Rock wool sandwich panel is made from rock wool as the core of raw materials. Rock wool sandwich panel full play to the unique properties of rock wool core material in fire protection, thermal insulation, acoustic insulation, and so has a significant effect. Widely used in steel plants, simple activities room roof, wall, ceiling and air clean room partition. Its weak is strength not strong enough, however it is suitable for the roof and wall of the steel structure workshop and the simple movable room, and the ceiling and partition of the air clean room. Rock wool sandwich board fully exerts the unique properties of rock wool core material, and has remarkable effect in fire protection, insulation and sound insulation, sound absorption and sound insulation. 1, Excellent fire resistance: As its raw material is rock wool ,it has good fireproof performance. The test shows that its fire resistance temperature can reach upto 1000 degree. Rock wool sandwich panels have been tested by GLOROANO S.P.A, an authoritative inspection institution in Italy. According to the standards of International Standardization Organization (ISO), British BS and German DIN, the rock wool sandwich panels meet the requirements of fire protection standards, M.I14/09/61 91 and D.M.30/11/83. 2)Good thermal insulation: its insulation is according to its thermal conductivity at 0.043W/� corresponding the thickness of rock wool 3) The effect of sound absorption and heat insulation is remarkable. Sound insulation: rock wool sandwich panels have a significant reduction in noise transmission, especially for places where a designated flight is passed. In addition, after using the roof of the rock wool roof, the rain and hail impact on the roof plate of the building, causing the sound of the indoor sound and also obviously weakened. According to ISO 717/82 and UNI 8270/7 standard, Density of 120kg/m³ rock wool as core material, the sound insulation effect can reach RW=29-30 dB Sound absorption: rock wool sandwich panels have excellent attraction at the same time, which can absorb sound in a wide range of frequencies. According to the ISO 35/85 standard The sound absorption performance level of the rock wool sandwich panel reaches DELTA LA=15.7dB (A)..
Have you heard of converting waste plastic into oil? That's right, DoingGroup already has a very mature cracking device that heats waste plastics at high temperatures to crack fuel, carbon black and combustible gases. Perhaps some people do not know too much about the waste plastic pyrolysis plant. The specific operating procedures for the equipment are as follows: 1. The waste plastic into the reactor by automatic push device. 2. Reactor with fuel heating, reaching a certain temperature, waste plastics began to crack into oil and gas. 3. These oil and gas will enter the condensing system, a part of which will be liquefied and flow into the oil tank. The other part will be liquefied through the condensing system to liquefy into heavy oil and flow into the tank. 4. The resulting heavy oil will be filtered through the dedusting and deodorizing device. Remove fumes, dust particles generated during combustion of the fuel. 5. Wait until the temperature in the kettle drops below 40 C and remove the carbon black from the kettle. Know the working principle of waste plastic pyrolysis plant, equipment may be more interested in the proceeds. After our engineers accurately test and run our equipment can get nearly one million yuan a day's revenue, these benefits mainly come from the equipment cracked the fuel and carbon black. They have a wide range of uses in life, as follows: 1. Fuel oil: Mainly used in steel plants, boiler heating, heavy oil generators, cement plants. 2. Carbon black: mainly used for pressure ball burning and refined milling. Which refined flour and can be used for new tires, rubber soles, pigment manufacturing materials. So what are the unique advantages of our equipment? Specifically the following points: 1.16mm, Q245R thick steel boiler plate, curved pressure head, can withstand high temperature and high pressure. 2. Unique 3-step welding process, longer service life. 3. Currently the most commonly used and best performing condenser in the oil industry. The cooling system of the equipment is divided into three stages to ensure that the cracked oil and gas is fully cooled and the oil yield is increased. 4. A water separator, water seal, vacuum devices and other safety devices. Can purify oil and gas, exhaust, to prevent its back. And can provide negative pressure, drainage of oil and gas. Through the above introduction, you have a further understanding of our waste plastics pyrolysis plant?
DoingGroup's pyrolysis plant for waste plastic recycling is the process of pyrolyzing waste plastic into fuel oil, carbon black and non-condensable gas under the condition of anaerobic environment and utilizing the chemical reaction of pyrolysis. DoingGroup's main operating temperature pyrolysis plant: 1. Use mechanical waste plastic to enter the reactor and close the inlet to prevent gas flow out. 2. Carbon, wood or fuel heating reactor, the reactor is generally 200-300 degrees began cracking reaction, when the waste tires vaporized into oil vapor. 3. Hydrocarbons entering the condensing system are liquefied into oil and collected in the tank unit. Our system has a negative pressure device, he can greatly improve the production of pyrolysis oil. 4. At atmospheric pressure can not be liquefied petroleum gas as fuel for combustion returned to the reactor, not only energy saving and environmental protection, 5. After the oil production is completed, the reactor will be cooled. When the temperature drops to 40 degrees, the carbon black will be removed automatically or manually. The main advantages of this pyrolysis plant for waste plastic recycling are as follows: 1. Reactor manufactured according to the standard, using 16mm thick boiler steel pipe and arc pressure head, can withstand high pressure and high temperature. 2 high standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, small power, no direct contact with the reactor, heat transfer less easily deformed. 4. The tertiary cooling system uses a tube condenser, also known as a heat exchanger, which is currently the most commonly used and best performing condenser in the oil industry. Can ensure that the cracked oil and gas fully cooled, high oil production. 5 safety device oil-water separator, water seal, vacuum device, to ensure the safe and efficient operation of equipment. The most commonly available fuel, carbon black, and non-condensable gases from the operating equipment are as follows: 1. Fuel oil : Mainly used in steel mills, boiler heating, heavy oil generating units, cement plants 2 carbon black: can be used for high-pressure ball combustion can also be used for refined toner. Refined carbon powder for new tires, rubber soles and pigments. 3. Non-condensable gas: The non-condensable gas generated during equipment operation is a combustible gas, which is generally recovered by the system and reused for heating the fuel in the reactor.
The China HSHCL 1500 ton concrete bridge launcher crane hydraulic is used to construct prefabricated spans up to 60m long. It is designed and fabricated in order to ensure high performances, efficiency, safety, flexibility and multiple successive utilization. Independent supports relocation system. Independent stressing platform handling system. Service overhead crane. Radio remote controls for all operations. Radio remote controlled spreader beam for segment positioning. Safety Features Safety is the most important issue for China HSHCL 1500 ton concrete bridge launcher crane hydraulic. To ensure the safety, the following safety devices are equipped in 1500 ton concrete bridge launcher crane hydraulic. Crane traveling limit switch. Overload protection device. Lifting height limit device. Voltage lower protection function . Phase sequence protection function. Emergency stop function. Rain cover for outside hoist, driving units, electric cubicle. Warning indicator : flashing nights and warning sounds. Wire-less infra-detector for anti-collusion. FAQ 1. Whatâ??s the information should I provide when inquiry about the China HSHCL 1500 ton concrete bridge launcher crane hydraulic? we need the Bridge Drawing, the Maximum longitudinal slope and the Maximum Transverse slope. The Girder/beam drawing. 2. How many kinds of construction methods for bridge launcher? 1. overhead segmental. 2. underslung segmental. 3. balanced cantilever erection segmental launching gantry. 4. full span. 3. What are inspection standard for load test of bridge launcher? a. Dynamic load test 1.1 times rated load, main girder does not down deflection, all mechanisms work well, performance parameters meet the design demand, all limit switches and safety protection interlock devices are reliable, all spare parts does not have cracking and flexible connection, all motors and contactors are not overheat. b. Static load test 1.25 times rated load, all mechanisms work well, the crane stops 20-30 min as trial load is lifted 10 cm high, then measure main girder down deflection(theodolite, ruler). Put down trial load to measure main girder upper camber, repeat 3 times, steel structure does not have permanent deformation; 4. How to make highway bridge concrete girders? Highway Bridge concrete girders could be made by 4 methods: Full span prefabrication. Segment girder prefabrication. Full span cast-in-place girder. Segment cast-in-situ. 5.How about maintenance of bridge launcher? a. Lubricating. b. Steel wire rope. c. Spreader. d. Pulley block. e. Wheels. f. Brake.
FGB Rod ends spherical bearings GE20DO GE20ES for Hydraulic Cylinder Knuckle joint bearing M: fgb003*fgbearing*com No.1 FGB Spherical Plain Bearings GE15ES Description: 1). Bearing Series: GE..ES; 2). Bearing Size: 15x26x12mm; 3). Sliding Contact Surface: Steel on Steel; 4). Relubrication Needed: With Lubrication; 5). Seals: Without Seals; No.2 FGB Spherical Plain Bearing GE15ES Design Features: 1). Outer ring with single split in axial direction; 2). Both outer and inner rings are phosphate treated; 3). But can be relubricated via annular groove and lubricating holes; No.3 We can supply other models of rod ends spherical bearing: GE6DO, GE8DO, GE10DO, GE12DO, GE15DO, GE16DO, GE17DO, GE17DO-2RS, GE20DO, GE20DO-2RS, GE25DO, GE25DO-2RS, GE30DO, GE30DO-2RS, GE35DO, GE35DO-2RS, GE40DO, GE40DO-2RS, GE45DO, GE45DO-2RS, GE50DO, GE50DO-2RS, GE60DO, GE60DO-2RS, GE70DO, GE70DO-2RS, GE80DO, GE80DO-2RS, GE90DO, GE90DO-2RS, GE100DO, GE100DO-2RS, FGB, GE110DO, GE110DO-2RS, GE120DO, GE120DO-2RS, GE140DO, GE140DO-2RS, GE160DO, GE160DO-2RS, GE180DO, GE180DO-2RS, GE200DO, GE200DO-2RS, GE220DO-2RS, GE240DO-2RS, GE260DO-2RS, GE280DO-2RS, GE300DO-2RS, GE320DO, GE340DO, GE360DO, GE380DO, GE400DO, GE420DO, GE440DO, GE460DO, GE480DO, GE500DO, GE530DO, GE560DO, GE600DO, GE630DO, GE670DO, GE710DO, GE750DO, GE800DO, GE850DO, GE900DO, GE950DO, GE1000DO GE4E, GE5E, GE6E, GE8E, GE10E, GE12E, GE15ES, GE15ES-2RS, GE17ES, GE17ES-2RS, GE20ES, GE20ES-2RS, GE25ES, GE25ES-2RS, GE30ES, GE30ES-2RS, GE35ES, GE35ES-2RS, GE40ES, GE40ES-2RS, FGB, GE45ES, GE45ES-2RS, GE50ES, GE50ES-2RS, GE60ES, GE60ES-2RS, GE70ES, GE70ES-2RS, GE80ES, GE80ES-2RS, GE90ES, FGBGE90ES-2RS, GE100ES, GE100ES-2RS, GE110ES, GE110ES-2RS, GE120ES, GE120ES-2RS, GE140ES, GE140ES-2RS, GE160ES, GE160ES-2RS, GE180ES, GE180ES-2RS, GE200ES, GE200ES-2RS, GE220ES-2RS, GE240ES-2RS, GE260ES-2RS, GE280ES-2RS, GE300ES-2RS FGB BEARING FGB SPHERICAL PLAIN BEARING FGB JOINT BEARING FGB ROD END BEARING FGB RADIAL SPHERICAL PLAIN BEARING FGB JOINT BALL BEARING FGB KNUCKLE JOINT BEARING FGB PLAIN BEARING
FGB Joint Bearing Radial Spherical sliding bearing GE80ES GE90ES Spherical Plain Bearing for Dry Cleaning machine No.1 FGB Joint Bearing GE80ES GE90ES Description: 1). Bearing Series: GE..ES; 2). Bearing Size: 80x120x55mm; 3). Sliding Contact Surface: Steel on Steel; 4). Relubrication Needed: With Lubrication; 5). Seals: Without Seals; No.2 FGB Joint Bearing GE80ES GE90ES Design Features: 1). Outer ring with single split in axial direction; 2). Both outer and inner rings are phosphate treated; 3). But can be relubricated via annular groove and lubricating holes; No.3 We can supply other FGB spherical plain bearing models: GEH4E, GEH5E, GEH6E, GEH8E, GEH10E, GEH12E, GEH15ES, GEH15ES-2RS, GEH17ES, GEH17ES-2RS, GEH20ES, GEH20ES-2RS, GEH25ES, GEH25ES-2RS, GEH30ES, GEH30ES-2RS, GEH35ES, GEH35ES-2RS, GEH40ES, GEH40ES-2RS, GEH45ES, GEH45ES-2RS, GEH50ES, GEH50ES-2RS, GEH60ES, GEH60ES-2RS, GEH70ES, GEH70ES-2RS, GEH80ES, GEH80ES-2RS, GEH90ES, GEH90ES-2RS, GEH100ES, GEH100ES-2RS, GEH110ES, GEH110ES-2RS, GEH120ES, GEH120ES-2RS, GEH140ES, GEH140ES-2RS, GEH160ES, GEH160ES-2RS, GEH180ES, GEH180ES-2RS, GEH200ES, GEH200ES-2RS, GEH220ES, GEH220ES-2RS, GEH240ES, GEH240ES-2RS, GEH260ES, GEH260ES-2RS, GEH280ES, GEH280ES-2RS, GEG4E, GEG5E, GEG6E, GEG8E, GEG10E, GEG12E, GEG15ES, GEG15ES-2RS, GEG17ES, GEG17ES-2RS, GEG20ES, GEG20ES-2RS, GEG25ES, GEG25ES-2RS, GEG30ES,FGB Bearing, GEG30ES-2RS, GEG35ES, GEG35ES-2RS, GEG40ES, GEG40ES-2RS, GEG45ES, GEG45ES-2RS, GEG50ES, GEG50ES-2RS, GEG60ES, GEG60ES-2RS, GEG70ES, GEG70ES-2RS, GEG80ES, GEG80ES-2RS, FGB Bearing, GEG90ES, GEG90ES-2RS, GEG100ES, GEG100ES-2RS, GEG110ES, GEG110ES-2RS, GEG120ES, GEG120ES-2RS, GEG140ES, GEG140ES-2RS, GEG160ES, GEG160ES-2RS, GEG180ES, GEG180ES-2RS, GEG200ES, GEG200ES-2RS, GEG220ES, GEG220ES-2RS, GEG240ES, GEG240ES-2RS, GEG260ES, GEG260ES-2RS, FGB Bearing FGB Spherical Plain Bearing FGB Rod End Bearing FGB Radial Spherical Plain Bearing FGB Joint Bearing FGB Knuckle Joint Bearing FGB Rod Ends Spherical Bearing
Main machine 1.Frame structure Full steel structure, stress released, with accuracy well kept. Main component is designed and Finite Element Analyzed through ANSYS software. Main frame composes of uprights, working table, holding-down beam and oil tank. Ball transporter and supporting bar and squaring arm are fixed on working table. 2.Upper blade beam and blades Guillotine type blade beam, with rake angle adjustable The rake angle could be motorized adjusted by press button according to material and thickness. When shearing thin thickness sheet, the rake angle could be reduced, thus the distortion of the product and the burr could be minimized. Exchangeable Rectangle blade, with 4 cutting edges available. Blade material 6CrW2Si with hardness HRC53-60, with quality shearing result and long life. 3. Shearing length/stroke adjustment The shearing stroke could be adjusted through knob to the length of the product. Thus efficiency could be improved. 4. Cutting beam guiding and blade clearance The cutting beam is guided between roller guides. At the rear of the cutting beam there are two sets of upper and lower roller guides located at each end of the beam. Two spring-loaded rollers located at the front of the shear apply pressure to the cutting beam, forcing it against the back roller guides. The bearings of the upper roller guides at the back of the cutting beam are mounted on an eccentric shaft. Rotating this shaft causes the cutting beam to tilt, thus providing proper blade clearance to the shearing blades. The upper cutting beam inclined forward, with high section-cutting quality on the product. The blades clearance could be adjusted manually through hand-wheel according to material and thickness. Since the blade clearance is 0.1 to 2.5 mm, the shear can cut thickness 1mm to 40mm mild steel. 5. Hydraulic system LVD special hydraulic unit for heavy type shear is adopted. Hydraulic control components is from VICKERS,USA (or REXROTH, Germany) With in-series cylinders to achieve good synchronization. The sheet is pressed by hold-down before shearing and during shearing for safety and reliability. One-time machining on CNC lathe for cylinder body and piston rod. Horning for inner surface of cylinder, vibration super-fine machining on the outer surface of the piston rod. Oil seals from NOK, Japan (or Merkel, Germany) with low wear and tear, no oil leakage. High-pressure internal gear pump, with reliability and low noise. Over-load protection for hydraulic system 6. Electrical system Movable remote operation station with emergency stop. Main electrical components(contactor, button and switch) adopt product from TELEMECANIQUE from France. Requirement on working condition: Working temperature: -10 to 47 Power supply: 380V±5%, 50HZ, 3 Phase
Introduction This machine used for laminating cardboard with A/B/C/D/E/F flute or single, double & triple wall corrugated board & 450-700g/m²Grey board. PLC control system and frequency converter adopt Schneider electrical,adjust the relevant parameters automatically according to the paper size .control is stable and accurate. Automatic feed top sheet and bottom sheet,and pneumatic correction mechanism is used for feeding top sheet, feeding bottom sheet adopts servo motor control. Equipped with automatic oil supply lubrication system. Type: Gluing Machine Condition: New Application: Apparel, Beverage, Chemical, Commodity, Food, Machinery & Hardware, Medical, Textiles Packaging Type: Film, Steel pallet,Wooden box,Export standard Packaging Material: Metal, Plastic, Wood Automatic Grade: Automatic Driven Type: Electric Voltage: 380v Power: 15-17kw Speed: 90m/min Max. sheet size: 1700*1100mm Place of Origin: Zhejiang, China (Mainland) Brand Name: GUDE Model Number: GFM-1300/1450/1700Z Dimension(L*W*H): 1420*222/237/262*268cm Weight: 7000/8000/9000kg Color:Up to you Certification: CE ISO9001 After-sales Service Provided: Engineers available to service machinery overseas Warranty: 1 year Name:Laminating Machine Function: Laminating cardboard with corrugated board & Grey board Max. sheet size:1700*1100mm Min. sheet size:400*400mm Thickness of top cardboard:200-450g/m² Thickness of bottom corrugated board: More than 500g/ã?¡,less than 7mm HS CODE: 8479899990 Packaging & Delivery Packaging Details: Export wooden box or steel pallet Delivery Detail: Shipped in 30 days after payment Payment T/T L/C Paypal Western Union Certification CE,ISO9001 Service Warranty: 1 year After-sales Service : Engineers available to service machinery overseas Machines are new (or unused) and the guarantee period will be given thirteen months from shipment date. During this period, the seller will offer free maintenance and free spare parts that caused by the machineâ??s quality, but the buyer must pay the courier cost. Parts damaged because of mishandling and consumable parts are not covered by any warranty. -
Single sided butyl tape, also known as composite type sealing tape, is a double layer composite sealing adhesive tape, one layer is self adhesive sealing tape, the other layer is butyl rubber, single sided butyl sealing tape composed by these two layers, and last covered with isolation paper and rolled into rolls. When using it, only need to tear up the isolation paper covering and winded use. It is popular used in steel structure factory building roof, metal roof patch and other construction projects cracks patch. Also suitable for sealing waterproof of pipe as well as fan with roofing lap joint, glass curtain wall, door and window sealing waterproof, etc. Specifications: Product name: single sided butyl tape. Material: butyl rubber and poly isobutene blending. Color: black, isolation paper can be yellow or white. Common width: 1 cm - 10 cm. Common thickness: 1 mm - 10 mm. Shelf life: twelve months. Service life: up to 20 years or more. Features: Excellent UV resistance. Simple construction, precise dosage. Easy to use: tear up the isolation paper. Without any solvents, safety and environmental friendly. Stable chemical properties: excellent chemical resistance, weather resistance and corrosion resistance. Butyl rubber material can keep permanent flexibility, good following nature and excellent waterproof sealing. Reliable application performance: its adhesion, waterproof, sealing, low temperature resistance are good, size stability. Excellent mechanical properties: bond strength, high tensile strength, good elasticity and elongation performance, strong adaptability to interface deformation and cracking. Applications: Single sided butyl sealing tape is mainly used for external anti-corrosion seal of steel pipeline in high voltage wire, cable joints, petroleum, drainage, pollution discharge, chemical and other industries. Packaging: Single sided butyl tape is packed with carton box. Carton size: 40 cm � 40 cm � 18 cm. Note: Transport: In the transport process, Single sided butyl tapes should be prevented from sun and rain, collision and extrusion packaging. Non dangerous goods transportation. Stacking layers of packing carton boxes should not be more than four. Storage: Single sided butyl tapes should be stored in a dry place with no more than 35°C, in order to avoid contact with the volatile solvent. Stacking layers of packing cartons should not be more than four.
Z03050900023AA Guardrails 644302499 Frame grease lubricated Casing Power Tong TQ340/35 Receiver TZS-K(JS) oil seal 5300200066 https://www.amlppmfg.com/sbr3570cc-02-upper-shear-ram-block.html ZQ203-125 oil drain line assembly 01.08.12.00M �?�¾�¼�¿�»�µ�º�? �¿�?�¾�º�»�°�´�º QF36001-02.17 FKQ8007 Anti-seismic pressure transmitter YPQ-250B ZQJ300*2-1.6*0.6 Desander Right Cyclone bracket pin DQ70BSD 9703642012 IA191-(P-059331-0000) Two-position three-way valve FQN24-10ZK ten-pin aviation plug (female) 78910-2 RTV,162 WHITE 10.3 OZ, C/W MSDS Rotary joint 4700650114 Driller Valve HD-2-X/P050973-1/IA295 Pneumatic control valve BK-F-W4 P981120140AA Channel steel L=514 SL450Flushing assembly SpacerII AA4501230905 Cable transport frame 1.16.07.01.001 Derrick cage\ZJ50 AQL.07.06 IA341Regulator FKQ6406-G steel ball seat 9160600007 Faucet SL450-5 collar 104.07.06.21 3.03.02.12.011 Electrical connector 2.4.34.074 connector QBJ10010302 NPT3/8"X1/4" bushing R431006327/P63985-1/7P-9S Rexroth valve Lubrication system F-1600HL oil filter assembly AH100101061000 Density meter level assembly XYM-5-1 XYM-5 density meter Impeller FMC15145ELA05 low pressure filter FKQ640-6DLQ-00-00 FKQ relief valve Y-25-20C Drain valve IA-193 Inner retaining ring DQ70BSD 9702020212 pin P2000669AA Manual pressure regulator ArCOO 0.05-0.85MPa safety slip WA-Csafety slip 13-1/2"~14-5/8" WA-C-011 Z04220200001AA Bolt, grommet retaining ring BK-7-7A9 FH4147 Impeller �° DSQ-01.00 4900300057 Water draining valve 70-30 High pressure plug valve 2"1502M*2"1502F/1 Disc brake emergency cylinder BG-00C CLUTCH ATD330H Hydraulic tubing pliers (power pliers) XQY-150/12 Nitriding block Q12.1 R431003807/P55556-4/8P-1S Rexroth valve filter element ZJ70D DLX9048 325Q10 Faucet SL125 flushing pipe assembly RI40391132-04 Power selection box 40-17 check valve oRing DQ70 2.4.51.031 Turntable ZJ-45 driller operation box 106.02.300.00 Boiler RL70 Boiler computer controller YLZK-C5 Bushing BKD-3-6D3 Frame plate liner insertF6041HS1A05 exhaust elbow 9Y2151 Vent 512604900000030801 Connector DQ70 3.03.03.04.001 gap adjuster9261914exhaust valve guide 197-6995 RADIATOR; Part Number: 5199000030; Gasket AH0801010203 Winch oil pump transmission shaft ZJ50D/3150 oil pump device (left-handed) AF400109-1201 Connector Assembly 154-5559filter element 9M2342 ZQ203-100 screw 16*20 FKQ12808BS relief valve Y-25,20C Dwyer 1910-1 Air Pressure Switch Gasket AH0801010415 Rubber Throat bush F6083R55 hydraulic valve\ZJ70D 4WEH16T50B/6EG24NEZ4 Pressure switch JDW 5 Inclinometer GE-MWD Probe upper end line plug 981992 air filter drain cup FKQ640-6 Well gauge YDTJ 140*2m Rubber mat EK140103-010131 4.10.09.009 Elastic washer Lubricator QYW-L15-S1 disc brake block JC-70B
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE :- BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray THINNER :- Type 290 POT LIFE :- 3 hours min at 30�° C RECOMMENDED DFT :- 30-40 �µ. OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Type 290 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Type 290 Addition : Max 5% Nozzle Orifice : 0.28- 0.37 mm Nozzle Pressure : 1400-1800 p.s.i.
7619066 WASHER, REG SPG LOCK 3/4 CD PL retaining block 2.3.04.003 Drill pipe clamp accessories ZQ203-100 Sliding sleeve 0106-05M 662010051 IMPELLER RETENTION BOLT 118844-22-22 Drill pipe tong accessories ZQ203-125 insert 19.100-01 111049-1 PIN, RETAINER (PAINTED YELLOW) Sleeve: Shot Pin For Tds Ps 11Sa 30151951 Lens F/Hyster Fork Lift 2027404 LW-0312-HS Hydraulic tank accessories F-1300 Double lip oil seal AH1301010406 REDUCING / RELIEVING VALVE 99353-1AN SEAL/GASKET, LINER 6.1/2 INCH - FOREIGN MADE--P/N:07923284 Power selection box accessories SNC40-17 console air circuit switch 56519-16-12-S ELBOW: 37�º O-RING BOSS E11236 Electromagnetic eddy current brake accessoriesZJ-45 control handle SK-1 Liner Stabilizer 30125012 INTERFACE ETHERNET 2 CHANNEL,MV3000 E15259 AY21504 Drill pipe tong accessories ZQ203-100 steel plate 0101-23AM Right bearing spacer p/n: P1103053AA Drill pipe clamp accessories ZQ203-125 Insert 19.100-01 Thermal Plotter ST820 Remote control system accessories YPD20/3 anti-backfire device TERMINAL ASSEMBLY 123294-3 30171518-1 SEAL, LINK TILT CYLINDER 56709-8-8-S ELBOW, STREET 45 VALVE CORE CONNECTING ROD FOR AIR PUMP FOR BOP CONTROL UNIT, BPM, P/N: 9163800027 Hydraulic tank accessories F-1600 cylinder head rod AH100101210100 LOWER IBOP ASSEMBLY 6205392/X 25XGZ-5K 6835322filter element 8152010 Electromagnetic eddy current brake accessoriesZJ-45 Electromagnetic brake fan GRT50 INBOARD LABYRINTH SEAL FOR DERRICK CENTRIFUGAL PUMPS â??P/N:G0006159 H19-1004-010 ZQ203-100 High pressure hose M30*1.5*10000 05-01M ND3128 Cooling Appliance*starter assembly PIN, OPERATING LEVER,ROTARY TABLE,ZP-375 ZP001.05 Hydraulic tank accessories F-1600 Wear disc removal tool 30182002-501 O-RING KIT, DEUBLIN Slotted nut M16 4.10.13.003 50006-7-C5D SCREW, CAP-HEX HD DRILLED PIN, ROLL, 0.19 X 0.63 LG, SST, 51603-05 FRICTION DISC W60-07-900 Drill pipe power tong accessories ZQ203-100/125 Cover 0104-12M Clutch Friction Disc Universal Dynamic Friction Disc 324WCB 508725 Hydraulic tank accessories F-1600 Oil supply oil pump YTX700 O-RING NOV, 51300-240-B Drill pipe clamp accessories ZQ203-100 Oil ring 0102-04M Petroleum Density Meter SY-1 0.81-0 Adapter 105mm 73mm 211 2 7/8"UPTBG male double positive VOLVOFM12 chassis*Steel plate center screw and cap INDUCTION MOTOR YBX3-160MI-2W FOR HH MUD PUMP BZ1000DBJ BLOWER MOTOR Power selection box accessories JR5232TSN air filter P200009984A Floating hoop FG ZX QZ 177.8mm TPCQ Buckle Cable : 3 Tsp X 1.0 Mm2 56627-03 190 series diesel engineFuel supply system * fuel injector assembly 12VB.16.00E Clutch assembly 115.35.00 99176+30 ISOLATOR,SAFETY,SINGLE-CHANNEL Valve spring AH100101-0529 109302-130NA FIXED-FLOW CONTROL VALVE VOLVOFM12 Universal*Headlight assembly
VOLVOFM12 startMachine * intercooler intake pipe clamp Electric control box FKDQ640-7 hand pneumatic pressure relief valve JYSQ21-25 Inclinator XXQ-178 178-310 transmission shaft 1.02.51.003 35-70 BOP AccessoriesFZ35-70 Ram rubber core 7-5/8" Seal: Oil F/Transmission Assy Ps-350/500 YS26001 Oil Filter, p/n LF 3625. FLEETGUARD for MERCEDES-BENZ model OM502LA engine. Material: synthetic canvas, steel 131100704 Oil seal with two lugs R01-FG dimensions 255x299x20 Drilling wire rope 6*19+FC left cross 6.2mm 1670 QUICK RELEASE VALVE, FOR DRAWWORKS, MODEL: JC70DB, MAKE: HONGHUA, P/N: KPJ-L15 AIR FILTER D-M42 FOR HPUYZ095.00 Drill pipe power tong accessories ZQ203-100 Right angle connector 0108.01-03M Wheel Loader AccessoriesWA380-3 starter motor 6743-82-6820 Drilling rig top drive accessoriesDQ40/50/70 roller SJ62 01.1.04 NB800G.05.13.00 Spring guide Plate:Clamp,Service Loop 78002 Drilling rig top drive accessoriesDQ40/50/70 flat steel wire cylindrical helical compression spring medium size 245*13*45 crank DQ70BSC 9703330011 �¦90-150/5 34JR6Y-L6 three-position four-way reversing valve for drilling rig special air control element Hydraulic tank accessories F-1600 O-ring 190*3.55G GB/T3452.1-1992 588-04-3 Drill pipe clamp accessories ZQ203-100 Upper sealing ring SHIM, ROTARY TABLE, ZP-375, NOV 10038013-001 LOCKWIRE Z6001-8 TEST FITTING, SAE-6 93024-6SAE 59124P230010 HOSE ASSEMBLY CONNECTING COLLECTOR; 23519348; DETROIT DIESEL; MIDDLE OUTLET PIPE Drill pipe clamp accessories ZQ203-100 pin 0101-39M Casing power tong accessories TQ35-13 3/8" jaw plate assembly 7" 56.620.00 PDC bit 152.4mm M1365 Power end accessories JR5231TSN OFM600 lubricating oil filter element P080001485 8864951P167 ARM,BEARING PE Bearing for 34ZS-21,25 Three position, four way valve-FOR BOP CONTROL UNIT, BPM Truck inner tube 1200in 20in Kunlun 50008-12-C5 SCREW, CAP-HEX HD (UNC) PIN-II PS80-03 FOR SAFETY CALIPER BRAKE ASSEMBLY, FOR DRAWWORKS, MODEL: JC70DB 35�?35 BOP accessoriesFZ35-35 dust ring DFZ5414-22 Pin : Spiral 51222-12-24 Electric control box FKQ640-6Accumulator rack 6PK.01.18-00 Liquid end accessories SEV5320TGJ TPH400 oil guide ring 4" Die support 203-216 1.03.09.046 GT550E variable speed* high and low speed hose 25YT-5J Explosion-proof plug-in Hydraulic tank accessories F-1000 Spacer Cylindrical roller bearings 234 PIN, CARRIAGE, GUIDE BEAM 123715 BRG, PLAIN, 9.00 x 9.187 x 0.75 M02-1041-010 hydraulic hose 2.4.21.080 Winch output shaft accessories ZJ32L6 shift mechanism BA70011-06.00 Detroit diesel engine parts crank linkage * crankshaft 16V149 5149096 Drill pipe clamp accessories ZQ203-100 Barometer connector assembly 010802-00M Swivel gooseneck SL225-02 for plug SL225 Casing power tong accessories TQ340-35Y washer 52.100-06 30173216-1 30171147-EX-2/39 Hydraulic tank accessories F-1600 Mud pump insurance valve piston Seven-pin plug/seat P28K4QJG/P28J4MQJG
Brief Introductions: Type: 14FF1 Bond: Metal Application: Carbide rolls Specification: Customized Brand Mark: Moresuperhard Trade Terms: FOB Packages: Hard carton Delivery Time: 15 workdays by express Introductions of Moresuperhardâ??s Metal diamond grinding wheels Diamond tipped bandsaw blade refers to a kind of diamond tools made by consolidating diamond particles on the sedimentary layer through electro crystallization of metal on the optimized annular base band by using a unique electrodeposition process. Electroplated diamond coated bandsaws are made from high quality steel with the leading edge coated with good quality diamond grit giving a continuous ribbon of aggressive cutting action on Silicon ingot ,GRP, glass reinforced plastics, carbon fiber, plastic composites and so on. Both straight cut and curves can be easily achieved, bearing in mind the tighter the curve required, the narrower width of bandsaw needed. Smallest cutable radius (mm) 16 40 65 95 145 185 305 Band Height (mm) 6 10 12 15 20 25 30 Detailed Specifications can be customized! Advantages of Moresuperhardâ??s Metal diamond grinding wheels Excellent cutting surface The highest level of precision at high cutting speeds and performance High efficiency: cutting hard alloy, marble, granite speed is dozens of times the efficiency of the traditional reciprocating saw or wire cutting machine High economic efficiency: because of its narrow incision (only 1.2mm-2mm), so less material consumption, less dust, low noise, cutting precious materials, especially has greater economic significance. Good cutting quality: the working part of the saw blade, that is, the thickness of the diamond blade is greater than the thickness of the matrix steel strip. With the help of the guide device, the saw blade does not contact with the surface, which is conducive to obtaining more stable sawing and higher processing quality. Especially for particularly difficult sawing carbon graphite and other materials, some materials bimetal saw blade saw not moving, alloy saw blade life is not long, the cutting surface is not smooth, for emery saw blade, is the best choice. Guide Recommended diamond size will vary depending on application. Primary factors to determine proper diamond size include: * Desired surface finish * Desired cutting speed * Cutting characteristics of material * Cutting width * Machine parameters Long chipping materials should be cut with coarser diamond size band saw blades. All diamond band saw blades are custom manufactured to fit your exact material, needs, and application requirements. We will work with you to determine your needs, and recommend the right parameters for your specific material / application. Service: Detailed Specifications can be customized! Provide after-sales service. Technical support on usage. Return and exchange of products for non-human reasons.
CKM Defense Road Blocker CKM Defense Hydraulic Road Blocker is the most widely used system in areas where entry and exit should be controlled and safe against all kinds of vehicle attacks, such as military facilities, government buildings, embassies, production facilities, oil refineries, hotels, airports, and stadiums. The system is specifically designed against vehicle impacts, and its components have been reinforced to be effective in all possible attack scenarios. Thanks to its hydraulic operating system, the CKM Defense Road Blocker System works continuously even in the busiest places. This system synchronizes with other security systems such as swing barriers, rising bollards, etc., keeping the defense at the highest level in case of attack, while allowing authorized vehicles to safely enter the area. It can be integrated with all kinds of Access Control Systems such as Plate Recognition Systems, HGS (Electronic Toll Collection-Fast Pass) Systems, Card Readers. TECHNICAL FEATURES Unit operating voltage: 380 VAC, 3-Phase, 50/60 Hz Length: 3111 mm, 4111 mm,5111 mm, 6111 mm �±20 mm Height above ground: 780 mm �± 10 mm The part buried under the ground: 1050 mm �±10 mm Width: 1350 mm �± 10 mm Color: Yellow Black Painted (RAL 1028, 9005) Collision unit: Steel Sheet and NPU NPI steel bar construction Wall thickness: 10 mm Surface coating: Electrostatic painted Corrosion coating: Shot blasting, epoxy under coating, electrostatic painted Turn On/Off Time: 4-6 sec. Emergency Take Off Feature: 2-3 sec. (optional) Turn On/Off Capacity: 1000 / day Power Engine: 4 kw or 5 kw , 380 V AC, 3-Phase Operating temperature range: -25 / 60 C Work System: Hydraulic system Hydraulic piston: 2 qty Hydraulic power unit: Industrial hydraulic pump, oil level and temperature gauge, manual hand pump Automation routing: 220 V two way solenoid valve Hydraulic pressure: 40-80 Bar Hydraulic tank: 30-50 liter Hydraulic hose: R2 3/8 330 Bar hose Hydraulic oil: 46 no. hydraulic oil Hydraulic system heating/cooling: Oil heater/cooler (optional) Control Cabinet: Cabinet Dimension: 900 x 900 x 700 mm (height, length, depth) Control System: Remote control,button control (optional), access systems (optional) Control Panel: Compatible with PLC base control, micro process control card, access systems devices (Access card, plate recognition system, finger print reader etc.) Manual Usage: Manuel hand pump, Warning Equipment: Warning light (optional), traffic lamp (optional), sound warning (optional) Protection System: Loop detector, photocell (optional) Drain pump: Optional concrete Infrastructure: C 35 concrete Power failure working status: Battery (optional)
Professional precise plastic product and mould  We can produce kinds of moulds and plastic products for customers as their special demand. Quotations will be based on drawings or samples provided by customers. Best quality and economic price,our products are guaranteed.  NameCustomized plastic productMaterialABS,PP,PE,PC,PVC,PS,PMMA,PA66+Fiberglass,rubber, siliconeRunnerHot/coldCavitySingle/multiDesign softwareUG, PROE, CAD, CAXA ect.Surface treatmentPolish,texture,sandblasting,chromeDelivery timeAccording to QuantitesPacakgeOPP Bag+Carton BoxSpecificationAccording to clients original sample or 3d drawingPackaging & Shipping Packing details of mold 1.Check mold component 2.Cleaning mold cavity/core and spread slushing oil on the mould 3.Cleaning  mold surface and spread slushing oil on the mould surface  4.Put mold into the wooden caseUnion MOULD SERVICE for mould makingIn-time response on letters, telephone calls or faxIn-time supply the mould designsIn-time communication on the technical pointsIn-time sending pictures for the mould machining progress and mould finishing  scheduleIn-time mould test and sample deliveryIn-time mould delivery.Mould one year guarantee,full life technique supportFAQ 1:Which kind information need for quotation  ? 1,Sample photo with size or 2D/3D design 2,Cavity quantity 3,Runner type, cold or hot 4,Mould steel type,P20, 718, 2738,H13,S136,2316,an so on. 5,Injection machine parameter or plate size(tie rod distance)   2:Delivery time in UNION MOULD 3~15 days for mould design, 15~60days for mould production after deposit payment and mould design confirmed   3:Payment Terms TT, L/C, Western Union, Paypal   4: Shipping Type By Air Or By Sea   5:Guarantee One year guarantee   6:Why choose Union MOULD? UNION Mould Factory is the leading plastic mould manufacturer in China,based on precise tooling, high technology and top mentality mould design.   Design We are professional for mould design,our technique absorbed from Taiwan and Europe. Quality All of our mould steel have certificate with longer mould life,mould produced by advanced equipment,the tolerance can reach +-0.01mm,the molded product have good appearance without any flash and good fit with other products. Price We always provide competitive price,because of we are manufacturer, we are the source Service Free product design&mould design 2D/3D Free sample delivery, 3 times mould test Every week update production informations. Mould one year quarantee,Mould full-life technique support Welcome
Professional precise plastic product and mould  We can produce kinds of moulds and plastic products for customers as their special demand. Quotations will be based on drawings or samples provided by customers. Best quality and economic price,our products are guaranteed.  NameCustomized plastic productMaterialABS,PP,PE,PC,PVC,PS,PMMA,PA66+Fiberglass,rubber, siliconeRunnerHot/coldCavitySingle/multiDesign softwareUG, PROE, CAD, CAXA ect.Surface treatmentPolish,texture,sandblasting,chromeDelivery timeAccording to QuantitesPacakgeOPP Bag+Carton BoxSpecificationAccording to clients original sample or 3d drawingPackaging & Shipping Packing details of mold 1.Check mold component 2.Cleaning mold cavity/core and spread slushing oil on the mould 3.Cleaning  mold surface and spread slushing oil on the mould surface  4.Put mold into the wooden caseUnion MOULD SERVICE for mould makingIn-time response on letters, telephone calls or faxIn-time supply the mould designsIn-time communication on the technical pointsIn-time sending pictures for the mould machining progress and mould finishing  scheduleIn-time mould test and sample deliveryIn-time mould delivery.Mould one year guarantee,full life technique supportFAQ 1:Which kind information need for quotation  ? 1,Sample photo with size or 2D/3D design 2,Cavity quantity 3,Runner type, cold or hot 4,Mould steel type,P20, 718, 2738,H13,S136,2316,an so on. 5,Injection machine parameter or plate size(tie rod distance)   2:Delivery time in UNION MOULD 3~15 days for mould design, 15~60days for mould production after deposit payment and mould design confirmed   3:Payment Terms TT, L/C, Western Union, Paypal   4: Shipping Type By Air Or By Sea   5:Guarantee One year guarantee   6:Why choose Union MOULD? UNION Mould Factory is the leading plastic mould manufacturer in China,based on precise tooling, high technology and top mentality mould design.   Design We are professional for mould design,our technique absorbed from Taiwan and Europe. Quality All of our mould steel have certificate with longer mould life,mould produced by advanced equipment,the tolerance can reach +-0.01mm,the molded product have good appearance without any flash and good fit with other products. Price We always provide competitive price,because of we are manufacturer, we are the source Service Free product design&mould design 2D/3D Free sample delivery, 3 times mould test Every week update production informations. Mould one year quarantee,Mould full-life technique supportÂ
Professional precise plastic product and mould  We can produce kinds of moulds and plastic products for customers as their special demand. Quotations will be based on drawings or samples provided by customers. Best quality and economic price, our products are guaranteed.  NameCustomized plastic productMaterialABS,PP,PE,PC,PVC,PS,PMMA,PA66+Fiberglass,rubber, siliconeRunnerHot/coldCavitySingle/multiDesign softwareUG, PROE, CAD, CAXA ect.Surface treatmentPolish,texture,sandblasting,chromeDelivery timeAccording to QuantitesPacakgeOPP Bag+Carton BoxSpecificationAccording to clients original sample or 3d drawingPackaging & Shipping Packing details of mold 1.Check mold component 2.Cleaning mold cavity/core and spread slushing oil on the mould 3.Cleaning  mold surface and spread slushing oil on the mould surface  4.Put mold into the wooden caseUnion MOULD SERVICE for mould makingIn-time response on letters, telephone calls or faxIn-time supply the mould designsIn-time communication on the technical pointsIn-time sending pictures for the mould machining progress and mould finishing  scheduleIn-time mould test and sample deliveryIn-time mould delivery.Mould one year guarantee,full life technique supportFAQ 1:Which kind information need for quotation  ? 1,Sample photo with size or 2D/3D design 2,Cavity quantity 3,Runner type, cold or hot 4,Mould steel type,P20, 718, 2738,H13,S136,2316,an so on. 5,Injection machine parameter or plate size(tie rod distance)   2:Delivery time in UNION MOULD 3~15 days for mould design, 15~60days for mould production after deposit payment and mould design confirmed   3:Payment Terms TT, L/C, Western Union, Paypal   4: Shipping Type By Air Or By Sea   5:Guarantee One year guarantee   6:Why choose Union MOULD? UNION Mould Factory is the leading plastic mould manufacturer in China,based on precise tooling, high technology and top mentality mould design.   Design We are professional for mould design,our technique absorbed from Taiwan and Europe. Quality All of our mould steel have certificate with longer mould life,mould produced by advanced equipment,the tolerance can reach +-0.01mm,the molded product have good appearance without any flash and good fit with other products. Price We always provide competitive price,because of we are manufacturer, we are the source Service Free product design&mould design 2D/3D Free sample delivery, 3 times mould test Every week update production informations. Mould one year quarantee,Mould full-life technique support
Professional precise plastic product and mould  We can produce kinds of moulds and plastic products for customers as their special demand. Quotations will be based on drawings or samples provided by customers. Best quality and economic price,Website:http://www.tzunionmould.net, our products are guaranteed.  NameCustomized plastic productMaterialABS,PP,PE,PC,PVC,PS,PMMA,PA66+Fiberglass,rubber, siliconeRunnerHot/coldCavitySingle/multiDesign softwareUG, PROE, CAD, CAXA ect.Surface treatmentPolish,texture,sandblasting,chromeDelivery timeAccording to QuantitesPacakgeOPP Bag+Carton BoxSpecificationAccording to clients original sample or 3d drawingPackaging & Shipping Packing details of mold 1.Check mold component 2.Cleaning mold cavity/core and spread slushing oil on the mould 3.Cleaning  mold surface and spread slushing oil on the mould surface  4.Put mold into the wooden caseUnion MOULD SERVICE for mould makingIn-time response on letters, telephone calls or faxIn-time supply the mould designsIn-time communication on the technical pointsIn-time sending pictures for the mould machining progress and mould finishing  scheduleIn-time mould test and sample deliveryIn-time mould delivery.Mould one year guarantee,full life technique supportFAQ 1:Which kind information need for quotation  ? 1,Sample photo with size or 2D/3D design 2,Cavity quantity 3,Runner type, cold or hot 4,Mould steel type,P20, 718, 2738,H13,S136,2316,an so on. 5,Injection machine parameter or plate size(tie rod distance)   2:Delivery time in UNION MOULD 3~15 days for mould design, 15~60days for mould production after deposit payment and mould design confirmed   3:Payment Terms TT, L/C, Western Union, Paypal   4: Shipping Type By Air Or By Sea   5:Guarantee One year guarantee   6:Why choose Union MOULD? UNION Mould Factory is the leading plastic mould manufacturer in China,based on precise tooling, high technology and top mentality mould design.   Design We are professional for mould design,our technique absorbed from Taiwan and Europe. Quality All of our mould steel have certificate with longer mould life,mould produced by advanced equipment,the tolerance can reach +-0.01mm,the molded product have good appearance without any flash and good fit with other products. Price We always provide competitive price,because of we are manufacturer, we are the source Service Free product design&mould design 2D/3D Free sample delivery, 3 times mould test Every week update production informations. Mould one year quarantee,Mould full-life technique support Welcome to contact
Professional precise plastic product and mould  We can produce kinds of moulds and plastic products for customers as their special demand. Quotations will be based on drawings or samples provided by customers. Best quality and economic price,, our products are guaranteed.  NameCustomized plastic productMaterialABS,PP,PE,PC,PVC,PS,PMMA,PA66+Fiberglass,rubber, siliconeRunnerHot/coldCavitySingle/multiDesign softwareUG, PROE, CAD, CAXA ect.Surface treatmentPolish,texture,sandblasting,chromeDelivery timeAccording to QuantitesPacakgeOPP Bag+Carton BoxSpecificationAccording to clients original sample or 3d drawingPackaging & Shipping Packing details of mold 1.Check mold component 2.Cleaning mold cavity/core and spread slushing oil on the mould 3.Cleaning  mold surface and spread slushing oil on the mould surface  4.Put mold into the wooden caseUnion MOULD SERVICE for mould makingIn-time response on letters, telephone calls or faxIn-time supply the mould designsIn-time communication on the technical pointsIn-time sending pictures for the mould machining progress and mould finishing  scheduleIn-time mould test and sample deliveryIn-time mould delivery.Mould one year guarantee,full life technique supportFAQ 1:Which kind information need for quotation  ? 1,Sample photo with size or 2D/3D design 2,Cavity quantity 3,Runner type, cold or hot 4,Mould steel type,P20, 718, 2738,H13,S136,2316,an so on. 5,Injection machine parameter or plate size(tie rod distance)   2:Delivery time in UNION MOULD 3~15 days for mould design, 15~60days for mould production after deposit payment and mould design confirmed   3:Payment Terms TT, L/C, Western Union, Paypal   4: Shipping Type By Air Or By Sea   5:Guarantee One year guarantee   6:Why choose Union MOULD? UNION Mould Factory is the leading plastic mould manufacturer in China,based on precise tooling, high technology and top mentality mould design.   Design We are professional for mould design,our technique absorbed from Taiwan and Europe. Quality All of our mould steel have certificate with longer mould life,mould produced by advanced equipment,the tolerance can reach +-0.01mm,the molded product have good appearance without any flash and good fit with other products. Price We always provide competitive price,because of we are manufacturer, we are the source Service Free product design&mould design 2D/3D Free sample delivery, 3 times mould test Every week update production informations. Mould one year quarantee,Mould full-life technique support Welcome to contact us: Contact:Ms vicky Mobile: +0086 137 3620 6058 Wechat/whatsapp : +0086 137 3620 6058 QQ: 2798299958 Skype:vicky.zhou.123