line between the highest and lowest points, and at a right angle to the purlins (the intermediate supports). The overlaps (ends and sides) depends upon the sloop of the roof. Purlin spacing should suit the end laps required for the size of sheet to be used. Sheets should be laid so that the side overlaps are directed away from the prevailing wind. All purlins should be in one plane and parallel to each other. They should be properly anchored to the supporting superstructure. Ends of all sheets should be supported by purlins. The free overhang at the eaves should not exceed 300 mm. 8 mm diameter (min) hook bolts, crank bolts or coach screws, should be inserted through 10 mm diameter drilled holes.- NEVER PUNCHED - in the crown of the corrugations. Nuts or screws should be tightened lightly at first, and then tightened again when a dozen or more sheets have been laid. At intermediate purlins, they should not be tightened in an attempt to make the sheet rest on the purlins. A cat-ladder or roof board should always be used when working on a roof for safety of the person and to avoid damage to the roofing material. Installation of corrugated roof sheeting These notes are intended to cover the use and installation of corrugated roof sheets such as PVC, other plastics and bitumen fibre sheets. Although very different as materials and where they are used, they do have similar properties regarding flexibility and weight. One advantage of these corrugated materials is that it is far more rigid than a flat sheet of a similar type and thickness. This enables considerable savings in both weight and cost, it also makes the sheet relatively easy to handle. Generally all these types of material can be used either as roofing or vertical cladding. Most of these sheeting tends to be susceptible to condensation when used as cladding for outhouses etc. - being relatively thin they tend to have low thermal insulation properties. Condensation will be reduced if the interior of the structure is well ventilated.
Bar mops, dish cloth, duster cloth, floor cleaning cloth, stockinet rolls, face cloth, hand towels, bath towels, beach towels, kitchen towels, tea towels ( stripped, checked, printed, embroidered, jacquard ), waffle weave kitchen towels, glass cloth, herringbone kitchen towels, terry tea towels, mono check tea towels, aprons, pot holders, hot pad, oven mitts, silicon oven mitt, terry oven mitt, pan grabbers, chef hat, caps, socks ( cotton, polyester ), cotton rag rugs & mat, bed sheets, table cloth, napkins, cushion covers, thermal blankets, fleece blankets, mink blankets, floor carpet, cotton bags, tote bags, shopping bags, jute bags, paper / board bags, fruit picking bags, coin bags, cotton webbing tape, cotton/ polyester braided cards, home textiles & made ups, jute webbing, pp webbing, soft plant tie, coconut coir pith / peat..
Metals and minerals, steel products and agricultural products 1 steel tubes/pipes (ssaw, lsaw, erw and seamless steel pipes) 2] galvanized steel coils 3] galvanized steel sheets 4] pre painted galvanized steel sheets/coils 5] corrugated steel sheets 6] deformed steel bars / re inforcing steel bars 7] wire rods 8] wire nails 9] stainless steel coils 10] steel fence bar 11] steel strips 12] flat / round / square bars 13] pipes / fittings / flange 14} steel billets 15 agro products rices, pulses, sesame seeds, peanuts.Traders
Latex surgical & exam. gloves, latex o.b. gloves, latex long cuff gloves for industrial grade, latex male catheters, latex penrose tubing, nitrile exam, gloves, nitrile gloves for industrial grade, wound dressings, medical tapes, face masks.
Product:Aluminium Brand:Renaissance Pipe Fitting Inc. Sizes:Refer the specification Condition:New Rating:4.4, based on 65 reviews price:Start from 20 USD ANSI/ASME, Aluminium Tubes, Aluminium Pipe Bends, Aluminium Seamless Extruded Pipes, Aluminium Elbows, Aluminium Rods, Suppliers RFP India is India's leading manufacturer of aluminium, which are made from high standard quality hot rolled bars or plates. Our production proficiency comprises an absolute variety of aluminium butt weld fittings, aluminium pipe bends and aluminium seamless extruded pipes in accord with ANSI/ASME and DIN standards. At RFP, aluminium products are made up from rolled aluminium bars and plates, and not from cast aluminium, making it most appropriate for special applications. Aluminium is often supplied devoid of any surface treatment, for the reason that the aluminium oxide layer formed on the surface of it shows RFP India is India's leading manufacturer of aluminium, which are made from high standard quality hot rolled bars or plates. Our production proficiency comprises an absolute variety of aluminium butt weld fittings, aluminium pipe bends and aluminium seamless extruded pipes in accord with ANSI/ASME and DIN standards. At RFP, aluminium products are made up from rolled aluminium bars and plates, and not from cast aluminium, making it most appropriate for special applications. Aluminium is often supplied devoid of any surface treatment, for the reason that the aluminium oxide layer formed on the surface of it shows enough resistance to corrosion in usual atmosphere. Meanwhile, Aluminium elbows and bends are in general made up from 6000 series aluminium pipes that meet the needs for strength, anodizing and welding.
We provide a wide range of Aluminum sheets, which are manufactured using qualitative raw materials We provide plates in different alloys. Used in diverse industrial applications, available in the following sizes,we can also provide customized solution and cut to length service.
Stainless steel coil , sheet, pipe and tubes.
Material Galvanized Iron Length 5-10 ft Feature Corrosion Resistant, Tamper Proof Surface Treatment Galvanized Usage/Application Roofing
Number:SLADE-RFS Specifications:Thickness 0.2-1.4mm Classification:Roofing sheet Introduce:Material: galvanized, prepainted, aluminum etc Thickness: 0.2mm-1.4mm Width: 800mm-1000mm Types and materials for roofing sheet: CGCC, DX51D Zinc Coating white, red, blue PRE PAINTED Corrugated steel Roof Sheets / SheetPRE-PAINTED CORRUGATED ROOFING SHEET Thickness: 0.11mm to 1.4mm Width: Plain 400mm to 1000mm Corrugated: 665mm to 1000 mm Length: 1600 to 4500 mm Zinc Coating: 80 to 275 GSM Crest: 16.5mm Pitch: 76.2mm Waves per Sheet: 12 Color: White, red, blue or customized as per RAL color card Main application:Roofing, metope adornment, various internal and external pack material, suitable for the requirement of any building. Specifications of Corrugated roofing sheet : 1) Material: carbon steel, galvanized steel, pre-painted steel, aluminum roofing sheet etc. 2) Thickness: 0.11 mm-1.4mm 3) Width: 400mm-1000mm 5) Length:2 to 9 meters or customized.
Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:Steel Model Number: models of steel sheets Type:Steel Plate Technique:Cold Rolled Surface Treatment:Coated Application:Roofing sheet, building, steel structure Special Use:High-strength Steel Plate Width:600 mm - 1250 mm Length:1 m - 11.8 m Hardness:40 HRB - 95HRB Yield Strength:>240 Mpa Tensile Strength:270-550 Mpa Surface:With pvc protection film Delivery Time:Within 10 days after the receiving deposit Color:RAL standard
Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:Galvanized steel coil Thickness:0.12~3.0 mm Model Number:Steel Coil Type:Steel Coil Technique:Cold Rolled Surface Treatment:Coated Application:Structure, Roofing, Building Special Use:High-strength Steel Plate Width:As request Length:As Request Product Name:PREPAINTED GALVALUME GI GL Color:RAL Color Flower Design Surface:Painting Coil ID:508-610MM Payment:TT LC Material:SPCC DX51D Coil Weight:3-8 Tons Certificate:SGS Shape:Flat.sheet Zinc Coating:40-275g/m2
Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:Q195/Q235/Q345/Q390 Type:Steel Plate Technique:Hot/Cold rolled Surface Treatment:Galvanized Special Use:High-strength Steel Plate Width:600~1250mm Length:As per customer's demand, 1-6m Secondary Or Not:Non-secondary Production Standard:GB3091,DIN1626,EN10217 ASTM BS Material:Q195/Q215/Q235/Q345 Shape:Round Square. Rectangular Oval Usage:Construction Structure End protector:Plastic Pipe Cap Surface:Galvanized Ends:coated
Standard:AISI, ASTM, BS, DIN, GB, JIS, JIS G3302,ASTM A653,etc. Grade:DX51D,DX52D,SGCC,CGCC Model Number:SGCC,CGCC,DX51D,DX52D Type:Steel Coil Technique:Cold Rolled Surface Treatment:Galvanized Application:construction Special Use:High-strength Steel Plate Width:500-1250mm Length:Customers' Requirement Name:top quality galvanized sheet metal corrugated roofing sheets Surface treatment:chromed / skinpass/ oiled/slightly oiled/ dry/ anti-fingerprint Material:SGCC,CGCC,DX51D,DX52D Zinc coating:80g/m2 Coil ID:508/610mm Thickness:0.8mm Payment:T/T L/C Western Union Packing:kraft paper and steel sheet for 80g/m2 PPGI/PPGL color:according your requirement
Standard:AISI, ASTM, BS, DIN, GB, JIS, ISO Grade:SPCC Thickness:0.14-0.7mm Model Number:as the order Type:Steel Coil Technique:Cold Rolled Surface Treatment:Coated Application:roof Special Use:no Width:As your request Length:request Product Name:Prepainted Galvanized Steel Coil Surface:Galvanized Coated Material:ASTM/AISI/SGCC/CGCC/TDC51DZM/TDC52DTS350GD/TS550GD/DX51D+Z Q195-q345 Color:RAL Shape:Plate. Coil Coil Weight:3-8 Tons Keyword:Prepainted Zinc Steel Coil MOQ:25 Tons Payment term:L/C T/T (30% Deposit) Delivery time:15-20 Days
Standard:AISI, ASTM, BS, DIN, GB, JIS, JIS G3302,ASTM A653,etc. Grade:DX51D,DX52D,SGCC,CGCC Model Number:SGCC,CGCC,DX51D,DX52D Type:Steel Coil Technique:Cold Rolled Surface Treatment:Galvanized Application:construction Special Use:High-strength Steel Plate Width:500-1250mm Length:Customers' Requirement Name:top quality galvanized sheet metal corrugated roofing sheets Surface treatment:chromed / skinpass/ oiled/slightly oiled/ dry/ anti-fingerprint Material:SGCC,CGCC,DX51D,DX52D Zinc coating:80g/m2 Coil ID:508/610mm Thickness:0.8mm Payment:T/T L/C Western Union Packing:kraft paper and steel sheet for 80g/m2 PPGI/PPGL color:according your requirement
Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:galvanized steel coil Thickness:0.12~3.0 mm Model Number:Steel Coil Type:Steel Coil Technique:Cold Rolled Surface Treatment:Coated Application:Structure, Roofing, Building Special Use:High-strength Steel Plate Width:As request Length:As Request Product Name:PREPAINTED GALVALUME GI GL Color:RAL Color Flower Design Surface:Painting Coil ID:508-610MM Payment:TT LC Material:SPCC DX51D Coil Weight:3-8 Tons Certificate:SGS Shape:Flat.sheet Zinc Coating:40-275g/m2
Standard:AISI, ASTM Grade:steel Model Number:400 Type:Steel Coil Technique:Cold Rolled Surface Treatment:Coated Width:914-1250 zinc coating:40-275g/m2 color:RAL color Certification:ISO9001/CE application:structural roofing, container plate special use:high-strength steel plate service:good after-sale service 20' load:around 25T Property:long use time Product Name:PPGI Coils/ Color Coated Steel Coil Surface treatment:Painted
Standard:AISI, ASTM, BS, DIN, GB, JIS Grade:SGCC,CGCC,DX51D-Z,DC51D-Z Model Number:CGCC Type:Steel Plate Technique:Cold Rolled Surface Treatment:Galvanized, Application:building,construction,roofing sheet Special Use:High-strength Steel Plate Width:1000mm,1200mm Length:in coil or as request Product Name:corrugated steel sheet Surface:Galvanized Color:RAL Colors Certificate:ISO9001,BV,SGS Zinc Coating:30-275g/m2 Payment term:TT/LC Material:SGCC,CGCC,DX51D-Z,DC51D-Z Shape:steel plate Thickness:0.13-0.7mm
Standard:AISI, BS, DIN, GB, JIS Grade:DX51D Model Number:00005 Type:Steel Plate Technique:Hot Rolled Surface Treatment:Coated Application:Flange Plate Special Use:High-strength Steel Plate Width:665-1000mm Length:1000-6000mm
