YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT Self-luminous Safety Aluminum Road Stud With Reflectors Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF27 Product name YT Self-luminous Safety Aluminum Road Stud With Reflectors Material Aluminum base +Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 302.4*51.8mm Weight 118g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance 750 (3)_.jpg750 YF27 (5)_.jpg750 YF27 _.jpg750(4)_.jpg750(6)_.jpgYF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer. 12
YT self-luminous ABS plastic reflective road stud with Nano-fluorescent material Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF06 Product name YT self-luminous ABS plastic reflective road stud with Nano-fluorescent material Material ABS+reflective film+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 100mmÃ?100mmÃ?10mm Weight 112g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF06 (1)_.jpgYF06 (2)_.jpgYF06 (3)_.jpgYF06 (4)_.jpgYF06 (5)_.jpgYF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
Factory saqure self-luminous road stud delineator with reflective panels Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF08 Product name Factory saqure self-luminous road stud delineator with reflective panels Material ABS+self luminous Color white/ yellow/ red/ green/ black Size 100mmÃ?100mmÃ?20mm Weight 133g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF08 (1)YF08 (1)YF08 (1)_.jpgYF08 (2)_.jpgYF08 (3)_.jpgYF08 (5)_.jpgYF08 (6)_.jpgYF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
Hangzhou YT Self-illuminating ABS road stud d with strong visibility Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF22 Product name Hangzhou YT Self-illuminating ABS road stud d with strong visibility Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 100mmÃ?100mmÃ?20mm Weight 145g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF22 (2)_YF22 (3)YF22 (4)YF22 (3)YF22 (6)YF22 (2)YF22 (1)YF self-luminating series table of brightnessYetong road studplastic road stud_application
Product Code YRG45 Product name China Supplier High Reflective Plastic Reflector for road stud Material ABS base+PS/PMMA reflective panel Color white/ yellow/ red Size 92.7mmÃ?28.9mm Weight 11g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance
Product Code YRG31 Product name China Supplier Plastic 180*40mm Glass Beads Reflective Reflector for bike Material ABS base+glass beads Color white/ yellow/ red/ green/ black Size 180mmÃ?40mm,170 beads Weight 38g Application reflective panel, road stud, delineator, speed humb, etc, Feature high weight resistance, colorful, antioxidant, durable, 360° high reflectivity Payment terms T/T, L/C, Western union, Trade Assurance
Product Code YRG39 Product name China Supplier Round High Reflective Plastic Glass Beads Reflector with murano glass beads Material ABS base+glass beads Color white/ yellow/ red/ green/ black Size 158 beads Weight 34g Application reflective panel, road stud, delineator, speed humb, etc, Feature high weight resistance, colorful, antioxidant, durable, 360° high reflectivity Payment terms T/T, L/C, Western union, Trade Assurance
Product Code YRG38 Product name 2019 NEW high quality glass beads reflective panel with 158 Cateyes Material ABS base+glass beads Color white/ yellow/ red/ green/ black Size 158 beads Weight 30g Application reflective panel, road stud, delineator, speed humb, etc, Feature high weight resistance, colorful, antioxidant, durable, 360° high reflectivity Payment terms T/T, L/C, Western union, Trade Assurance
Product Code YRG63 Product name China Supplier High Reflective Lattice Plastic Reflector for Highway Material ABS base+PS/PMMA reflective panel Color white/ yellow/ red Size 120mmÃ?70mm Weight 30g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance
Material ABS base+glass beads Color white/ yellow/ red/ green/ black Size 12 beads Weight 2g Application reflective panel, road stud, delineator, speed humb, etc, Feature high weight resistance, colorful, antioxidant, durable, 360° high reflectivity Payment terms T/T, L/C, Western union, Trade Assurance
Height: 100 cm Base size: 49 x 49 cm Product above the plastic, the base rubber
MESH 42X56CM 18LED
SPEC: .54LED .Rechargeable battery,DC
Square Sign Posts · Posts are manufactured conforming to FHWA and ATSSA standard. · Steel material conforms to ASTM A1011, Grade 50. Yield strength after cold-forming is 60,000 psi minimum. · Posts are manufactured from hot-dipped galvanized steel conforming to ASTM A653, G90 or G140. The posts are also coated with a chromate conversion coating and a clear organic polymer topcoat. · Punching with 7/16" holes on 1" centers on all four sides down the entire length of the post. · Five kinds of cross section including 1.50?�X1.50", 1.75", 2.00", 2.25", and 2.50"X2.50". · Available in 12 and 14 gauge thickness with all kinds of length according to your demand. · Powder coated sign posts with all kinds of colors are also available.
Square Sign Posts Posts are manufactured conforming to FHWA and ATSSA standard. Steel material conforms to ASTM A1011, Grade 50. Yield strength after cold-forming is 60,000 psi minimum. Posts are manufactured from hot-dipped galvanized steel conforming to ASTM A653, G90 or G140. The posts are also coated with a chromate conversion coating and a clear organic polymer topcoat. Punching with 7/16" holes on 1" centers on all four sides down the entire length of the post. Five kinds of cross section including 1.50â?�X1.50", 1.75", 2.00", 2.25", and 2.50"X2.50". Available in 12 and 14 gauge thickness with all kinds of length according to your demand. Powder coated sign posts with all kinds of colors are also available.
U-Channel Posts Posts are manufactured conforming to FHWA and ATSSA standard. Steel material conforms to ASTM A499, Grade 60. All kinds of specification including 1.12lbs/ft, 2.00lbs/ft, 2.03lbs/ft, 2.08lbs/ft, 2.50lbs/ft ,3.00lbs/ft and more. 3/8" or 7/16"diameter holes on 1"or 2" centers, punched full-length. Available in hot-dipped galvanized, powder coated or painted. Galvanized by hot dipping per ASTM A123. Tapered ends are also available. Available in any length according to your demand. Yield and tensile strength: 60,000-80,000 psi.
mixture of sand Hesco barrier JOESCO 1.Wire Dia: 3, 4,5mm. 2.Various sizes: 0.61x0.61m, 1x1m, 2.13x2.21m, 2x2m,1.06x1.37m,1.5x1.36m,etc. 3.Geotextile: in non-woven geotextile , color can be white, beige-sand colour. can with or without geotextile . 4.Finish: Hot Dipped Galvanized , Galfan Coated after welded 5.Packing: wrapped with shrink film. 6.Features: easy to handle, the structure is strong , not break., long life. 7.Applications: good solution for emergency flood control, shelter house, military defence wall earth-filled defencive hesco barriers JOESCO Mesh size:75*75MM(3''*3'') Finished: Hot dipped galvanized and galfan. Geotextile:In heavy duty non-woven polypropylene. Geotextile color:white,earth yellow,dusty grey,etc Geotextile thickness:3mm(300g/m2). Package: Warapped with shrink film then packed in pallet,and the last packed with steel belt. Hesco barrier/hesco bastion, which is made of the steel welded mesh and lined with non-woven geotextile, can be filled with sand, earth, cement,stone, then as a defence wall or bunker and widely used in the military to protect safety. Perimeter security and defense walls barrier JOESCO JOESCO Barrier Manufacturer & worldwide exporter of various barrier Concertainer,Units are used for Security protection,resistance suddenly burst attacks,Nature Flood etc. control,Flood Control Bastion. Manufacturer:JOESCO HEBEI METAL PRODUCTS INC.
mixture of sand Hesco barrier JOESCO 1.Wire Dia: 3, 4,5mm. 2.Various sizes: 0.61x0.61m, 1x1m, 2.13x2.21m, 2x2m,1.06x1.37m,1.5x1.36m,etc. 3.Geotextile: in non-woven geotextile , color can be white, beige-sand colour. can with or without geotextile . 4.Finish: Hot Dipped Galvanized , Galfan Coated after welded 5.Packing: wrapped with shrink film. 6.Features: easy to handle, the structure is strong , not break., long life. 7.Applications: good solution for emergency flood control, shelter house, military defence wall earth-filled defencive hesco barriers JOESCO Mesh size:75*75MM(3''*3'') Finished: Hot dipped galvanized and galfan. Geotextile:In heavy duty non-woven polypropylene. Geotextile color:white,earth yellow,dusty grey,etc Geotextile thickness:3mm(300g/m2). Package: Warapped with shrink film then packed in pallet,and the last packed with steel belt. Hesco barrier/hesco bastion, which is made of the steel welded mesh and lined with non-woven geotextile, can be filled with sand, earth, cement,stone, then as a defence wall or bunker and widely used in the military to protect safety. Perimeter security and defense walls barrier JOESCO