Rhodium Rose Gold Plated Diamond Rings Suppliers and Manufacturers

Product Code Product Description PRS-CMTC03 Mortar Permeability Tester ( 3 Unit ) This method of test covers the procedure for determining the permeability to water of the pozzolana mortar prepared and cured under specified conditions, by measuring the percolation of water through Standard cylindrical specimens. The permeability unit shall consist of a specimen container ring of 100 mm diameter and 50 mm high, held between a bottom plate and a water cell. The hydraulic head for testing shall be obtained by connecting the unit to a compressor through a water pressure vessel. A pressure regulator and pressure gauge shall be included between the compressor and the water pressure vessel to indicate the test pressure. Water percolating through the specimen shall be collected in a container. Typical details of an individual unit are given in fig. 6 and 7. The water cell shall be 100 mm diameter brass cylinder and the top and bottom plates shall be either of brass or any other non-corroding metal. The connecting pipeline from the water cell to the water pressure vessel shall also be of non-corroding metal or of hard board polythene. This requirement is necessary since the tests last over a number of days in which mild steel or similar materials will get corroded and the rust formed will coat the top of the specimens and affect the permeability. The connection of units to the air cylinder shall be done with armoured heawy-duty rubber hose.

Ti-Al Target Cr Rotating Target Si-Al Rotating Target;Product maximum size of Ï?500 * 2000, grain size â?¤100μm, density â?¥98%, purity â?¥99.5%. Silicon Target Cr-Al Target Titanium Aluminum Alloy Targets ZrO2 Target;Purity (%) Density (g/cm3) Shape & Size 99.9 5.56 Circular Φ18~30x7~18mm Sector Plate TiO2 Target; Purity(%) Density(g/cm3) Shape & Size 99.9 4.24 Circular Ф50~90x8~12mm Ta2O5 Targets SiO2 Target;Purity(%) Density (g/cm3) Shape & Size 99.9 2.21 Circular Φ18~30x7~18mm Ring Φ230~350x5~20mm Plate MgO Target;Purity(%) Density(g/cm3) Shape & Size 99.9 3.58 Circular Ф50~90x8~12mm Al2O3 Target; Purity(%) Density(g/cm3) Shape & Size 99.99 3.99 Circular Ф50~90x8~12mm

Harness Probe Pogo Pin CHZ136-H(8.4) for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHZ136 harness probe we will introduce here is 1.36 mm in diameter and 33.4 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of nickel-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.3 mm at most when this probe works, although the plunger can move as far as 6.4 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.3 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating:   3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 113 ±33 gf (4 oz) @ load 4.3 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Ni Plated Spring: SW-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. �?�  Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Superfine needle tip wire pen cable for universal digital multimeter, safety grade 1000V 10A 20A multimeter lead probe, super-pointed multimeter lead probe pen for mobile phone logic board repair tool. 1000V 20A /10A Universal Superfine Lead Probe Needle Tip Wire Pen Cable For Digital Multimeter [ Optional Types ] : Option 1: 1000V 10A Superfine Needle Tip, Gold Option 2: 1000V 20A Superfine Needle Tip, Gold Product Specifications : Red: positive Black: negative Cable length: 88cm / 34.3" Total length: 106cm / 41.3" Professional test maximum voltage: 1000V 20A/10A Universal superfine pen for digital multimeter: 1000V 20A / 10A, test lead probe cable SMD SMT needle tip Product Features : Easy to read: "+" & "-" signs near probes (Red -''+''; Black - ''-'' ) Made of soft silicone, -50 ~ 200 still work fine, not easy to knot, not broken. Our Test Lead has one pair of red and black comfort grip probes with flexible insulated test leads With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT II 1000 V Ultra-sharp Probe Tips Gold-plated probe tips are sharp and hard, easy to reach small contact points on high-density boards Compatible with any meter equipped with shrouded banana input jacket Easy access to ICS, LED, SMD, etc. Package List : 1 Pair * Multimeter Probe Lead

Ve Pump Like Fuel Injection Pump for Isuzu,Jmc,etc. Ve Pump Parts Like Feed Pump ,Cam Plate, Drive Shaft, Solenoid Valve, Roller Ring, Cross Cube, Etc. Head Rotor : Isuzu, Toyota, Mitsubishi, Iveco, Fiat, etc Plunger : A, AD, P, PS7100, P8500, MW, PW, PT, Etc. Nozzle : DN_SD, DNOPDN, S, SN, P, PN, Etc. Repair Kit (VE pump,Lucas,etc.) Delivery Valve:(A,P type etc.) Pencil Nozzle : (Ford,CAT,etc), Common Rail Control Valve : (Bosch, Denso, Delphi) Lucas Head Rotor. (DPA, DPS, DP200), Diesel Fuel Injectors (Bosch, Denso, Delphi) Nozzle Tester, Test Bench and other test equipment..

Marine machinery steel casting parts like rudder horn, rudder carrier, a-bracket, stern tube, stern tube boss, anchor mouth, anchor chain wheel, stem post, , cement & mining spare parts like support roller, kiln tyre, half girth gear, bearing housing, mill head, hollow shaft, blocking wheel, rocker arm, frame and movable jaw plate of jaw crusher, cone crusher frame, petroleum & power generation machinery steel casting parts like head cover, full flow cross, blowout preventer shell, rotor shaft, lower ring, valve body, metallurgy, construction, transportation machinery casting parts like slag pot, pump casting, cylinder block, rolling mill housing.

Interface Probe Test Pin IFP-001 Used for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-001, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-001 interface probe is 14.22 mm in total length. If customers wish to change its length or diameter, we could do as required. This probe is unique in shape. It is straight whereas others, for example 002, 003, 004, 005, 006, 007, have an extra base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information was founded in 1980.  Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Interface Probe Test Pin IFP-007 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-007, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-007 interface probe is 40.05 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Interface Probe Test Pin IFP-004 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-004, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-004 interface probe is 17.8 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Interface Probe Straight Brass Pin IFP-002 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-002, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-002 interface probe is 14.3 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Interface Probe Straight Metal Pin IFP-003 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-003, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-003 interface probe is 16.33 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Interface Pin Test Probe IFP-005 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-005, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-005 interface probe is 17.8 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Perfume Bottle Components Fragrance Bottle Components Vodka antique metal label Metal label for perfume bottles, wine bottles. Making your bottle different, contact us for more MaterialZinc alloy Aluminum, other metal and plastic components is available Minimum order2,000pcs for zinc alloy label For other components, 10,000pcs per color&design ShapeRound, rectangle, square, oval, per your requirement SizeCan be customized Colorantique silver Other color is available, suce as gold, silver, black, antique gold etc StickersUsing high quality 3M glue on the back of metal label Surface finishedColor plating, enamel UV coating, vacuum metallizing, painting LogoEmbossed, debossed, laser engraving, silk printing, enamel DesignCustomized design� Leaders can help to design after knowing your ideas Drawing formatSTEP, IGES, CDR, AI, PDF Quality control100% quality inspection before packing PackingPP single polybag, copy papers, standard cartons TestsSalt spray test (nickel plated) Adhesion test Perfume friction test Lead time15 days for finishing mould and samples for metal label Mass production time depends on your order quantity LeadersadvantagesBest price as we are manufacturer Professional engineering and working teams in this industry Working for brands Free design & drawings Confidentiality agreements if needed Strict quality control Thorough testing equipments Save packing methods ,To make your bottle unique, we can make different components helping to achieve it, such as particular labels and special components made from ABS, aluminum, zinc alloy etc.If you need to make any labels and bottle components, please dont hesitate to contact us, we are always here for you! -

Perfume Bottle Components Metal Perfume Bottle Decoration Custom metal label for perfume bottles Metal label for perfume bottles, wine bottles. Making your bottle different, contact us for more MaterialZinc alloy Aluminum, other metal and plastic components is available Minimum order2,000pcs for zinc alloy label For other components, 10,000pcs per color&design ShapeRound, rectangle, square, oval, per your requirement SizeCan be customized Colorantique brassOther color is available, suce as gold , silver, black, antique gold etc StickersUsing high quality 3M glue on the back of metal label Surface finishedColor plating, enamel UV coating, vacuum metallizing, painting LogoEmbossed, debossed, laser engraving, silk printing, enamel DesignCustomized design Leaders can help to design after knowing your ideas Drawing formatSTEP, IGES, CDR, AI, PDF Quality control100% quality inspection before packing PackingPP single bag, copy papers, standard cartons TestsSalt spray test (nickel plated) Adhesion test Perfume friction test Lead time15 days for finishing mould and samples for metal label Mass production time depends on your order quantity Leaders advantagesBest price as we are manufacturer Professional engineering and working teams in this industry Working for brands Free design & drawings Confidentiality agreements if needed Strict quality control Thorough testing equipments Save packing methods Good after-sale service To make your bottle unique, we can make different components helping to achieve it, such as particular labels and special components made from ABS, aluminum, zinc alloy etc.If you need to make any labels and bottle components, please donhesitate to contact us, we are always here for you -

Rosemoun 3051S Coplanar Pressure Transmitter Introduction The Rosemount 3051S Coplanar Pressure Transmitter is designed with the patented Coplanar technology and is the no-equal solution for pressure, flow and level measurements. This scalable platform seamlessly integrates with manifolds, primary elements and seal solutions and optimizes performance for accurate differential, gage and absolute pressure measurements. With the SuperModule platform, this transmitter resists overpressure and line pressure effects to maintain unmatched performance. Specifications Warranty Up to 15-year limited warranty Rangedown Up to 200:1 Communication Protocol 4-20 mA HART,WirelessHART, FOUNDATION fieldbus Measurement Range Up to 2000psi (137,89 bar) Differential, Up to 2000psig (137,89 bar) Gage, Up to 4000psia (275,79 bar) Absolute Process Wetted Material 316L SST, Alloy C-276, Alloy 400, Tantalum, Gold-plated Alloy 400, Gold-plated 316L SST Diagnostics Basic Diagnostics, Power Advisory Diagnostics, Advanced Diagnostics Certifications/Approvals SIL 2/3 certified to IEC 61508 by an independent 3rd party, NSF, NACE, hazardous location, see full specs for complete list of certifications Features Patented Rosemount Coplanar technology offers optimized performance as a pressure, DP Flow and DP Level solution Best-in-class, scalable architecture enhances performance, functionality and process connections Transmitter arrives fully assembled and leak tested for simple installation and maintenance All-welded hermetic SST SuperModule platform resists overpressure and line pressure effects to ensure 0.025% accuracy Ultra and Ultra for Flow performance classes deliver 15-year stability and 15-year limited warranty 200:1 rangedown produce reliable measurements and wide application flexibility Integrates seamlessly with 4-20 mA HART WirelessHART, FOUNDATION� fieldbus protocols for application flexibility SIL 2/3 certified to IEC 61508 (via 3rd party) and prior-use certificate of FMEDA data for safety installations Advanced diagnostics provide diagnostic coverage to detect electrical loop issues and abnormal process conditions Remote display and interface offers easy access to process and device information

In the gem world, all kinds of gem-quality corundum other than ruby are called sapphire. The mineral name of sapphire is corundum, which belongs to the corundum group of minerals. In fact, the gem-quality corundum in nature is called sapphire, or colored sapphire, except for red called ruby, and other colors such as blue, light blue, green, yellow, gray, colorless, etc. Sapphire is preceded by a color name, such as pink sapphire. The chemical composition of sapphire (Al2O3) is mainly Fe, Ti, and color. Corundum contains iron (Fe) and titanium (Ti) and other trace elements, and presents blue, sky blue, light blue and other colors, among which the royal blue and cornflower colors that are considered to be thick but not black are the best. In cabochon cutting, when the interior is rich in three groups of inclusions parallel to the bottom surface and oriented, it can produce beautiful six-shot starlight, which is called star sapphire The composition of sapphire is alumina, which is blue due to the trace elements titanium (Ti4) or iron (Fe2). It belongs to the trigonal crystal system, and the crystal form is often cylindrical, short column, plate, etc., and the geometry is mostly granular or dense block. Transparent to translucent, vitreous luster. The refractive index is 1.76-1.77, the birefringence is 0.008, and the dichroism is strong. Heterogeneous body. Sometimes it has a special optical effect - the star effect. The hardness is 9, and the density is 3.95-4.1 g/cm3. No cleavage, fissure development. Industrial sapphire is a material used in special vehicles as transparent armor, and with the exception of diamonds, sapphire is harder than any other natural material. Sapphire belongs to the trigonal crystal system and has a hexagonal structure. The lattice constants are: a=b=4.758A, c=12.991A Refractive index 1.762-1.770 Birefringence: 0.008- 0.010 Uniaxial crystal negative light, in some cases abnormal biaxial crystal light Luster: bright glass luster to adamantine luster Pleochroism: Colored sapphires have dichroism, generally, dark blue/blue, blue/light blue, blue-green, blue-gray, yellow sapphire has golden/yellow, orange/light yellow, light yellow/ Colorless, wait.

Air filter element 1622185501 compressor filter ,the filter material of air filter is usually filter paper, there are two kinds of domestic south hangzhou paper and south Korean ossong paper, and the special one is American HV glass fiber. There are two kinds of end cover: metal end cover and PU end cover. The inner net, also known as the inner skeleton, USES a diamond or circular punch plate. The air filter has a single or medium pass, the filtration precision is 5-10 microns, the folding layer of the filter cannot be too sparse, and the number of folded layers is too small, which can affect the filtering precision. The normal service life of air filter is about 2200 hours. When the working environment is bad, the service life of the filter will be greatly shortened. We need to change the filter element in advance so as not to fail to reach the filtration precision and affect the service life of the equipment. Air filter element 1622185501 compressor filter-Function The action of the air filter is to filter out the dust particles in the inhaled air, and the filtered clean air is fed into the compression chamber of the screw rotor.The air filter is to filter the dust impurities in the air inhaled by the air compressor. The cleaner the air is, the more secure the oil filter core, oil and gas separation core and oil can be. Air filter element of screw air compressor: please replace the air filter in time when the following problems are encountered! 1. When the oil filter pressure difference alarm flashes. 2. Achieve the use cycle (working time). 3. High oil pressure of air compressor. 4. High temperature of machine and high exhaust temperature. Air filter element 1622185501 compressor filter -Air filter: 1619126900,1613872000,1613740700,1613740800,2901043100,1613950100,1613950300,1613800400,2901043100,,1619279800,290100500,,1030097900,2906009200,,1621054799,1627009499,1621054600,1030107000,1613900100,1622185501,1621510700,1621054700,1621574200,1621054699,1619279700,1619279900,3222188141,3222188131,3222332081,2914501700,2914501800,1625054700,1619569000 1619284700

Tungsten carbide productscutting tools: turning inserts, milling inserts, cut-off inserts, aluminium maching inserts, heavy cutting insert, woodworking inserts, brazed tips and brazed tools, paper cutting blade/knife, other customized inserts and tools etc., , wear parts: bushes & sleeves, nozzle & cover, sealing rings, saw blades, carbide rods/bar/plate for wearing purpose, other customized wear parts etc., , mining tools: coal auger bits, mining bits, button, mining tips, coal auger tips, excavating bits, other customized carbide tips and tools etc., , 2. Tungsten alloy:copper tungsten alloy(wcu alloy), silver tungsten alloy(wag alloy), tungsten heavy alloy(w-ni-fe, w-ni-cu), w-mo alloy etc. The shapes and sizes depend on customersâ?? requirements., , 3. Pure tungsten & molybdenum & tzm alloy :pure tungsten & molybdenum rods, plates/sheets etc. Molybdenum wire for heat spraying, tzm alloy, molybdenum copper alloy(mocu alloy) etc..

1. Mud Pump Parts Valve assembly/Valve body/Valve seat 1.The valve body and valve seat of valve assembly are made from high-quality knot steel treated with 20CrMnTi carburizing and quenching processes. 2.The surface hardness is greater than HRC 60. 3.The conical surface is ground finished to ensure a high requirement for roughness and geometric dimension. 4.The rubber sheet is made of polyurethane material which improves the service life of valve assembly, the operational use time is more than 300 hours. Different types: 1) Stem-guided Valves& Cross-arms Seats Stem-guided valve and cross-arms seat features an extra wide metal to metal seal on the valve flange. The serrated upper surface on the valve gives a longer non breathing seal between valve body and insert while the rigid seat cross-arms give greater strength and positibe sealing. 2) Three-wing valves and full open seats. Three-wing guided valves and full open seats features greater fluid flow than four wing valves, the unibody forged valve features greater strength than traditional welded wing valve. Innovative unibody valve design eliminates snap rings, plates or keepers providing reduced maintenance by snap-on valve inserts and easy installation. 3) Double angle O-ring valve The Double angle O-ring valve is made with a tough one-piece body to run more hours between change outs. Itâ??s made with carburized premium alloy steel to resist wear, provide a positive seal, and help protect against wash out or damage to the pump. Our products can fit in with most popular brands of Mud Pump

PT KIG is a the best supplier of premium coconut shell charcoal. We manufacture and export premium coconut charcoal products to various markets around the world. We are committed to being an innovative company and actively operating in the international briquette industry serving the needs of partners and building the indonesia company. With the motto the best & trusted charcoal. PT KIG very meticulous in its production, starting from the selection of quality coconut shell charcoal raw material, sophisticated production machinery and equipment to maintain all industry standart to produce premium quality coconut shell charcoal. Experienced, dedicated, and skill employees are the highest resource and enable PT KIG to perform the highest level to develop premium grade charcoal quality. In addition, our clients can ensure to ship their orders within the expected delivery time. We also serve orders from our partners for coconut shell charcoal with various shapes and spesifications, as well as partner brands in packaging on request. OFFICE & FACTORY INDONESIA Denpasar Bali (office) Gresik Jawa Timur (factory) Jogja Jawa tengah (factory) OUR PRODUCT : Grade A Diamond High quality Material 100 % coconut charcoal Briquettes Calori value 7000 -7200 kilo calori Total Moisture 7 % Ash conten 2 % White ash Fixed carbon 80 - 85 % Size 2.5 x 2.5 x 2.5 cm (can be customized) Size 3.5 x 2.5 x 2.5 cm (can be customized) Size 3 x 3 x 3 cm ( can be customized ) Size 2.5 x 2.5 x 5 cm ( can be customized) Package inner and master box included Price usd 1.370 /MT Grade B (Gold ) Material 100 coconut charcoal Calori value 7000 kilo kalori Total Moisture 7 - 10 % Ash content 3% White ash Fixed carbon 80 % Size 3.5 x 2.5 x 2.5 cm (can be customized) Size 3 x 3 x 3 cm ( can be customized ) Size 2.5 x 2.5 x 5 cm ( can be customized) Package master box 10 kg included Price usd 1.350 /MT Grade C (Silver ) Material 80 % coco 20 % coco granul charcoal Calori Value 6500 - 7000 kilo kalori Total moisture 7 - 10 % Ash content 4 - 5 % White ash Fixed carbon 75% Size 2.5 x 2.5 x 2.5 cm (can be customized ) Price usd 1.270 / MT Minimum order 1 container