Granule 1~3mm Light yellow 99.9% 3~5mm 1~3mm Black 3~5mm Tablet Φ9x5mm Light yellow Φ10x6mm Φ9x5mm Black Φ10x6mm
Purity range: 99.5%, 99.9%, 99.95%, 99.99%, 99.995%, 99.999% Density: 80%~100% Size and shape: Round, Rectangle,Tube, Rod,wire,Granule,Pellets,crucible, boat 1inch diameter ~ 12 inch diameter(round shape) Max length: 1700mm, Max width: 300mm (Rectangle) Min thickness 0.1mm(Foil) Min diameter: 0.1mm(wire) Crucible: 4cc Pellets: 2*2mm, 3*3mm,6*6mm Production method: Vacuum melting,Powder hot pressing ,Powder sintering ,vacuum coating, Hot isostatic pressing(HIP), Vacuum extrusion, Forging, Line cutting , Milling and Polishing with ISO9001 quality management system
Element Symbol: Ti Purity: 3N, 4N, 4N5, 5N Availble Shape: Planar target, Rotary target
14mm/18mm double adjustable titanium nail 1.Materials: Gr2 pure titanium 2.Joint Size: 14mm /18mm 3.Weight: about 25g per piece 4.Progress: CNC 5.Surface: Polished 6.Application: Smoking 7.Ti Content (%) :99.96%
Titanium exhaust tubing is characterized by its lightweight, high strength, corrosion resistance and heat resistance. The density of titanium alloy is only 60% of steel, but the strength is even better. At the same strength, the titanium exhaust tubing is lighter than stainless steel, suitable for race cars and motorcycles owners who pursue the ultimate lightweight modification. Titanium Seamless Tube is a long strip of tubing made of titanium alloy with a hollow section and no seams around it. It was originally used primarily for the manufacture of aircraft engine compressor components and structural components for rockets, missiles and high-speed aircraft. Since the mid-1960s, it has been gradually applied to electrodes in the electrolysis industry, condensers in power stations, heaters for oil refining and seawater desalination, and environmental pollution control devices. The titanium welding pipe is obtained by welding a titanium or titanium alloy coiled strip or a wide-width sheet into a tubular shape by crimping. It has been widely used in electric power, seawater desalination, water treatment equipment, air conditioning equipment and other industries, but in the petrochemical industry, the use of titanium welded pipes is still being promoted.
china coal0001 DWQ Titanium Alloy Roof Single Hydraulic Acrow Prop Introduction of DWQ Titanium alloy Single Hydraulic Mining Roof Prop DWQ Titanium alloy Single Hydraulic Mining Roof Prop will become the ideal replacement products of existing high column series. The product is made of high-titanium alloy steel as raw material, stainless steel as inner cylinder, live column and other key components all use special anti-corrosion treatment, advantages of light weight, high strength, good toughness, impact resistance, corrosion resistance and so on. Water can be used instead of emulsion which saving a lot of cost. Compared with the DZ type prop, the same height and same strength of the single hydraulic prop weight only 25%,of DZ seriess props. Application of DWQ Titanium alloy Single Hydraulic Mining Roof Prop DWQ Titanium alloy Single Hydraulic Mining Roof Prop is suitable for mining and blasting work surface use, especially for the use of large slope of the face. DWQ Titanium alloy Single Hydraulic Mining Roof Propâ??s successful development is real realization of the high pillar monomer ultra-light high-strength. Features of DWQ Titanium alloy Single Hydraulic Mining Roof Prop 1, Long working stroke , especially for large height variation face of underground roof. 2, Apply inner bore seal bump- resistance in the underground, with a wide range of use. 3, Never broken. Using friction welding, the weld is not broken. 4, Uses a new sealing device, remove the DZ-type pillar between the piston and plunger leakage point, safe and reliable. 5,Level of support available. 6, High strength, no bend. Parameter of DWQ Titanium alloy Single Hydraulic Mining Roof Prop ModelMax Height(mm)Min Height(mm)Application Height(m) DWQ35350027003.0ï3.8 DWQ31.5315023502.65ï3.45 DWQ28280020002.3ï3.1 DWQ25250017002.0ï2.8 DWQ22224014001.7ï2.5 DWQ20200012351.5ï2.3 DWQ18180011051.3ï2.1 DWQ16160010001.1ï1.9 DWQ1414008950.9ï1.7 DWQ1212007870.8ï1.5 DWQ1010006800.7ï1.3 DWQ088005730.6ï1.1
Property: Smaller particle size: only 5nm and do not reunite with each other. Effective dispersal capacity. Higher catalytic activity. Higher cost performance. Antibacterial function :the product can not only kill bacteria, viruses nearly 650 kinds of bacteria ; but also decompose residues of bacteria, viruses by photocatalytic Specification Item no: jr05 Appearance: white or yellow powder Appearance of powder dissolved in water: transparent liquid Particle size: 5nm Purity: 99.9% Surface property: hydrophilic Application: 1.Widely used in the field of newly decorated living room, offices, hospitals, clinics, hotels, public places. 2. Suitable for top-grade coating and carpet, walls, wood furniture, leather, plastic, cloth, ceramics and glass. 3.The product can be coated on the surface of engine, exhaust pipe, transformation device of cars to separate co, nitrogen oxides to reduce pollutants produced by cars. 4.The product can be used in the field of concrete: add some powder of the product in cement to gain concrete, the pollutants in the air will be absorbed on the surface of concrete, then the nano titanium dioxide will do the function of removing the pollutants , purifying air and sterilization. 15kg/drum
NB Series Bar Diameter . The bar feeder is especially ideal for small precision parts, such as watch parts, electronic parts and so on. . Double clamping device provides positively material clamping and releasing. . Spiral workpiece infeed system requires no further adjustment when changing bar sizes. . Heavy weight feeding system increases stability of feeding. Standard wooden case/crate
SQKValves VALVES has extensive experience in manufacturing Trunnion Mounted, Side & Top Entry Ball Valves, both Soft and Metal Seated. Size: 2" up to 56" (DN 50 up to DN 1400) Pressure Rating: ASME 150# to 2500# Materials: Carbon Steels, Low Temperature Carbon Steel, Martensitic Steels, Austenitic Stainless Steel, Duplex Stainless Steels, Super Duplex Stainless Steels,Alloys, Nickel Aluminum Bronze, Hastelloy, Inconel, Titanium Alloy & Carbon Steel with Internal Corrosion Resistant Alloy (CRA) Overlay Design Standard: API 6D,API 608 Pressure / Temperature Rating: ASME B 16.34 Test (Inspection) Standard: API 6D,ISO 5208 API 6FA,ISO 10497, API607, BS 6364 Construction Details: Single / Two / Three Piece Design / Side Entry End Connection: Flanged,Butt-Weld Operator / Actuator: Lever, Gear, Actuator (Pneumatic, Hydraulic, Electro-Hydraulic and Electric Motorised) Special Design Feature also available: Cryogenic Design Subsea Design Stem Extension Single & Double Piston Seat Design Primary Metal and Secondary Soft Seat Design Emergency Seat and Stem sealant Injection
One Step Influenza A Test is a rapid qualitative assay that detects influenza type A (including the subtype H1N1) nucleoprotein antigen extracted from the nasal swab specimen. The device is used to aid in the diagnosis of influenza type A infection. For in vitro diagnostic use only. For professional use only. Influenza A SUMMARY Influenza (commonly known as flu) is a highly contagious, acute viral infection of the respiratory tract. It is a communicable disease that is easily transmitted through the coughing and sneezing of aerosolized droplets containing live virus. Influenza outbreaks occur each year during the autumn and winter months. There are three types of influenza viruses: A, B, and C. Only influenza A viruses are further classified by subtype on the basis of the two main surface glycoproteins hemagglutinin (HA) and neuraminidase (NA). Influenza A subtypes and B viruses are further classified by strains. Humans can be infected with influenza types A, B, and C viruses. Subtypes of influenza A that are currently circulating among people worldwide include H1N1, H1N2, and H3N2 viruses. Influenza B viruses can cause morbidity and mortality among humans, but in general are associated with less severe epidemics than influenza A viruses. Although influenza type B viruses can cause human epidemics, they have not caused pandemics. Influenza type C viruses cause mild illness in humans and do not cause epidemics or pandemics. Influenza A PRINCIPLE One Step Influenza A Test is a rapid immunochromatographic test for the visual detection of influenza type A antigen (nucleoprotein) extracted from the nasal swab specimen. The test adopts double antibody sandwich method. When the extracted specimen is added into the test device, the specimen is absorbed into the device by capillary action, mixes with antibody-dye conjugate, and flows across the membrane pre-coated with influenza type A monoclonal antibody. When the influenza type A antigen levels are at or above the target cutoff (the detection limit of the test), type A antigen in the specimen binds to the specific antibody-dye conjugate and are captured by influenza type A monoclonal antibody immobilized in the relative site of test region T of the device. This produces a colored test band in the test region. When the influenza type A antigen levels are zero or below the target cut off, there is not a visible colored band in the test region of the device. This indicates a negative result for influenza type A.
Medical Goggles Anti Mog,anti-dust,anti-sling,anti Fog, Uv-protection Product Description : Environmental friendly PVC Frame,4 indirect air-vents, injection molding PC lens, excellent transmittance, clear/grey/yellow/blue/other lens for choices, Elastic headband, comfortable to wear, suitable for occassions with chemical spatter, particles impact and dust, Quality Standard: Ansiz87.1&CE EN166&FDA Price of product ( USD price or FOB price) : FOB CHINA USD1.65 Product origin : NANCHANG CITY, JIANGXI, CHINA Key Specifications/Special Features : Eye-cover medical anti-mog goggles AJ2002; Material: PC+PVC. Spec: 190*70mm. Color: light Green. Procedure: Double sides anti-mog. Standards executed: GB14866-2006. Medical device Minimum Order Size and Packgaing details : 10 Cartons Packing Details : single P.P bag each, 200pcs/Carton,Gross weight 15kgs/carton, carton size: 58*38.5*43cm
* Protection for people and workers who place great value on facial expressions such as children, people with hearing problems, police forces and nurses, The mask can be used also as non-sterile mask in hospitals and vaccine centres. No fogging of glasses thanks to extra soft nose pads. * Colour: Black and white * Size: Standard and children * Box: 50 pieces * Price per box: CHF 53.75 * Languages: Italian, French, German, * Brand: ST-Cleantech AG * English, and Spanish Price range: < 29 boxes -> CHF 53.75 > 200 boxes -> CHF 8.40 > 30 boxes -> CHF 52.70 > 500 boxes -> CHF 45.70 > 100 boxes -> CHF 51.10 First layer non-woven: White or Black: 50g (double S) Second layer: 25g melting spray cloth Third layer non-woven: White or Black: 25g (double S) Layer 4 PP transparent sheet: Thickness: 0.33mm +/- 0.1mm Size: 134mm x 37mm +/- 2mm Material: PP Classification /Standard: Medical device: Class I / according to DIN EN14683:2019. Duration: 2 years Material: Consisting of: non-woven fleece layer PP, filter material PP manufactured in meltblown process, PP window (13.4x3.7x0.2 cm) ultrasonically welded latex-free, nose clip, aluminium wire PE coated, ear bands made of elastane. Level of performance: Filter efficiency antibacterial : (BFE) Respiratory resistance : Resistance to pressure spray: Microbiological purity : According to type IIR (same test standard to be applied). Norm: 98% - Test result: 99.9%. (according to EN 14683:2019+AC:2019, Annex B). Standard:
Syphilis Test INTRODUCTION Anti-Syphilis Test is a rapid direct binding test for the visual detection of anti-syphilis antibodies in serum as an aid in the diagnosis of syphilis infection. Test results are read visually without any instrument. It is based on the principle of double antigen sandwich immunoassay for determination of syphilis antibodies in serum. Purified recombinant syphilis antigens are employed to identify anti-Syphilis antibodies specifically. This one step test is very sensitive and only takes about 10 to 20 minutes. Syphilis Test SPECIMEN COLLECTION For serum, collect blood into a container without anticoagulant. Allow the blood to clot and separate the serum from the clot. Use the serum for testing. If the specimen cannot be tested on the day of collection, store the serum specimen in a refrigerator or freezer. Bring the specimens to room temperature before testing. Do not freeze and thaw the specimen repeatedly. Syphilis Test PROCEDURE Strip 1.When you are ready to begin testing, open the sealed pouch by tearing along the notch. Remove the test from the pouch. 2. Immerse the strip into the container with the arrow end pointing towards the container. Do not immerse past the MAX (maximum) line. Take the strip out after 8-10 seconds and lay the strip flat on a clean, dry, onabsorbent surface (e.g., mouth of the serum container). 3.Wait 10-15 minutes and read result. Do not read results after 20 minutes. Cassette 1. Open a pouch containing a cassette, lay the cassette. 2. Using the plastic pipettor provided, draw about 2-3 drops (100mL) the sample into the sample well of the cassette. 3. Read results within 10-15 minutes. Do not read results after 20 minutes. INTERPRETATION OF RESULTS Negative: Only one pink band appears on test region of the Cassette. This indicates that there is no detectable Anti-Syphilis in the serum. Positive: Two pink bands appear on test region of the Cassette. This indicates that the specimen contains detectable amount of Anti-Syphilis. Invalid: If without colored band appears on test region, this is an indication of a possible error in performing the test. The test should be repeated using a new device. Syphilis Test PRECAUTION: 1. Must use fresh specimen and avoid repetitive freezing, the result will be invalid 2. Use it before expiry date. 3.The package of kit should not be opened until it reaches the room temperature if it taken out from the refrigerator. 4 .Old Serum can not be used. If the serum is thick, it can be used only after being separated. Syphilis Test LIMITATIONS The test is for in-vitro diagnostic use only.
YT round circle self-fluorescent double sided road stud with reflective film Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF05 Product name YT round circle self-fluorescent double sided road stud with reflective film Material ABS+reflective film+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size Ï?100mmÃ?11mm Weight 88g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF05 (6)YF05 (2)YF05 (5)YF05 (6)YF05 (1)YF05 YF05 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
Hangzhou YT Self-illuminating ABS road stud d with strong visibility Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF22 Product name Hangzhou YT Self-illuminating ABS road stud d with strong visibility Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 100mmÃ?100mmÃ?20mm Weight 145g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF22 (2)_YF22 (3)YF22 (4)YF22 (3)YF22 (6)YF22 (2)YF22 (1)YF self-luminating series table of brightnessYetong road studplastic road stud_application
YT Nano-fluorescent self-luminous cat eye road stud delineator with glass beads Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF10 Product name YT Nano-fluorescent self-luminous cat eye road stud delineator with glass beads Material ABS+glass beads+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 110mmÃ?110mmÃ?66mm Weight 138g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF10 (2)YF10 (3)YF10 (5)YF10 (4)YF10 (1)YF10 (1)YF10 (3)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT Factory Energy Storage Self-luminous Highway Road Reflective Delineator as Traffic Signs Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF18 Product name YT Factory Energy Storage Self-luminous Highway Road Reflective Delineator as Traffic Signs Material Aluminium+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 150mmÃ?150mm Weight 48g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF18 (4)_YF18YF18__ YF18 (3)YF18 (2) YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT hangzhou energy storaged square self-luminous road stud with cat eyes Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF01 Product name YT hangzhou energy storaged square self-luminous road stud with cat eyes Material ABS+glass beads+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 130mmÃ?110mmÃ?15mm Weight 150g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF01 YF01 YF01 (4)YF01 (1)YF01 (5)YF01 (5)YF01 (3)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT yellow shell self-luminous rectangle reflector road studs with cat eye Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF03 Product name YT yellow shell self-luminous rectangle reflector road studs with cat eye Material ABS+glass beads+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 130mmÃ?110mmÃ?15mm Weight 165g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance yf03_YF03 (1)YF03 (9)YF03(8)YF03 (7)YF03 (4)YF04 YF03 (3)_YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
