150T-200T Aluminium Sheet Rolling Mill Material: Aluminium Scrap Finished product: Aluminum sheet width 200mm-940mm, Thick 0.6 ~ 1.6mm, Output: 150-200 tons per month , Medium frequency furnace (1 ton) , The main machine: 400 X 1300 two rollers reversible rolling mill , Screwdown mode: single stage screwdown drive, manual clutch , Screwdown motor: Y 6 N =4.5 KW, 2 units, with screwdown, lifting at the same time .Also can be respectively screwdown, lifting. Center distance of screwdown worm gear box: A=270mm, Screw-down adiusting screw S150 X 10, material: 40 Cr, Screw-down display: screwdown the indicator. Mechanical alignment guide device before the machine and after the machine Motor 3KW} JZQ250 reducer, Roll size: 400 X 1300, Roller specifications 120 X 1300, pitch: 170 H-shaped rolls , The electric control cabinet to motor operation box to the cable, electrical wires between the control line and installation accessories by The buyer is responsible for themselves. The equipment lubrication station, the supplier provides pipeline layout, the connecting pipeline under the machine, The equipment covers an area of 30m X 15m , The above technical parameters for aluminum sheet Rolling.
Cold mill is a new type of cold steel mill processing equipment. The machine can be hot rolled wire rod diameter between 6.5 mm to 12 mm, hot rolled disc circle processing into the finished product specifications diameter of 5 mm to 12 mm cold rolled ribbed steel bar. The cold-rolled ribbed steel bar rolled by cold rolling mill is the replacement of cold-drawn low carbon steel wire in prestressed concrete members. In cast-in-place concrete structures, the grade I steel bar can be replaced to save steel. It is a better kind of cold-worked steel in the same kind. If speed regulation is not required in the process of cold rolling mill, AC motor can be used; If speed regulation is needed in the process of cold rolling mill, DC motor can be used.
Hot rolling mill is made of continuous casting slab or first rolled slab as raw material, which is heated by stepping furnace and dephosphorized by high pressure water after entering roughing mill. The roughing mill material is cut head, tail and then entered into finishing mill to implement computer controlled rolling. After final rolling, it passes through laminar cooling (computer controlled cooling rate) and coiling machine to become straight roll. The head and tail of straight hair roll are often tongue and fish tail, the thickness and width accuracy is poor, and the edge often has wave shape, hem, tower shape and other defects. After finishing the straight hair coil by cutting the head, cutting the tail, cutting the edge, straightening and leveling several times, then cutting the plate or rewinding, it becomes: hot rolled steel plate, flat hot rolled steel coil, slitting strip and other products. The hot rolled pickling plate roll is formed after removing the oxide skin by pickling and applying oil.
CHAENG has rich experience in manufacturing large steel casting parts for rolling mill, such as rolling mill stand, bearing block, wokroll chock, cylinder block, rolling mill pedestal, and so on, among which rolling mill stand is the key part of the rolling mill working base. CHAENG can manufacture rolling mill stand with high sufficient strength and stiffness according to customers' drawings and requirements. Weight: 1-150T Material: ZG270-500 Application: Metallurgical industry Customizable: Yes, based on user's drawings
Choose Piyali Engineering Corporation, your trusted manufacturer and supplier of Rolling Mill Equipment including, Mill Roll Stands, Roll Chocks, Roll Bearings, Rolling Mill gear Universal couplings, Gearbox parts, Chain sprockets & Plummer blocks and more. Our excellence ensures seamless Rolling Mill operations.Our commitment to excellence guarantees seamless operations for industries with reliable equipment and top-notch services. At Piyali Engineering Corporation, we prioritize quality and strive to deliver products that meet and exceed customer expectations. Our adept and seasoned team is deeply committed to providing unparalleled service and ensuring utmost customer satisfaction. For any inquiries or further information, please do not hesitate to get in touch with us via the provided contact details: PIYALI ENGINEERING CORPORATION
We are pleased to introduce Piyali Engineering Corporation, located in Delhi, India. We are leading manufacturer and supplier specializing in the production of Sponge Plant DRI (Direct Reduced Iron) equipment and vital components for steel plants, alongside catering to a diverse range of industries including sugar mills, cement plants, fertilizer plants, chemical plants, coal washeries, activated carbon plants, and ball mills. With a strong focus on quality and innovation, Piyali Engineering Corporation stands as a trusted provider of cutting-edge solutions across various industrial sectors. With a wide range of offerings and a strong customer base, we have been serving the industry for several years. Our product range includes various capacities of DRI kilns and coolers, ranging from 50TPD to 600TPD & 900TPD, along with components such as support rollers, pinions, shafts, shells, combined bearing housing complete assemblies, spring plates, Ball Mill Pinion Shaft, Mill Head End Cover for Ball Mill Manufacturer, girth gears, and more. These offerings are designed to meet the needs of Cement Plants, Power Plants, Steel Plants, Sponge Iron Plants, Chemical Plants, Fertilizer Plants, and various other industries. Explore top-notch Lime Kiln Paper Mill Equipment at Piyali Engineering Corporation for customized, cost-effective solutions. Our commitment to excellence ensures reliable expertise and high-quality equipment, guaranteeing seamless Paper Mill operations. Specializing in Rotary Pulp Dryers, we provide comprehensive solutions for your paper manufacturing needs. Choose Piyali Engineering Corporation, your trusted manufacturer and supplier of Rolling Mill Equipment including, Mill Roll Stands, Roll Chocks, Roll Bearings, Rolling Mill gear Universal couplings, Gearbox parts, Chain sprockets & Plummer blocks and more. Our excellence ensures seamless Rolling Mill operations. Our commitment to excellence guarantees seamless operations for industries with reliable equipment and top-notch services. At Piyali Engineering Corporation, we prioritize quality and strive to deliver products that meet and exceed customer expectations. Our adept and seasoned team is deeply committed to providing unparalleled service and ensuring utmost customer satisfaction.
We are pleased to introduce Piyali Engineering Corporation, located in Delhi, India. We are leading manufacturer and supplier specializing in the production of Sponge Plant DRI (Direct Reduced Iron) equipment and vital components for steel plants, alongside catering to a diverse range of industries including sugar mills, cement plants, fertilizer plants, chemical plants, coal washeries, activated carbon plants, and ball mills. With a strong focus on quality and innovation, Piyali Engineering Corporation stands as a trusted provider of cutting-edge solutions across various industrial sectors. With a wide range of offerings and a strong customer base, we have been serving the industry for several years. Our product range includes various capacities of DRI kilns and coolers, ranging from 50TPD to 600TPD & 900TPD, along with components such as support rollers, pinions, shafts, shells, combined bearing housing complete assemblies, spring plates, Ball Mill Pinion Shaft, Mill Head End Cover for Ball Mill Manufacturer, girth gears, and more. These offerings are designed to meet the needs of Cement Plants, Power Plants, Steel Plants, Sponge Iron Plants, Chemical Plants, Fertilizer Plants, and various other industries. Explore top-notch Lime Kiln Paper Mill Equipment at Piyali Engineering Corporation for customized, cost-effective solutions. Our commitment to excellence ensures reliable expertise and high-quality equipment, guaranteeing seamless Paper Mill operations. Specializing in Rotary Pulp Dryers, we provide comprehensive solutions for your paper manufacturing needs. Choose Piyali Engineering Corporation, your trusted manufacturer and supplier of Rolling Mill Equipment including, Mill Roll Stands, Roll Chocks, Roll Bearings, Rolling Mill gear Universal couplings, Gearbox parts, Chain sprockets & Plummer blocks and more. Our excellence ensures seamless Rolling Mill operations.Our commitment to excellence guarantees seamless operations for industries with reliable equipment and top-notch services. At Piyali Engineering Corporation, we prioritize quality and strive to deliver products that meet and exceed customer expectations. Our adept and seasoned team is deeply committed to providing unparalleled service and ensuring utmost customer satisfaction.
We are pleased to introduce Piyali Engineering Corporation, located in Delhi, India. We are leading manufacturer and supplier specializing in the production of Sponge Plant DRI (Direct Reduced Iron) equipment and vital components for steel plants, alongside catering to a diverse range of industries including sugar mills, cement plants, fertilizer plants, chemical plants, coal washeries, activated carbon plants, and ball mills. With a strong focus on quality and innovation, Piyali Engineering Corporation stands as a trusted provider of cutting-edge solutions across various industrial sectors. With a wide range of offerings and a strong customer base, we have been serving the industry for several years. Our product range includes various capacities of DRI kilns and coolers, ranging from 50TPD to 600TPD & 900TPD, along with components such as support rollers, pinions, shafts, shells, combined bearing housing complete assemblies, spring plates, Ball Mill Pinion Shaft, Mill Head End Cover for Ball Mill Manufacturer, girth gears, and more. These offerings are designed to meet the needs of Cement Plants, Power Plants, Steel Plants, Sponge Iron Plants, Chemical Plants, Fertilizer Plants, and various other industries. Explore top-notch Lime Kiln Paper Mill Equipment at Piyali Engineering Corporation for customized, cost-effective solutions. Our commitment to excellence ensures reliable expertise and high-quality equipment, guaranteeing seamless Paper Mill operations. Specializing in Rotary Pulp Dryers, we provide comprehensive solutions for your paper manufacturing needs. Choose Piyali Engineering Corporation, your trusted manufacturer and supplier of Rolling Mill Equipment including, Mill Roll Stands, Roll Chocks, Roll Bearings, Rolling Mill gear Universal couplings, Gearbox parts, Chain sprockets & Plummer blocks and more. Our excellence ensures seamless Rolling Mill operations.Our commitment to excellence guarantees seamless operations for industries with reliable equipment and top-notch services. At Piyali Engineering Corporation, we prioritize quality and strive to deliver products that meet and exceed customer expectations. Our adept and seasoned team is deeply committed to providing unparalleled service and ensuring utmost customer satisfaction.
Triple Roll Mill H.S. CODE : 84798200
About Steel re-Rolling Mill Steel Re-rolling is a major steel section and bar producing technology used in India and abroad. Since its inception in India with setting up of first re-rolling mill in Kanpur in 1928, this technology has contributed significant steelmaking capacity in secondary steel sector in India. Air Pollution Depending upon the fuel used in heating the furnace of a Steel Re-rolling Mill, the characteristics of flue gases may vary. For coal fired furnaces they may consist of gaseous as well as particulate pollutants. For oil or gas fired furnaces, these flue gases may consist of just gaseous pollutants. The flue gases may also be corrosive in nature. Selection of Technology for Air Pollution Control Device Selection of Technology for Equipment in an Air Pollution Control System in case of a Steel Re-rolling Mill depends upon the fuel to be used : a. Scrubber based System for Oil / Gas Fired Furnaces b. Cyclone and Scrubber based System for Coal Fired Furnaces About Scrubber based System for Oil / Gas Fired Furnaces Characteristics of Air Pollution Generated In Induction Furnace 1 Pollutants : Dust & Gases such as NO , SO , CO, Co x 2 2 2 Concentration : SPM - 1200-1500 mg/Nm (Maximum, in coal fired) 3 So - 800-1000 mg/Nm 2 4 NO - 20-50 mg/Nm x 5 Temperature : At Suction Point: 250-300 C 6 Nature of Dust : Slightly Sticky, Non Abrasive and Non Explosive Control Practices The control practice adopted in controlling air pollution in this industry mainly depends upon following parameters : 1 Dust/Gas Concentration at inlet 2 Discharge Standards 3 Temperature of Flue Gases 4 Nature of Pollutant i.e. Dust (Particulate) or Gaseous 5 Nature of Dust i.e. Sticky, Abrasive 6 Nature of Gases i.e. Corrosive, Non Corrosive Working of Equipment 1. Ducts & Bends : 2. Scrubber : 3. ID Fan : 4. Stack (Chimney) : About Cyclone and Scrubber based System for Coal Fired Furnace Working of Equipment 1. Ducts & Bends : 2. Cyclone : 3. Scrubber : 4. ID Fan : 5. Stack (Chimney) : Discharge Characteristics as Per Norms 1 Dust : Less than 150 mg/ Nm 2 Temp : Less than 80-100 C 3 Gases : Traces of SO , NO , Co , Co.
It can be used to roll carbon steel,alloy steel, stainless steel, non-ferrous metal, rare metal and precision alloy in cold condition. Its products have been widely used in such industries as metallurgy, automotive industry, bearing manufacturing, oil machinery manufacturing and so on. Product series as LG30, LG60,LG80, LG120, LD8-15,LD15-30,LD15-60,LD120 etc. High quanlity: Certified with ISO9001:2000 Quality System Brand name: Our brand is Changxin, if you need us to put your own logo on product. It is ok Packing Size: According to products size and quantity Packing method: Wooden case or as per customers requirements Delivery time: 45 days after received deposit Minimum order: As per clients requirements OEM: YES, we can manufacture the parts according to customers drawings
Spare Parts for Hot Rolling Mill: 1. spare parts for Hot rolling mills 2. Material available: stainless steel,alloy steel,carbon steel,etc. 3. Good surface,Tight tolerance,Fast delivery 4. Standard:GB,AISI, BS,DIN,ASTM 5. Weight:0.02kg-100kg 6. Production capacity: more than 30 tons per month 7. Precision steel casting production process: Mould making-Shell making-Pouring-Sand (glass ball)blasting-CNC machining-Inspection-Assembly. 8. Surface treatment: polishing, plating, shot blasting, sand blasting. 9. Delivery time: within 30 days 10. Terms:FOB,CIF 11. Precision steel casting OEM service can be supplied, high precision CNC machining and assembly are also available. 12. Annual output: 3,600T 13. Customized OEM parts specifications are available (drawings or samples) High quanlity: Certified with ISO9001:2000 Quality System Brand name: Our brand is Changxin, if you need us to put your own logo on product. It is ok Packing Size: According to products size and quantity Packing method: Wooden case or as per customers requirements Delivery time: 45 days after received deposit Minimum order: As per clients requirements OEM: YES, we can manufacture the parts according to customers drawings.
XH-401 two roll mill is mainly used to uniformly mix the raw material and additinal agents for testing and apply the experiment resoults and its ratio in the production line to satisfy the requirement of quality and color specified by the customer. • Built-in heater,together with LCD temperature controller and high-precision sensor,can automatically compensate the temperature to guarantee the temperature equalization. • Telfon stop block. • Taiwang gear motor,together with high-precision gearing chain,guarantees stable operation,low noise and good durability. • Emergent reverse guarantees the safety. • Alternative configuration:oil heating and cooling system,AC frequency control system,independent limitless speed change,automatic roller-gap adjustment ande man-machine interface. • Relyng on the principle of customer-based, the company can customize the product according to the customer's requirements. 450KG 1000*550*1200.
During the last years the most used rolling stands type for long products production have been the housingless stands and, even not less much, the cantilever stands. The more frequent requests of our customer, involved in lower investments for complete rolling mills or for revamping of existing plants, are: To reduce the investments for civil works, buildings and cranes. To reduce the equipment delivery times. To reduce the investment cost of mill train. To reduce spare parts. Equipment without on board plant Easy maintenance equipment High performance equipment In other words the rolling mill is primarily interested in lower costs and as well as higher yields! In order to grant these requests and the suggestions of the production and maintenance mangers, PERT has been the first supplier now to develop a new generation of stands called BS Type rolling stands, the Intermediate block and 2XTechnology Finishing Block (the only block in the market that can work with 2 strand).
Aluminum continuous caster rolling mill.
Quick Details Place of Origin: Jiangsu, China Brand Name: Mivi Type: Cold Rolling Mill Condition: New Video outgoing-inspection: Provided Machinery Test Report: Provided Marketing Type: Ordinary Product Warranty of core components: 6 months Core Components: Pressure vessel Voltage: 220v Power: standard Dimension(L*W*H): As customer's requirement Certification: ISO Warranty: 6 months After-sales Service Provided: Free spare parts, Field installation, commissioning and training, Field maintenance and repair service, Video technical support, Online support Key Selling Points: High Productivity Showroom Location: None Applicable Industries: Building Material Shops, Manufacturing Plant, Construction works After Warranty Service: Online support Local Service Location: None Product name: cold rolling mill Raw material: corbon/stainless steel entry thickness: 5mm entry width: 1750mm minimum output thickness: 0.05mm maximum rolling speed: carbon steel can up to 1200mpm and stainlessteel canreach 600mp Packaging & Delivery Port shanghai or ningbo Lead Time: Quantity(Sets) 1 - 1 >1 Est. Time(days) 50 To be negotiated Products Description cold rolling mill Function of cold rolling mill: To achieve the desired thinner stee coils by multiple cold rolig passes with the help of hydrauli AGC screwdown and big reel tension The maximum input thickness can up to 5mm and the width can up to 1750mm. The minimum output thickness can lower to 0.05mm The maximum rolling speed for carbon steel can up to 1200mpm and for stainlessteel canreach 600mp Product name cold rolling mill Raw material corbon/stainless steel entry thickness 5mm entry width 1750mm minimum output thickness 0.05mm maximum rolling speed carbon steel can up to 1200mpm and stainless steel canreach 600mp
ROLLING MILL PLANT SPARE PARTS
Four Row Cylindrical Roller Bearing Rolling Mill Bearing FCD6492240/804571/BC4B 322216/VJ202 Inner Ring: 320.000mm Outer Ring: 460.000mm Width: 240.000mm Chamfer: 3mm Outer diameter of Inner Ring:364.00mm Basic Dynamic Load Rating: 3370KN Basic Static Load Rating: 7550KN Gross Weight: 141kg Material: Carburizing Steel Four row cylindrical roller bearings as rolling mill bearings are mainly used on rolling mill stands, calenders and roller presses. The four rows of rollers lends itself to carry large radial loads, but no thrust capacity, for the given bearing cross section. Four row cylindrical roller bearings are separable, the rings and rolling elements could be separated, it is convenient to wash, check, mount and dismount. Four-row cylindrical roller bearing can only bear radial load; therefore, they must be installed with groove ball bearings or angular contact ball bearings, it will be the latter which bear the axial load. our row cylindrical roller bearings are classified into FC, FCD, FCDP types. Type FC four row cylindrical roller bearing consists of two outer rings and one inner ring, which have two ribs on outer rings, a center rib in the middle, and the inner ring without rib. Essentially, type FCD four row cylindrical roller bearing is formed by two type NN type of double row cylindrical roller bearings, so it has double outer rings, double inner rings, and the inner ring without rib. Type FCDP four row cylindrical roller bearing consists of two outer rings and two inner rings, which have two ribs on outer rings. Type FC, FCD and FCDP four row cylindrical roller bearings permit axial displacement in double directions of the housing relative to the shaft. Therefore, they are suitable to be used as non-locating bearings. Normally, their cages are made from solid machinery. I.D Size range: above 150mm FC3045120: 150mm*225mm*120mm FC3045120: 150mm*225mm*120mm FC3248168: 160mm*240mm*168mm FC3652168: 180mm*260mm*168mm FC3656180: 180mm*280mm*180mm FC3852168E: 190mm*260mm*168mm FC4058192: 200mm*290mm*192mm FC4462192: 220mm*310mm*192mm FC4666206: 230mm*330mm*236mm FC4668260: 230mm*340mm*260mm FC4866220: 240mm*330mm*220mm FC4872220: 240mm*360mm*220mm FC5275500YA3B2: 260mm*360mm*200mm FC5274220: 260mm*370mm*220mm FC5276280: 260mm*380mm*280mm FC5476230: 270mm*380mm*230mm FC5678220: 280mm*390mm*220mm FCDP5678275: 280mm*390mm*275mm FC5882240: 290mm*410mm*240mm FC6084240: 300mm*420mm*240mm FCD6084300: 300mm*420mm*300mm FCD6084300A: 300mm*420mm*300mm FC6896280: 340mm*480mm*280mm FCDP96130450: 480mm*650mm*450mm FCD96136500: 480mm*680mm*500mm
Our company has available for sale a stock of 4.500 mt of steel and cast iron used rolling mills rolls . Origin Romania Different dimensions, weights and chemistry. Pictures, list and details on request.
Small Horizontal steel rolling mill is mainly used in steel mills to produce steel bars, shaped steel, wire rod, channel, flat steel, steel plates and other products. The raw material is generally scrap or billet (40-100mm), and the production capacity is suitable for 0.5-5t/h rebar production line, and the diameter of the final product: 8-32mm.
