Model L086TIM Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 315(232)/2300 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111x 139 Mean piston speed (m/sec. ) 10.66 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 62 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 27 / 25 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT110A (Dong-I) Gear ratio 1.77 2.09 2.42 2.82 3.19 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,364 x 919 x 965 with M. gear mm 1,552 x 919 x 1,062 Engine dry weight without M/G kg 790 with M. gear kg 1,015
Model L136TI Engine type 4 cycle In line direct injection water cooled with turbo charger inter cooler Rating output BHP PSkWrpm 2301692200 Displacement cc 8071 Cylinder number bore x stroke mm 6 111x 139 Mean piston speed msec 1019 Compression ratio 167 1 Firing order 1 5 3 6 2 4 Governor type of injection pump Mechanical all speed RSV Fuel consumption lit h 45 Starting system Electric Starting by starter motor Starter motor capacity V kW 24 45 Alternator capacity V A 24 50 Battery V Ah 24 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max Min lit 27 25 Fresh water pump type Centrifugal type driven by V belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT110A DongI Gear ratio 177 209 242 282 319 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size L x W x H without MG mm 1364 x 911 x 937 with M gear mm 1552 x 911 x 1027 Engine dry weight without MG kg 773 with M gear kg 994
Model L136T Engine type 4 cycle, In line, direct- injection, water cooled, with turbo charger Rating output (B.H.P) PS(kW)/rpm 200(147)/2200 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111x 139 Mean piston speed (m/sec. ) 10.19 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 37 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 27 / 25 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT90A (Dong-I) Gear ratio 1.61 2.06 2.45 2.82 3.12 3.46 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,351 x 893 x 937 with M. gear mm 1,351 x 893 x 937 Engine dry weight without M/G kg 748 with M. gear kg 938
Model L136 Engine type 4 cycle, In line, direct- injection, water cooled, aspirated naturally Rating output (B.H.P) PS(kW)/rpm 160(118)/2200 Displacement( cc ) 8,071 Cylinder number - bore x stroke( mm ) 6 - 111 x 139 Mean piston speed (m/sec. ) 10.19 Compression ratio 17.6 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 32 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 4.5 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 100 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 25 / 23 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT90AF (Dong-I) Gear ratio 1.61 2.06 2.45 2.82 3.12 3.46 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,266 x 875 x 937 with M. gear mm 1,542 x 875 x 963 Engine dry weight without M/G kg 743 with M. gear kg 928
HY-1040 Molecular formula H2[AI2O3·mSiO2(OH)2]·nH2O Properties This product is a sub-white powder, which is not dissolved in water, oil or organic solvent. It has strong properties as cation exchange capacity, selective adsorption, hydrophilic property, surface activity and catalysis, It can adsorb and eliminate mineral materials as pitch, neutral colloid, sulfide and olefinenaphthenic acid in lubrication to improve the durability and photo-stability of the lubricant and to increase the ability of corrosion-resisting, and can also absorb and eliminate the pigment, aflatoxin and the carcinogenic substance of 3-4 benzpyrene in vegetable oil, in addition, it has strong ability of oil, in addition, it has strong ability of oil decolorization, high speed of filtering oil and low oil retention of filter cake. Functions�¯�¼?it's widely used in the absorption and refinement of lubricant, paraffin wax, and vaseline, the decolorization of animal and vegetable oil, and the purification of honey, wax and glycerine. Specifications Performance indicators of activated clay Technical requirements for active clay manufacturers' products: 1, appearance: grey or light fine powder. 2, water (2 hr. 105 C) : 12% 3, decoloring force: 154 4, active degree: 180 mol/kg 5, particle size (0.076 mm) : 95% 6, free acid (in - H2SO4) : 0.20% 7, heavy metal content (Pb) : 10 mg/kg 8, arsenic content: 3 mg/kg
Technical Parameters Travel of X and Y Axes: 800x1200 mm; Maximum cutting thickness/ Maximum height of the part: 700 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 985x1580 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 160 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150 �¼s; Approx. Machine size (LxWxH): 2600x2400x1800 mm; Approx. Machine weight: 4500 kg; Approx. Machine control cabinet size: 670x630x1800 mm; Approx. Machine control cabinet weight: 200 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 â??. ;
Technical Parameters : Travel of X and Y Axes: 500x630 mm; Maximum cutting thickness/ Maximum height of the part: 600 mm; Maximum Work piece weight: 700 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 600x860x600 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 150 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150; Approx. Machine size (LxWxH): 2000x1950x1750 mm; Approx. Machine weight: 2540 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 ;
Technical Parameters : Travel of X and Y Axes: 800x630 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1130x9500x300 mm; Maximum Work piece weight: 750 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2200x1650x1910 mm; Approx. Machine weight: 2980 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters: Travel of X and Y Axes: 630x500 mm; Maximum cutting thickness: 350 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 m mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1020x640x350 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 2180 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters Travel of X and Y Axes: 500x400 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 850x540x300 mm; Maximum Work piece weight: 450 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 1790 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters Travel of X and Y Axes: 400x320 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 620x480x300 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Numerical Control System: X8 ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1700x1300x2160 mm; Approx. Machine weight: 1480 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 800x630 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1130x9500x300 mm; Maximum Work piece weight: 750 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2200x1650x1910 mm; Approx. Machine weight: 3000 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 630x500 mm; Maximum cutting thickness: 350 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 m mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1020x640x350 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 2200 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 500x400 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 850x540x300 mm; Maximum Work piece weight: 450 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM or HL SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1960x1620x2160 mm; Approx. Machine weight: 1800 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Technical Parameters : Travel of X and Y Axes: 400x320 mm; Maximum cutting thickness: 300 mm; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 620x480x300 mm; Maximum Work piece weight: 300 kg; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " u.m; Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: More than 120 square mm/min; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version ; Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function ; 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1700x1300x2160 mm; Approx. Machine weight: 1500 kg; Approx. control cabinet size (LxWxH): 670x700x1100 mm; Approx. control cabinet weight: 100 kg.
Automatic Stirrup Bending Machine Works With Raw Metarial Coil Type of Wire Ribbed & Smooth Production Capacity (mm) Singlewire: 10-12 / Doublewire: 6-8 Max. Bending Opportunity CW and CCW/Birectional Rated Power 2 Servomotor 7,5 + 5,5 KW Driving Motor 7,5 KW (servo motor) Bending Motor Power 5,5 KW (servo motor) Length Tolerance ± 1 mm Bending Tolerance ± 1 Driving Speed 90m/minutes Bending Speed 1200 / sec. Pre-Strainghtening Unit X and Y Axis With multiple rollers Control Unit Operator sensitive/friendly program, Shapes can be easily created helping with angles and length by operator. The program was written by Sew engineers. Driving Unit Industrial type gearbox by EMPO Bending Unit Industrial type gearbox by EMPO Cutting Heav type industrial gear box Averageair - compressed consumption 6H/min Average - electric power consumption 4-6/Kw/h Compressor Needed 200lt/min Working Pressure (bar) 6 Bar Voltage 380v-50Hz-3Fhaze Switch - Sensors Proximith Switches Encoder 1024 Pulse/Sick Brand Driving Gear Box 2379 Grade With Heat Treatment Control Panel Type LCD 18 Machine Dimensions (W x L x H) 1500mm x 4600mm x 1900mm Machine Weight 2700 Kg Control Program Language TR, ENG, FR, ARAB
ATLAS-WT3 Freight Elevators ln the elevator car, fixed limit devices are installed on the left and right sides of the floor, and retractable limit devicesare installed near the front door to prevent the car from scratching to the elevator. Features Of ATLAS-WT3 Commercial Freight Elevators Automobile Limiting Device In Car. Landing Floor Call Elevator Device. Specification Of ATLAS-WT3 Freight IFE Elevators NO. Specification ATLAS-WT3 1 Capacity (kg) 2000 2500 3000 2 Speed (m/s) 0.5 1 0.5 1 0.5 1 3 Operation System full collective selection operation 4 Driving System VVVF 5 Door Operator System VVVF 6 Traction Machine Permanent Magnet Synchronous Gearless type 7 Control System CTRL80 8 Car Dimension mm 1800Ã??2300 2000Ã??2500 2300Ã??2500 width*depth 9 Shaft Size mm 3000Ã??2700 3300Ã??2900 3600Ã??2900 W*H As one of escalator and elevator companies, we will do our best to meet all the needs of customers.
Railway Crow Bar It is for situations such as these that the jim-crow comes into its own. The jim crow was slotted over the rail about four or five sleepers away from the offending joint.and the screw tightened until it engaged with the edge of the rail. Then tightened the screw a further half-turn - thus bending the rail slightly.This process was repeated, moving the jim crow one sleeper nearer the joint each time and each time adding one more half-turn. This introduces a gradually increasing curve to the rail as it nears the joint.If you compare these two pictures with those showing the kinks above, you can see the difference. The amount of bend can be tailored to suit each location - and if it turns out that have made the curve too severe, the jim crow can be slotted on the opposite way round and tightened up to ease the curve. Specification item value Type Crowbar Railway Material Steel Dimensions (L x W x H) (mm) 1500mm, 1800mm Place of Origin China Hubei Brand Name Linkage Item railway crowbar Brand Name Linkage Application Wrecking & Demolition, DiggingChiseling Tip Type Chisel End, Rolled Nail Puller for High Leverage, Heeled Pinch End Length 1500mm, 1800mm Weight 6 KG
Railway Crow Bar It is for situations such as these that the jim-crow comes into its own. The jim crow was slotted over the rail about four or five sleepers away from the offending joint.and the screw tightened until it engaged with the edge of the rail. Then tightened the screw a further half-turn - thus bending the rail slightly.This process was repeated, moving the jim crow one sleeper nearer the joint each time and each time adding one more half-turn. This introduces a gradually increasing curve to the rail as it nears the joint.If you compare these two pictures with those showing the kinks above, you can see the difference. The amount of bend can be tailored to suit each location - and if it turns out that have made the curve too severe, the jim crow can be slotted on the opposite way round and tightened up to ease the curve. Specification item value Type Crowbar Railway Material Steel Dimensions (L x W x H) (mm) 1500mm, 1800mm Place of Origin China Hubei Brand Name Linkage Item railway crowbar Brand Name Linkage Application Wrecking & Demolition, DiggingChiseling Tip Type Chisel End, Rolled Nail Puller for High Leverage, Heeled Pinch End Length 1500mm, 1800mm Weight 6 KG
VAMB-ME Hospital Elevators Types VAMB series of medical elevator couId be specialized designed according to customer's demand Smooth running, precise IeveIing, exceIIent ventilation system, soft and harmonious decoration IFE series of medicaI eIevator win a high degree of appreciation by all of its passengers. Features of VAMB-ME Hospital China Elevators Suspending double fans, enjoyable the space with clean and cool air. Negative-ion generator. meticulous service, comfortable care. One button set to keep the door open longer, no need for manual operation. Specification Of VAMB-ME Hospital Elevators NO. Specification 1275171600(21) Capacity (kg) 1275 1600 1 Speed (m/s) 1 1.75 1 1.75 2 Operation System full collective selection operation 3 Driving System VVVF 4 Door Operator System VVVF 5 Traction Machine Permanent Magnet Synchronous Gearless type 6 Control System CTRL80 7 Parallel Elevators 2 units 8 Group Control Elevators 3-8 units 9 Car Dimension mm 1200*2300 1400*2400 width*depth 10 Shaft Size mm 2100*2750 2400*2850 W*H 2400*2700 2350*2900 Now the price of passenger lift cabin is reasonable, if you have needs, please contact us.