HTM226LF Temperature and Humidity Sensor Module DESCRIPTION Based on the rugged HS24LF resisitive humidity sensor, HTM226LF is a dedicated humidity and temperature transducer designed for OEM applications where a reliable and accurate measurement is needed. It features a very small size for easy, cost-effective mechanical mounting. Direct interface with a micro-controller is made possible with the nodule's linear voltage output. HTM226LF Temperature and Humidity Sensor Module FEATURES * Full Lead free product * Calibrated within +/-5% @55%RH at 5Vdc * Small size and very cost effective * Miniature connector (JST) * 50kOhms +/-3% NTC temperature sensor @25'C * The best combination of cost effectiveness and performance * Stable, linear proportional voltage output from 0% to 95%RH * Stable and reproducible characteristics with temperature * High reliability and long term stability HTM226LF Temperature and Humidity Sensor Module APPLICATIONS * Air condition, Humidifier, Dehumidifier * Humidity controller, Humidity transmitter * Hygrometer, Hygro-recorder * Copying machine * Clock, Weather-forecast barometer
Pressure sensor module ms5803-14ba description: The pressure sensor module ms5803-14ba is a new generation of high resolution pressure sensors with spi and i2c bus interface. It is optimized for depth measurement systems with a water depth resolution of 1cm and below. The sensor module includes a high linear pressure sensor and an ultra low power 24 bit î?î£ adc with internal factory calibrated coefficients. It provides a precise digital 24 bit pressure and temperature value and different operation modes that allow the user to optimize for conversion speed and current consumption. A high resolution temperature output allows the implementation of a depth measurement systems and thermometer function without any additional sensor. The ms5803-14ba can be interfaced to any microcontroller. The communication protocol is simple, without the need to programming internal registers in the device. The gel protection and antimagnetic stainless steel cap protects against 30 bar overpressure waterproof. This new sensor module generation is based on leading mems technology and latest benefits from the intersemaâ??s proven experience and know-how in high volume manufacturing of pressure modules have been widely used for over a decade. This sensing principle employed leads to very low hysteresis and high stability of both pressure and temperature signal. Pressure sensor module ms5803-14ba features: * high resolution 0.2 mbar * fast conversion down to 1 ms * low power, 1ua (standby < 0.15 ua) * integrated digital pressure sensor * supply voltage 1.8 to 3.6 v * operating range: 0 to 14 bar, -40 to +85 'c * i2c and spi (mode 0, 3) * no external components (internal oscillator) * excellent long term stability * hermetically sealable for outdoor devices Pressure sensor module ms5803-14ba applications: * mobile water depth measurement systems * diving computers * adventure or multi-mode watches
Gas leak detection in stationary fuel cells combustible gas sensor module Model number:cgm6812--b00 Features: * linear analog output proportional to gas Concentration * maintenance free * compact size * meets rohs requirements Applications: * gas leak detection in fuel cell systems * hydrogen & combustible gas leak Detectors Description: The cgm6812-b00 combustible gas sensor module is A new unit which utilizes tgs6812, figaro's catalytic Pellistor type gas sensor which features durability and stability. This module provides analog output voltage proportional to hydrogen gas concentration. Cgm6812-b00 has conformal coatings for moisture- Proofing and electrical insulation purposes, and is also Capable of detecting sensor wire breakage. The unit has A wide range of operating temperature from -10' to +60'c. Because the tgs6812 sensor can detect methane and lp gas As well as hydrogen, this module is suitable for gas Leak detection in stationary fuel cells which use hydrogen Generated from combustible gases Sensor Module Cgm6812
Frequency output temperature and humidity module htf3223lf Model number: htf3226lf Description Based on the rugged hs1101lf humidity sensor, htf3223lf is a dedicated humidity and Temperature transducer designed for oem applications where a reliable and accurate measurement is Needed. It features a miniature connector for easy, cost-effective mechanical mounting. Direct interface With a micro-controller is made possible with the module’s linear frequency output. Main features -the best combination of cost effectiveness and performance -stable, linear proportional frequency output from 10 to 95% rh. -calibrated within +/- 5% rh @ 55% rh. -10 kohm +/- 3% ntc temperature sensor (1% optional) -stable and reproducible characteristics with temperature. -high reliability and long term stability. Humidity sensor specific features Instantaneous de-saturation after long periods in saturation phase. Fast response time. High resistance to chemicals. Not affected by water immersion. Patented solid polymer structure. Temperature sensor specific features High quality thermistor Stable High sensitivity
Features: Gas concentration is digitally and quantitively Output by means of communications Alarm output can be set through programming Factory calibrated, temperature compensated Compact size, low cost Applications: Front-end solution for methane gas alarm Simple methane gas alarm output Description Fsm-t-01 is a pre-calibrated module for methane gas alarm Which applies tgs2611 sensor together with optimized Classic circuit measuring methane gas concentration. The Module is pre-calibrated by figaro's highly accurate calibration Equipment and manufactured with mature aging process. The purpose of the module design is to save the development And production cost of the user to its greatest extent, making It easier and more convenient for them to manufacture gas Alarm for civil natural gas. The module is designed with two different interfaces Considering the convenience for use. Ttl level’s asynchronous Communication interface allows the user to read real time Gas concentrations with very simple commands;also different Alarm thresholds can be set through communication programming. When the gas concentration reaches set value alarm Output signal would be generated automatically from the Alarm terminal. Besides , this compact sized module applies a socket type Design which facilitates regular replacements of the sensors. For some main board, different modules can also be replaced Simply by plugging and pulling out, fulfilling the functions of Detection and alarming for methane and other gases.
DC Input Motion Sensor Module Standard Motion Sensor Module 5V/12V DC Input Microwave Motion Sensor - Standard Version HNS101D 5.8GHz C-band microwave, tri-level dimming function. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. Features 5.8GHz C-band microwave, tri-level dimming function. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 5V DC PWM output or 0~10V DC signal. Super compact, flexible to be integrated into any suitable fixtures. Dual-PD technology, real Dayligh t m onitoring function for built-in application. 8 pin DIP switch setting, multiple options to meet different customer demands. Detection range up to 12m in diameter. Mounting height: 3~6m. Operation temperature; -20? ~ + 70?. RoHS compliant. Settings Detection range Detection range can be reduced by selecting the combination on the DIP switches to fit precisely each application. Hold-time Hold-time means the time period to keep the lamp on 100% after motion detected. *when hold-time set as 3s, sensor enters into test mode, this test mode is mainly for users to choose the desired detection range. In this mode, the daylight sensor is disabled, when there is no motion, fixture keeps off, when there is motion detected, fixture keeps a cycle of 3s on and 2s off. Daylight sensor Daylight sensor means the daylight threshold to enable or disable the sensor function. "Disable": The sensor works always, even during daylight. w50lux": The sensor works only in twilight. w10lux, 2luxw: The sensor works only in the dark. Stand-by period This is the time period that the lamp remains at a low light level before it is completely switched off in the long absence of people. ?+? means bi-level dimming control, the fixture never switch off. Stand-by dimming level This is the dimmed low light level you would like to have after the hold-time in the absence of people. Daylight monitoring function Utilizing the Dual-PD technology, this sensor can tell the difference of natural light and artificial light(lamp) from behind the diffuser, switch on automatically(even without movements) when the ambient light is below target value, and then switch off automatically whenever the artificial light is not required(ambient light is bright enough). This is the REAL & INTELLIGENT daylight monitoring sensor for built-in installation. Note: Lux-Off sampling time?30s; Lux-On sampling time?10s. Lux-On function takes effect only when standby dimming period set at.
Pdsm010 particle sensor module product summary Pdsm010 detects approx. 1m particle such as house dust, pollen, germs, dust mites and cigarette smoke and measures the concentration of floating particles in a room space up to maximum 30m3. This sensor is an ideal product for automatic room air monitoring system such as an air purifier. Pdsm010's signal is converted to pwm output by internal circuit and mcu program. Also, the sensor's filter circuit and mcu program can remove a noise in order to operate more stably when a noise is in-flowed in the signal. Pdsm010 has advantages of both stable detecting ability and high manufacturing efficiency. The sensor does not have an additional control point (vr trimmer) on the device unlike its previous model (dsm). It prevents potential malfunction often occurred by user's arbitrary modification. Pdsm010 particle sensor module features * customized sensitivity for efficient control in application * detects approx. 1m particle * mcu control (factory calibration) * easy maintenance * pwm output (low logic pulse active) * noise protection Pdsm010 particle sensor module applications * air cleaners, air conditioners * ventilation system, fan control * iaq monitoring & control * iot device Pdsm010 particle sensor module product specification * supply voltage: 5v 10% v * supply current (@ 5v): < 85ma * storage temperature range: -20 ~ 80'c * operating temperature range: -10 ~ 65'c * operating humidity range: < 95%rh
Low power carbon dioxide sensor nrid co2 gas sensor cozir-a description Cozir is an ultra low power (3.5mw), high performance co2 sensor, ideally suited for battery operation and portable instruments. Based on patented ir led and detector technology and innovative optical designs, cozir is the lowest power ndir sensor available. Optional temperature and humidity sensing are available. Cozir is a third generation product from gas sensing solutions ltd ? leaders in ir led co2 sensing. With measurement ranges of 0-2000ppm, 0-5000ppm and 0-1% the cozir ambient sensor is suitable for applications such as building control and horticulture. * ultra-low power 3.5mw * measurement ranges from 0 to 1% * low noise measurement
HPD05 Infrared PM2.5 Sensor Module Product Details 1. Module List HPD05 Module 2. Product Overview HPD05 PM2.5 Sensor Module use principle of optical scattering to measure concentration of dust inthe air,the module built in a Infrared Transmitter and a high sensitive Photoelectric Receiving Sensor the Infrared Transmitter emits light and the light meets the dust to produce the scotch light, theintensity of the scotch light detected by Photoelectric Receiving Sensor reflects the concentration ofdust in the air, HPD05 have two ways to output current concentration data, one is PWM signal (thewidth of signal is the value, 1ms = 1ug/m3), the other is IIC signal(unit is ug/m3). HPD05 can be used for Air Cleaner, Air Conditioner with purifying function, Fresh Air System and air quality testing equipment. 3. Detecting Principle Detecting Principle Per the principle of optical scattering,the Transmitter emits light, and the light meets the dust to produce the scotch light, the high sensitive Photoelectric Receiving Sensor detects the intensity of the scotch light then output intensity signal, current which is proportional to the size and quality of intensity of the scotch light, the current is amplified by amplifier and calibrated by CPU, finally output digital PWM signal or IIC data of concentration of dust. 4. Performance Parameter 1 Characteristics Characteristics Connector CON2 Pin Description Connector CON2 Pin Description 2 Life Life of Light Source: above 5 years with continuous power on. 3 Photoelectricity Characteristics Photoelectricity Characteristics 4 Signal Output a1. PWM signal output(Corresponding Model HPD051Axxx): Signal Output The relation of Low Pulse Time and Dust Concentration: 1ms = 1ug/m3 The pulse width outputted by P1 pin is the average value of Dust Concentration(Lower responding speed, small fluctuation & good stability) The pulse width outputted by P2 pin is the insta
Low cost; 5.8GHz C-band miniature transceiver; Patch antenna, antenna gain:2 dBi. Beam aperture: 30º; 2 balanced mixer; 5dBm EIRP output power; Receiver bandwidth: 1Hz ~ 2KHz; Operating current(CW mode):13.5mA@5V; Low power consumption (Pluse mode); Average current:1.5mA typ. Pulse width (min.):10~50μs(10kHz~2kHz); Duty cycle:10% DC RoHS compliant Tested to EN300 400
FSM-10H-01 Pre-calibrated Module for LPG Gas FSM-10H-01 is Pre-calibrated Module for LPG gas alarm which applies TGS2610-D00 sensor together, it features durability and stability. The module outputs PWM signal which is proportional to LPG gas concentration (The module has a memory which is stored with factory calibration data), also is capable of detecting sensor wire breakage and short. The module can operate at wide temperature from -10~70'C. Furthermore, the unit is less sensitivity to VOCs gas, it immunes poison by silicon compounds, it suits to work at rugged environment. FSM-10H-01 Combustible Gas Sensor Module Features * PWM, USART digital output proportional to gas concentration * Maintain Free * Compact size, low cost * Meets RoHS requirement FSM-10H-01 Combustible Gas Sensor Module Applications * Detect flammable gas leakage * Flammable gas leakage Detector * Industrial detector FSM-10H-01 Combustible Gas Sensor Module Specification * Gas sensor: TGS2610-D00(Semiconductor) * Detection range: 0 ~ 4,000ppm H2 * Error: ± 300ppm * Response time (T90): �30S * Operation temperature: -10'C ~+70'C * Operation humidity: 20~95%RH(No condensing) * Input voltage (VIN): 5.00.2V DC * Power consumption: 15W
Fsm-t-04a combustible gas sensor module description The fsm-t-04a combustible gas sensor module is a new unit which utilizes tgs6812, catalytic pellistor type gas sensor which features durability and stability. This module provides analog output voltage proportional to hydrogen gas concentration.(there is a memory in module, where factory calibration data has been store). Fsm-t-04a has conformal coatings for moisture proofing and electrical insulation purposes, and is also capable of detecting sensor wire breakage. The unit has a wide range of operating temperature from -10 to +70'c. Furthermore, the unit can detect ch4, lpg, h2. It is less sensitivity to vocs gas, it immunes poison by silicon compounds, it suits to work at rugged environment. Fsm-t-04a combustible gas sensor module features: * linear analog output proportional to gas concentration * maintenance free * compact size * meets rohs requirements Fsm-t-04a combustible gas sensor module applications: * gas leak detection in fuel cell systems * hydrogen & combustible gas leak detectors Fsm-t-04a combustible gas sensor module specification * gas sensor: tgs6812 (catalyâ??tic type) * detection range: 0 ~ 50, 000ppm ch4 * error: 3%lel * response time (t90): 30s * operating temperature: -10'c ~ +70'c * operating humidity: 20~95%rh (no condensing) * input voltage: 5.00.2v dc, 3.00.1v dc * power consumption: 1.5w
HG-P40C Ultrasonic Proximity Sensor & Module Description * Using only a single transceiver sensor unit for transmit and receive signals. * Convenient for distance measuring and object detection. * Two types of transmit mode for convenience. - Free Run : With a power supply, sensor transmits trigger and burst signal itself - for basic application - External Trigger : External system(controller or processor circuit) controls the trigger signals - for advance application(distance measure) * Two types of input power - Low(5V) for processor circuit usage and High(12V) for controllers. * Four different output signal (simultaneously). - Real time ultrasonic wave amplified from actually received ultrasonic. (for sound pressure measuring) - Real time TTL level square signal(Square Wave) of detection signal. (for robots) - Distance pulse width signal which is proportional to the nearest object from the sensor. (for robots and distance measuring) - Proximity output signal(10mA current) within the preset range(0.5~4.5m) (for industrial use) - Preset range is adjustable from 0.5 to 4.5 m. (factory distance preset available for volume orders) * High performance ASIC Chip for stable transmission and sensitive reception. (Max. approx. 4,000 times amplification) HG-P40C Ultrasonic Proximity Sensor & Module Features * Multi functional transceiver model * Two types of transmit modes (Free Run / External Trigger) * Power Supply (Low : 5V / High : 6~16V) * 4 different output signals (simultaneously) - Real time received and amplified ultrasonic wave - Real time TTL square signal - Distance pulse width signal - Detecting objects within the preset range(proximity) * High performance ASIC Chip HG-P40C Ultrasonic Proximity Sensor & Module Specification * Input DC: Low : 5V / High : 6~16V * Current consumption (when 12V is used) - 12mA (Standby Mode) - 18mA (When an object is detected within the range) - 28mA (Proximity signal 10mA deducted) * Distance Range (at flat plate) - 0.4~3m (when 5V is used) - 0.4~6m (when 12V±3V is used) * Size Module : 20x36x20(mm) Sensor : Φ16
HG-P40C Ultrasonic Proximity Sensor & Module Description * Using only a single transceiver sensor unit for transmit and receive signals. * Convenient for distance measuring and object detection. * Two types of transmit mode for convenience. - Free Run : With a power supply, sensor transmits trigger and burst signal itself - for basic application - External Trigger : External system(controller or processor circuit) controls the trigger signals - for advance application(distance measure) * Two types of input power - Low(5V) for processor circuit usage and High(12V) for controllers. * Four different output signal (simultaneously). - Real time ultrasonic wave amplified from actually received ultrasonic. (for sound pressure measuring) - Real time TTL level square signal(Square Wave) of detection signal. (for robots) - Distance pulse width signal which is proportional to the nearest object from the sensor. (for robots and distance measuring) - Proximity output signal(10mA current) within the preset range(0.5~4.5m) (for industrial use) - Preset range is adjustable from 0.5 to 4.5 m. (factory distance preset available for volume orders) * High performance ASIC Chip for stable transmission and sensitive reception. (Max. approx. 4,000 times amplification) HG-P40C Ultrasonic Proximity Sensor & Module Features * Multi functional transceiver model * Two types of transmit modes (Free Run / External Trigger) * Power Supply (Low : 5V / High : 6~16V) * 4 different output signals (simultaneously) - Real time received and amplified ultrasonic wave - Real time TTL square signal - Distance pulse width signal - Detecting objects within the preset range(proximity) * High performance ASIC Chip HG-P40C Ultrasonic Proximity Sensor & Module Specification * Input DC: Low : 5V / High : 6~16V * Current consumption (when 12V is used) - 12mA (Standby Mode) - 18mA (When an object is detected within the range) - 28mA (Proximity signal 10mA deducted) * Distance Range (at flat plate) - 0.4~3m (when 5V is used) - 0.4~6m (when 12V±3V is used) * Size Module : 20x36x20(mm) Sensor : Φ16
HG-C40U Ultrasonic Range Finder Sensor & Module Description * ATmega 8 MCU * Measures distance from the obstacle and sends the data using UART communication. * Within 5mm Resolution * Optional two transmitting mode for various use. - Free Run : With a power supply, sensor transmits trigger and burst signal by itself (for basic application) - External Trigger : External system(controller or processor circuit) controls the trigger signals - for advance application * Two types of input power - Low(5V) for processor circuit usage and High (12V) for controllers. * Factory Default : 12V * Various Setting Option - Free Run / UART Trigger / External Trigger setting - Ring buffer use or not use setting - UART communication baudrate setting - Free Run Trigger interval * Output Signal - Distance Data using UART(ASCII, mm) - Real time ultrasonic wave amplified from actually received ultrasonic. - Real time TTL level square signal(Square Wave) of detection signal. * High performance ASIC Chip for stable transmission and sensitive reception. * Sensor to PC communication using 'Interface Board' (RS232, Power regulator) * Data display using monitor program from PC (Hyperterminal available) HG-C40U Ultrasonic Range Finder Sensor & Module Specification * Communication: UART(TTL) * Input Voltage 5V, 12V(default) * Current Consumption: 20mA(Typ) ~ 30mA(Max) * Frequency: 40kHz * Max. distance: 3.5m (at 5V); 5m (at 12V) * Min. distance: 2cm * Resolution: 5mm -
Dust sensor module dsm501b description Dust sensor module: dsm501 series detects the level of indoor airborne dust, particles, and pollen, and ideal for use in stand-alone air cleaner or iaq monitor. Pwm output of the sensor can be directly connected to î¼-com to control fan speed or ventilation and also to display the level of particles. Detectable size of particle is limited to minimum 0.7 um, and the application for smoke or fire alarm is prohibited. Dust sensor module dsm501b type: Dsm501a : 2mm pitch connector type (20010wr-05). Dsm501b : 2.5mm pitch connector type (s5b-eh). Dust sensor module dsm501b electrical characteristics: Supply voltage: dc510% Power consumption: 90ma Operating temperature range: -10~ +65'c Operating humidity range: 95%rh or less (without dew condensation) Recommend storage condition: -20 ~ +80'c Dimension: w59 * h45 * d20 (mm) Detectable particle size: approx. 1um (minimum) Detectable range of concentration: 0 - 1.4mg/m3 Output signal: pwm (pulse width modulation) Time for stabilization: 1 minute after power turned on Sensor characteristics: to be maintained in between the upper limit and lower limit of the standard dust sensor unit Dust sensor module dsm501b features: * pwm output * easy installation * single power supply * compact size and lightweight Dust sensor module dsm501b application: * ventilator etc * air conditioner * air quality monitor * air cleaner or air purifier
Factory calibrated methane sensor module for methane sensor tgs2611 Model number: ngm2611 Features: * factory calibrated * temperature compensation circuit * low power consumption sensor tgs2611 * compact size * meets rohs regulations Applications: * residential natural gas alarm Description The ngm2611 is a pre-calibrated module for natural gas alarms which is precisely Calibrated in figaro's humidity and temperature controlled facility. The most important process in manufacturing reliable resdential gas alarms is Adjusting the alarm point. Calibration is a complicated and time consuming Process which also requires a substantial investment in calibration equipment. By Eliminating the costly calibration process, this module enables users to easily and Simply manufacture residential natural gas alarms. Figaro has taken the complexity Out of designing a gas detector circuit by providing users with a temperature Compensation circuit which combines a built-in thermistor and individually adjusted Load resistor together with figaro’s low power methane gas sensor. A connector allows easy replacement of the module for the purpose of periodic Sensor renewal. This input/output connector enables easy installation of the Module into the gas detectors’ mother board. This same mother board can be Used for both methane and lpg gas detectors by simply changing the module. This module is designed to meet the performance requirements of en50194, and ul1484. Please refer to “technical information for tgs2611” for sensor sensitivity characteristics. Refer to “application notes for tgs2611” for further information regarding circuit design.
IRC-A1 Infrared Carbon Dioxide (CO2) Sensor Description Alphasense CO2 and Methane infrared sensors are supplied in the industry standard miniature (20mm diameter) gas sensor housing. Patented optics give the best signal to noise ratio of any 20mm diameter NDIR and universal linearisation constants allow easy implementation. The on-board temperature sensor allows for software compensation, including ideal gas law correction. CO2 The IRC-A1 with dual channel pyroelectric detector. This CO2 sensor is designed for IAQ, safety, combustion and high CO2 process control applications. Application notes explain linearisation, temperature compensation and circuitry. The IRC-A1 cover the entire concentration range of measurement, simply implement the appropriate linearisation constants in software for your required range: IAQ: 0 to 5,000ppm CO2 Safety: 0 to 5% CO2 Combustion: 0 to 20% CO2 Process control: 0 to 100% CO2 Matched Transmitter board for IRC-A1 Infrared CO2 Sensor IRC-TX NDIR CO2 Transmitter Board Features * Both 4-20mA and USB output * Uses Alphasense IRC-A1 NDIR cell * Adjustable bulb voltage to optimise long-term stability vs. resolution
IRC-AT Infrared Carbon Dioxide (CO2) Sensor Description Alphasense CO2 and Methane infrared sensors are supplied in the industry standard miniature (20mm diameter) gas sensor housing. Patented optics give the best signal to noise ratio of any 20mm diameter NDIR and universal linearisation constants allow easy implementation. The on-board temperature sensor allows for software compensation, including ideal gas law correction. CO2 The IRC-AT with dual channel thermopile detector. This CO2 sensor is designed for IAQ, safety, combustion and high CO2 process control applications. Application notes explain linearisation, temperature compensation and circuitry. The IRC-AT cover the entire concentration range of measurement, simply implement the appropriate linearisation constants in software for your required range: IAQ: 0 to 5,000ppm CO2 Safety: 0 to 5% CO2 Combustion: 0 to 20% CO2 Process control: 0 to 100% CO2 * IAQ Range: 0 to 5000ppm * Temperature Signal : Integral thermistor * Response Time (t90): < 40 s @ 20'C ambient * MTBF: > 5 years * Operating Temperature Range: -20 to +50'C * Storage Temperature Range: -40 to +75'C * Humidity Range: 0 to 95% rh non-condensing
Cozir ambient sensor Ultra low power carbon dioxide sensor Cozir is an ultra low power (3.5mw4), high performance co2 sensor, ideally suited for battery operation, portable instruments and hvac.Based on gss ir led and detector technology, and innovative optical designs, the cozir offers the lowest power ndir sensor available.Optional temperature, humidity and light sensing are available.Cozir is a third generation product from gss - leaders in ir led co2 sensing. With measurement ranges of 0-2000ppm, 0-5000ppm and 0-1% the cozir ambient sensor is suitable for applications such as building control and horticulture. * ultra-low power 3.5mw * measurement ranges from 0 to 1% * low noise measurement -
