TEMPO make soxhlet extraction heaters are designed to use in laboratories for solvent extraction under reflux. Typical applications are the determination of residual oil content in oil cake, assay of crude herbal drug sources etc. Max surface temp 400C Supply 230V, AC Construction : TEMPO make soxhlet extraction heaters is suitable to heat soxhlet flasks of 100-350 ml capacity. The heating element is attached to knitted fabric to provide flexible support to the bottom of the flask. Glass wool insulation fills the gap between the metal casing and the heater. In event of spillage, the solvent will either evaporate or escape through the draining hole below each element. The housing has two retort rods and a cross bar on which the extraction apparatus is fixed. The apparatus has an inbuild energy regulator which controls all the heaters. The heating elements have individual ON/OFF switch and pilot lamp to indicate working. Controlling System : Energy regulator and pilot lamp Heating System : The heating element is attached to knitted fabric to provide flexible support to the bottom of the flask. Glass wool insulation fills the gap between the metal casing & the heater.
TEMPO make laboratory autoclave are suitable for pharma & biotech industries, food research & quality assurance labs, agriculture research, healthcare & diagnostic labs, university, etc. Temperature range 121 C to 125 C Pressure range 15 to 22 PSI Factory set 15 PSI at 121 C Supply 230V, AC Construction : Vertical double walled design has a single chamber for steam & water. Lid, flange & bottom plate is also made of SS, all joints are argon welded. Jointless silicon gasket. Heavy duty industrial flange heater. Lid fitting pressure gauge 0-30 PSI, safety spring loaded pressure valve, steam release valve. Safety high pressure release valve. Foot lifting arrangement is provided in 121C/D/E/F, a basket made of thick stainless steel (S.S.) rod wire mesh. Technical Specification : Semi automatic system for autoclave is supplied with microprocessor based digital temperature controller with an inbuilt timer. Low water level cuts off the system with magnetic oat switch for heaterâ??s safety. Fully automatic system for autoclave is supplied with microprocessor based digital temperature controller with an inbuilt timer. Low water level cuts off the system with magnetic oat switch for heater's safety.
TEMPO make TI 128HT series ovens are made of triple-walled construction. The motorized blower with V-belt fitted on the top side of the chamber for re-circulation of air to maintain the uniformity of temperature inside the chamber. The unit is insulated with 4 high grade glass wool. Single door fitted on heavy hinges. The unit is provided with user friendly adjustable stainless steel rod mesh trays. Temperature range 50 C to 450 C Temperature accuracy ±1 C Temperature uniformity ±1% of the set temperature Supply 230V, AC Controlling System : Two separate imported microprocessors based auto tune PID controller with CE mark & dual display of set value & process value for precise control of temperature. Air Circulation : The motorized blower with a V belt drive on the top side of the chamber develops the unique airflow distribution inside the chamber. The unique airflow system ensures quick recovery after the doors are opened. Heating System : High-quality U shape SS tubular heating elements used on the side walls to maintain uniform condition inside the chamber.
CORRECT TEST POSTURE Body Posture The correct posture is standard stand posture, with arm sand feet departed, to get an accurate test result,please remove your heavy clothes and other objects away When testing, please keep your arms hanging naturally with an 15 angle to the body, and contacts between body and legs should be avoided. Keep relaxed,never be tension,move or speak loudly Correct Posture To Grip Electrodes To grip electrode rods with two hands,keep your fingers griping on the inside of the electrode respectively and equably. press the outside pole of the electrode rod.Do not press electrode parcel with your finger mails. And do not loosen it throughout the testing process. lf there is a protective layer on the electrode. piease remove it. Correct Posture To Stand On Electrode A.Stand with bare foot on the electrode parcel. B.Keep the heel stomping on the circular electrode parcel, the soles standing on the oval electrode parcel. C.if the feet are too small,please let the feet stand between electrodes parcels located front and rear,toensure that feet can fully come into contact with the electrode parcels at two ends. D.lf there are thick cocoons on the soles or unclean objection feet, it may affect the normal test, please wipe it with wet towel.
NCM-5.1 Rail Switch Grinding Machine NCM-5.1 frog and switch grinder is specifically designed for grinding operations through switch and crossings and either side of the rail head. The grinding device of the machine can be tilted by 30° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency. It has the characteristics of precise turning and positioning at any position and angle of the turmout rail head. Specification Model NCM-5.1 Type Rail Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 2100*1120*1030mm Engine Honda GX270 Petrol engine Rated power 5.1kW Grinding wheel speed 3600r/min Grinding wheel feeding stroke 80mm Feed adjustment accuracy l0mm Grinding wheel rotation angle 30° Weight 117kg
Portable Rolling Track Gauge Portable Rolling Track Gauge is mainly used for railway track gauge and super-elevation(cant), check rail gauge and back to back distance measurement. It can be used for track inspection and fine adjustment of rail gauge.This product has the advantages of fast measuring speed, stable pushing rod, easy to carry, and night-time and tunnel work,legible even in direct sunlight are supported. It is an ideal measuring tool for track fine-tuning, track construction,inspection and track laying. Features The benefits of our rolling gauge : 1. Measure the track gauge, cant without bend over your back. 2. Light weight : around 6.5kg , one person operation. 3. BT connection, data uploading and analysis system. 4. High working efficiency. Save your man power. ( 1 man with 1 rolling gauge = 4 man with 4 normal digital track gauge) Specification Model (1435mm) GJC-JJG0 Track gauge 1410-1470mm -185~+185mm Display mode OLED display and hand-held terminal display Supply Voltage DC3.4V-5.2V (rechargeable battery) 0.05mm Working temperature -30-+55 Insulation performance 1M© 0.01mm 0.05mm ±0.25mm Superelevation max indication error ±0.3mm Length 1700mm Net Weight 6.5kg
Product Description NGM-5.1 Rail Profile Grinding Machine This machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency. BENIFITS Angle of the grinding head is set using an adjustment wheel, lowering/raising of the grinding stone is electrically contlled Equipped with spark protection device Equipped with electric control system prevents over grinding by limiting the lowering of the grinding stone Grinds the whole head of rail in one single operator, no need to turn the machine or to handle it Specification Model NGM-5.1 Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 1500 * 450 * 750 mm Engine HONDA GX270 Power 5.1 kW Grinding wheel specifications 125x65 mm Feeding accuracy 0.1 mm Turning angle of grinding stone ±90° Spindle revolution 4100r/min Grinding stone feeding stroke 42 mm Profile wheel span 1000 mm Weight 100 kg Weight of supporting rod 14 kg
Product Description NGM-5.1 Rail Profile Grinding Machine This machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency. BENIFITS Angle of the grinding head is set using an adjustment wheel, lowering/raising of the grinding stone is electrically contlled Equipped with spark protection device Equipped with electric control system prevents over grinding by limiting the lowering of the grinding stone Grinds the whole head of rail in one single operator, no need to turn the machine or to handle it Specification Model NGM-5.1 Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 1500 * 450 * 750 mm Engine HONDA GX270 Power 5.1 kW Grinding wheel specifications 125x65 mm Feeding accuracy 0.1 mm Turning angle of grinding stone ±90° Spindle revolution 4100r/min Grinding stone feeding stroke 42 mm Profile wheel span 1000 mm Weight 100 kg Weight of supporting rod 14 kg
Product Description NCM-5.1 Rail Switch Grinding Machine NCM-5.1 frog and switch grinder is specifically designed for grinding operations through switch and crossings and either side of the rail head. The grinding device of the machine can be tilted by 30° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency. It has the characteristics of precise turning and positioning at any position and angle of the turmout rail head. Specification Model NCM-5.1 Type Rail Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 2100*1120*1030mm Engine Honda GX270 Petrol engine Rated power 5.1kW Grinding wheel speed 3600r/min Grinding wheel feeding stroke 80mm Feed adjustment accuracy l0mm Grinding wheel rotation angle 30° Weight 117kg
NGM-5.1 Rail Profile Grinding Machine This machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency. BENIFITS Angle of the grinding head is set using an adjustment wheel, lowering/raising of the grinding stone is electrically contlled Equipped with spark protection device Equipped with electric control system prevents over grinding by limiting the lowering of the grinding stone Grinds the whole head of rail in one single operator, no need to turn the machine or to handle it Specification Model NGM-5.1 Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 1500 * 450 * 750 mm Engine HONDA GX270 Power 5.1 kW Grinding wheel specifications 125x65 mm Feeding accuracy 0.1 mm Turning angle of grinding stone ±90° Spindle revolution 4100r/min Grinding stone feeding stroke 42 mm Profile wheel span 1000 mm Weight 100 kg Weight of supporting rod 14 kg
NCM-5.1 Rail Switch Grinding Machine NCM-5.1 frog and switch grinder is specifically designed for grinding operations through switch and crossings and either side of the rail head. The grinding device of the machine can be tilted by 30° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency. It has the characteristics of precise turning and positioning at any position and angle of the turmout rail head. Specification Model NCM-5.1 Type Rail Grinding Machine Material Stainless Steel Dimensions (L x W x H) (mm) 2100*1120*1030mm Engine Honda GX270 Petrol engine Rated power 5.1kW Grinding wheel speed 3600r/min Grinding wheel feeding stroke 80mm Feed adjustment accuracy l0mm Grinding wheel rotation angle 30° Weight 117kg
Constant-fluron PTFE particle resin G401 is a free-flowing white powder composed of relatively large particles that is ideal for isobaric molding. Its most unique features are improved moldability at lower pressures and improved surface smoothness of finished parts. PTFE G401 is often used to form thicker sheets, and sometimes for the stamping of rods and pipes with thicker cross sections. Properly processed products made from high purity PTFE G401 have the superior properties typical of fluoroplastic resins Processing suggestion Fluoron PTFE is processed in two steps: preforming and sintering. The powder is first pressed into a preformed shape close to the desired molded product and then consolidated at temperatures higher than the melting point of the pure powder crystal using precise heating (sintering) and cooling cycles. The performance of the finished product depends on the bottle failure pressure, sintering time and temperature, and cooling rate. PTFE is used to make relatively large objects in molds that can be manually filled. Small particles of resin do not flow properly in the automatic feeding system.
Replacement Pall high flow cartridges are made of deep fine polypropylene or glass fiber membrane as filter media, with a large diameter of 6 inches / 152mm, no center rod, unidirectional opening, and specially designed to flow the liquid from the inside to the outside, ensuring that all contaminant particles are trapped inside the cartridge. The ultra-high flow rate design allows for a significant reduction in the use of cartridges and filters for the same flow rate application, resulting in significant savings in equipment investment costs and labor costs. Replacement P-all Model HFU620UY400H13W HFU640GF100H13 HFU620UY200H4W HFU640GF200H13 HFU620UY200HW HFU640GF100H13W HFU620CAS010JUW HFU660UY020J HFU620GF100H13 HFU640UY045J HFU620UY020H13 HFU640UY100J HFU620UY200J HFU640UY200J HFU620UY400J HFU660UY400H13 HFU620UY700J HFU660UY200H4 HFU620UY020J HFU660CAS010JUW HFU640UY020J HFU660GF050H13 HFU640UY045J HFU660GF100H13 HFU640UY100J HFU660UY060H1 HFU640UY200J HFU660UY1000H4W HFU640UY400H13 HFU660UY200H4W XLDM30-20U-HFJ XLDM4.5-40U-HFJ XLDM70-20U-HFJ XLDM10-40U-HFJ PFTM1-20U-HFH13 PFTM1-20U-HFH13U PFTM1-40U-HFH13 PFTM1-40U-HFH13U PFTM1-60U-HFH13 PFTM1-60U-HFH13U PFTM3-40U-HFHU PFTM3-40U-HFJ PFTM70-40U-HFHU PFTM70-60U-HFHU PFTM90-40U-HFHU PFTM90-60U-HFHU PFTM150-40U-HFHU PFTM150-60U-HFHU
Fowler bed with detachable Head and Foot bows. Size: 2060 mm L X 900 mm W X 600 mm H Backrest Tilt: 0 - 75�°, Knee rest Tilt: 0 â?? 35�° Backrest and Knee rest positions are maneuverable by smooth crank mechanism with separate folding SS Handle. Epoxy coated Mild Steel Structure with 4 sections made of CRCA Sheet. Provided with Single wheel heavy duty Diagonal Locking Castors Dia 100 mm for smooth mobility Fowler bed with detachable Plastic Head and foot bows. Size: L 2060mm �? W 900mm �? H 600mm Back rest 0-75�º, Knee rest 0-35° Epoxy coated mild steel structure with 4 section mattress platform made up of CRCA M.S. Sheet. 2 Separate crank mechanisms for back rest and knee rest respectively. Stainless Steel drop down side rails. Provision for I.V. Rod on four locations. 125mm Dia. castors 2 with brake
Place of Origin Hubei, China Type Rail switch grinding machine Material Stainless Steel Dimensions (L x W x H) (mm) 2100*1120*1030mm Brand Name Linkage Product name Rail switch grinding machine for track maintenance function Rail switch point grinding Engine Honda GX270 Petrol engine Grinding wheel speed: â?¥3600r/min Feed adjustment accuracy: â?¤l0mm Weight â?¤117kg Rated power: 5.1kW Grinding wheel feeding stroke: â?¥80mm Grinding wheel rotation angle: â?¥30�° NCM-5.1 frog and switch grinding machine is specifically designed for grinding operations through switch and crossings and either side of the rail head. The grinding device of the machine can be tilted by 30�° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency. It has the characteristics of precise turning and positioning at any position and angle of the turmout rail head.
NGM-5.1 Rail Profile Grinding Machine This machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polishing efficiency. BENIFITS â?? Angle of the grinding head is set using an adjustment wheel, lowering/raising of the grinding stone is electrically contlled â?? Equipped with spark protection device â?? Equipped with electric control system prevents over grinding by limiting the lowering of the grinding stone â?? Grinds the whole head of rail in one single operator, no need to turn the machine or to handle it Specification Model NGM-5.1 Type Rail Profile Grinding Machine Material Stainless Steel Dimensions (L x W x H) 1500 * 450 * 750 mm Engine HONDA GX270 Power 5.1 kW Grinding wheel specifications �?125x65 mm Feeding accuracy 0.1 mm Turning angle of grinding stone �±90�° Spindle revolution 4100r/min Grinding stone feeding stroke 42 mm Profile wheel span 1000 mm Weight 100 kg Weight of supporting rod 14 kg
Portable Rolling Track Gauge is mainly used for railway track gauge and superelevationcant check rail gauge and back to back distance measurementIt can be used for track inspection and fine adjustment of rail gaugeThis product has the advantages of fast measuring speed stable pushing rod easy to carryand nighttime and tunnel worklegible even in direct sunlight are supportedIt is an ideal measuring tool for track finetuning track constructioninspection and track laying Features The benefits of our rolling gauge 1 Measure the track gauge cant without bend over your back 2 Light weight around 65kg one person operation 3 BT connection data uploading and analysis system 4 High working efficiency Save your man power 1 man with 1 rolling gauge 4 man with 4 normal digital track gauge Specification Model 1435mm GJCJJG0 Track gauge 14101470mm Superelevation measuring range 185185mm Display mode OLED display and handheld terminal display Supply Voltage DC34V52V rechargeable battery Superelevation division value 005mm Working temperature 3055 Insulation performance 1M Track gauge division value 001mm Superelevation division value 005mm Track gauge max indication error 025mm Superelevation max indication error 03mm Length1700mm Net Weight 65kg
Sumip produces a wide range of fiber-reinforced polymer or reinforced plastic (FRP) products, manufacturing process: CNC Filament winding, pultrusion process and centrifugal casting. Innovating continuously, Sumip brings advanced solutions that often outperform conventional materials in the most critical and demanding applications. The Organisation's commitment to providing superior quality solutions, has led to the engineering of some of the most modern & effective fiberglass lighting products that are both innovative and economical, making it optimal choice of street light/platform/solar lighting poles needs across the globe. Features: Manufacturing Process: Filament winding, Pultrusion, Centrifugal Electrical Shock Resistance: Yes, Due to electrically non-conductive, it is Electrically Shock Resistant Corrosion Resistance Is It Waterproof EMI/ RFI Transparency: Transparent to radio waves and EMI/ RFI Transmission Aesthetics: From Simple to Designer/ Decorative Poles also available Accessories: Brackets,Junction Boxes, Mounting plates Other: Zero maintenance, High Strength, Highly Safe, Light Weight Installation Type: Anchor type- This type is installed on ground using base plate and fittings Burial type- This type is installed on ground burying little bottom portion of the Pole with anti- rotating rods for proper fixing
Welding and Track Maintenance Equipment Gas Pressure Rail Welding Machine Hydraulic rail weld trimmer/Hydraulic Rail shear Itâ??s A Special Small Size Machine Suitable For Shearing Thermit Weld Seam.Hydraulic Opreation,Save Labour,Shearing Clean. Itâ?? S Suitable For Dealing With Various Rails (50-75kg/M) At The Depot Or On The Track. Itâ??s An Accessory Tool In Cwr Laying Project, Rail Stress Releasing Operation And Broken Rail Repair.HWS-II Hydraulic Rail Trimmer Is Mainly Composed Of Machine Frame, Manual Pump Station, Two Horizontal Oil Cylinders, Guiding Device, Shearing Knife, Etc,. While Working, Ride The Machine On The Rail (At The Both Side Of The Seam), Place The Guiding Device Nearby The Rail Jaw, Then Swing The Manual Pump Handle Back And Forth. Along With The Cylinder Piston Rod Reaching Out, The Shearing Knife Makes Relative Motion To Produce Shear Force And Remove The Seam Bead.
Railway Hydraulic Rail Tensor for Rail Stretching Hydraulic Rail Tensor Itâ??s suitable for 75kg/m and 60kg/m type rail stress relief and seamless long rail relaying. While operating in the field at a certain temperature range being lower than the rail locking temperature, by employing this machine, the length of a rail with zero-stress can be forced to stretch to a length at locking temperature, then re-lock the rail. SPECIFICATION Model YLS-900I Material Stainless Steel Dimensions (L x W x H) (mm) 1300*690*240mm Max. rated working pressure 57Mpa Max. rail pulling force 2*450kN Max. stroke of working cylinder â?¥500mm Two pull rod center distance 535mm Lock mode wedges clamp on both sides of rail head Pump model Honda GXV160 Power 3.05kW Rate of flow 3L/min Machine weight 283kg Internal combustion pump station weight 75kg (not including pipeline)
