NSQ submersible sludge pump is hydraulic machinery, the motor and the pump of which are coaxially submerged in medium to work. The overflowing parts of the pump are made from high alloy wear-resistant material, so the pump has good wear resistance and large flowing passage. It is applicable for conveying media such as sludge, ore slurry, coal slurry, sandstones containing big solid particles. The product is designed and manufactured by domestic and oversea advanced technologies. Besides the main impeller, the bottom of the pump is additionally provided with a set of agitation impeller which can spray the deposited sludge into turbulent flow, and therefore the pump realizes high-concentration conveying under the condition of no auxiliary device. The unique seal device can effectively balance the pressure inside and outside the oil chamber, so as to protect the reliability of the mechanical seal to the maximum extent. The motor adopts various protective measures such as overheat protection, water inle t detecting protection, and can operate safely for a long term in harsh working conditions. The pump is applicable for pumping sand for building, silty sand, silt, tailing slurry, ore, iron sand ore, sediment in sewage treatment works, etc. Structural Property 1.The whole machine is dry submersible pump, and the motor adopts oil chamber seal mode and is provided with mechanical seal inside, so that high pressure water and impurities are effectively prevented from entering inner cavity of the motor. 2.Besides the main impeller, there is the agitation impeller which can agitate the sludge deposited on the water bottom into turbulent flow and pump the sludge out. 3.The trans-flux parts such as the impeller and the agitation impeller are made from high-hardness high chromium cast steel, have wear resistance, corrosion resistance and strong drainage capacity, and allow big solid particles to pass. 4.The motor is submerged in water, is not limited by suction stroke, and has high sludge suction rate and thorough desilting. 5.The integral device is simplified, needs no auxiliary stirrer device or ejector device, and has simple and convenient operation and low total investment of the unit. 6.The agitation impeller directly approaches the depositional surface, and controls the concentration through submerged depth. Under the condition of large medium proportion, an auxiliary device can be arranged to increase the concentration of the medium. Use Conditions 1 The power source is 50Hz/380V three-phase alternating-current supply, and the capacity of the substation transformator is two to three times of the rated capacity of the motor. 2 The temperature of the medium cannot exceed 60íµ, and the medium does not contain inflammable or explosive gases. 3 The maximum weight concentration of the solid particles in the medium: the maximum weight concentration of the ash is 45% and the maximum weight concentration of the slag is 60%. 4 The submerged depth of the unit is not more than 20 meters, and the minimum submerged depth takes submerging of the motor as reference. 5 The unit works in the medium vertically, and the working status is continuous. Weight is 210KG.
Specification: slurry concentration: ín 70%, capacity: 30-1000m3/h , Slurry granularity: :10mm , head to: 60-1000m Pump resistance efficiency: 0.7-0.85 Application area: A) long distance, high-lift transportation for the trailing of black metal, color metal, gold, minerals . B) long distance, high-lift transportation for gray water, bauxite, red mud, cws from power plants, aluminum, coal, chemical industry C) long distance, high-lift transportation for D) sewage sludge treatment plant for the long-distance, high-lift transport E) desilting for rivers and lakes 10ton
FEATURES LOWER SP10116L-G01 Spare Parts is installed on 100RV-SP Vertical slurry pump. 100RV-SP Vertical Slurry Pump is designed for handling abrasive and corrosive liquids and slurries, while submerged in sumps or pits. Suited for applications requiring greater reliability and durability than conventional vertical process pumps can offer. It is mainly used for pumping the slurries with high abrasive, strong corrosion and high concentration liquids contain suspended solid particles. Design Features: Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. The SPR model is elastomer covered. Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Upper Strainer - Drop-in metal mesh, snap-on elastomer or polyurethane for SP and SPR pumps. Strainers fit in column openings. Lower Strainer - Bolted metal or polyurethane for SP, moulded snap-on elastomer for SPR. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Submerged Bearings - None Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries. Design Features Bearing assembly - a large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame. Volute Liners - easily replaceable liners are bolted, not glued, to the casing for positive attachment and east of maintenance. Hard metal liners are completely interchangeable with pressure moulded elastomer. Elastomer seal rings back all liner joints. Pump casing - Casing halves of cast or ductile iron with external reinforcing ribs provide high operating pressure capabilities and an extra measure of safety. Impeller front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Hard metal and moulded elastomer impellers are completely interchangeable.
Metslurry is a professional company supplying slurry pumps and spares, and also focus on making a world-level supply chain to the mining world, we provide interchangeable pumps, the quality is the same as warman. The models are ah(r), sp(r), l(r), m(r), g series and so on. We have very professional team to select the correct slurry pumps and give after-sales services. Our goal is to be your spare parts warehouse and workshop. We already have built 3 warehouses and workshops in china, australia and laos, so most common parts are in stock in above area, it is fully guaranteed for delivery time if you have any enquiry or urgent need.
Feature of the product: use of double casing , it has the character of high efficiency , wear-resistant, Stable performance and ecxellent changeable parts , the material of liner and impeller is adopt of wear-resistant metal or rubber , the discharge port can be positioned ar 8 differernt positions at an intervals of 45°. The pumps may be installed in multistage series , may be driven by belt or direct Connection, the seal of shaft may be adoptable of gland seal , expeller seal or mechanical seal, the direction of rotation from the drive end is clickwise Application: the pumps are suitable for deliverling abrasive , high density slurries in the metallurgical , mining, coal and power industrial departments , for example raw ore , middings , concentrates , gangues etc.
ZJ slurry pump is a new generation anti-wear, energy saving slurry pump.The ZJ series pumps used international advanced solid-liquid two-phase flow theory and were designed using the minimum-wear principle.The flow parts of these pumps are suitable for the flow of state media for it's set shape, which reduces hydraulic loss of eddy and impact, both in pump and along the pipelines; so reduced friction of flow parts, lower noise and vibration of the pump translates into improved hydraulic efficiency. Product name: ZJ slurry pump Item:advanced slurry pump than AH slurry pump Features: ---Cetnrifugal cantiliver type, easily repair bearing house ---Can transport high density slurry containing highly hard abrasive particles like concrete, coal cinder, cement, clay, grit ,juice etc ---The slurry density can be up to 60% Data sheet : ---Capacity: up to 19*20m3/h ---Head:up to 94m ---Material: High chrome alloy and rubber lined Function Introduction: ---Mining, metallurgy, coals, electricity, construction material industry etc
ZGB(ZJ) SERIES SLURRY PUMP Tailing Slurry Pump1.2 Coal Ash Slurry Pump To meet the power plant, metallurgical and coal industry development needs for the ash and slag and slurry transport characteristics of working conditions, with many years of experience in designing and manufacturing slurry pumps. Hebei Jishiyu Pump Co.,Ltd. designed and developed our latest generation of high flow, high head, can be multi-stage series of ZGB (ZJ) series slurry pump. The TAILING SLURRY PUMP main technical features are as follows: 1. The use of modern CAD design, hydraulic performance, high efficiency and low wear rate; 2. Spacious flow, anti-clogging performance, cavitation performance; 3. The use of pay plus filler combined impeller and mechanical seal seal to ensure no leakage of slurry; 4. Reliability design, ensure the machine mean time between failures (MTBF) increased significantly; 5. Metric bearings lubricated with thin oil, a reasonable set of lubrication and cooling system to ensure that the bearing operating at low temperatures; 6. Wet parts using special materials, wear and corrosion resistant; specially treated for water and salt water ash and electrochemical corrosion conditions; 7. Allows the pressure in the range, you can use multi-level series, the maximum allowable working pressure of 3.6Mpa. The series pump for Coal mine product has reasonable structure, high efficiency, reliable operation and easy maintenance, etc., widely used in electric power, metallurgy, mining, coal, building materials, chemical industry conveying abrasive or corrosive slurries, particularly in electricity plant ash. The main product slurry pump is of 20 series, 80 varieties and more than 400 specifications, such as slurry pump, tailing slurry pump, sand gravel pump and dredge pump all can we product. For more information on pumps, please click here.
LL(M) SERIES SLURRY PUMP Medium Duty Slurry Pump1.5 horizontal slurry pumps Type LL(M) pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for handling medium abrasive, medium density slurries in the metallurgical, mining, coal, power plant, building material and other industrial departments. The pumps of this type also can be installed in multistage series. The series of the pumps are of double casing.The liners are made from high chrome alloy as well as rubber and elastomer. The shaft seals forms of the series of the pumps can be adoptable of gland seal,centrifugal seal and mechanical seal.The discharge pipes can be positioned at intervals of 45 degree by request and oriented to any eight position to suit installation and applications. The capacity of the LIGHT & MEDIUM DUTY SLURRY PUMP can reach 3600m3/h, the head of the pump can reach 70 m. The discharge pipe can reach 16 inches. The main product slurry pump is of 20 series, 80 varieties and more than 400 specifications, such as slurry pump, tailing slurry pump, sand gravel pump and dredge pump all can we product. For more information on pumps, please click here.
Description Horizontal slurry pump range offer to use in mining, chemical, and industrial applications widely. The pump is designed for heavy duty applications such as mill discharge, process plant, and tailings, high pressure pipelines, as well as other specialty applications. The pump provides excellent wear life while maintaining high efficiency during its wear cycle. It helps the new building plant to start production and recover their cost in a short time with the minimum investment. Not only our own brand slurry pumps but also it could be interchangeable with other brands on spares and whole pumps. We have stock on some regular spares. It saves the users' cost on stock and increases their supply chain's efficiency. Key Features Bearing assembly - The large diameter shaft with famous brand bearings contributes to long working life. Liners-Easy to replace and maintain. Hard metal liners are completely interchangeable with rubber or PU. Casing-Cast iron or ductile iron casing provide high operating pressure capabilities and extra protection on the safety. Impeller-Hard metal and moulded elastomer impellers are completely interchangeable with each other. High efficiency and high head designs are also available. And the arge particle is easy to pass through. FAQ: 1. Are your pump and spares interchangeable with other brands? Yes. 100% interchangeable, whatever the material, working life and working efficiency. 2. What price of your pump and spares? Our price is 30~50% of the original but the same working life. 3. What is your lead time? Some popular spares are in stock which could deliver within 5 days after your PO. If without stock, we could deliver within 3 weeks. 4. What is your warranty? One year for the whole pump except the wear parts. The working life of wet parts is the same as the most famous brand. 5. Do you have OEM service? Yes. We offer OEM service to our clients. And our engineers could train the users on site how to start, use and maintain the pumps.
Product Application Delivery of slurry with strong abrasion and high concentration for metallurgy, mines, coal and power plant, e.g. the pulp from the ore concentrate and tailing of nonferrous mines, with particle diameter greater than 0.1mm and Cv=5%. The shaft seal can adopt expeller type shaft sealing , gland packing assembly and mechanical sealing. Main Features AH series centrifugal slurry pump frame plates have replaceable wear-resistant metal liners ,impellers&volute liners are made of wear-resistant metal(such as A05,A49,and other high chrome metal). · AH series centrifugal slurry pump bearing assembly use cylindrical structure, adjusting the space between impeller& front liner easily, being removed completely when being repaired. Grease lubrication. · AH series centrifugal slurry pump shaft seal could use the packing seal, expeller seal and mechanical seal. One pump also can be use packing seal with expeller seal together. · The discharge outlet can be positioned at intervals of 45 degrees by request and oriented to any 8 positions to suit installations and applications. · AH series centrifugal slurry pump can be installed in multistage series to meet the delivery for long distance. · AH series centrifugal slurry pump drive types, such as direct coupling drive(DC), V belt drive(CR, CV, ZV), etc.
Spare Parts Name: Impeller Brand: Tech macro Original: China The pump impeller is made of rubber or metal,and the metal liner and rubber liner are interchangeable .The back vane can reduce the sealing pressure ,and it can also cut down backflow to the largest extent at the same time . On the other hand ,cast-in impeller threads are more suitable for slurry . Spare parts Name: Bearing assembly Brand: Techmacro The shaft sleeve possesses high hardness which makes it suitable for high abrasive slurry ,and O shaped seal rings are set at both ends to protect the shaft .Sliding fit is used between shaft and sleeve,and it facilitates both assembly and disassembly.On the other hand ,the shaft is designed with large diameter and shortcantilever,and this design can mini mize deflection as well as vibration .In addition ,the heavy duty roller bearing is installed inside the movable bearing cylinder . Spare parts Name: Cover plant liner Brand: Techmacro Original: China The cover plate is produced using elastomer or hard metal ,such as natural rubber,high -chromium alloy,etc. It has various sizes and styles ,and the installation is very easy .Additionally,OEM design is accepted. Spare parts Name: Cover plant liner Brand: Techmacro Original: China The cover plate is produced using elastomer or hard metal ,such as natural rubber,high -chromium alloy,etc. It has various sizes and styles ,and the installation is very easy .Additionally,OEM design is accepted. Package:Standard export plywood case Delivery date:30 days for pump available at factory by receipt of prepayment. Packaging Details:The normal package is wooden box(Size: L*W*H). If export to european countries,the wooden box will be fumigated.If container is too tigher,we will use pe film for packing or pack it according to customers special request.
Slurry pump Slurry pump is contain cantilever and horizontal centrifugal pumps, which apply to transport slurry with strong corrosion proof and high concentration for such industries as metallurgy, mine, coal, power, buliding etc.This kind of pump can be used in multi stages.Pump body consist of replaceable metal or rubber lining and its impeller is made of wear resistant metal or rubber.The shaft seal of pump may adopt packing seal centrifugal. Contact us company:shijiazhuang ruite pump co., ltd. -
Slurry pumps Range (discharge):1-18inch 2. Capacity: 10-5400 m3/h ¡¡3. Head: 5-125m ¡¡4. Impeller type: non-clog (open &close) 5. Shaft sealing: packing/gland packing & mechanical ¡¡6. Wet parts material: a05, a07, rubber, 3) slurry pump general features: 1. Xiyue brand xh/xhh slurry pumps are heavy duty pumps. They are cantilevered, horizontal, Centrifugal slurry pumps. Especially they are designed for most difficult pumping applications. 2. Xiyue xhh models are designed for heavy duty applications require high head per stage at high pressures. It is suitable for long distance transporting or where others require more than one pump in series. ¡¡3. Xiyue xh models display total interchangeability between hard metal and ¡¡¡¡elastomeric liner pumps. 4. They are mainly used in: power plant, chemical process, coal, heavy minerals, paper and pulp, mill discharge, lime grinding, bottom boiler fly, ash cyclone feed, slag granulation, suction hopper dredging, barge loading, sand reclamation ect. ¡¡¡¡¡¡ 4) slurry pump structure features: 1. Xiyue xh/xhh pumps are single stage, single suction, and overhang shaft, centrifugal, ¡¡¡¡double-casing horizontal type. Wet parts are made of abrasive resistant hard metal or rubber. ¡¡2. Bearing assembly use cylindrical structure, adjusting the space between impeller and ¡¡¡¡front liner easily, being removed completely when being repaired. ¡¡3. Bearing assembly uses grease lubrication. ¡¡4. The shaft seal could use the packing seal, expeller seal and mechanical seal. ¡¡5. The discharge branch can be positioned at intervals of 45 degrees by request and oriented ¡¡¡¡to any eight positions to suit installations and applications. ¡¡¡¡ Material construction Pump body: cast iron/grey iron Wooden box
Product nameTgm-3e slurry pump TypeTgm Pump size4/3 Capacity126-252m3/h Head12-97m Allowable max. Power120kw Speed600-1400r/min Npsh2-5m Introduction£º Model explanation Tgm-4f T: our company logo G: high head M: metal lined 4: discharge size (inch) F: frame type with maximum power Introduction of centrifugal slurry pump ¡ª¡ª tgm series Tgm series slurry pumps are cantilevered, horizontal slurry pumps, centrifugal slurry pumps. They are designed for the handling of highly abrasive, high-density slurries. This series pump may also be installed in multistage series The features of this kind of centrifugal slurry pump The frame plate liner and impeller for tgm series centrifugal slurry pump are made of wear-resistant metal. The shaft seals for the tgm series may choose gland seal or expeller seal. The discharge branch can be oriented to any of the eight positions to suit installations and applications. Application: They are designed for the handling of highly abrasive, high density slurries in the metallurgical, mining, coal, power generation, construction material and other industry. The pumps of this type may also be installed in multistage series. Tgm series slurry pump performance chart Pump modelAllowable max. Power(kw)Clear water performance¡¡ Capacity qHead h(m)Speed n(r/min)Max.Eff. ¦ç%Npsh (m)Impeller dia(mm) M3/hL/s Tgm-1c3016.2-34.24.5-9.525-921400-2200202-5.5330 Tgm-2d6068.4-13719-3825-87850-1400473-7.5457 Tgm-3e120126-25235-7012-97600-1400502-5508 Tgm-4f260324-72090-20030-118600-1000643-8711 Tgm-6s560468-1008130-28020-94500-1000654-12711 Note: quantity range recommended:50%q¡¯¡üq¡ü100%q¡¯(q¡¯appropriate to capacity at highest efficiency point). 2.Npsh:appropriate to point q recommended at highest speed. Exported wooden crate
Designed to be interchangeable with a Warman AH 6/4 Slurry Pump. FH Series slurry pumps are mainly using for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. Structure: The frame plates of this kind of slurry pump have replaceable wear-resistant metal liners. The impellers are made of wear-resistant metal. Bearing assembly of this kind of slurry pump use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication. The shaft seal of this kind of slurry pump could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications. Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. The pump of this type may be installed in multistage series to meet the delivery for long distance. Application: This kind of slurry pump mainly applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc. We supply complete, ready-to-use packages including pump, motor and frame desinged to your specifications. These pumps are ideal for the chemical transfer pump in plants for chemicals including lime. Standard export wooden cargo.
Specification : •Size range (discharge) 1” to 18” 25 mm to 450 mm •Capacities to 22,000 gpm to 5,000 m3/hr •Heads to 240 ft to 73 m •Pressures to 300 psi to 2,020 kPa. Size: 1"-16" Weight: 77-18864 Dimension:1cube-12cube.
Slurry pump is a kind of centrifugal pump, which usually means that under the action of centrifugal force, the liquid is thrown from the center of impeller to the outer edge and obtains energy, leaving the outer edge of impeller at high speed and entering the volute pump shell. In the volute pump case, the liquid slows down due to the gradual expansion of the flow channel, and then transforms part of the kinetic energy into static pressure energy, which flows into the discharge pipe at a higher pressure and is sent to the required place.
Slurry pumps are primarily made use of in dredging, mining, metallurgy, metropolitan, electric power, coal, thermal power flue gas desulfurization, petroleum, chemical, and also structure products sectors to transfer slurry consisting of abrasive solid particles. Such as beneficiation in a mine The transportation of medium slurry, the hydraulic ash removal of thermal nuclear power plant, the coal slurry and also hefty tool transport of coal cleaning plants, as well as the transportation of some corrosive slurry having crystals in the chemical industry. On top of that, in the field of seawater sand selection, the application fields of slurry pumps wholesale have likewise raised. Yet pick sand in the sea as well as dig sand in the river. Slurry pumps are called gravel pumps and also dredging pumps. Although they are called in different ways, they can all be called China slurry pumps in terms of architectural attributes and pump performance characteristics. Slurry pumps are commonly made use of in different sectors.
The current Horizontal Slurry Pump China is commonly utilized in mining, electrical power, metallurgy, environmental protection, petrochemical, new structure products and also various other markets to transport slurry including strong fragments The wholesale slurry pump has a vast efficiency array, good cavitation efficiency and also high effectiveness. Multi-stage tandem technology can be used to fulfill long-distance transportation. There are a range of steels available for overcurrent parts, as well as boost the deepness. Using numerous rates and also several versions allows the slurry pump for sale to run in a better industrial and mining setting. It has a long life span and also high operating effectiveness, and also can meet many kinds of harsh transportation problems.
