M6-M12 1 Container / Month
M6-M10 Currently Exporting to Europe. 1 Container / Month
We supply all categories of washers. Currently exporting 1 FLC every month.
Safety Insulin Syringe with Restractable Needle Safety Characteristics: after absorbing the expected dose of liquid medicine, if transportation is needed, push up the sliding-sleeve to protect the needle tip from physical damage during transportation; push the sliding sleeve to expose the needle tip before the injection starts, when the expected dose of liquid medicine is 100% injected, manually slide the sliding sleeve to the position where the connector base can no longer slide, the needle tip is completely covered in the sliding sleeve, and then the sliding sleeve is manually rotated until it is locked, it could effectively preventing repeated use and accidental needle sticking, and avoiding cross infection.
The Bard PerFix Light Plug is a medical device used in hernia repair. Bard is a well-known manufacturer of medical devices, and their hernia repair products include mesh implants designed to reinforce and support weakened or damaged tissue in the abdominal wall. Key features and considerations for the Bard PerFix Light Plug may include: Hernia Repair: The PerFix Light Plug is specifically designed for use in hernia repair procedures. Hernias occur when organs or tissues protrude through a weak spot in the surrounding muscle or connective tissue. Mesh Material: The product is likely made of a mesh material. Meshes used in hernia repair are often constructed from synthetic materials, such as polypropylene. Plug Design: The term "plug" suggests that the device is designed to fill or cover a defect in the abdominal wall associated with a hernia. Lightweight Design: The inclusion of "Light" in the product name may indicate that the mesh is designed to be lightweight while still providing effective support. Surgical Technique: The PerFix Light Plug is used by surgeons during hernia repair procedures to reinforce the tissue and reduce the risk of hernia recurrence.
We are supplier and exporter of Diesel. We have various types of Diesel. Petroalliance diesel fuel is the second distillate of crude oil. Ultra-low sulfur grades of D2, such as GOST 305-82, with a reduce sulfur content to a maximum of 0.02 percent and reduce sulfur pollution emissions. Diesel fuel is often used in diesel engines. Diesel engines or compression ignition engines, rely on the temperature increase of compression, rather than on spark plugs, to achieve reliable ignition timing and combustion efficiency.
NECH-DW-20 is a middle-sized double wing expadable container house with an area about 38 square meters. As a home use, it can accommodate 2 rooms, a toilet, a kitchen, and a living room; And it is also suitable for small-sized offices, conference rooms, or studios; You can freely design the layout of the room, the position of the doors, the style and size of the windows etc. Payment terms : TT
MPPT Solar charge controller Feature 1. We choose high speed and high performance 32-bit processor with excellent EMC design 2. Advanced MPPT tracking algorithm, the tracking efficiency more than 99% 3. High performance IGBT power module as electronic switch, there is no any mechanical switch, plus multiphase synchronous rectification technology, improves the stable greatly 4. Ultrafast maximum power point tracking speed to ensure tracking efficiency 5. Accurate identification and tracking of multi-peak maximum power points 6. With current-limiting charging function, charging current can be set, friendly and compatible with various capacity batteries. 7. Widely PV arraysâ?? voltage input, this can save the cost of PV combiner box, wires and construction 8. Full enclosed duct design and high-speed fan for cooling makes the controller suitable for various harsh environment 9. It shows the ambient temperature. It also has automatic temperature compensation function and RTC real time function 10. The perfect battery protection function and multi-stage charging improves battery life 11. It has the statistical function of generating capacity which is very convenient for customers to view the daily, monthly and total charging capacity of the controller. 12. Complete menu display and operation, plus the humanized design of browsing interface, these makes the operation more easy 13. It can work with GEL. LEAD-ACID, LITHIUM and other type battery 14. Twice protection function to protect battery from damage when the power switch is down (optional) 15. Standard Modbus communication protocol for RS-485 or GPRS communication to extend the communication distance (optional function)
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance. 2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection. 3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance and reduces the hidden cost of machine failure to repair. 4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set. 5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converter's usage, which reduced the cost of equipment investment, easy to connect wires and control. 6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load. 9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock. 10, Wide input voltage can be set according to customerâ??s requirement. Input voltage range can be selected from 100-300V, 200-500V or 500-850V, suitable for solar/wind system without backup batteries, it can save many cost and maximization use the solar/wind energy. 11, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%. 12, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance. 13, European CE (EMC, LVD, UL1741) and ISO9001 certificates. [Optional] A, RS485 communication; B, AC bypass complementary function; C, Built-in charger
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stationsâ?? need, there are 48Vã??96Vã??120Vã??192Vã??220Vã??240Vã?? 360Vã??384Vã??480Vã??492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V 192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance. 2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection. 3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance and reduces the hidden cost of machine failure to repair. 4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set. 5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converterâ??s usage, which reduced the cost of equipment investment, easy to connect wires and control. 6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load. 9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock. 10, Wide input voltage can be set according to customer's requirement. Input voltage range can be selected from 100-300V, 200-500V or 500-850V, suitable for solar/wind system without backup batteries, it can save many cost and maximization use the solar/wind energy. 11, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%. 12, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance. 13, European CE (EMC, LVD, UL1741) and ISO9001 certificates. [Optional] A, RS485 communication; B, AC bypass complementary function; C, Built-in charger
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
We choose high speed and high performance 32-bit processor with excellent EMC design Advanced MPPT tracking algorithm, the tracking efficiency more than 99% High performance IGBT power module as electronic switch, there is no any mechanical switch, plus multiphase synchronous rectification technology, improves the stable greatly Ultrafast maximum power point tracking speed to ensure tracking efficiency Accurate identification and tracking of multi-peak maximum power points With current-limiting charging function, charging current can be set, friendly and compatible with various capacity batteries. Widely PV arrays voltage input, this can save the cost of PV combiner box, wires and construction Full enclosed duct design and high-speed fan for cooling makes the controller suitable for various harsh environment It shows the ambient temperature. It also has automatic temperature compensation function and RTC real time function The perfect battery protection function and multi-stage charging improves battery life It has the statistical function of generating capacity which is very convenient for customers to view the daily, monthly and total charging capacity of the controller. Complete menu display and operation, plus the humanized design of browsing interface, these makes the operation more easy It can work with GEL. LEAD-ACID, LITHIUM and other type battery Twice protection function to protect battery from damage when the power switch is down (optional) Standard Modbus communication protocol for RS-485 or GPRS communication to extend the communication distance (optional function)