Turbidity ASTM D 4176 Less Than 2,0 Density at 15 C Kg/1 ASTM D 1298 & D 4052 0,8200-0,8800 Density at 20 C Kg/1 ASTM D 1298 & D 4052 0,8064-0,8766 Colour ASTM ASTM D 1500 & D 6045 3,5 max Flash Point �°C ASTM D 93 60,0 min KIN. Viscosity @ 37,8�°C cSt ASTM D 445 2,0 min /6,0 max Copper corrosion @ 100�° C for 3hrs Rating ASTM D 130 1,0 max Distillation ASTM D 86 Recovery @ 360�°C % vol. 90,0 min Pour Point �°C ASTM D 97 + 6,0 max Sulphur Content % weight ASTM D 4294 0,05 max Carbon Residue on 10 % Residue % weight ASTM D 189 0,15 max Sediment by extraction % weight ASTM D 473 0,01 max Ash Content % weight ASTM D 482 0,01 max Water Content % vol. ASTM D 95 0,05 max Total Acid Number mg KOH/g ASTM D 974 0,5 max Strong Acid Number mg/KOH/g ASTM D 974 No-detectable Cetane Index ASTM D 976 45,0 min FAME ASTM D 7371 No-detectable
Silica Powder Introduction Silica powder has the advantages of excellent dielectric properties ,Low coefficient of thermal expansion, Complete chemical inertness and Neutral PH ,No chemical changes or induced reactions occur in either a catalyst or multicomponent. ChangTong silica power co.Ltd??s high purity silica power is produced for the electronic materials area ,sealants, electronic potting compound area .Its dispersion leveling is excellent, contraction and Coefficient of thermal expansion are small, Acid alkali resistance ,solvent insulation,,mechanical performance, Mixed epoxy resin transparency are all good. In total ,our excellent silica power can save cost and improve effectiveness for you . Silica Powder Properties Items Unit Typical testing value Moisture % 0.08 L.O.T. % 0.1 SiO2 % ã??99.6 Fe2O3 % 0.013 Al2O3 % 0.24 K2O % 0.003 CaO % 0.02 Na2O % 0.004 Mohs hardness 7 Density g/cm3 2.65 PH 6.5-7.0 whiteness ã??90 Oil Absorption (g/100g) 16-30 Melting point (??) 1730 Silica Powder Application Production Mesh witness Mons Performance Characteristics For silicon rubber use 1000-3500 ?¥ 95 7 1.Super White; 2.Extremely low moisture; 3.Good insulativity; 4.great reinforcing effect; For paint coating use 600-2500 ?¥ 95 7 1.High White; 2.Good Oil absorption,mix viscosity, dispersity, mobility; 3.Small angle of repose,rub resistance; For sealant use 800-2000 ?¥ 92 7 1.Moisture
Silicon Carbide Resistance Heater Single Screw 1550 Silicon Carbide Heating RodSpecifications 1. High working temperature: 1500C. 2. Long time last. 3. Varous type available. Rod, U, W, Single Spiral, Double Spiral Silicon Carbide Heating Rod Advantage . 1. High working temperature: 1500C (Surface Temperature) 2. Various shapes: Rod, U, W, Single Spiral, Doule Spiral shapes are availible. 3. Large size range: Diameter 14-54mm, Length 200-4500mm. 4. Fast Delivery: Normal quantity can be ready in 10 days. 5. Very competitive prices. How to Order Silicon Carbide Heating Rod 1. Choose the shape you need, like Rod, U, W, Single Spiral etc. 2. Out Diameter (OD) 3. Heating Zone Lengh (HZ) 4. Overall Length (OL) 5. Resistance you need. Order Sample: Rod type, OD30mm, HZ300mm, OL800mm, Resistance 0.4ohms. Silicon Carbide Resistance Heater Single Screw 1550 â?? 0 Silicon Carbide Resistance Heater Single Screw 1550 â?? 1 Normally the following should be given when describing any type of SiC heating elements: Type: ED, U, W, SC, SCR, DB,G, H, or DM Outside Diameter (OD) : mm Length of Hot Zone (HZ) :mm Length of Cold Zone (CZ) :mm Length of Overall(OL):mm Center Distance (A) :mm Resistance (at 1050â??+/-50â??) :�© Physical property of SIC heating element specific gravity 2.6~2.8g/cm bend strength >300kg hardness >9MOHS tensile strength >150kg/cm³ porosity rate
Technical index 1.Solvent-free acrylic powder (not contain any solvent) 2. Type: Non-Cross-linked Copolymer 3. VOC (Residual monomer) < 1000ppm 4. Particle Size (Average) : 20 ï½? 100 �¼m 5. Water content < 2% 6. Bulk density : 0.2 ï½? 0.6 g/cm3 Applications Additives for Cosmetics Improve skin feeling, flow characteristics, matte finish and optical blurring of wrinkles. May be used for lotion, cream and other essence such as in skin care products, sun care products, and make-up products. Recommended loading is around 1% ~ 5% depending on particular formulations. Additives for Painting oil and ink Matting agent, finish appearance enhancement agent and light diffusion agent. Also improve scratch resistance, and provide better feeling. Additives for Film and Coating May function as anti-blocking agent when applied in polyolefin, PET and other films. Particles do not scratch and damage the films surface due to spherical shapes, and do not hinder light transmissions through films due to its highly transparent nature. Additives for Others aspects May be used as evaporative pore-forming agent or evaporative binder for ceramic moldings; May be used as release improver for binder, fluid visualizing agent or adsorbent. The material for base of denture Additive and materials for 3D printing
Health benefits of refined coconut oil Prevent wrinkles, sagging skin, skin dryness, and flaking Reduces protein loss in hair and nourishes the hair Treats pancreatitis and Alzheimer's disease Prevent and effectively cures candida improve bone health Helps in easy digestion Strengthens immune system Prevents diseases affecting liver and kidney Effective in healing damaged tissues and infections Rich in lauric acid that helps maintain blood sugar and cholesterol levels SPECIFICATIONS: I. PHYSICAL CHARACTERS- VISUAL CHECKING Appear: Liquid, transparent, Homogeneous at 30oC, no impurities Ingredients: 100% coconut oil Color: Light yellow, natural color of product) Taste and flavor: Typical of coconut oil, no stranger flavor Foreign material: Not detected II. CHEMICAL STANDARD NO. ITEMS UNIT STANDARD 1 Free fatty acid (as lauric acid) % â?¤ 0,1 2 Peroxide value Meq/kg 4 3 Iodine Value g/100g 104 Moisture and volatile matter content % 0,1 5 Impurities % 0.05 6 Color 5,25 inch Lovibond cell 0,7 R/7,0 Y7 Saponification Value mgKOH/g 241-265 8 Slip melting point oC 23-26 9 Arsenic(AS) Mg/kg 0,1 10 Lead(Pb) Mg/kg 0,1 III, MICROBIOLOGICAL STANDARD NO. ITEMS UNIT STANDARD 1 Total aerobic plate count CFU/g
Price - Euro 9,92 Gift box for adult dogs with wet food, toy, treats and bowl. Schesir Chicken with Ham 150g- Raw materials: chicken fillet 61%, ham 4%, rice 1.5%. Additives per kg: vit.A 1650SV, vit.E 10mg. Analysis: protein 13%, fat 2%, fiber 0.1%, ash 2%, moisture 83%, 83.2 kcal/100 g. Barking Heads Lamb 300g- Ingredients: 85% lamb (60% fresh lamb, 25% lamb broth), sweet potatoes, spinach, courgette, peas, sunflower oil, salmon oil, seaweed, alfalfa, parsley, turmeric, anise, mint, Greek cheese seeds, Minerals Analytical Components (%): Crude Protein 10%, Crude Fat 6%, Crude Fiber 0.6%, Chaff 2%, Moisture 79% Nutritional Additives (per kg): Vitamins: Vitamin D3 450 IU, Vitamin E (DL-Alfa Tocopheryl Acetate) â?? 40 mg Microelements: Zinc as Zinc Oxide, 30mg, iron and Manganese, as Manganese (ll) Oxide, 2mg, Copper as Copper Sulfate Pentahydrate 0.4 mg, iodine as calcium iodate anhydrous 0.3 mg. No artificial colors, flavors or preservatives added. Arquivet Biscuits for dogs Bow Wow treats with stomach Bow Wow treat stick with beef, poultry liver and yucca.
We are manufacturer exporter & traders of wide range of Finished Leather & Goods, cow leather, goat leather, sheep leather, leather for shoes, leather goods garments ,these Finished Leather are provided by us at best quality and at best Competitive prices. Product category â?¢ Wet blue to finish leather (Cow & Buff) a) Full Grain / Correct grain (CG) / Smooth grain (SG) b) Napa c) Oil Pull up d) Burnish / Brush off e) Drum dyed f) Printed dry mile (Natural / Dye) g) New buck Lining (Pigment & Drum dyed ) Bharat Soul / Press Soul Upholstery Leather ( Cow & Buff) Jeans Label (Washable / Dranking effect on heating lobo / No color bleed / No Shrink/ No pigment finish/PU ) Rich compliance certificate Shoe Upper leather (Cow & Buff) Cg softy /Full grain softy /ndm/pdm/burnish/oil pull up/new buck/crunch /nappa. Shoe lining leather Pigment & drum dyed Customization Available
*1.*Origin product No sanctioned source: Kazakhstan, Azerbaijan, Georgia or Qatar. Dip and pay Commodity: EN590-10PPM Origin: Non-Sanctioned Countries FOB Fujairah Tank Take Over Net Price / Gross Price: $645/ $655 Trial Order Quantity: 200,000 MT Contract Quantity: Up To 400,000 MT per month Ã?? 12 months DIP & PAY TRANSACTION PROCEDURE 1. Buyer issues ICPO along with company registration certification, data page of Buyer's passport copy, or any I.D. 2. Seller issues Commercial Invoice. 3. Buyer signs CI and returns it to Seller with MT199/999 of Proof of payment as per Annexure "A", or a Bank Confirmation Letter delivered by Swift. 4. Seller releases POP cleared of Legalization and Notarization charges to Buyer for verification: A. Fresh SGS 48 hours id B. Certificate of Origin C. Company RegistrationCertificate D. Product Quality Passport E. Statement of Product Availability F. Unconditional Dip Test Authorization G. ATV Physically (Authorization to Physically Verify) 5. Buyer approves the above and makes payment by MT103/TT for the total value of the product as per CI and takes over the seller's tank.
Mimaki CE4 Printhead Assy - M008386 Product Specifications Technology: Multi-drop grayscale micro-piezo Grayscale levels: 16 Active nozzles: 318 Print swathe width: 53.6 mm Nozzle pitch: 169 �¼m Native resolution: 150 dpi Printhead weight: 148 g Dimensions: 85 x 70 x 23 mm Drop volume: 6 - 90 pl Typical firing frequency: 2.8 - 28 kHz Ink Compatibility: oil-based pigment ink and UV curable pigment ink Manufacturer: Mimaki Printer compatibility: Mimaki UJV-160 / JFX / UJF DP part number : PPHMI7917 This Printhead Assy is suitable for the Mimaki UJV-160 / JFX / UJF Printers. This is the original Mimaki part (number M008386). It includes the metallic support for fixation. The same printhead without the metallic support is sold as part number KX-CE308644CS-CE4. The cables are 40.9cm long, 2.1cm wide and have 20 pins.
Mimaki CE4 Printhead Assy - KX-CE308644CS-CE4 Product Specifications Technology: Multi-drop grayscale micro-piezo Grayscale levels: 16 Active nozzles: 318 Print swathe width: 53.6 mm Nozzle pitch: 169 �¼m Native resolution: 150 dpi Printhead weight: 148 g Dimensions: 85 x 70 x 23 mm Drop volume: 6 - 90 pl Typical firing frequency: 2.8 - 28 kHz Ink Compatibility: oil-based pigment ink and UV curable pigment ink Manufacturer: Mimaki Printer compatibility: Mimaki UJV-110 / UJV160 / JFX-1615 / JFX-1615Plus / JFX-1631 / JFX-1631Plus / UJF-706 DP part number : PPHMI8415 This Printhead Assy is suitable for the Mimaki UJV / JFX / UJF-706 Printers. This is the original Mimaki part (number KX-CE308644CS-Gen4). This part does not include the metallic bracket that can be easily re-used from the previous head. If the metallic bracket also needs to be replaced, part number M008386 should be purchased instead.
Basic Infomation Grade: B101 CAS No.: 13463-67-7 Formula: TiO2 EINECS: 236-675-5 Colour: White Appearance: Powder Transport Package: Woven Bag Specification: 25kg/bag HS Code: 32061110 Product Description B101 is an anatase titanium dioxide pigment manufactured by the sulfate process for general use. The grade is a fine, dry, white powder with excellent whiteness, strong covering power, high coloring power and good weathering resistance. It's widely used in coatings(Indoor), chemical fiber, plastics(PVC, Masterbatch), paper-making, shoe materials, glass beads and other fields. Physical Properties Property Standard TiO2 Content % 98.5 Color (Compared with standard sample) No lower than Tinting strength % 100 Loss of 105 C % 0.5 Oil absorption g/100g 23 Water-soluble salt content % 0.5 pH value of aqueous suspension 6.5 ~ 8.0 Residue % (0.045mm Sieve pore) 0.05 Resistivity of aqueous extract �©.m 20 Dispersity % 60 Application Coatings(Indoor), chemical fiber, plastics(PVC, Masterbatch), paper-making, shoe materials, glass beads and other fields. FAQ Q1: Are you a manufacturer or trading company A1: We are a professional manufacturer of titanium dioxide and barium sulfate,
POUPC1003 Lubricant Friction Modifier Description POUPC1003 is a liquid organic Molybdenum complex free of sulfur and Phosphorus. It can function as a friction modifier and antioxidant in engine oils,industrial oils and greases, and largely enhance lubricantsâ?? overall performance. Chemical name Molybdenum-Amine complex CAS No.:445409-27-8 Treat Level: Lube oils:0.2-1.0%, grease: 1.0-3.0% Highlights: Free of Sulfur or Phosphorus More environmental friendly Excellent friction-reducing property Good synergy with ZDDP and ADPA Properties Item Specification Test Method Appearance Deep brown liquid -- Solubility Soluble in lubricant bases -- Density(20â??)g/cm3 1.00-1.10 GB/T2540 Viscosity(100â??) cSt 25-40 GB/T265 Flash Point(COC), â?? 150 GB/T3536 Mo, % 7.0-8.0 SH/T0749 N, % 2.0-3.5 SH/T0656 Packing 200kgs/drum(net weight) Storage information Not dangerous chemical. Kept under cool, dry and well ventilated warehouses. For more information,please refer to the relevance MSDS
ECTFE Coating Grade Resin 1.Product introduction As a resin, ethylene chlorotrifluoroethylene is a very pure fluorine copolymer, which not only has excellent mechanical properties, good weather resistance and chemical resistance common to fluorine-containing resins, but also has excellent light transmittance and hardly absorbs visible light and ultraviolet light. In addition, because it contains chlorine atoms, the moisture permeability of all fluorine resins is relatively low, which can prevent many liquids and gases from penetrating, and is beneficial to the anticorrosion and rust prevention of the protected substrate. 2.Technical Parameter Item Test Method Unit Value Density ASTM D792 g/cm3 1.66~1.68 Grain Size ASTM D1921 um 40~80 Melting Point ASTM D3418 �ºC 215~225 Melt Index ASTM D1238 g/10min (275�ºC,2.16kg) 8~15 3.Mark, Packing, Storage & Transportation 3.1 Mark The packing bags (boxes) of this product should be clearly marked with firm company name, product name, batch number, brand number (specification number), net content, etc. 3.2 Package This product is packed in paper barrels (lined with polyethylene plastic bags) with a net content of (20 �± 0.2) kg per barrel. Each barrel shall be provided with a product certificate, including: company name, product name, batch number, brand (specification number), net content and production date, etc. In case of special packaging, the supplier and the Demander shall negotiate separately. 3.3 Storage This product should be stored in a clean, cool and dry place to prevent rain, sunshine, moisture, dust and other impurities. 3.4 Transportation This product is transported according to non-dangerous goods. Moisture and severe vibration should be avoided during transportation. 4.Main Application 4.1 ECTFE coating grade resin is white powder, which has excellent chemical corrosion resistance, excellent barrier performance to various corrosive gases and excellent high and low temperature resistance. 4.2 The electrostatic spraying method can be used for coating protection of reactors, pipelines, storage and irrigation, mixers and other containers in the chemical and semiconductor fields, thus delaying the service life of the equipment.
Paddle Tennis and Platform Tennis Wire As is known, paddle tennis and platform tennis courts have specific and rugged requirements towards its courts' fence for its special exercise modality. Hexagonal wire mesh is just the designated fence. The 16 gauge wires are triple continuous twisted and then galvanized, GAW (galvanized after weave), to make into a 1" opening mesh. The wire is dipped into a rust inhibiting bath of molten zinc, which will guarantee the zinc coated rate is above 350 g/m2. The heavily galvanized and thicker wire than normal chicken wire assures a corrosion resistant ability to adapt for the adverse circumstance in winter. The size of each roll of wire mesh would be 72" Ã?? 180', weighted 328 lbs. Except for paddle tennis and platform tennis courts' fencing wire mesh, the same mesh is well performed to be used as conductor on the ceiling of bumper car rides. Specification: Material: heavily galvanized woven hexagonal netting. Wire: 16 gauge. Zinc rate: above 350 g/m2. Manufacture: triple continuous twisted and galvanized after woven. Mesh size: 1". Size of rolls: 72" Ã?? 180'. This is a huge size paddle tennis court with a high platform on ground and chicken wire mesh made fence protect it. PTW-01: A standard paddle tennis court with hexagonal wire netting made fence. This an empty paddle tennis court in winter by day. PTW-02: 16 gauge wire 1" mesh opening hexagonal mesh used as paddle tennis and platform tennis fencing wire mesh. Two adjacent paddle tennis courts, one has people playing inside, and American national flag is flying. PTW-03: Two adjacent paddle tennis courts are both made from hexagonal netting and posts to fix the wire mesh fence. A empty paddle tennis court has kermesinus posts and galvanized hexagonal wire mesh. PTW-04: Paddle tennis court with chicken wire mesh and kermesinus posts. An enlarged paddle tennis courts fence wire in front, the smaller mesh behind. PTW-05: Paddle tennis wire detail with enlarged part in front.
D2 Diesel Gas Oil is offered by our end sellers considering the needs of diverse industrial sectors. We provide D2 Diesel Gas Oil in different grades. Our D2 Diesel Gas Oil is mainly used to run several industrial as well as commercial automobiles. We take up bulk orders of D2 Diesel Gas Oil and deliver it timely. Our D2 Diesel Gas Oil is available at competitive rates. Minimum ordered quantity of our D2 Diesel Gas Oil should be 50.000MT Grade Available: D2 DIESEL GAS OIL L-0.2-62 GOST 305-82 OFFICIAL GUARANTEED SPECIFICATION FOR RUSSIAN ORIGIN GAS OIL 0,2/62 GOST 305 â?? 82 RUSSIAN GAS OIL D2 GOST 305Ã?Â82 COMPONENT INIT MIN MAX Density@ 20 deg C Kg / m3 0.870 Colour 1.0 2.0 Flash point, PMCC Deg C (C) 57 66 Kinematic viscosity @20 deg C C ST 3.0 6.0 Pour point Deg C (C) (*) 10.0 Cloud point Deg C (C) (*) 5.0 Mercaptan Sulphur 0.01 Acidity, mg / 1000 cm3 5 Iodine number g/100g 6 Ash %wt 0.01 Total Sulphur %wt 0.01 0.02 Copper corrosion 3hrs@50 deg C (Typical) 1 A CCR on 10% Residues %wt 0.20 Cetane Index 45 Distillation range: - 50% Recovered Volume deg C (C) 280 - Ã?Â90% Recovered Volume deg C (C) 350 - Bacteria MBC Fibre / it 500 - Bacteria CFU Fibre / it 1000 (*) Summer from March to October (PP 5.0 degrees C) Summer from March to October (CP 0.0 degrees C) Winter from November to February (PP 10.0 degrees C) Winter from November to February (CP 5.0 degrees C) The product is guaranteed by Seller not to contain bacteria and other living organism contamination above normal level (1000 CFU/l).
Origin: EU Products: - DURUM WHEAT G 2 - Red Hard Winter Wheat- Grade 2 - SOFT MILLING WHEAT G 2 See more details on our website AKTIVA TRADING under COMMODITIES. QUANTITY & PRICE: 12,500 Mts min â??50,000 Mts Max per Month - Durum Wheat : $ 475.00 CIF any safe world port - HARD Wheat : $ 450.00 CIF any safe world port - Soft Milling Wheat : $ 425.00 CIF any safe world port Wheat supply Subject to Availability. DESTINATION & DELIVERY: Destination: CIF ASWP. Shipment: First Shipment in 30-45 Days and Rest in Every 30 Days after Receipt of Payment Instrument to the Sellerâ??s Bank. PAYMENT: By Irrevocable, Transferable, Confirmed DLC 100% Payment at Sight for total Quantity from Top Western Prime Bank. PERFORMANCE BOND: The Seller will Post 2%Performance Bond after Receipt of Payment Instrument to the Seller. INSPECTION: S.G.S Inspection for Quality and Quantity Service at Sellerâ??s Cost will inspect the Commodity at Place of Loading. PROCEDURES: 1) Buyer issues a LOI + RWA/BCL 2) Seller issues FCO 3) Buyer sign seal and return the FCO 4) Seller issues Draft Contract 5) Buyer sign seal and return the Contract, seller sign the Contract and return to the Buyer 6) Buyer Bank sends a Non-operative DLC for to the sellerâ??s Bank 7) Sellerâ??s Bank sends PB 2% to the Buyerâ??s Bank and Activate the Payment Instrument. 8) DLC Becomes operative. 9) Shipment Starts. Looking forward for your Long term Co-operation. NOTE: THE PRICES INCLUDES US$1.00 COMMISSIONS AND PLEASE ADD ONLY LOW COMMISSIONS US$1-2 PMT .ANY OVER PRICE SHALL BE SPLIT INTO 50:50 RATIO FOR SELLER AND BUYER. Price is subject to change without prior notice. All prices are Indicative , please contact us for updated current price and offer .
It is with the earth rare element cerium so cerium stabilized zirconia bead has the biggest specific gravity in all zirconia beads series and it is very suitable for some special industries and grinding materials, especially for milling and dispersing high viscosity pastes and high purity products. (1).Wear-resistant, corrosion-resistant products: paints, textiles, paints, printing and dyeing; (2). High strength, high toughness products: magnetic materials, piezoelectric ceramics, dielectric ceramics; (3).To prevents pollution: medicine, food, cosmetics; (4).Ceramics: Electronic ceramics, refractory ceramics, structural ceramics. Features: It has a gem-like hardness and density.Micro-structure of delicate, uniform, dense ceramics of the Quartet. Its excellent wear resistance and fracture toughness is particularly suited for grinding and dispersing high-solid-phase high-viscosity, high hardness of the paste. (1).Long working life: 30 times longer life than glass beads, 6 times than zirconium silicate beads. (2)High grindingefficiency: around 6 times than glass beads; 2 times than zirconium silicate bead (3).Excellent wear resistance and fracture toughness. Products Dimension Ball 0.4-0.6mm 0.6-0.8mm 0.6-0.8mm 0.8-1.0mm 1.0-1.2mm 1.2-1.4mm 1.4-1.6mm 1.6-1.8mm 1.8-2.0mm 2.0-2.2mm 2.2-2.4mm 2.4-2.6mm 2.6-2.8mm 2.8-3.0mm Physical parameters Composition Wt% 20% CeO2 + 80% ZrO2 Specific Density g/cm3 6.0 Color Yellow/Gold Bulk Density g/cm3 3.85 Hardness Mohs 9 Elastic Modulus GPA 200 Thermal Conductivity W/m.K 3 Crushing Load KN 2000(2mm) Fracture Toughness Mpam1-2 8.5 Thermal Expansion Coefficient 10*10-6/â??(20-400) 9.0 Wear Loss ppm/hr
JOJOSE BRAND COMPOUND POTATO CHIPS Exporting to over 130 Countries Provide One-Stop Purchase of Potato Chips Multi Types Selections with Canned / Bag / Flavors / Shapes Tasty Noodles & Incredible Flavour, Taste as Good as Korean Brand Ramen Factory Quality Certificates: BRC / FDA / HACCP / ISO / HALAL / KOSHER, etc. Strong Competitive Prices Professional & Quick & Efficient in Feedback JOJOSE is the BEST supplier of Potato Chips in China, JOJOSE will be your right CHOICE!!! Pls consider our potato chips' advantages: a). Exact Pavan machines: Exact Pringles size, crunch texture, bigger size with thinner thickness. b). Potato Chips with Non - GMO, Low fat, Cholesterol & Trans-fat Free, No artificial colors, without Preservatives. c). Stonger private label services to International retailers all over the world. d). Imported raw material, all halal. e). Free design support. f). Faster delivery date. g). Longer shelf life. h). 24-hour services; JOJOSE FOODS is specializing in producing and exporting food and snacks for over 30 years. We have joint-ventured factories with a strong ability to supply our clients the various high-quality products at competitive prices. All our factories are equipped with advanced production lines, with the quality control certifications of HACCP, ISO, HALAL, USA FDA, BRC, KOSHER, etc. Our products cover Instant noodles, Potato chips, Canned foods, Drinks, etc. products. We have been exporting our products to many countries around the world, including strict countries like the USA, UK, Australia, Canada, South Korea, Sweden, The Bahamas, and Poland�?�¢?�?�¦. We are confident to meet the demand of Clients from all over the world. With the strong experience of the R&D Team, we have been satisfying many Clients by providing them with the right products with the right taste for their market. The superior quality, good color, competitive price, and fantastic taste lead us to be the leading supplier, exporting the products to more than 100 countries and regions. We provide OEM/ODM services and looking for distributors all over the world. Contact us for more details, the good business starts here!
Quick Information Brand Name: NATAI Place of Origin: China Model Number : Natai 02 CAS No. : 70693-62-8 Purity : Compound Powder Molecular Formula : 2KHSO5/KHSO4/K2SO4 Molecular Weight : 614.7 Application : water disinfection Appearance : white powder Chemical : Potassium Monopersulphate Potassium Monopersulfate compound is a kind of acid oxidant, a free flowing white granularly powder, and soluble in water. Other Names are Potassium peroxymonosulfate, potassium monopersulfate compound, Potassium hydrogen sulfate, PMPS,KMPS, ect. Molecular Formula: 2KHSO5/KHSO4/K2SO4 Molecular Weight: 614.7 CAS NO.: 70693-62-8? Packaging: 25Kg/ PP Bag. Reactive oxygen species % �4.5-4.9 Active ingredients(KHSO5)% �42.8-46 Bulk density g/ml 0.8-1.2 Moisture % 0.15 Through the United States screening #20,% 100 Through the United States screening #200,%8 PH value (25 ° C) 1% aqueous solution 2.3 PH value (25 ° C) 3% aqueous solution 2 Solubility(20°C)g/L 256 Stability, % reactive oxygen loss/ month 90%); reaction temperature is too low, energy consumption is large, industrial production must be on the refrigerator can be achieved, and also need to take away from the closed container reaction by-product hydrogen chloride Gas; the reaction of the composite salt mixture obtained after 12 hours centrifugal separation can be obtained, and therefore more difficult to achieve in industrial production. Anodizing method: to use expensive platinum electrolytic cell, equipment investment, high energy consumption; product was paste, difficult to crystallize. Products at room temperature is very unstable, severe loss of reactive oxygen species, low yield. We used sulfuric acid method: sulfuric acid and hydrogen peroxide reaction prepared by a sulfuric acid solution, the solution with the basic potassium compounds were prepared by potassium bisulfate complex salt solution, crystallization, filtration and drying, and then mixed with anti-caking agent, the system get the final product. Application Application industry Disinfection / animal breeding industry Instructions Animal environment disinfection, aquaculture water treatment, can kill almost all the zoonotic diseases of bacteria and viruses, foot and mouth disease, avian flu, SARS and so have an excellent role in the killing. Hospitals, homes, poultry and aquaculture disinfectants and water quality improvers, soil improvement and remediation / agricultural disinfectants, tap water pre-oxidation, disinfection and sewage treatment , swimming pools and SPA water treatment, electronics micro etchants, wood cleaning , Paper industry , food industry , wool shrinkage treatment, cosmetics and daily chemicals. Price Delivery Port : China Packaging & Delivery Packing :25kg paper bag, plastic woven bag Delivery Lead Time : NegotiableSupply Ability : 6000 MT per year
Products standard processing and traceability 1. Fermentation period varies by each specialty process 2. The drying period varies with each specialty process (7 - 45 days) 3. 100% Arabica green beans 4. Varieties: Mix (Tim Tim, Bourbon, Ateng Super, P88, Cattimor, Gayo 1, Gayo 2) 5. Altitude: 1500 - 1800 masl (meters above sea level) 6. Moist: 12%, Defect: 4% 7. Passage Trough A Screen, % (w/w) ê?? 5mm: 0 - 5 max 8. Grade 1 double pick / triple pick international grading standard ONLY. 9. Harvesting periods: From February to May & From September to December 10. Specialty Coffee Association standard 11. Quality Reference : SNI.01-2907-2008 / 12. ICO (International Coffee Organization) Terms a) Will process the production until export ready after signing the contract. b) 2 - 3 months depending on quantity and types of specialty beans c) FOB Belawan Port, Medan, Indonesia d) CIF applicable with upfront e) 100% Cash Against Documents (CAD) f) 100% LC by only top reputable banks g) Packaging: Double bags of Jute Bag and Grainpro Bag inside (1 bag = 60 kilogram) Order quantity 1 FCL of 20'â??= >200 bags to max 345 bags LCL with Minimum order quantity per beans (MOQ) = 10 bags = 600 kilograms (can mix) International grading standard: 1. G1 grade beans (Double Pick-DP) Moist 14% and Defect 8%. 2. Premium Grade beans (Triple Pick- TP) Moist 12% and Defect 4%. Only by 60 kg bags MOQ 1 container 20 footer (can mix) Our Gayo Arabica specialty coffee green bean types: -Wet Hulled G1 (commercial grade) -Fully Washed -Natural -Natural on Aerobic -Honey -Winey Soft (Wine Process)
