Aviation Jet Fuel is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colourless to straw coloured in appearance. The most commonly used fuels for commercial aviation are Jet A and Jet A1, which are produced to a standardised international specification. The only other jet fuel commonly used in civilian turbine-engine powered aviation is Jet B, which is used for its enhanced cold-weather performance. Jet fuel is a mixture of a variety of hydrocarbons. Because the exact composition of jet fuel varies widely based on petroleum source, it is impossible to define jet fuel as a ratio of specific hydrocarbons. Jet fuel is therefore defined as a performance specification rather than a chemical compound. Aviation Jet Fuel is commonly referred to as JP54. However, this is the wrong terminology as there is no such grade of Jet Fuel. Jet A and Jet A1 are what refineries offer. Aviation Jet fuel Gas is what powers turbine aircraft engines. Worldwide, Jet Fuel is the most used low Sulphur content Kerosene. For instance, Colonial JP54 is similar to Jet A except the energy is 18.4 mj/Kg compared to the 42.8 MJ/kg of Jet A. Most importantly there is also a slight difference in additives. Aviation Jet Fuel B is used for its extremely cold weather performance. However, aviation Jet fuel Bs lighter composition makes it more dangerous to handle. For this reason, it is rarely used except in very cold climates. A blend of approximately 30% Kerosene and 70% Gasoline. Because of its very low freezing point (60 C (76 F), it is known as a wide cut fuel and has a low flash point as well. Aviation Jet Fuel B is primarily used in some military aircraft. In Canada, it is also used because of its freezing point. Aviation Kerosene standards are published as GOST10227-86. The standard consists of different properties. It separates paraffin and gasoline in the refinery. Military organisations around the world use a different classification system of JP (for Jet Propellant) numbers. Some are almost identical to their civilian counterparts and differ only by the amounts of a few additives. For instance, Jet A1 is similar to JP 8, Jet B is similar to JP 4. Military fuels are highly specialised products and are developed for very specific applications. Jet fuels are sometimes classified as kerosene or naphtha type. Kerosene type fuels include Jet A, Jet A1, JP 5 and JP 8. Naphthatype jet fuels, sometimes referred to as wide cut Jet Fuel, including Jet B and JP 4.
Aviation Jet Fuel is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colourless to straw coloured in appearance. The most commonly used fuels for commercial aviation are Jet A and Jet A1, which are produced to a standardised international specification. The only other jet fuel commonly used in civilian turbine-engine powered aviation is Jet B, which is used for its enhanced cold-weather performance. Jet fuel is a mixture of a variety of hydrocarbons. Because the exact composition of jet fuel varies widely based on petroleum source, it is impossible to define jet fuel as a ratio of specific hydrocarbons. Jet fuel is therefore defined as a performance specification rather than a chemical compound. Aviation Jet Fuel is commonly referred to as JP54. However, this is the wrong terminology as there is no such grade of Jet Fuel. Jet A and Jet A1 are what refineries offer. Aviation Jet fuel Gas is what powers turbine aircraft engines. Worldwide, Jet Fuel is the most used low Sulphur content Kerosene. For instance, Colonial JP54 is similar to Jet A except the energy is 18.4 mj/Kg compared to the 42.8 MJ/kg of Jet A. Most importantly there is also a slight difference in additives. Aviation Jet Fuel B is used for its extremely cold weather performance. However, aviation Jet fuel Bs lighter composition makes it more dangerous to handle. For this reason, it is rarely used except in very cold climates. A blend of approximately 30% Kerosene and 70% Gasoline. Because of its very low freezing point (60 C (76 F), it is known as a wide cut fuel and has a low flash point as well. Aviation Jet Fuel B is primarily used in some military aircraft. In Canada, it is also used because of its freezing point. Aviation Kerosene standards are published as GOST10227-86. The standard consists of different properties. It separates paraffin and gasoline in the refinery. Military organisations around the world use a different classification system of JP (for Jet Propellant) numbers. Some are almost identical to their civilian counterparts and differ only by the amounts of a few additives. For instance, Jet A1 is similar to JP 8, Jet B is similar to JP 4. Military fuels are highly specialised products and are developed for very specific applications. Jet fuels are sometimes classified as kerosene or naphtha type. Kerosene type fuels include Jet A, Jet A1, JP 5 and JP 8. Naphthatype jet fuels, sometimes referred to as wide cut Jet Fuel, including Jet B and JP 4.
D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.
product Description : These Products are Exported with Stringent Adherence to Standard Russian Export Specifications with Respective GOST. Price of product ( USD price or FOB price) : Product will be priced in USD$ Based on an Appropriate PLATTS INDEX or a FIXED Price and the Agreed Upon Shipping Method. The Price will be Mutually Agreed to by Buyer and Seller Product origin : Russian Federation Key Specifications/Delivery/Logistics : 1. Certification SGC or Equivalent 2. Payment Terms = Letter of Credit ( Details to be agreed upon by Buyer and Seller 3. Delivery Time = Varies by Destination 4. Port of Loading = TBD Minimum Order Size & Contract Term : Minimum Monthly Quantity = 100,000 MT X 12 Month Contract Required with R & E up to 120 Months
Jet fuel in the price $-negotiable discount from Platt NWE ARA. The seller deals with non-Sanctioned sources and has multiple refineries and the buyer will be signing the contract with the seller who is the title holder!
TECHNICAL SPECIFICATION DATA SHEET: PROPERTY TEST ASTM TEST METHOD API @ 60 F 30- 45 ASTM D-1298 Sulfur (wt%) max 0.8 ASTM D-4294 BS &W % max 2.0 Paraffins (vol. %) 40 -70 ASTM D-2789M Naphthenes (vol. %) > 25 ASTM D-2789M Organic Chloride(ppm) < 1.0 ASTM D-4929 Organic Nitrogen max (ppm) 500 ASTM D-4629 Microcarbon Residue (MCRT) 2.0 Max ASTM D-4530 Light ends C2 â?? iC5 5 % Max Total Acid Number, mg KOH 0.8 ASTM D-664 Metals by ICP ASTM D-5708 Vanadium
BASE Oil-SN 60, 70, 150, 300, 500, 600, 650 & BS 150.
Used Engine Oil
Technical specifications: 1) Free fatty acid: 1-3% 2) Free fatty acid: 3-5% 3) Free fatty acid: 5-10% 4) Free fatty acid: 10-20%
Technical Data Sheet Property Average Value Gravity@15.6oc : 0.859 Max SPI: 33.45 Sulphur: 1.2-1.5 Max Water & Sediment Content: 0.2 Max Water Content: 0.1 Max Salt Content: 8 Max Carbon Residue: 4 Max Reid Vapour Pressure: 0 Pour Point: 0.35 Ash: 0 Asphalt : 1 Max ASTM Stabilized Gravity: Degree 3.7 Recovery @50oc: 0.8 Min @100oc: 8 @200oc: 28 @250oc: 37 @300oc: 47 Total Distillate: 47 Total Residue: 2.5Max
MOQ: 10,000 Barrels per Month Supply Ability: 1,000,000 Barrels per Month JP54 Technical Specifications: ADDITIVES Antioxidant in hydro processed fuel mg/l min 17 max 24 Antioxidant non hydro processed fuel mg/l max 24 Static dissipater first doping ASA- 3 mg/l max 1 Stadis 450 mg/l max 3 COMBUSTION PROPERTIES Specific energy, net mi/kg min 18.4 D 4808 Smoke point mm min 19 D 1322 Lumininomitter number min 45 D 1740 Naphtales % vol max 3 D 1840 Propriety unit min max result test ip method ASTM COMPOSITION Total acidity mg KOH /g max 0.01 354 D 3242 Aromatic % vol max 22.0 158 D 1318 Sulphur, total % mass max 0.30 107 D 1266/2622 Sulphur mercaptan % mass max 0.003 342 D 3227 Doctor test 30 D 4952 VOLATILITY Initial boiling point centigrade max report 123 D 96 10% vol at C 240 20% vol at C report 50% vol at C report 80% vol at C report End point centigrade max 42 170/303 D 56 / 3828 Density at 15 C kg m2 min /max 776/840 180/385 D 1298 LOW TEMPERATURES PROPERTIES freezing point centigrade max 40 15 D 1298 Corrosion copper (2hrs at 100 C) Corrosion silver (4 hrs at 500C) max 1 227 STABILITY Thermal stability control temp. 280C 323 Filter pressure, differential mm. Hg max 25 Tube deposit rating (visual) max
Base oil sn60, 70, 100, 150, 350, 400, 500, 550, 600, 650; jet fuel a1, jp54, crude oil, bitumen 50,60/70, 90/100 & all grades of bitumen, used cooking oil, transformer oil, industrial oil, all types of grease, lng/lpg, used motor or engine oil, all types of motor oil, lubricants, additives and types of petroleum products.
Frozen fishes and shrimps , frozen halal meat , en 590 10 ppm & jet fuel a1, icumsa sugar 45, hms 1&2 iron scrap and used rails , aluminium ingot , copper cathode and millberry , frozen and fresh seafood, meat and frozen french fries.Export
ACCU CHEK ACTIVE TEST STRIPS - 50 per BOX MOQ: 10,000 per Month Supply Ability: 250,000 Boxes Monthly Payment terms: 100% Pre-payment by wire TT Delivery time: 30 days
ACCU CHEK ACTIVE TEST STRIPS - 50 per BOX ACCU CHEK ACTIVE TEST STRIPS - 50 per BOX ACCU CHEK ACTIVE TEST STRIPS - 50 per BOX
UniGold HIV 1/2 Test Kits UniGold HIV 1/2 Test Kits UniGold HIV 1/2 Test Kits
Clear View Complete HIV Clear View Complete HIV Clear View Complete HIV
BD Contact-Activated Lancet 21g X 1.8mm Depth (Pink)200/BX