V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5
Innovation not only brings convenience to professionals, but with more surprises. Now our new product SY-E 1:1 Contra Angle handpieces with Push Button have been using in dental offices. Every clinician finds it convenient and flexible to their diversified needs. SY-E 1:1 Contra Angle handpieces with Push Button are NSK compatible and work perfectly with least vibration. As it is directly from our own OEM division ASPIRELABS, you can find the lowest possible price, It also weighs less than most others and some other features are below for your reference. The following is other tech information. Features: Body size£ºØ 7.6 * H 13.35 Bur size£ºØ 2.35 (CA bur) Chuck£ºpush button Ratio£º1:1 Air pressure£º0.3MPa Rotate speed£º18,000 ¨C 25,000 r.p.m.
Traditional fiber optic handpiece cannot work without wire. Now our revolutionary new product E-Generator Fiber Optic Handpiece brings light without wire. This Handpiece has an internal Air-Driven Generator, which supplies fiber optic to light the tip of the handpiece. NEW SY E-Generator Fiber Optic Handpiece high performance 25,000 LUX. It also offers triple water spray. Improving visibility and cooling where you need it. 1. Super torque, standard head, mini head 2. 2 Hole/ 4 holes 3. Triple water spray 4. Fibre optic handpice with Air-driven generator inside; 5. Push button 6. Ceramic bearing 7. Noise Level: less than 70dB 8. Net weight: 88g 9. Torque Head Height 12.55 mm 10. Torque Head Diameter 14.4 mm 11. Air Pressure: 250-300Kpa 12. Rotation Speed: 310,000-350,000 RPM. Please contact us through SYdentistry website directly; we will get back to you within 24 hours.
Product Description Texol Gear Oil SAE 75W90 API GL-5 is a fully synthetic Gear Oil from synthetic base stocks and advanced additives. These additives provide protection from wear, rust and oxidation. The extreme pressure additives based on Sulphur and Phosphorus chemistry resist high and shock loads. Applications Texol Gear Oil SAE 75W90 API GL-5 recommended for heavily loaded and non synchronized transmissions and hypoid in passenger cars and other automotive equipment operat-ed under high-speed, shock- load; high-speed, low-torque; and low-speed, high-torque conditions. Features and Benefits Provides long life of manual transmissions gears. Excellent anti-wear and anti-rust protection. Minimal environmental degradation as the oil is free from Lead based additives. Excellent load carrying. Specifications and Approvals API: GL-5 ZF TE-ML 07A Health and Safety Detailed health and safety information for this product is provided in a Material Safety Data Sheet which is available upon request from our Texol sales office.
J series of 201 stainless steel | J1, J2, J3, J4, J5 J1: The carbon content is slightly higher than J4, and the copper content is lower than J4. Its processing performance is not as good as J4 material. It is suitable for ordinary shallow deep drawing and large angle deep drawing products such as decorative panels, bathroom products, sinks, and product pipes. J2, J5: Decorative tubes are easy to process, high hardness (both above 96�°), polished and beautiful, but they are easy to burst when used for square tubes or curved tubes (90�°). In terms of flat panel, due to its high hardness, the surface of the panel is more beautiful, and surface treatment such as frosting, polishing, and color plating can be carried out. But the biggest problem is bending, bending is easy to break, planing is easy to burst, so the ductility is not good. J3: High carbon, low chromium and low copper, but because of its high carbon content and low copper content, the material is slightly harder, so it is not suitable for bending with a slightly stronger strength. Compared with 201 stainless steel J1 material, the ductility is not so good, and it is easier to rust in the same environment. 201 stainless steel coil In the field of narrow bands, the emergence of 201 stainless steel J3 can better meet the requirements of pipe manufacturers for corrosion resistance and deformation. Because it can reduce the cost of raw materials for pipe manufacturers, it is sought after by pipe manufacturers in the narrowband field. J3 material is easy to process in veneer, but not difficult. The master of the processing factory said that he used J3 material to bend the board, and there would be an inner seam after it was broken (for black titanium, color board series, sanding board, when it is broken apart, there will be an inner seam when folding). The material of the sink has been bent 90 degrees, and it will not work if it continues. J4: The material of J4 is a relatively high-end variety in the J series of 201 stainless steel. It is suitable for deep drawing products with small angles. Most of the products that need deep drawing and salt spray test will choose it. Such as sinks, kitchen utensils, bathroom products, kettles, thermos cups, door hinges, pots, etc.
Product Description Texol ATF Dex VI is a new generation, Premium class, fully synthetic, multi-vehicle ATF suitable for current and all previous types of vehicles needing Dexron type Transmission fluids. The product is made using fully synthetic base oils and carefully selected friction modifiers, anti-wear additives, viscosity index improvers and oxidation inhibitors. Synthetic base oil provides high viscosity index and high operating range besides providing very low pour point. Applications Texol ATF Dex VI is a multi-vehicle ATF recommended for almost all the latest automatic transmissions needing Dexron VI and Mercon LV fluids. It is suitable for Voith, BMW and ZF transmission oils such as 5 speed, 6 speed, 7 speed, 8 speed and 9 speed gear boxes (Lifeguard), besides applications requiring JASO 1A oil. Texol ATF Dex VI is recommended for use in Allison C3, C4 applications, Chrysler ATF +3 and +4; ATF 134, T-IV, Type WS, Mopar 8&9, SP-IV, LT 71141, 3309, 3403, etc. Features and Benefits Good viscosity/temperature characteristics. High thermal stability. Very good low temperature properties. High stability to aging and high chemical resistance. Resistance to wear and good friction characteristics. Excellent corrosion protection. Quality, Specifications and Approvals GM DEX VI JASO 1A Texol's proprietary specifications. Health and Safety Detailed health and safety information for this product is provided in a Material Safety Data Sheet which is available upon request from our Texol sales office.
Hotmelt Adhesive for Book Binding Description Book Binding Glues are suitable for all kind of high speed Perfect Book Binding machines like Muller Martini, Kolbus, Welbound, Wholenberg etc. Adhesives show good performance on coated paper / art paper. They may also be used for other paper-to-paper bonding applications. Advantages: 1. Free flowing characteristics of melt, good machinability & spreading. 2. Flexible, higher coverage, strong bonding. 3. Low odor / fumes during usage. 4. Binding characteristics: Not affected by extreme hot or cold environments. Spine maintains its flexiblity.
Our high speed dental handpiece bearings mainly have two specifications, 3.175*6.35*2.38mm and 3.175*6.35*2.78mm. The rmp can reach 350000~400000. The material of bearings: all stainless steel; stainless steel rings with ceramic balls. The designs available: smooth, flanged, grooved. The mail item nos are SR144TL, SR144TLZ, SR144TLZ1, SR144K1TLZ, SR144K2TLZ, SFR144TL, SFR144TLZ, SFR144TLZ1, SFR144K1TLZ, SFR144K2TLZ, SR144TLK, SR144TLKZ, SR144TLKZ1, SR144K1TLKZ, SR144K2TLKZ, SR144TLW, SR144TLZW, SR144TLZ1W, SR144K1TLZW, SR144K2TLZW, SFR144TLW, SFR144TLZW, SFR144TLZ1W, SFR144TLGZW, SFR144TLGZ1W, SFR144K1TLZW, SFR144K2TLZW, SFFR144TLW, SFFR144TLZW, SFFR144TLZ1W, SR144K1TLKZW, SR144K2TLKZW. We are high speed dental bearings manufacturer in China.
In the complex and demanding world of oil and gas exploration, drilling bentonite emerges as an indispensable ally. This natural clay, enriched with montmorillonite, offers unmatched properties that enhance drilling efficiency, ensure environmental safety, and reduce operation costs. Our premium drilling bentonite is engineered to meet the rigorous demands of the drilling industry, delivering performance that surpasses conventional drilling fluids. What is Drilling Bentonite? Drilling bentonite is a specialized form of bentonite clay that has been optimized for use in drilling operations. Sourced from high-quality deposits, our bentonite undergoes a meticulous process of extraction and refinement to ensure it delivers superior performance. Primarily composed of montmorillonite, our drilling bentonite features a unique combination of minerals that contribute to its exceptional swelling, sealing, and stabilizing properties. Chemical and Physical Properties The excellence of drilling bentonite lies in its chemical composition and physical attributes. With a formula of Al2H2Na2O13Si4, it showcases a robust structure ideal for drilling applications. It possesses a high swelling capacity which allows it to expand and form a gel-like consistency when mixed with water. This characteristic ensures the formation of a thick filter cake that effectively seals the boreholes, preventing fluid loss and stabilizing the wellbore. Superior Drilling Efficiency Our drilling bentonite enhances the efficiency of drilling operations by offering superior lubrication, exceptional fluid loss control, and effective cuttings removal. Its rheological properties ensure that the drilling fluid maintains a low viscosity at high flow rates, improving the removal of cuttings and reducing the risk of borehole instability. Furthermore, its high yield point increases the carrying capacity of the fluid, allowing for the suspension and transport of larger quantities of cuttings at lower pump pressures. Applications in Various Drilling Scenarios Our drilling bentonite is versatile and can be adapted to various drilling scenarios, including: Vertical Drilling: Enhances drilling speed and efficiency while maintaining borehole stability. Horizontal and Directional Drilling: Provides superior rheological properties that ensure the smooth steering of the drill bit through complex geological formations. High-Pressure High-Temperature (HPHT) Wells: Resists thermal degradation and maintains its sealing and lubricating properties under extreme conditions.
Product Description Texol Super Duty Plus SAE 15W40 API CI-4 is a heavy-duty multi-grade diesel engine oil for use in high speed diesel engines; specifically formulated for on-highway and off-highway applications. It complies with the low emission law especially Exhaust Gas Recirculation (EGR) systems. Applications This oil is recommended for use in naturally aspirated and turbo-charged diesel-powered equipment from leading Japanese, European and American Manufacturers, mixed fleets, On-highway light and heavy-duty trucking, off highway industries including construction, mining, quarrying and agriculture. The oil is backward compatible with other API Diesel classes like API CH-4, CG-4, CF-4, CD, etc. Features and Benefits Exceptional Thermal and Oxidation Stability ensures trouble-free operation. Reduced maintenance costs due to minimized engine overhaul periods. Advanced detergency/dispersancy leading to cleaner engines and longer component life. Stay in grade shear stability provides wear protection and viscosity control. Designed for use with fuels with Sulphur of 5,000 ppm. Engine durability where EGR is provided. Specifications and Approvals ACEA E-7 (2016) API CI-4 (Approved by API) API CH-4 / API CG-4 / API CF-4 / API CF / API SL / API SJ Caterpillar ECF-2 / ECF-1-a Cummins CES 20078 / 200777 / 20076 Detroit Diesel DDC 93K215 Global DHD-1 Mack EO-N / EO-M+ MAN M 3275 / 271 MB 228.3 / 228.1 MTU Type 2.0 / 1.0 Renaut RLD-2 Volvo VDS-3 / VDS (Volvo approved) Deutz DQC III-10 Health and Safety Detailed health and safety information for this product is provided in a Material Safety Data Sheet which is available upon request from our Texol sales office.
Hindalco's closure stock is rolled to very fine tolerances to yield more closure per tonne of stock and to allow uninterrupted operation of high-speed, multiple-cavity presses. Its strength, high formability, low earring and printable surfaces make it ideal for pilfer-proof caps and vial seals. Packing Sheet: Sheets are placed in wooden boxes on wooden skids with runners along the length of the sheet. They are wrapped in HDPE with a hardboard on top and bottom of the stack. Hoop iron strapping runs along the length of the sheets. Silica gel packets are put in the boxes for moisture protection. Alternatively, they are wrapped in a poly-laminated gunny or polythene, strapped with a hoop iron strap and clip and placed on a wooden pallet. Edge guards are used and the sheets are wrapped with protective thermocol sheets. Coil: Coil is placed on wooden pallets in either eye-to-sky or eye-to-wall condition, wrapped in HDPE fabric and hardboard, and strapped with hoop iron. Silica gel packets are used for moisture protection. Applications : Pilfer-proof caps Vial seals Cream containers and caps
-function music player/power show/remote control/phone/USB bluetooth link the plug/MP3 / forward/backward/high/low speed can be adjust the volume before and after a key to add and subtract/start/intelligent functions such as slow, double drive 550 big motor, powerful, with independent braking, steering motor, 380 one-to-one 2.4 G wireless remote control liberates child's hands, Three-point seat belt, comfortable oversized backrest, dazzling lights, dynamic music, 12V7AH battery, wheels with PVC silent wheel bar, the body comes with 5 gears length adjustment, 1-3 gears for ch
Wholesale Passenger Car PCR Tyre, 4WD Offroad SUV 4X4 at/Mt Mud Tyres, Truck tires, tractor, excavator Sizes: 12.00R20 Type Inner Tube Structure All-steel radial Position steer/all position Application Off road Features: Wider tread, High speed, low rolling resistance, excellent wet grip etc. Place of Origin China Loading Port Qingdao Certificates: ECE, etc. OEM Yes Supply Ability: 7 million pieces per Year Min. Order: 1*20 GP HS Code: 40112000 Technology: German Technology Quality warranty: 120000� km Shipment Date: Within 15 days after deposit Package: Standard package for exporting Supplier Star Rating: Top five stars
New TLC E-Generator Fiber Optic Hand piece Traditional fiber optic hand piece cannot work without wire. Now our revolutionary new product TLC E-Generator Fiber Optic Hand piece brings light without wire. This Hand piece has an internal Air-Driven Generator, which supplies fiber optic to light the tip of the hand piece. New TLC E-Generator Fiber Optic Hand piece high performance 25,000 LUX. It also offers triple water spray. Improving visibility and cooling where you need it. 1. Super torque, standard head, mini head 2. 2 Hole/ 4 holes 3. Triple water spray 4. Fibre optic handpice with Air-driven generator inside; 5. Push button 6. Ceramic bearing 7. Noise Level: less than 70dB 8. Net weight: 88g 9. Torque head height 12.55 mm 10. Torque head diameter 14.4 mm 11. Air pressure: 250-300kpa 12. Rotation speed: 310, 000-350, 000 RPM
Dental hand piece come in either without light on the tip of the hand piece, or with light. The type that comes with light is usually powered by the fiber optic source which requires significant investment in the matching dental chair and the related fiber optic system. Now our revolutionary new product TLC E-Generator hand piece brings light to dental offices that have been using hand pieces that do not have the light on the tip. TLC E-Generator has an internal power motor that is air driven, which supplies LED lighting to the tip of the hand piece, so dental professionals can view the operation area without outside light. In fact this TLC lighting system is even more focused and bright than most fiber optic systems. And not the least, the pricing, as it is directly from our own OEM division, sells even lower than most other regular high speed 4 hole hand pieces. It also weighs less than most others and some other features are below for your reference. 1. Self-sufficient power system instead of external light source. Self-illuminated, natural light 2. Operating air pressure: 0.25-0.3Mpa (0.3MPa preferred) 3. Air consumption: 55L/min 4. Speed of generator: 25,000-30,000 R.P.M 5. 420,000 r.p.m for standard head 6. Ceramic Bearings: Quieter and longer life 7. Ultra Push Chuck: Simple bur exchange 8. 3-hole water spray 9. Sterilization by autoclave at (135) Centigrade 10. Unenclosed Cartridge 11. Noise level: Less than 68 dB 12. Chucking power: 20-45N 13. Net weight: 88g 14. Ergo Grip: Secure Grip for your confidence 15. ISO 7785-1 16. CE Mark 0197 17. One year guarantee (half year for bearings)
Full function. Lateral drifting tyres. Die cast body. 4 Wheel Drive. Shock Absorber. Vehcle size: 48x30x25CM USB charging cable. Charging time: 4 hours. R/C distance: 30 - 35 Meters. Operation time: 15 - 20 minutes. Speed: 10 - 15 KMH Climbing angle: 15 degrees. 4 colors available: blue, orange, red, green. Age grade: 8+