Model V158TIL Engine type 4 cycle, V type, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 680(500)/2,300 Displacement( cc ) 14,618 Cylinder number - bore x stroke( mm ) 8 - 128x 142 Mean piston speed (m/sec. ) 10.89 Compression ratio 14.6 : 1 Firing order 1 â?? 5 â?? 7 â?? 2 â?? 6 â?? 3 â?? 4 â?? 8 Governor type of injection pump Mechanical variable speed (R.Q.V) Fuel consumption lit / h 130 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.6 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 200 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 89 / 78 Fresh water pump type Centrifugal type, driven by belt Sea water pump type Bronze impeller type driven by belt Direction of revolution Crankshaft Counter clockwise viewed from stern side Engine size (L x W x H) (mm) 1,657 x 1,226 x 1,397 Engine dry weight (KG) 1,435
Model V158TIM Engine type 4 cycle, V type, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 540(397)/2,100 Displacement( cc ) 14,618 Cylinder number - bore x stroke( mm ) 8 - 128x 142 Mean piston speed (m/sec. ) 9.94 Compression ratio 15 : 1 Firing order 1 â?? 5 â?? 7 â?? 2 â?? 6 â?? 3 â?? 4 â?? 8 Governor type of injection pump Mechanical variable speed (R.Q.V) Fuel consumption lit / h 100 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.6 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 200 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 89 / 78 Fresh water pump type Centrifugal type, driven by belt Sea water pump type Bronze impeller type driven by belt Direction of revolution Crankshaft Counter clockwise viewed from stern side Engine size (L x W x H) (mm) 1,657 x 1,226 x 1,397 Engine dry weight (KG) 1,350
Model V158TIH Engine type 4 cycle, V type, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 480(353)/1,800 Displacement( cc ) 14,618 Cylinder number - bore x stroke( mm ) 8 - 128x 142 Mean piston speed (m/sec. ) 8.52 Compression ratio 15 : 1 Firing order 1 â?? 5 â?? 7 â?? 2 â?? 6 â?? 3 â?? 4 â?? 8 Governor type of injection pump Mechanical variable speed (R.Q.V) Fuel consumption lit / h 85 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.6 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 200 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 89 / 78 Fresh water pump type Centrifugal type, driven by belt Sea water pump type Bronze impeller type driven by belt Direction of revolution Crankshaft Counter clockwise viewed from stern side Engine size (L x W x H) (mm) 1,657 x 1,226 x 1,397 Engine dry weight (KG) 1,350
Rack Lithium Battery Designed with reliability and efficiency in mind, rack mounted lithium batteries provide uninterrupted power for your servers and critical systems. With their compact design and optimized energy density, our server rack batteries integrate seamlessly into your existing setup, ensuring maximum uptime and preventing power outages. Deliver the power and reliability your business needs to keep your operations running smoothly and protect your valuable data with server rack batteries. Core technology strength of rack mounted lithium battery Energyland is constantly pursuing breakthroughs in battery performance, putting lithium batteries with higher capacity, higher safety, smaller size and longer life into lithium battery racks, fully integrating excellent performance with compactness and flexibility, with absolute advantages in size, layout, operation and maintenance, cost, etc., so as to make lithium batteries more widely used and to provide more choices, such as battery management systems. lifepO4 battery racks are available for customers with different needs.
Lithium battery powered Rail bolt wrench machine (model: LJ-LDB171X) is composed of host, control system, battery system and rail traveling part. The utility model has the advantages of compact structure, light weight, flexible assembly and disassembly, convenient use and no exhaust emission. It can be transported separately, which is convenient for single person to carry on site. The weight of the separated part is less than 15kg. It is applicable to the laying, maintenance and emergency rescue of railway, and is specialized in various railway bolt operations Specification Model NGM-4.4II Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 1480*470*810mm Engine Two-stroke petrol engine/4.4KW Main shaft rpm 4670r/min Bolt screwing flat grinding wheel 125*65*M20 Grinding head angle of inclination 90 ° Grinding head stroke 45 mm Total weight 61kg
Lithium battery powered Rail bolt wrench machine (model: LJ-LDB171X) is composed of host, control system, battery system and rail traveling part. The utility model has the advantages of compact structure, light weight, flexible assembly and disassembly, convenient use and no exhaust emission. It can be transported separately, which is convenient for single person to carry on site. The weight of the separated part is less than 15kg. It is applicable to the laying, maintenance and emergency rescue of railway, and is specialized in various railway bolt operations Specification Model LJ-LDB1701X Type Lithium Battery Torque Wrench Material Stainless Steel Dimensions (L x W x H) (mm) 1100*700*450mm Type Battery powered rail bolt wrench Rated voltage (DCV) 24-48 Max. torque 3000 N.m Motor speed (RPM) 0-3000 optional Impact frequency (BPM) 0-5000 optional Battery pack capacity (ah) 24-48 Operating temperature range (-40 ~ 50 â??) Operating range m6-m30 Torque control adjustable and controllable Weight 22kg
expertbinocular * com Product Info for Kenko Lens2scope Adapter for Nikon F Mount (Angled View) Kenko black Lens2scope Adapter for Nikon F Mount is a simple accessory that converts any Nikon F Mount lens into a spotting scope. Its lightweight body houses a compact roof prism, lenses, and an eyepiece just like a traditional spotting scope and with the lens is attached, the whole system acts as a spotting scope. This model features an angled eyepiece that is set at a 45�° angle for more comfortable viewing while sitting, standing or laying. Kenko K-LS10-NFAB Specs Prism System Roof prism Focal Length 10 mm Apparent Field of View 42�° Eye Relief 20 mm Dimensions 7.1 x 4.3 x 3.1" / 18.0 x 11.0 x 8.0 cm Weight 6.5 oz / 185.0 g Packaging Info Package Weight 0.635 lb Box Dimensions (LxWxH) 6.1 x 4.35 x 3.5"
Starting a livestock feed pellet factory has been a profitable business activity in many countries. The production line of the livestock feed pellet factory specializes in producing pig feed, horse feed, cattle feed, sheep feed, donkey feed, rabbit feed, etc. How to make livestock feed? You need livestock feed pellet plant equipment first. Our livestock feeds pellet mill production line with output ranging from 1 t/h to 100 t/h. A complete livestock feed pellet plant includes raw material storage, a cleaning machine, a feed crusher, a feed mixer, a livestock feed pelletizer, a cooler, a screening machine, a packaging system, transportation, and an electronic control system. Our feed pellet production line can produce 2-12mm cylindrical feed pellets according to your needs. At the same time, the livestock feed production plant has the characteristics of low energy consumption, high production efficiency, and large profits. It is especially suitable for large feed mills, breeding farms, large farms, etc. We provide free installation, training, factory design, and timely after-sales service.
Starting a poultry feed processing plant has always been a profitable business in many countries. Poultry feed plant specializes in producing duck feed, goose feed, chicken feed, bird feed, parrot feed, and other poultry feed, etc. How to make poultry feed? You need a poultry feed pellet production line first. Our fully automatic poultry feed mill plant with output ranging from 1ton/h-100ton/h. The complete poultry feed pellet production line includes raw material storage, a washing machine, a feed crusher, a feed mixer, a poultry feed pelleting machine, a cooler, a screening machine, a packaging system, transportation, and electronic control system. The poultry feeds pellet plant has good raw material versatility and can be used for the granulation of various raw materials such as corn, sorghum, wheat, beans, and oilseed meal. At the same time, the poultry feed production plant has the characteristics of low energy consumption, high production efficiency, and large profits. It is especially suitable for large feed mills, breeding farms, large farms, etc. At the same time, we provide free installation, training, factory design, and timely after-sales service.
Technical Parameters Travel of X and Y Axes: 250x300 mm; Maximum cutting thickness: 350 mm; Maximum Work piece weight: 200 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 340x500x350 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 1.2 KVA; Approx. Machine size (LxWxH): 1480x1010x1400 mm; Approx. Machine weight: 1050 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
Hydrolysis cleaning system refers to a cleaning process that utilizes the chemical reaction of hydrolysis to break down & remove polymer from surfaces or equipment. This system is commonly used in industrial settings, such as in the cleaning of heat exchangers, boilers, condensers, filtration elements and other equipment that may accumulate deposits. The principle of Vacuum cleaning furnace is based on the property that high molecule of synthetic fiber, isolated from air, is to be molten when the temperature reaches up to 300�?C, then melt polymers flow into waste collecting tank; when the temperature increases to 350�?C, up to 500�?C, polymer starts to degrade and exhaust out of furnace. TEG cleaning furnace: It uses the principle that polyester can be dissolved by glycerol (TEG) at its boiling point (at normal pressure, it is 285�°C) to achieve the purpose of cleaning. Ultrasonic cleaner: it is a device that emits vigorous mechanical vibrations into a liquid bath. This device achieves cleaning purposes through the use of sound waves. The sound waves create cavitations through the movement of the liquid bath, resulting in a detergent effect on the surface of the item being cleaned. It releases energy up to a level of 15,000 psi in order to loosen and eliminate dirt, grime, and impurities.
XC700 DC 96V Motor Controller for Solar Pumping System XC700 motor controller is mature product designed for solar pumping system. This product was released several years ago, the performance and reliability had been verified and approved by clients and market, it's one of the best sellers in XC motor control product family. Demand on solar pump controller could be diverse, we provide bespoke service for customers. If you have any specific requirement, we help you achieve it. This motor controller for solar pump comes with characteristics: Specification: Model: XC700-SP-96V-1300w Working Voltage: DC24-150V Rated Voltage: 96V Rated Current: 13.5A Working Temp: -30-85 Humidity: 95% Max Dimension: 115*96*39mm (PCBA), 144*170*61mm (set) Protection: Antiflood protection, water lack protection, undervoltage protection, overcurrent short circuit protection, over-temperature protection, motor stall protection and reverse, polarity protection Start/stop and speed control Suitable for applications powered by solar panels, MPPT algorithm inside XC Motor Control has been specializing in motor control since2011, we have considerable expertise in enhancing motor control. The potent combination of hardware and advanced software can keep your device working at its best. Have a try, you are worth a better solution.
Technical Parameters Travel of X and Y Axes: 1000x1200 mm; Maximum cutting thickness: Standard: 800 (Can be adjustable) mm; Maximum Work piece weight: 2000 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm. mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 1010Ã??1500 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 100 square mm/min; Wire speed: 11.5 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 1.2 KVA; Approx. Machine size (LxWxH): 3100x2500x2300 mm; Approx. Machine weight: 5000 kg; Approx. Machine control cabinet size: 1200x800x800 mm; Approx. Machine control cabinet weight: 150 kg.
Technical Parameters Travel of X and Y Axes: 630x800 mm; Maximum cutting thickness: 600/800 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 680x1080x600 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 2265x1865x1980 mm; Approx. Machine weight: 3500 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
DK7745 Technical Parameters Travel of X and Y Axes: 450x550 mm; Maximum cutting thickness: 460 mm; Maximum Work piece weight: 750 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 500x750x460 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1865x1350x1900 mm; Approx. Machine weight: 1250 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
Technical Parameters Travel of X and Y Axes: 400x500 mm; Maximum cutting thickness: 460 mm; Maximum Work piece weight: 450 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 460x690x460 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1600x1240x1400 mm; Approx. Machine weight: 1250 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
Technical Parameters Travel of X and Y Axes: 350x450 mm; Maximum cutting thickness: 460 mm; Maximum Work piece weight: 300 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 400x650x460 mm; Surface Roughness /Ra: Ra less than 2.5 u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function ; Total machine power: 1.8 KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001 mm; Pulse width adjustable range: 15-150 us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1200x1170x1400 mm; Approx. Machine weight: 1440 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg.
Technical Parameters Travel of X and Y Axes: 320x400mm; Maximum cutting thickness: 400 mm; Maximum Work piece weight: 300 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 360x610x400mm; Surface Roughness /Ra: Ra less than 2.5u.m; Numerical Control System: X8, HF SYSTEM ; Display: Latest Version Serial Interfaces: USB port, RS 232C port, Ethernet port ; Remote control: With the function 3-D Graphical Preview: With the function; Total machine power: 1.8KV; Machining precision/Processing precision: 0.015 mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; Maximum cutting speed: 150 square mm/min; Wire speed: 11 m/s; Minimum feed increment: 0.001mm; Pulse width adjustable range: 15-150us; Maximum power consumption: less than 2 KVA; Approx. Machine size (LxWxH): 1200x1170x1400mm; Approx. Machine weight: 1150kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80kg.
expertbinocular*com Kenko Lens2scope Adapter for Nikon F Mount (Straight View) Price:$99.99 SKU:EB-861613155 Brand:Nikon Availability:In Stock Shipping:Calculated at checkout Product Description Product Info for Kenko Lens2scope Adapter for Nikon F Mount (Straight View) Kenko black Lens2scope Adapter for Nikon F Mount is a simple accessory that converts any Nikon F Mount lens into a spotting scope. Its lightweight body houses a compact roof prism, lenses, and an eyepiece just like a traditional spotting scope and with the lens is attached, the whole system acts as a spotting scope. This model sets the eyepiece in-line with the lens for faster and easier target acquisition and tracking. Kenko K-LS10-NFSB Specs Prism System Roof prism Focal Length 10 mm Apparent Field of View 42�° Eye Relief 20 mm Dimensions 7.1 x 3.5 x 3.1" / 18.0 x 9.0 x 8.0 cm Weight 6.5 oz / 185.0 g Packaging Info Package Weight 0.7 lb Box Dimensions (LxWxH) 6 x 4.4 x 3.5"
Product Description Our Platinum TwinDrag two-speed reels are simply the finest built and most rigorously tested offshore reels available to serious big-game fisherman. Designed to be light weight yet extremely durable, they offer state-of-the-art technology not found in other reels. Complementing the reel's ultra-smooth and highly efficient TwinDrag system is a unique, graduated alphanumeric visual reference scale that works in conjunction with the preset lever to enable precise drag range settings. That in conjunction with the reel's two-speed Quick-Shift, which allows for an easy transition between high and low gears, gives anglers a decided advantage when fighting powerful fish like big wahoo, tuna and marlin. Unhindered free spool at every drag setting Heat treated pinion gears Patented TwinDrag system Stainless Steel gears Stainless Steel Springs and Clips Removable Spool stud 2 Stainless Steel anti-reverse dogs 7 Abec rated Stainless Steel bearings sealed with teflon impregnation Accudrags Harness lugs ATD Reel Bag One year warranty
