Find Verified Evaporative Air Cooler Hpcf1 03I Suppliers, Manufacturers and Wholesalers

Basic principle:
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Parameter specification:
Airflow(m3/h):18000
Power(Kw) :1.1
Fan Type:Axle
Unit Size(mm):1080?1080?980
Discharge Type :up
Controller Type :Intelligent LCD
Voltage/Frequency(V/Hz):220/50
Motor Type:Single-phase Various FrequencySpeed

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.

Parameter Specifications:
Airflow(m3/h): 18000
Power(Kw) : 1.1
Voltage/Frequency(V/Hz) : 380/50
Rated Electric Current(A) 2.8/4.5
Fan Type: Axle
Discharge Type : Down discharge
Controller Type : Intelligent LCD
Motor Type: Three-phase Fixed Speed

1.Automatic performance with LCD:Electronic control ,cleaning and water supplying antomaticly.
2.Energy-saving:lower daily cost ¿Cabout one kilowatt per hour.Uses 80% less energr-much more economical than comparable traditional air conditioner ¿C giving you tremendous savings.
3.Effectively and efficiently for cooling:5-12oC can be dropped in damp areas while 8-15 oC reduced in hot and dry conditions.
4.Great capacity of ventilation: Produces over 18000m3 of cooling power hour.Can cool areas up to 150m2 and can blow airflow as far as 30 merters away.
5.Environment: CFC Free, Nonpollution.
6.Option: Single phase various speed or three phase fixed and various speed.
7.Combinations of cooling,ventilation,air-exchange,anti-dust,and savor-removal.
8.Small investment but big effects:One workshop owning 100 sewing machines only needs about 6 units which costs 60% of the investment for traditional compressor air conditioners.All the investmens will be regained within 12 months.

Principle
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.

1- portable 2800
2-3500
3-5500
4-7500

State-of-the-art air coolers with different capacities, attractive designs, at competitive prices.

Main Features:
1.Combinations of cooling,ventilation,air-exchange,anti-dust,and savor-removal.
2.Environment: CFC Free, Nonpollution.
3.Automatic performance with LCD:Electronic control ,cleaning and water supplying antomaticly.
4.Energy-saving:lower daily cost Cabout one kilowatt per hour.Uses 80% less energr-much more economical than comparable traditional air conditioner C giving you tremendous savings.
5.Effectively and efficiently for cooling:5-12oC can be dropped in damp areas while 8-15 oC reduced in hot and dry conditions.
6.Great capacity of ventilation: Produces over 18000m3 of cooling power hour.Can cool areas up to 150m2 and can blow airflow as far as 30 merters away.
7.Option: Single phase various speed or three phase fixed and various speed.
8.Small investment but big effects:One workshop owning 100 sewing machines only needs about 6 units which costs 60% of the investment for traditional compressor air conditioners.All the investmens will be regained within 12 months.

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.

Parameter Specifications:
Airflow(m3/h):18000
Power(Kw) :1.1
Fan Type:Axle
Discharge Type :up
Controller Type :Intelligent LCD
Motor Type:Single-phase Various Frequency Speed
Voltage/Frequency(V/Hz) :380/50
Unit Size(mm):1080?1080?980

capability characteristic:
Injection shell is using modified PP composite materials and aluminum alloy column precision tectonic process; with the easy pull-out filters, wet screens paper of the frame protection and shockproof design, frame bearing capacity of 100 kg and above,with anti-corrosion, anti - ultraviolet, anti-aging15 years, high and low temperature resistance (subzero 20 fp C - 50 fp C) without distortion, and fuselage life for more than 10 years.
LCD panel control system, using single-phase various frequency speed, three-phase various speed, three-phase fixed speed intelligent electronic control systems and closed all high-quality match for the electrical, intelligent sewage cleaned regularly, wrong phase, short phase, overload current, water shortages protection and fault alarm function.
Adopt Sweden 5090-patented technology evaporative wet paper filter net , and the evaporative area in more than 85%; Using 3 leaves impeller, using silencers acoustic and noise reduction technology, the noise can be controlled lower than 56 dB

We're the leading manufacturer of Evaprotive Air Cooler in East China. The product will cool,ventilate, and change the air. Single unit can cool the area up to 130-150 square meters and 5-10 degrees will be reduced, but the comsumption of electric is 1.1kw. We supply 3 phase 380V fixed & variable speed motor and Single phase 220v variable frequency speed motor which is the newest. The product is suitable for the manufacturing place, waiting area, exhibition hall, studio space, internet service, foodcourt, kitchen , laundry, livestock breeding an so on. It can be mounted through window or wall. The direct drive with eletric oscillating louver enlarges the cooling area. Many rooms in one building can share the cool by using the duct like as a central air condtioning. The protrudent characteristics of our product are energy-saving,economy,pro-environment and safety. I believe it has the huge market potential in your country and also you can radiate to the perimeter zones. If possible,we will set up the assemble factory in the future.If you are intrested and want more, you are welcome to visit our website www.windking.net .
We are seeking a company who is reliable and capable for our agence in your country as our products are quite different from the disposable goods such as garments,shoes because besides the high quality, competitive price, we should supply the good after sales service. It's quite necessary that the partner we are expecting should own an engineering team which has experience and the sales network. We are expecting the cooperation with you.

Principle
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.


Parameter Specifications:
Airflow(m3/h): 18000
Power(Kw) : 1.1
Voltage/Frequency(V/Hz) : 220/50
Rated Electric Current(A) 2.8/4.8
Fan Type: Axle
Discharge Type : Down discharge
Controller Type : Intelligent LCD
Motor Type: Single-phase Various Frequency Speed

Capability Characteristic
Injection shell is using modified PP composite materials and aluminum alloy column precision tectonic process; with the easy pull-out filters, wet screens paper of the frame protection and shockproof design, frame bearing capacity of 100 kg and above,with anti-corrosion, anti - ultraviolet, anti-aging15 years, high and low temperature resistance (subzero 20 C - 50 C) without distortion, and fuselage life for more than 10 years.
LCD panel control system, using single-phase various frequency speed, three-phase various speed, three-phase fixed speed intelligent electronic control systems and closed all high-quality match for the electrical, intelligent sewage cleaned regularly, wrong phase, short phase, overload current, water shortages protection and fault alarm function.
Adopt Sweden 5090-patented technology evaporative wet paper filter net , and the evaporative area in more than 85%; Using 3 leaves impeller, using silencers acoustic and noise reduction technology, the noise can be controlled lower than 56 dB

The principle of temperature drop:
Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Parameter specification:
Airflow(m3/h):18000
Power(Kw) :1.1
Voltage/Frequency(V/Hz) :380/50
Fan Type:Axle
Motor Type:Three-phase Fixed Speed
Controller Type :Intelligent LCD

Capability characteristic:
Injection shell is using modified PP composite materials and aluminum alloy column precision tectonic process; with the easy pull-out filters, wet screens paper of the frame protection and shockproof design, frame bearing capacity of 100 kg and above,with anti-corrosion, anti - ultraviolet, anti-aging15 years, high and low temperature resistance (subzero 20 fp C - 50 fp C) without distortion, and fuselage life for more than 10 years.
LCD panel control system, using single-phase various frequency speed, three-phase various speed, three-phase fixed speed intelligent electronic control systems and closed all high-quality match for the electrical, intelligent sewage cleaned regularly, wrong phase, short phase, overload current, water shortages protection and fault alarm function.
Adopt Sweden 5090-patented technology evaporative wet paper filter net , and the evaporative area in more than 85%; Using 3 leaves impeller, using silencers acoustic and noise reduction technology, the noise can be controlled lower than 56 dB.

Airflow(m3/h): 18000
Power(Kw) : 1.1
Voltage/Frequency(V/Hz) : 220/50
Rated Electric Current(A) 2.8/4.8
Fan Type: Axle

Principle·ª
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.

JSA Exports is a leading provider of high-quality electric air cooler.

Based on the Hot Climate of India, we provide Big size, high efficient Air & Oil Cooler which increases the durability of the Compressor.

Benefits: Better Cooling & better compressor life

Principleú¦
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Parameter Specifications:
Airflow(m3/h): 18000
Power(Kw) : 1.1
Voltage/Frequency(V/Hz) : 380/50
Rated Electric Current(A)ú¦2.8/4.5
Fan Type: Axle
Discharge Type : Down discharge
Controller Type : Intelligent LCD

Principle
The principle of temperature drop: Water will absorb the heat from the hot air when steaming naturally. Its working principle: Extract wind through air blower, and the blower produces press, the air crosses the wet curtain, at the same time the water pump delivers water to the cloth water pipe on the wet curtain, and moisten the face of the whole wet curtain evenly, and the special angle of the wet curtain makes the water flow into one side where the air enters the wind directly, absorb a large amount of heat to lower the temperature through wet curtain, and filter it, which can make the wind nice, cool, moist and fresh. The water without evaporation falls back to the chassis forming waterway circulation. There are water level inductors on the chassis, when the water level lands to the fixed water level, it automatically open inlet valve to supply the source of water till the height of the booking water level, then close the inlet valve automatically.

Parameter Specifications:
Airflow(m3/h):18000
Power(Kw) :1.1
Fan Type:Axle
Discharge Type :up
Controller Type :Intelligent LCD
Motor Type:Three-phase Fixed Speed
Voltage/Frequency(V/Hz) :380/50
Unit Size(mm):1080?1080?980

Applicable scope
Manufacturing industries such as clothing , textile , the machinery , pottery , chemical industry , metallurgy , glass , five metals , leather ,etc.; Processing industry such as electroplating , electron , shoes-making , printing and dyeing , plastics , printing , packaged food; Stadium , school , waiting room , super market , laundry , kitchen , food market , underground parking , greenhouse, poultry , flowers , animal husbandry ,etc.

Average Power -0 0.5kw
Cooler Type - Chillers, Desert, Evaporator, Tower
Temperature - 40 Degree C

Expert Engineering Air Finned Cooler is unique in design. In which the Process liquid flows from the pot (as the direction shown in the fig. Expert engineering air cooler) and the cooling finned tubes and inserted in the pot, which cools the process liquid when it comes in contact with tube.

Cooling Finned Tubes:
* The tubes are consists of sealed stainless steel tubes with copper/aluminium fins around it

* It is filled with a liquid (the thermal transfer medium) appropriate to temperature of applications

Working Principle of Finned Tubes:
* It is filled with a liquid (the thermal transfer medium) appropriate to temperature of applications
* The working fluid evaporates extracting heat from the process liquid
Vapor moves towards fin side of the tube wherein it dissipates heat to the
ambient and condenses

* The condensed liquid comes back to the bottom condenses

* The cycle repeats

Reliability:
* Any equipment which depends on the reliability of other equipment is not reliable or less reliable

* Expert engineering's air finned cooler cools the product with natural draft
It does not have any moving parts, needs no external power source
Expert Engineering's air finned cooler does not depend on the cooling water there for risk of shut down due to poor quality/quantity of water is eliminated

Direct saving:
* Cost of Water: With Air Fin Coolers no water is required hence cost of water is saved.

* To get de sired amount of cooling normally for water-cooled heat exchange rs 40 to 50 lpm water is required. @ Rs 5 per cubic meter approxi mate saving will be about Rs. 110000/- pe r year.

* Cost of circulation of water: The energy spent in water circulation in is saved
On an average about 0.5kw of power is required for recirculation of water in each cooling circuit. @ Rs 4.5 per kw the power cost would be Rs 19710/-
* Preventive Miantenance: Water causes scaling problem, and due to scaling, temperature to the seal goes up, the pump needs to be taken for romoval of scale

* Cost of removal of scale and loss of production is saved with air fin coolers
Cost of each shut down is between Rs. 50000/- to Rs 150000/-(depends of criticality and cost of the product)

* Shut Down Maintenance: If seal fails because of poor cooling in addition to the Production and maintenance loss, cost fo replacement seal components add to the loss
* The cost incurred varies between Rs. 75000/- to Rs. 500000/- depending on the seal size and spares consumed

Industrial Air Cooler
Benefits of Air Cooler
- Adjustable air quantities to suit all weather conditions
- Les than 1/30 the cost of refrigerated air conditioning to run
- Oxygen Rich Fresh Air delivered to you
- All 100% fresh outside air
- A complete Natural process

BIG IN Cooling...SMALL IN COST!!

This mini portable air conditioner can use a battery to be taken outdoor.

This portable air cooler can be used also for your pets during summer.

You can use portable battery or just charge it via USB. It is very economic as the the electricity that uses is only 2.5 watt.

Measurements: 13.1*13.1*17cm

Weight: 650 g.

It has a water tank of 450ml that can be used for 4-6 hrs.

Use battery of bigger than 10,000 mAh.

Size(mm) - 590*340*1190

Weight - 14 Kg

Color - White

Number Of Controls( Speed and Function Switch) - 3 speed

Max Noise(1m - Low, High, Medium) - <65db

Air Delivery(m3/Hr) - 4,000

Air Throw (air velocity 0.5m/s) - 40ft

Fan Type ((Blade/Blower), Material and Grade) - Fan/ABS

Motor Wattage (W) - 107W

Fan motor RPM - 1,350

Swing Motor RPM - 3-5 rpm

Motor Winding - AI

Motor Class - B-Class

Inverter Compatability (Yes/No) - Yes

Fan Speed at Each Control Function(RPM) - 1350,1275,1200

Type Of Controller( Electronic Switch, PCB, Remote) - rotary Switch

Ice chamber - Yes

Water lable indicater - Yes

Water Float valve (Auto Fill) - Yes

Cooling Media - Honey comb/ Wood wool

Air/ Dust Filter - No

Swing 4 Way Defelection - Yes

Motorized Vertical Louvers movement - Yes

Size(mm) - 595*495*1148

Weight - 15.52 Kg

Color - White

Number Of Controls( Speed and Function Switch) - 3 speed

Max Noise(1m - Low, High, Medium) - <65db

Air Delivery(m3/Hr) - 4,200

Air Throw (air velocity 0.5m/s) - 40ft

Fan Type ((Blade/Blower), Material and Grade) - Fan/ABS

Motor Wattage (W) - 107W

Fan motor RPM - 1,350

Swing Motor RPM - 3-5 rpm

Motor Winding - AI

Motor Class - B-Class

Inverter Compatability (Yes/No) - Yes

Fan Speed at Each Control Function(RPM) - 1350,1275,1200

Type Of Controller( Electronic Switch, PCB, Remote) - rotary Switch

Ice chamber - Yes

Water lable indicater - Yes

Water Float valve (Auto Fill) - Yes

Cooling Media - Honey comb

Air/ Dust Filter - No

Swing 4 Way Defelection - Yes

Motorized Vertical Louvers movement - Yes

Size(mm) - 605*480*1040

Weight - 15.8 Kg

Color - White

Number Of Controls( Speed and Function Switch) - 3 speed

Max Noise(1m - Low, High, Medium) - <65db

Air Delivery(m3/Hr) - 4,500

Air Throw (air velocity 0.5m/s) - 40ft

Fan Type ((Blade/Blower), Material and Grade) - Fan/ABS

Motor Wattage (W) - 107W

Fan motor RPM - 1,350

Swing Motor RPM - 3-5 rpm

Motor Winding - AI

Motor Class - B-Class

Inverter Compatability (Yes/No) - Yes

Fan Speed at Each Control Function(RPM) - 1350,1275,1200

Type Of Controller( Electronic Switch, PCB, Remote) - rotary Switch

Ice chamber - No

Water lable indicater - Yes

Water Float valve (Auto Fill) - Yes

Cooling Media - Honey comb

Air/ Dust Filter - No

Swing 4 Way Defelection - Yes

Motorized Vertical Louvers movement - Yes

Expert Engineering Enhanced Air
Finned Cooler is unique in design. In which the Process Liquid flows from the
pot (as the direction shown in the fig. Expert Engineering Air Cooler) and the
cooling Finned Tubes and inserted in the pot, which cools the Process Liquid when it comes in contact with Tube


Cooling Finned Tubes.
The tubes are consists of sealed Stainless Steel tubes with Copper/Aluminium fins around it. It is filled with a liquid (the thermal transfer medium) appropriate to temperature of application.

Working Principle of Finned
Tubes It is filled with a liquid (the thermal transfer medium) appropriate to
temperature of application. The working fluid evaporates extracting
heat from the process liquid Vapor moves towards fin side of the tube
wherein it dissipates heat to the ambient and condenses.
The condensed liquid comes back to the bottom portion.
The cycle repeats,
BENEFITS OF AIR COOLER
Reliability:
Direct saving
Cost of Water: With Air Fin Coolers no water is required hence cost of water is saved.
To get desired amount of cooling normally for water-cooled heat exchangers 40 to 50
lpm water is required. @ Rs 5 per cubic meter approximate saving will be about Rs.
110000/- per year.
Cost of circulation of water: The energy spent in water circulation in is saved. On an average about 0.5kW of power is required for recirculation of water in each cooling circuit. @ Rs 4.5 per kw the power cost would be Rs.19710/-
Preventive Maintenance: Water causes scaling problem, and due to scaling, temperature to the seal goes up, the pump needs to be taken for removal of scale. Cost of removal of scale and loss of production is saved with Air Fin Coolers. Cost of each shut down is between Rs. 50,000/- to Rs. 1, 50,000/- (depends on criticality and cost of the product.)
Shut down Maintenance: If seal fails because of poor cooling in addition to the
production and maintenance loss, cost of replacement seal components add to the loss.
The cost incurred varies between Rs. 75,000/- to Rs. 5, 00,000/- depending on the seal size and spares consumed.
Indirect saving
Fouling: In absence of water, no scaling can take place. Because of scaling heat transfer gets reduced, hence either water consumption goes up or temperature in seal area goes up which reduces the seal life.
Better circulation of flushing fluid: In absence of coil, friction loss reduces hence there is better circulation of flushing liquid. The seal will be more comfortable with increased amount of flushing liquid, as there is no friction

Introduction:
Mechanical Seals generate heat and require lubrication while face sealing. Different API
Plans are used to dissipate this generated heat and cool the seal faces thus extending the seal life.
Flushing is required to cool and lubricate the seal. Controlling Flush Fluid Temperature is critical to the life of a mechanical seal. Cooling of the product also may be needed to improve the margin to vapour formation, to meet secondary sealing element temperature limits, to reduce coking or polymerizing, or to improve lubricity (as in hot water).

Disadvantage:
The basic disadvantages with water-based heat exchangers are the formation of scale around the tube due to fouling. Fouling can be very costly in refinery and petrochemical plants since it increases fuel usage, results in interrupted operation and production losses, and increases maintenance costs

Solution:
It has been often recommended to use the Air Cooler to get rid of the above problem but the size and the cooling efficiency of the so far developed air cooler had put them on the back foot and are rarely used for the cooling of the mechanical seals.
.
Expert Engineering has developed a new Enhanced Air Finned Cooler for such difficult applications, where no water is used. The compact size with natural draft cooling maintains the requirement of the cooling.

When comfort matters, Froza AC delivers professional air conditioning solutions designed for homes, offices, commercial buildings, and industrial spaces across Germany. Our mission is simple: provide reliable cooling systems that combine outstanding performance with energy efficiency while helping customers reduce electricity costs.

Product dimension - WxDxH (mm): 492 x 360 x 1044;
Colour: White-black and white-light blue;
Net weight (kg): 11.6;
Effective cooling area (m2): 30 - 40;
Airflow (the average result at the louver) (m3/h): 2300;
Water Tank Capacity (L): 40;
Power Capacity (W): 100;
Plug type: customized;
Control type: Electronic remote

The MISTEC MT-M602 is a portable evaporative cooler designed to improve comfort in large, well-ventilated industrial and commercial areas. Its 42-inch fan delivers airflow of up to 32,000 m3/h, while a 180-liter water tank supports mobile operation.

Variable speed control allows adjustment up to 580 RPM. The unit features a 1.5 HP motor and a 2 HP inverter. Standard power supply: 220 V, single phase; 50/60 Hz options are available.

Dimensions: 155 x 81 x 186 cm. Weight: 120 kg. Rated coverage is approximately 300 m2; actual cooling performance depends on temperature, humidity, ventilation, and installation conditions.

Applications include workshops, warehouses, production areas, and covered outdoor spaces with adequate ventilation.

Indicative EXW price: USD 2,800-4,000 per piece. The lower price depends on order quantity. Indicative price only. Final quotation depends on configuration, quantity, and delivery terms.

Airflow(m3/h): 18000
Power(Kw) : 1.1
Voltage/Frequency(V/Hz) : 220/50
Rated Electric Current(A) 2.8/4.8
Fan Type: Axle
Discharge Type : up discharge
Controller Type : Intelligent LCD
Motor Type: Single-phase Various Frequency Speed
Unit Size(mm):1080í-1080í-980

We supply specialized  manufactured Shell amp Tube Heat Exchangers amp Pressure Vessels Delivering superior quality products in minimum delivery time MOC we can supply in copper brass carbon steels stainless steels like SS304 SS310 SS316L copper alloys such as cupro nickel Admiralty amp Aluminum Brass and many other materials We can supply Heat Exchangers amp Pressure Vessels up to 40 Tons
The product range includes the proprietary plate fin tube heat exchanger oil coolers inter coolers after coolers marine heat exchangers oil cooling systems condensers chillers economizers super feed heat exchangers receivers and surge drums
This products are extensively used in oil and gas refineries air separation plants chemical steel refineries pharmaceutical industries air conditioning amprefrigeration plants heat treatment shops marine engines amp gear boxes induction furnaces machine tools diesel engine generating sets compressors power plant installations transformers hydraulic power packs food processing vegetable oil refining amp sugar industry etc
We are supplying this with certifications such as U R amp NB Stamp from ASME ISO 90012008 quality certificates from LRQ  and certifications from DGQA IRS NSIC etc
This are all manufactured in Nondestructive testing such as
Visual Inspection
Liquid penetrant testing
Radiographic testing
Tube to Tube sheet Weld radiography
Ultrasonic testing for raw material and welds
Helium leak testing
Bubble Leak testing
Magnetic particle testing

Aluminium brazed radiators, charge-air coolers and condensers for passenger cars, LCVs, tractors and gensets. Helium leak-tested, pressure-cycle tested; plastic or aluminium tanks. OE-fit applications and custom industrial sizes. MOQ 20 pcs.
Aluminium Brazed Radiators and Intercoolers are heat-exchange components manufactured using aluminium cores and brazed joints to provide efficient thermal transfer and compact construction. Radiators help dissipate engine coolant heat, while intercoolers reduce the temperature of compressed intake air in turbocharged or supercharged engines. These components are used in passenger vehicles, commercial trucks, buses, agricultural machinery, construction equipment, and industrial engine systems. Available in different core dimensions, fin configurations, tube designs, and mounting arrangements, they can be specified for particular engine and operating requirements. Buyers should confirm compatibility, pressure ratings, cooling capacity, and connection dimensions before ordering.

Air-Cooled Water-Cooled Drum Cooler Machine
The Foundry Sand Drum Cooler by Guoning is a high-performance cooling solution designed for sand treatment in lost foam castingâ??and other foundry processes. This equipment rapidly cools hot recycled sand to a controlled temperature, ensuring consistent sand quality for reuse. With a combination of water cooling and air cooling, and automatic sand flow and temperature regulation via PLC, it delivers stable performance while minimizing manual operation.
This drum cooler is ideal for foundries seeking to enhance production efficiency, reduce energy consumption, and maintain the quality of recycled sand throughout the casting process.
Main technical parameters
Overall dimensions: 8200*2000*2250mm;
Power requirements: AC power with a rated frequency of 50Hz and a rated voltage of 380V (deviation ± 5%);
Power: 15KW+0.75KW Ã?1;

Shell steel plate thickness: 4mm, 10mm Bottom channel steel: 20 # channel steel;

Transmission method: gear transmission;
The bearing seat is made of cast steel to enhance strength;
Conveying capacity: � 7.5m ³/ h (20-40 quartz sand or pearl sand);
Drum speed: Drum speed: 5-15r/min
Cooling water consumption: 50-100 m ³/ h;
Fan model: SF NO4-4; Air volume: 9300m3/h; Power: 0.75KW.
Product structure
Horizontal cooling outer box: one set;
Horizontal cooling inner drum: one set;
Gear drive;
Drive device: one set;
Water-cooling system.
Working Principle
Hot recycled sand enters the drum from the feeding hopper. As the drum rotates, the spiral lines lift and transport the sand, allowing air and water to efficiently absorb heat. An axial flow fan directs airflow from the sand outlet into the drum, guiding heat and dust toward the exhaust. The hot air passes through a cyclone dust collector, which removes dust before clean air is discharged. Water pipes spray both the inside and outside of the drum, providing rapid cooling and ensuring sand reaches the desired temperature efficiently. A blocking wheel system prevents excessive axial force, ensuring safe and stable operation.

Using Air Conditioning style clothing uses the mechanism called "physiological cooler" to let air taken in from the fan flow between the body and the uniform, and cool the body by the heat of vaporization when sweat evaporates, making it cool and comfortable.

- Rechargeable
- Reduce Exhausted
- Cooling Wear

*Features:

- Best Engineering Plastic Injection
- Molding Body
- UV - Resistant Cabinet Material
- 100% Usable in Outdoor

*Best high torque motor

- 100% maintenance free
- 100% dust & moisture proof
- Serves upto 80% Electricity Bill
- Can be used non stop up 24 Hrs.

*How it works?

Evaporative cooling is a physical phenomenon in which evaporation of a liquid, typically into surrounding air, cools an object or a liquid in contact with it. Latent heat describes the amount of heat that is needed to evaporate the liquid; this heat comes from the liquid itself and the surrounding gas and surfaces. When considering water evaporating into air, the wet-bulb temperature, as compared to the air\'s dry bulb temperature, is a measure of the potential for evaporative cooling.

The greater the difference between the two temperatures, the better the evaporative cooling effects. When the temperatures are the same, no net evaporation of water in air occurs, thus there is no cooling.

*Applications :

- Plant or Factory
- Leather Industries
- Showroom
- Farm House
- Canteen
- Warehouse
- Prining Press
- School, Colleges, Office
- Plasic Moulding Industry
- Iron Industry
- Engineering Industrial
- Electronics Industry
- Hotel & Restaurant
- Paper Industries
- Textile Industries

*Extraordinary features & benefits of BlowTech Air Washer Unit

-5090 Honey Comb - Cellulose Wet Pad# World\'s Best Quality Pads imported from Finland with Anti Bacterial Resins & 4X Longer Life than
any other Pad (last upto 5 yrs.*)

4D Technology (Top & Bottom Discharge)
- BLOWTECH is the only brand which gives 4D Cooler in movable & ductable Coolers.

Turbo Axial Fan#
- BLOWTECH is the only brand which gives Turbo Axial Fan for worlds most powerful air through & very low noise

* Specification:
Product Name: Vietnam Palm Sugar / Palmyra Jaggery
Material: 100% Palm Sap (from Palmyra Tree)
Form: Block / Powder / Granule (as requested)
Color: Golden Brown to Dark Brown
Taste & Aroma: Mild sweetness with natural caramel flavor
Brix: 78 to 82
Purity (Sucrose Content): 85 to 95%
ICUMSA: 8,000 to 12,000 IU
Moisture: Max 5%
Ash Content: Max 2%
Shelf Life: 18 to 24 Months (store in a cool and dry place)
Ingredients: 100% Evaporated Palm Sap
Usage: Suitable for cooking, baking, beverages, sauces, confectionery, and Asian recipes
Origin: Vietnam
Packing: Packed in food-grade PE inner bags, then in strong carton boxes; custom packaging available upon request
Delivery: Shipment available by sea, air, or express depending on customer preference
MOQ: 1000 kg (negotiable)
Port of Loading: Ho Chi Minh Port, Vietnam
Payment Terms: T/T, L/C, or as agreed with buyer

Type: Copper Wire
Material: Copper
Shape: Linear
Color: Red
Purity:99.9% Min
Application:Air Condition or Refrigerator, Water Tube, Water Heater, Oil Cooler Pipe
We could supply the copper scrap with high quality and competitive price.
1) Our copper scrap includes wires, tubes, and plates, etc.
2)The size is chips or other.
3) Copper content could meet customers need.
Application:
Electrical, light industry, machinery,national defense industry .
Copper Scrap is industry a important sources of the raw materials, all kinds of can be recycled Recycling waste production with copper
We could supply the copper scrap with high quality and competitive price.
1) Our copper scrap includes wires, tubes, and plates, etc.
2)The size is chips or other.
3) Copper content could meet customers need.
Application:
Electrical, light industry, machinery,national defense industry .
Copper Scrap is industry a important sources of the raw materials, all kinds of can be recycled Recycling waste production with copper Electric wire, cable, brushes, special electric spark electrical products, terminal printing electrical road board, wire with a bronze belt, air cushion cover, converge-wires terminals electrical, light industry, machinery, building industry, national defense industry copper scrap is industry a important sources of the raw materials all kinds of can be recycled recycling waste production with copper

The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit.

Operation principle:
Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency.

Technical data:
Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden
Type: ECO 5000 VS-HP, R407C
Year made: 2003
Evaporation capacity: 5000 liters / 24 hour (pure water)
Electricity consump.: about 0,15 kWh / liter pure wateri)
Control unit: Siemens Micromaster 420
Compressor: Bitzer Kuhlmachinenbau GmbH,
Compressor type: 6G-40,2
Compressor capacity: 126.8 m3/h, 19/28 bar
Refrigenerant: R 407 C
Main dimensions: 2.8 m x 1.3 m x 2.9 m
Weight: 1500 kg.

The MISTEC MT-FJDC series of HVLS wall fans provides high-volume air circulation for industrial and commercial spaces. Wall mounting keeps floor space clear and offers a practical ventilation solution for warehouses, factories, gyms, and exhibition halls.

Available diameters: 0.9 m, 1.2 m, 1.5 m, and 2.0 m. Model specifications:
MT-FJDC-90: 0.9 m diameter, 450 m3/min airflow, 0.2 kW, 20 kg.
MT-FJDC-120: 1.2 m diameter, 720 m3/min airflow, 0.4 kW, 25 kg.
MT-FJDC-150: 1.5 m diameter, 900 m3/min airflow, 0.75 kW, 35 kg.
MT-FJDC-200: 2.0 m diameter, 1,250 m3/min airflow, 1.1 kW, 42 kg.

Features include a permanent magnet synchronous motor, 160-degree oscillation, multiple speed settings, aluminum alloy blades, a heavy duty steel mounting bracket, and overload protection. IP55 protection supports use in suitable industrial environments. Installation options are available for steel and concrete walls.

Electrical options: 220 V or 380 V. Confirm model, voltage, mounting requirements, and available control options when requesting a quotation. Actual airflow coverage depends on site layout and installation conditions.

Indicative EXW price: USD 980-1,400 per piece. The lower price depends on order quantity. Final quotation depends on the selected size, configuration, quantity, and delivery terms.

350 W

220-240 V Ac,50/60hz

Class-i

500w

220-240 V Ac,50/60hz

Class-i

500w

Hybrid Motor

220-240 V Ac,50/60hz

Class-i

750w

Hybrid Motor

220-240 V Ac,50/60hz

Class-i

750w

Copper Motor

220-240 V Ac,50/60hz

Class-i

Pellet coolers are used to reduce the hot pellets coming out of the pellet press to the ambient temperature. The waiting time of the pellet in the cooler is controlled by adjustable level sensors on the cooler. By the temperature sensors at the pellet cooler outlet, the pellet feed temperature is seen at the machine discharge. By the distributor system at the inlet of the pellet cooler, evenly cooling is captured at every point by ensuring a homogeneous distribution and product height within the cooler. The feed dust in the hot air going to the aspiration unit is sent back to the system by the aspiration cyclone. After cooling, the pellets hardens and dust formation is prevented during packaging.
The moisture is reduced to extend the shelf life of the pellets.
Single or double-deck models are available depending on the intended use

GENERAL FEATURES:
Lower body side sheets are specially designed for fresh air intake
The lower grate can be driven by motor, pneumatic or hydraulic
The lower grate is designed to allow air entry
Body sheets have bolt and nut connections for easy assembly/disassembly

We, FITZER are amongst the prominent Supplier & Exporter of a comprehensive range of Indian Spices, Dehydrated Food Product and Seasonings Masala. As exporter of world-class spices, we understand the need for the highest standards of quality and regulatory requirements which includes flawless packaging.

Product Specification
Packaging Size 25 Kg
Form Powder
Packaging Type PP Bag and Box
Variety of Turmeric Available Salem, Rajapore
Is It FSSAI Certified FSSAI Certified
Shelf Life 8 Months
Usage/Application Food, Cosmetic, medicine Industry
Country of Origin Made in India

In any Power plant running on steam, the purity of boiler feed water and steam is absolutely crucial; especially to steam turbine, steam boiler, super heater, condenser, and other steam equipment. To prevent damage to a steam turbine, steam boiler, and other equipment due to scaling and corrosion, on-line steam and water analysis of critical parameters such as pH, Conductivity, Dissolved Oxygen, Silica, Sodium, Hydrazine and Phosphate, etc is a must. Steam can be as hot as 560�°C. Pressures can be as high as 250 bar. To keep the power plant up and running with minimum erosion and corrosion of the steam turbine, steam boiler, and condenser, we have developed a fully integrated Steam and Water Analysis System (SWAS) that provides exact, precise measurements on all these critical parameters. Samples are at high temperature & pressure. Sample conditioning is required to bring down the temperature & pressure at the desired level.

Product Description
The Multi-Disc Screw Dehydrator is a reliable and versatile dewatering technology that allows treatment of many sludge type and it is suitable for a variety of applications. High oil and fat materials for instance tend to easily plug up belt press filters, which drastically increases their maintenance requirements and operating costs. Centrifuges on the other hand require immense power to work effectively.

With the new Screw Dehydrator technology customers finally have an efficient solution that addresses their operational needs:
Sludge from processed flow-back water from oil and gas operations
DAF sludge from livestock waste or meat processing operations
Municipal sewage and wastewater treatment processes
Food and beverage processing waste treatment
Sewage sludge from remote camp operations
Sludge from biological treatment processes

Stainless Steel corrugated flexible hoses are offered from size 6mm NB (1/4") to Size: 200mm NB (8'), The Annular Corrugated hose body provided the flexibility & pressure tight core of the assembly, We also manufacture high flexible close-pitch hoses for special applications.

BRADING

When pressure is applied, unbraided corrugated hose tends to elongate axially. To restrain this, a external layer of S.S. wire braid is provided. The braid also makes the assembly pressure resistant.

Sometimes two or even three layers of braiding are provide for high pressure applications. The braiding is highly flexible & follows the movement of the hose. The braid is normally manufactured in S.S. 304 Wire, how ever S.S. 316 & S.S. 321 braid can also be manufactured. We also supply wire braid in different configurations as per customer specifications.BRADING

When pressure is applied, unbraided corrugated hose tends to elongate axially. To restrain this, a external layer of S.S. wire braid is provided. The braid also makes the assembly pressure resistant.

Sometimes two or even three layers of braiding are provide for high pressure applications. The braiding is highly flexible & follows the movement of the hose. The braid is normally manufactured in S.S. 304 Wire, how ever S.S. 316 & S.S. 321 braid can also be manufactured. We also supply wire braid in different configurations as per customer specifications.

ADVANTAGES OF S S FLEXIBLE HOSES

High physical strength combined with light weight.
Suitable for wide temperature range (-270oC to 700oC)
Good corrosion resistance. Resistance to fire, moisture, abrasion & penetration.
Absorbs vibration and noise from pumps, compressors, engines etc.
Compensates for thermal expansion or contraction of piping.
Correct problems of misalignment.
A flexible & quick alternative for rigid piping in difficult locations.
APPLICATIONS OF S S FLEXIBLE HOSES

Refineries
Power Plants
Steel Plant
Nuclear Installations
Fertilizer Industry
Pharmaceutical Industry
Cryogenic Service
Chemical Industry
Boilers
Paper Plants
Lubrication Systems
Automotive Industry
Steam, Hot Water
Pneumatic Service
Ports & Ship Yards
Defence Industry
Piping
Vibration Absorption
Railways

We take immense pleasure to introduce ourselves as a trusted and reputed manufacturer and supplier of Square Cooling Tower. It is used in power plant, chemical, pharmaceutical and petrochemical industry as heat exchanger. The main aim of the tower is to reduce the temperature of water by bringing air and water into direct contact with each other. To manufacture this tower our dexterous workforce uses finest quality FRPs. Square Cooling Tower comes in different sizes and specifications as per the requirements of clients.

Features:

Resistant to corrosion
Low power consumption
Generate low noise


Range from 15 TR to 1500 TR in single cell & capacity can be increased further by Multi-cell cascade.

Full FRP Body
Structure available in both MS HDG and FRP Pultruded Profile.
Water distribution: PVC with FRP Lining.
High space efficient.
Inspection window is Provided.
Very low drift loss
Easy to Maintain.
Part load operation is available.

We are emerging as one of the fastest growing companies engaged in manufacturing and supplying FRP Induced Draft Square Cooling Tower. It is made of axial flow fan, casing, fills, basin, and other mechanism that make its functioning outstanding. The tower is designed with excellent heat transfer and uniform water distribution function. Housing of the tower is made of tough FRP to ensure its ability to withstand adverse weather condition. It is installed on concreted & cemented pillars to guarantee strong stability. The FRP Induced Draft Square Cooling Tower is ideal for breweries & distilleries plants, oil refineries and glass manufacturing plant.

Features:

Low noise generation
Easy and convenient installation
Robust construction

MOC : SS316L, SS316, SS304, MS, PP, UPVC
Line Size : 1/4³ NB to 20³ NB
Connection Type : BSP(F), NPT(F) Threads, Flanged 150#, Table E, Table F
Hydro Test Pre. : upto 100 kg/cm2
Design : Customised (as per customerâ??s requirement)
Valves : 3-Way Ball Valve, Butterfly Valve with Tee

APPLICATION:
Water, DM Water, Waster Water
Paints & Inks
Solvent
Oil
Coolant Filtration
Pharmaceuticals
Process Chemicals
Resins & Adhesive

FEATURES:
High Flow Rate
High Dirt Holding Capacity
Easy to Clean
Easy to Operate
Customized Design
Various Type of Filter Bags
High Pressure Housings
Low Maintenance