Single-head Automatic Seal Ring Making MachineApplication: The equipment is applied to make the seal rings of 18L / 20L chemical cans,and paint buckets.This machine is used to fill the sealing strips of the chemical cans or paint buckets automatically, which breaks original manual operation. It really realizes unmanned operation.We adopt the EVA foaming technology, using EVA foaming strips instead of the traditional rubber strips. The cost of the traditional rubber strips is high, which needs 0.5-0.8 RMB per cap. However, EVA foaming strips are much cheaper, only need 0.06-0.07 RMB per cap. The EVA foaming strips are not only cheap, they also have better sealing effect. At the same time, they have the advantages of acid and alkali resistance and corrosion resistance. Parameters:Single-head  Automatic Seal Ring Making MachineWeight0.4TVoltageThree-phrase  380VSize mmlength*width*height1050*1050*1400Pressure4-6MPaProduction  Capacity16 sets/ minTotal Power1.5kw System ParametersCushion Angle50 degreesCushion Revolution0.3 revolution/sPulses/circle1000Reduction Ratio9 Advantages:The equipment can reduce workersâ?? workloads, and help workers improve work efficiency.The equipment is easily operated, and can control the length of the rubber strip accurately. Services:Ã? Provide the technical design and solutions;Ã? Designing and manufacturing of non-standard equipment;Ã? Professional technical training and guidance on site according to the contract;Ã? Tele-technical consulting and services;Ã? Other special technical service according to clientâ??s requirements. Faults & Methods for Single-head automatic seal ring making machine:Fault 1: The unreeling machine keeps spinning for a long time.Cause: It induces unreeling signal unsuccessfully.Method: On the premise of having material, please adjust the proximity switch to the center of the gravity wheel, till the light is on.Fault 2: The feeding cylinder doesnâ??t go forward.Cause: Its start- point or all parts of it induce the signal unsuccessfully.Methods: Please check the small cylinderâ??s induction which can screw down & lift up in the pushing part;Please check the induction of pushing cylinder;Please check if the photo-electricity switches of all work-pieces are on;Please check if the gas path is unobstructed.
Single-head Automatic Seal Ring Making MachineApplication: The equipment is applied to make the seal rings of 18L / 20L chemical cans,Website:, and paint buckets.This machine is used to fill the sealing strips of the chemical cans or paint buckets automatically, which breaks original manual operation. It really realizes unmanned operation.We adopt the EVA foaming technology, using EVA foaming strips instead of the traditional rubber strips. The cost of the traditional rubber strips is high, which needs 0.5-0.8 RMB per cap. However, EVA foaming strips are much cheaper, only need 0.06-0.07 RMB per cap. The EVA foaming strips are not only cheap, they also have better sealing effect. At the same time, they have the advantages of acid and alkali resistance and corrosion resistance. Parameters:Single-head  Automatic Seal Ring Making MachineWeight0.4TVoltageThree-phrase  380VSize mmlength*width*height1050*1050*1400Pressure4-6MPaProduction  Capacity16 sets/ minTotal Power1.5kw System ParametersCushion Angle50 degreesCushion Revolution0.3 revolution/sPulses/circle1000Reduction Ratio9 Advantages:The equipment can reduce workersâ?? workloads, and help workers improve work efficiency.The equipment is easily operated, and can control the length of the rubber strip accurately. Services:Ã? Provide the technical design and solutions;Ã? Designing and manufacturing of non-standard equipment;Ã? Professional technical training and guidance on site according to the contract;Ã? Tele-technical consulting and services;Ã? Other special technical service according to clientâ??s requirements. Faults & Methods for Single-head automatic seal ring making machine:Fault 1: The unreeling machine keeps spinning for a long time.Cause: It induces unreeling signal unsuccessfully.Method: On the premise of having material, please adjust the proximity switch to the center of the gravity wheel, till the light is on.Fault 2: The feeding cylinder doesnâ??t go forward.Cause: Its start- point or all parts of it induce the signal unsuccessfully.Methods: Please check the small cylinderâ??s induction which can screw down & lift up in the pushing part;Please check the induction of pushing cylinder;Please check if the photo-electricity switches of all work-pieces are on;Please check if the gas path is unobstructed.
Single-head Automatic Seal Ring Making MachineApplication: The equipment is applied to make the seal rings of 18L / 20L chemical cans,Website:http://www.xinchengcanmaking.com, and paint buckets.This machine is used to fill the sealing strips of the chemical cans or paint buckets automatically, which breaks original manual operation. It really realizes unmanned operation.We adopt the EVA foaming technology, using EVA foaming strips instead of the traditional rubber strips. The cost of the traditional rubber strips is high, which needs 0.5-0.8 RMB per cap. However, EVA foaming strips are much cheaper, only need 0.06-0.07 RMB per cap. The EVA foaming strips are not only cheap, they also have better sealing effect. At the same time, they have the advantages of acid and alkali resistance and corrosion resistance. Parameters:Single-head  Automatic Seal Ring Making MachineWeight0.4TVoltageThree-phrase  380VSize mmlength*width*height1050*1050*1400Pressure4-6MPaProduction  Capacity16 sets/ minTotal Power1.5kw System ParametersCushion Angle50 degreesCushion Revolution0.3 revolution/sPulses/circle1000Reduction Ratio9 Advantages:The equipment can reduce workersâ?? workloads, and help workers improve work efficiency.The equipment is easily operated, and can control the length of the rubber strip accurately. Services:Ã? Provide the technical design and solutions;Ã? Designing and manufacturing of non-standard equipment;Ã? Professional technical training and guidance on site according to the contract;Ã? Tele-technical consulting and services;Ã? Other special technical service according to clientâ??s requirements. Faults & Methods for Single-head automatic seal ring making machine:Fault 1: The unreeling machine keeps spinning for a long time.Cause: It induces unreeling signal unsuccessfully.Method: On the premise of having material, please adjust the proximity switch to the center of the gravity wheel, till the light is on.Fault 2: The feeding cylinder doesnâ??t go forward.Cause: Its start- point or all parts of it induce the signal unsuccessfully.Methods: Please check the small cylinderâ??s induction which can screw down & lift up in the pushing part;Please check the induction of pushing cylinder;Please check if the photo-electricity switches of all work-pieces are on;Please check if the gas path is unobstructed.
Single-head Automatic Seal Ring Making MachineApplication: The equipment is applied to make the seal rings of 18L / 20L chemical cans,Website:http://www.xinchengcanmaking.com, and paint buckets.This machine is used to fill the sealing strips of the chemical cans or paint buckets automatically, which breaks original manual operation. It really realizes unmanned operation.We adopt the EVA foaming technology, using EVA foaming strips instead of the traditional rubber strips. The cost of the traditional rubber strips is high, which needs 0.5-0.8 RMB per cap. However, EVA foaming strips are much cheaper, only need 0.06-0.07 RMB per cap. The EVA foaming strips are not only cheap, they also have better sealing effect. At the same time, they have the advantages of acid and alkali resistance and corrosion resistance. Parameters:Single-head  Automatic Seal Ring Making MachineWeight0.4TVoltageThree-phrase  380VSize mmlength*width*height1050*1050*1400Pressure4-6MPaProduction  Capacity16 sets/ minTotal Power1.5kw System ParametersCushion Angle50 degreesCushion Revolution0.3 revolution/sPulses/circle1000Reduction Ratio9 Advantages:The equipment can reduce workersâ?? workloads, and help workers improve work efficiency.The equipment is easily operated, and can control the length of the rubber strip accurately. Services:Ã? Provide the technical design and solutions;Ã? Designing and manufacturing of non-standard equipment;Ã? Professional technical training and guidance on site according to the contract;Ã? Tele-technical consulting and services;Ã? Other special technical service according to clientâ??s requirements. Faults & Methods for Single-head automatic seal ring making machine:Fault 1: The unreeling machine keeps spinning for a long time.Cause: It induces unreeling signal unsuccessfully.Method: On the premise of having material, please adjust the proximity switch to the center of the gravity wheel, till the light is on.Fault 2: The feeding cylinder doesnâ??t go forward.Cause: Its start- point or all parts of it induce the signal unsuccessfully.Methods: Please check the small cylinderâ??s induction which can screw down & lift up in the pushing part;Please check the induction of pushing cylinder;Please check if the photo-electricity switches of all work-pieces are on;Please check if the gas path is unobstructed.
Circular Blade Circular blade, also known as circular blade. The shape is circular. Generally speaking, circular blades are used on mechanical equipment for processing functions such as cutting and trimming. Circular blades usually have an intermediate hole, so they can be fixed on mechanical equipment to achieve cutting function. There are also many types of toothed circular blades (flat, pointed, and irregular) with three types of cutting edges: double-sided, single-sided, and non cutting.Alloy cutting head Alloy cutting head is a tool suitable for rough turning, rough planing, rough milling, drilling and expanding of general and deep holes in cast iron, non-ferrous metals and their alloys, non-metallic materials with uneven surfaces and intermittent cutting.Knife head shaft Transmission of torque, support of blades, determination of blade position and rotation centerPressure rod For coiled tubingSand belt Sand belts belong to coated abrasives and are called flexible abrasives. Compared to solid grinding wheels, polishing is more flexible and safe, with higher accuracy and lower grinding costs.
Application : Used in Street Light Isolator, Distribution Board, Switchgear, Electrical Panels Boards, Electrical and Telecommunication, Circuit breaker, RCD, etc. In MCBs ELCBs and Isolators to protect the installation For termination of neutral and ground wires on bus bar For termination of Rated Conductors For mounting of DIN Rails and clamp type For surface mount applications Designed for Easy Installation and Termination Carries current back to the source Material : Free Cutting Brass, High Tensile Brass, CDA 360 Brass, Alloy 360 Brass, CDA 230 Brass. Size : Begins from M2 or equivalent threads, 2 ways to 50 ways. Length : 1 meter to 15 meter or as per customers requirement. Suitability : 70Amp, 90A, 110A, 165A through 350Amp Screws : Steel Multi-Head, Zinc plated - Headless set screw, Headed slotted machine screw, Headed machine screw combination & square slot, Headless Hex socket, etc. Finish : Natural, Nickel Plated, Tin Plated, Chrome Plated, Electrolyte Tin Plated or any coating as per customer specification. Features : Lighter and easier to handle. The use of modern polymer channel has reduced the weight of the products making them easier to handle. Pre-Drilled fixing holes for ease of installation. Plastic channel base is entirely corrosion proof. High Durability, Tensile strength and Resistant to adverse conditions.
FELIS Single Needle Frame Type Mattress Quilting Machine FELIS is a frame by frame single needle computerized quilting machine. It has a moving sewing head and moving frame in order to accelerate the movements by reducing the weight of moving parts. With the advantage of the moving sewing head, FELIS also brings 50% space requirement advantage compared to conventional frame by frame quilting machines. It needs half the space of a conventional fixed head quilter. With the ability of quilting very different products, FELIS offers perfect quilting quality for all the products from very thin garment products to thick materials for mattress industry with multiple layers including foam, visco, memory foam, latex, polyester fiber, non woven, jacquard fabric, knitted fabric, leather and down fill. Minimum bobbin change with XXL spools (Durkopp Adler) Automatic thread cutting in less than 0,5 second High operator security systems Automatic frame measure control system Remote & Smartphone production monitoring system Easy pattern adaptation Flexible and user friendly software : EtQuilt
The leon-pt mattress border side stitching machine is designed to make luxurious hand-stitched borders. Unlike the machines in the market, leon-pt offers not only hand-stitched border but also circle, rectangle, plus shape, s shape, and various different figures to be stitched. The leon-pt4 can make one mattress border less than 3 minutes according to number of tacks and mattress size. It offers unlimited positioning of tacks as 2-3-4-5-6 tack on each row. It offers ability to create different tack designs using the touch screen panel. No quilt repair machine: ability to continue sewing from the stop or desired point Servo motor driven motion control system Reliable jukä° lk 1900 tacking heads Automatic bobbin finish detector Smooth movement of the border for accurate and straight tacks.
MaAnt S2/S2PM dot matrix coordinator for X-14 Pro Max Face ID dot projector positioning repair. MaAnt S2 dot matrix lattice coordinate storage instrument for iPhone X-12 Pro Max. MaAnt S2PM dot matrix lattice coordinate storage fixture for 13/13 mini/13 Pro/13 Pro Max/14/14 Plus/14 Pro/14Pro Max. Option: MaAnt S2: For X/XS/XS Max/XR/11/11Pro/11 Pro Max/12/12Mini/12 Pro/12 Pro Max. MaAnt S2PM: For 13 Mini/13/13 Pro/13Pro Max/14/14 Plus/14 Pro/14Pro Max. Features: Fast fix. Multi-model adaptation. Easily push the sliding block. High hardness aluminum alloy. Auxiliary fit and precise alignment. Quick alignment to get rid of alignment by feeling. The dot matrix module can be removed for repair. All-aluminum body, thin and durable, solving the problem of difficult dot matrix alignment and inability to record during face-to-face repair. Usage: The dot matrix module saves the original coordinates to the coordinate instrument before repairing, using L and R screws to fix it, or marking the scale strip on the limiting tablet. Remove the point array module at will to repair or replace the IC or replace the flex cable of the IC. After the replacement, the point array module is restored to the original coordinate position stored last time with the help of this product's limiting plate. Blind operation, easy to push the sliding block so that repair dot matrix no longer bothers for alignment.
LDT-L200 Ladle Lining Laser Thickness Gauge Overview LDT-L200 is a new generation of ladle lining thickness gauge launched by our company. The system equipment emits a pulsed laser beam to the lining surface of the ladle, and receives the returned laser light to measure its flight time. Then the system equipment calculates the distance between the equipment and the target point according to the transmission speed of the laser. During measurement, the user pushes the equipment to a certain position on the platform in front of the ladle, and the equipment can start to scan and measure the target area of the ladle after the equipment performs rapid self-positioning. The detection principle The measurement speed of LDT-L200 can reach up to 2,000,000 points per second, and each scan can obtain distance data of more than 1.5 million points. The actual surface curve of the entire ladle lining can be obtained by combining the measurement data of different positions. During the measurement, the laser head of the equipment rotates at a certain step angle to rapidly change the angle of the pulsed laser beam. Within 1 minute, the three-dimensional surface contour of the ladle lining can be formed, and the thickness information of the furnace lining can be obtained through coordinate conversion calculation. The measurement accuracy up to 2mm. In order to accurately calculate the thickness of the lining in the ladle, the measuring head of the laser thickness gauge is installed on the ladle repairing platform. By moving the swivel arm for hoisting, the laser scanning head is moved to the intersection position during measurement, and the relative position of the laser head to the ladle mouth will be calculated during installation. Through mathematical modeling, a complete 3D figure of the thickness of the entire ladle lining can be displayed after laser scanning The main components 1. Laser measuring head 2. Fixed laser thickness gauge host 3. Optical fiber communication 4. Cooling circulation system The technical indexes Laser reproducibility: 2mm Laser accuracy: 2mm Local fastest measurement time:
Model number: x-280a 10r 280w 3in1 wash light led spot moving head with dmx concert light We produce dmx led moving head spot light. We devoted ourselves to stage special effect equipment for many years, covering most of europe and the america market. We are expecting become your long-term partner in china. Specification of the 10r 280w 3in1 wash light led spot moving head with dmx concert light: Power consumption: 470w Power supply: ac 100-240v 50/60hz Light source: 280w 10r lamp Average lifespan: 2200hrs Color wheel: 13 dichroic filters + white Gobo wheel: 9 bidirectional and indexable gobos (outside diameter: 15, 4 mm, image diameter: 13 mm) static gobo wheel with 14 fixed gobos, at variable rotation Prism 1: 8-facet circular prism rotating in both directions at different speeds Prism 2: 6-facet linear prism rotating in both directions at different speeds Zoom: parallel beam angel 2.5â°-20 change Wash effect: adjustable wash effects angle Product features of the 10r 280w 3in1 wash light led spot moving head with dmx concert light: 1. This newest style 280 3in1 disco lights chinese has novel design and compact structure can be as a very professional moving head light 2. It has small beam angle, bean angle scale freely, has multistage beam angle change effect. 3. It has high brightness, downy lighting, and professional linear focus. 4. This new technology fixture even travels efficiently in a case of 4 and will cover all your needs beam, spot, wash
HCM MEDICA is a professional manufacturer for all kinds of medical headlight, product is widely use in ENT, gynecology, neurosurgery, cardiosurgery and many other applications. 1. Led power: 8w. 2. The head loop is adjustable, compact,light in weight.3. It uses high quality material so as to achieve an excellentillurmination effect. 4. Color temperature is 5000K - 6,500K,CRI 70. 5. Intensity: HCM6694- 22000Lx, HCM6694 PLUS - 36000Lx. 6. wide range power for charger from 100 - 240 VAC, 50/60Hz. 7. Provide high capacity battery, which makes the headlight work at the highest intensity for minimun 4 hours, charging time 4 hours. HCM6694 8W surgical headlight is completely different from traditional medical headlight, very soft and compact, light in weight; you almost could not feel its existence. It could be used for general surgery, ENT, dental, gynecology, plastic surgery, orthopedics, and other general applications. It could also be used for deep surgery (HCM6694 PLUS only), such as neurosurgery, cardiosurgery, blood vessel surgery, spine surgery, etc. The head loop is adjustable, extremely soft, compact, light in weight. Imported led bulb from USA, lens system from Germany, which brings you an excellent illumination effect. High capacity battery, which makes theheadlight work at the highest intensity for minimum 3.5 hours, charging time 4 hours.
HCM MEDICA is a professional manufacturer for all kinds of medical headlight, product is widely use in ENT, gynecology, neurosurgery, cardiosurgery and many other applications. 1. Led power: 8w. 2. The head loop is adjustable, compact,light in weight.3. It uses high quality material so as to achieve an excellentillurmination effect. 4. Color temperature is 5000K - 6,500K,CRI 70. 5. Intensity: HCM6694- 22000Lx, HCM6694 PLUS - 36000Lx. 6. wide range power for charger from 100 - 240 VAC, 50/60Hz. 7. Provide high capacity battery, which makes the headlight work at the highest intensity for minimun 4 hours, charging time 4 hours. HCM6694 8W surgical headlight is completely different from traditional medical headlight, very soft and compact, light in weight; you almost could not feel its existence. It could be used for general surgery, ENT, dental, gynecology, plastic surgery, orthopedics, and other general applications. It could also be used for deep surgery (HCM6694 PLUS only), such as neurosurgery, cardiosurgery, blood vessel surgery, spine surgery, etc. The head loop is adjustable, extremely soft, compact, light in weight. Imported led bulb from USA, lens system from Germany, which brings you an excellent illumination effect. High capacity battery, which makes theheadlight work at the highest intensity for minimum 3.5 hours, charging time 4 hours.
Dt ii fixed belt conveyor is a general-purpose products using cotton canvas, nylon, polyester canvas and steel cord conveyor belt components for drag cited continuous conveyor equipment, can be widely used in electric power, coal, mining, iron and steel, building materials, chemicals, environmental protection, food, light industry, oil and many other industries. Transport various bulk, block or integer goods with loose density 500-2500kg/m 3. With the features of great traffic and climbing ability, and small noise, easy maintenance, good interchangeability of wearing parts etc., this kind of conveyor is good for the transport system automation control. And the working environment temperature is lower than 40degrees celsius. Dt ii fixed belt conveyor is composed of conveyor belt, driving device, cylinder, roller, tension device, rack, head funnel, feed channel, sweeper, unloader, electrical safety protection device. It is a continuous conveyor equipment using cotton canvas, nylon, polyester canvas and steel cord conveyor belt components for drag cited. Transport various bulk, block or integer goods with loose density 500-2500kg/m 3.
Bluetech Tapping Machines are produced to put an end to the tapping problems and they are extremely ergonomic and powerful.BHK series machines can be guide in each diameter between M5 and M36 , Thanks to their dual-stage can be set to the desired torque and speed gearbox & thanks for fullfills tasks so that the most accurate and easily. Moveable arm mechanism on the machine can scan a large area. The mechanism can be approached in the most sensitive way to other points located around the machine also the parts attached on the T-channel table.Angle head can be changed according to the position of the workpiece horizontally, vertically or in angled , will also fixed in each desired angle. Bluetech BHK series machines are not using only tapping, they can also use for reaming, chamfering and die extrusion process. You can do whole process with in the shortest time and can fullfill the most accurate way. z
1.The brief introductions of the walking pile driver A widen and larger chassis is installed on the pile driver. Using hydraulic movement, in the fixed position of the main frame can be rotated arbitrarily, fast, good stability. Piling depth can reach 16 meters, power drill power can reach 30 kw. This car is equipped with hydraulic automatic unearthed tube do not need manual shovel. Suitable for piling high-rise buildings, highways, power facilities, solar photovoltaic power generation, this car has the characteristics of fast positioning, quick piling, high efficiency and good movement stability. 2.The technical parameters of the walking pile driver Item Unit Parameters Borehole diameter mm 150-800 Drilling depth m 13-15 Power head speed rpm 40 Power head power kw 30 Climbing ability ° 40 Drill pipe diameter mm 300-1200 Max torque kn.m 8800 Rotation angle ° 360 Move speed km/h 2-3 Dimension cm 1470*230*280 Vehicle weight t 9 (In the continuous improvement of products, technical parameters are based on practical consultation.)
Description: BLMT shear bolted lugl is connection type power fitting between the wire and equipment, mainly used for non-bearing connection in insulated wire, aluminum wire, ACSR and copper wire. The terminal body is made of a high strength tinned aluminum alloy, and the inner surface of the conductor hole has a mesh concave design. Double shear head bolts are made of special aluminum alloy and are treated with high quality lubricants and are equipped with a special contact ring which can not be removed once the bolt head is cut off. Insert or remove the special insert to adjust the scope of the applicable conductor. These inserts have longitudinal stripes and a positioning slot. This product model is streamlined, suitable for different diameter connection. For example: three models can cover from 25mm2 to 240mm2 conductor. The terminals are suitable for outdoor and indoor applications and can provide different bolt size specifications. Characteristics: Wide range of applications; Compact design; Can be used with almost all types of conductors and materials; Fixed torque and double shear head bolt ensure good electrical contact performance; Can be easily installed by using standard socket wrenches; Using a leading industrial design, enable the perfect installation on mdedim voltage cable of up to 42kV. Installation description: No need specialized tools to install; Only need a socket wrench to complete the installation; Including the provision of inserts; Double shear head bolt design with gradable torque to ensure reliable and firm contact; We recommend the use of a support tool to prevent the conductor from bending; Each connector or cable lug has a separate mounting command. Model No.: BLMT-25/95-13 Cross section range: 25-95 Bolt: M13
Description: blmt shear bolted lugl is connection type power fitting between the wire and equipment, mainly used for non-bearing connection in insulated wire, aluminum wire, acsr and copper wire. The terminal body is made of a high strength tinned aluminum alloy, and the inner surface of the conductor hole has a mesh concave design. Double shear head bolts are made of special aluminum alloy and are treated with high quality lubricants and are equipped with a special contact ring which can not be removed once the bolt head is cut off. Insert or remove the special insert to adjust the scope of the applicable conductor. These inserts have longitudinal stripes and a positioning slot. This product model is streamlined, suitable for different diameter connection. For example: three models can cover from 25mm2 to 240mm2 conductor. The terminals are suitable for outdoor and indoor applications and can provide different bolt size specifications. Characteristics: wide range of applications; Compact design; Can be used with almost all types of conductors and materials; Fixed torque and double shear head bolt ensure good electrical contact performance; Can be easily installed by using standard socket wrenches; Using a leading industrial design, enable the perfect installation on mdedim voltage cable of up to 42kv. Installation description: no need specialized tools to install; Only need a socket wrench to complete the installation; Including the provision of inserts; Double shear head bolt design with gradable torque to ensure reliable and firm contact; We recommend the use of a support tool to prevent the conductor from bending; Each connector or cable lug has a separate mounting command.
Description: BLMT shear bolted lugl is connection type power fitting between the wire and equipment, mainly used for non-bearing connection in insulated wire, aluminum wire, ACSR and copper wire. The terminal body is made of a high strength tinned aluminum alloy, and the inner surface of the conductor hole has a mesh concave design. Double shear head bolts are made of special aluminum alloy and are treated with high quality lubricants and are equipped with a special contact ring which can not be removed once the bolt head is cut off. Insert or remove the special insert to adjust the scope of the applicable conductor. These inserts have longitudinal stripes and a positioning slot. This product model is streamlined, suitable for different diameter connection. For example: three models can cover from 25mm2 to 240mm2 conductor. The terminals are suitable for outdoor and indoor applications and can provide different bolt size specifications. Characteristics: Wide range of applications; Compact design; Can be used with almost all types of conductors and materials; Fixed torque and double shear head bolt ensure good electrical contact performance; Can be easily installed by using standard socket wrenches; Using a leading industrial design, enable the perfect installation on mdedim voltage cable of up to 42kV. Installation description: No need specialized tools to install; Only need a socket wrench to complete the installation; Including the provision of inserts; Double shear head bolt design with gradable torque to ensure reliable and firm contact; We recommend the use of a support tool to prevent the conductor from bending; Each connector or cable lug has a separate mounting command. BLMT-185/400-17 Cross section range: 185-400 Diameter of mounting hole: 17 Bolt: M22
Braun Card D421.51U1 Steam turbine parts YOYIK knows that innovation is the core driving force of corporate development, so it continues to increase R&D investment and establish an advanced R&D center, focusing on improving product performance and efficiency, reducing energy consumption, and reducing environmental impact. The company has also carried out in-depth cooperation with many scientific research institutions and universities at home and abroad to jointly explore cutting-edge technologies in the power equipment industry and promote technological innovation in the industry. Yoyik can offer many spare parts for power plants as below: #DF-Braun Card D421.51U1 Steam turbine parts-DF Eddy Current Sensor PR6422/000-140 proximity probe sensor CON021/916-100 speed sensor CS-1 G-065-04-01 circuit board ME8.530.004 LVDT Sensor 6000AT LVDT Sensor Z96200WN pick up coil sensor ZS-04 non contact linear position sensor 5000TD-E Protective Relay CSC 237A LVDT Sensor TD-1G-400-15 Wrnk2-131 Pressure Switch 5NN-K45-N4-F1A Pressure reducing valve PQ-235C eddy current sensor are used to TM0180-A05-B05-C03-D10 Wrnk2-131 LVDT sensor ZD-5000TD Bolt heater DC control cabinet ZDK-IV 60KW Analog RTD LP Case exhaust WTYY-1031 Eddy Current Signal Converter CON011/912-015 Analog Output Module HAO805 Vibration sensor HD-ST-2 Differential pressure switch BDSN4KB25XFSHX sensor TM0180-05-05-03-10-02 pressure transducer sensor YWK-50-C Torque Control Module SY-JB (Ver 2.10) Bolt electric heating rod ZJ-17-T4(R) non contact linear sensor DET700A speed sensor CS-4-100-02-02 cable ZC-KVVP-0.45/0.75 8mm Eddy Current Sensor TM301-A02-B00-C00-D00-E00-F00-G01 LVDT Sensor 191.36.09.13 Magnetoresistive speed probe HRY1-A100-B02-C02-D05-E080 Flow Switch LKB-01B Eddy Current Sensor PR6423/001-110 Pt100 -RTD temperature probe 20cm Probe length, Fixing Thread: 1/8" G or NPT INSULATING PULLING ROD ZN63-VS1-12KV Braun Card D421.51U1 Steam turbine parts MY-DFYL-2024-7-18
