XGQ-30F/50F/100F/130F/150F Soft Mounted Automatic Washer Extractor *Full suspension structure,which effectively isolate the vibration during washing; *This machine is a fully enclosed rear drainage frame structure with no pollution; *Basket and extermal plates are made of high grade stainless steel material for durability and anti-corrosion. Technical Parameter Totally 5 models out of 15 machines size from minimum 15kg dry load capacity to the maximum 150kg. Model Unit XGQ-30F XGQ-50F XGQ-70F XGQ-100F XGQ-120F Capacity kg 30 50 70 100 120 Basket size mm �¦905*500 �¦1065*628 �¦1200*600 �¦1230*800 �¦1300*900 Washing speed rpm 40 38 38 38 38 Extracting speed rpm 750 720 700 650 630 Motor power kw 4 5.5 7.5 7.5 11 Inverter power kw 5.5 7.5 11 11 15 Steam ratio kg/kg 0.7 0.7 0.7 0.7 0.7 Water pipe Inch 1.5 1.5 2 2 2 Steam pipe Inch 1 1 1 1 1 Soap pipe Inch 3/4 3/4 3/4 3/4 3/4 Steam pressure Mpa 0.4-0.6 0.4-0.6 0.4-0.6 0.4-0.6 0.4-0.6 Water pressure Mpa 0.2-0.3 0.2-0.3 0.2-0.3 0.2-0.3 0.2-0.3 Dimension cm 140*138*176 160*160*210 175*154*214 180*195*230 180*195*230 Weight kg 1450 2200 2800 3200 4300 Note:The above specifications are subject to change without notice. Both steam heating and electric heating are available for custumers' choice.
Bolts, nuts, hand-dryer, cashmere.
Electronic goods.
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size �¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
