This machine is used to packing drinking straws in three sides sealing bag, printing function is available when using paper as packing material. Characteristics: 1.Having two colors printing device can be chosen 2.With automatic product counting function, product quantity may pre-set, once the pre-set value is reached. the machine will give an alarm. And the dam-brush will separate each set quantity packaged straw. 3.Printing, feeding, and packing can complete in one processing. 4.Packing straw length is adjustable within a certain range. Specification Drink Straw Diameter(mm) 5-12mm Need change some parts. Straw Length(mm) Standard: 190-210mm Extra mould: 170-260mm By change the sealing and cutting mold, printing cylinder Packing Model Paper type: wrap paper Sealing type: 3 side sealing 25-30mmï¼?Paper width: 25-30mm Production Speed With printingï¼?300pcs/min Without printingï¼?400pcs/min Printing Printing Colorï¼?Double Colour Printing type: flexographic 2.38mm; Thickness of plate (Including Two-sides Glue Paper): 2.28mm+double-sided adhesive 0.1mm(3M Brand)=2.38mm Paper Unwinding Frame 1SET Tension adjustï¼?Mechanical tension device, adjusted by manual Wrap paper roller core sizeï¼?3inchï¼?4.7inch Straw feeding hopper Material :Stainless steel frameï¼? Plexiglass: Adjustable to match straw length Straw down deviceï¼?induction and swing arm Feeding modelï¼?by chain feeding Printing Unit Single/Double Color Power transmission ï¼?By chain Between printing unit: By gear Traction unitï¼?1sets, rubber roller and chrome plated roller Printing unitï¼?Ink container, anilox roller, doctor blade, printing cylinder, rubber roller Dry unitï¼?1SET , by hot air, with temperature color registerï¼?By manual Sealing and Cutting Parts Lengthways sealingï¼?Sealing roller-on coupleï¼?pressure adjusted by manual Horizontalï¼?Sealing roller-on coupleï¼?pressure adjusted by manual, with cutting knife-one couple Materialï¼?mould steel Conveyor Belt 1setï¼? Synchronous reduction motor+ controller Counter dam-brush: one set, lifting by pneumatic cylinder Controller Counter and buzzersï¼?1setï¼?HUALI Brand Controlling inverter: 1.1KW Schneider Temperature controllerï¼?1setï¼?KEQIANG Brand Low-voltage electric parts: Schneider Total Power (Kw) 1.5 (220V) Over size (mm) 1900Ã?1000Ã?1600 (LÃ?WÃ?H) Weight (Kg) 400
This machine is used to packing drinking straws in three sides sealing bag, printing function is available when using paper as packing material. Characteristics: 1.Having two colors printing device can be chosen 2.With automatic product counting function, product quantity may pre-set, once the pre-set value is reached. the machine will give an alarm. And the dam-brush will separate each set quantity packaged straw. 3.Printing, feeding, and packing can complete in one processing. 4.Packing straw length is adjustable within a certain range. Specification Drink Straw Diameter(mm) 5-12mm Need change some parts. Straw Length(mm) Standard: 190-210mm Extra mould: 170-260mm By change the sealing and cutting mold, printing cylinder Packing Model Paper type: wrap paper Sealing type: 3 side sealing 25-30mmï¼?Paper width: 25-30mm Production Speed With printingï¼?300pcs/min Without printingï¼?400pcs/min Printing Printing Colorï¼?Double Colour Printing type: flexographic 2.38mm; Thickness of plate (Including Two-sides Glue Paper): 2.28mm+double-sided adhesive 0.1mm(3M Brand)=2.38mm Paper Unwinding Frame 1SET Tension adjustï¼?Mechanical tension device, adjusted by manual Wrap paper roller core sizeï¼?3inchï¼?4.7inch Straw feeding hopper Material :Stainless steel frameï¼? Plexiglass: Adjustable to match straw length Straw down deviceï¼?induction and swing arm Feeding modelï¼?by chain feeding Printing Unit Single/Double Color Power transmission ï¼?By chain Between printing unit: By gear Traction unitï¼?1sets, rubber roller and chrome plated roller Printing unitï¼?Ink container, anilox roller, doctor blade, printing cylinder, rubber roller Dry unitï¼?1SET , by hot air, with temperature color registerï¼?By manual Sealing and Cutting Parts Lengthways sealingï¼?Sealing roller-on coupleï¼?pressure adjusted by manual Horizontalï¼?Sealing roller-on coupleï¼?pressure adjusted by manual, with cutting knife-one couple Materialï¼?mould steel Conveyor Belt 1setï¼? Synchronous reduction motor+ controller Counter dam-brush: one set, lifting by pneumatic cylinder Controller Counter and buzzersï¼?1setï¼?HUALI Brand Controlling inverter: 1.1KW Schneider Temperature controllerï¼?1setï¼?KEQIANG Brand Low-voltage electric parts: Schneider Total Power (Kw) 1.5 (220V) Over size (mm) 1900Ã?1000Ã?1600 (LÃ?WÃ?H) Weight (Kg) 400
This machine is used to packing drinking straws in three sides sealing bag, printing function is available when using paper as packing material. Characteristics: 1.Having two colors printing device can be chosen 2.With automatic product counting function, product quantity may pre-set, once the pre-set value is reached. the machine will give an alarm. And the dam-brush will separate each set quantity packaged straw. 3.Printing, feeding, and packing can complete in one processing. 4.Packing straw length is adjustable within a certain range. Specification Drink Straw Diameter(mm) 5-12mm Need change some parts. Straw Length(mm) Standard: 190-210mm Extra mould: 170-260mm By change the sealing and cutting mold, printing cylinder Packing Model Paper type: wrap paper Sealing type: 3 side sealing 25-30mmï¼?Paper width: 25-30mm Production Speed With printingï¼?300pcs/min Without printingï¼?400pcs/min Printing Printing Colorï¼?Double Colour Printing type: flexographic 2.38mm; Thickness of plate (Including Two-sides Glue Paper): 2.28mm+double-sided adhesive 0.1mm(3M Brand)=2.38mm Paper Unwinding Frame 1SET Tension adjustï¼?Mechanical tension device, adjusted by manual Wrap paper roller core sizeï¼?3inchï¼?4.7inch Straw feeding hopper Material :Stainless steel frameï¼? Plexiglass: Adjustable to match straw length Straw down deviceï¼?induction and swing arm Feeding modelï¼?by chain feeding Printing Unit Single/Double Color Power transmission ï¼?By chain Between printing unit: By gear Traction unitï¼?1sets, rubber roller and chrome plated roller Printing unitï¼?Ink container, anilox roller, doctor blade, printing cylinder, rubber roller Dry unitï¼?1SET , by hot air, with temperature color registerï¼?By manual Sealing and Cutting Parts Lengthways sealingï¼?Sealing roller-on coupleï¼?pressure adjusted by manual Horizontalï¼?Sealing roller-on coupleï¼?pressure adjusted by manual, with cutting knife-one couple Materialï¼?mould steel Conveyor Belt 1setï¼? Synchronous reduction motor+ controller Counter dam-brush: one set, lifting by pneumatic cylinder Controller Counter and buzzersï¼?1setï¼?HUALI Brand Controlling inverter: 1.1KW Schneider Temperature controllerï¼?1setï¼?KEQIANG Brand Low-voltage electric parts: Schneider Total Power (Kw) 1.5 (220V) Over size (mm) 1900Ã?1000Ã?1600 (LÃ?WÃ?H) Weight (Kg) 400
This machine is used to packing drinking straws in three sides sealing bag, printing function is available when using paper as packing material. Characteristics: 1.Having two colors printing device can be chosen 2.With automatic product counting function, product quantity may pre-set, once the pre-set value is reached. the machine will give an alarm. And the dam-brush will separate each set quantity packaged straw. 3.Printing, feeding, and packing can complete in one processing. 4.Packing straw length is adjustable within a certain range. Specification Drink Straw Diameter(mm) 5-12mm Need change some parts. Straw Length(mm) Standard: 190-210mm Extra mould: 170-260mm By change the sealing and cutting mold, printing cylinder Packing Model Paper type: wrap paper Sealing type: 3 side sealing 25-30mmï¼?Paper width: 25-30mm Production Speed With printingï¼?300pcs/min Without printingï¼?400pcs/min Printing Printing Colorï¼?Double Colour Printing type: flexographic 2.38mm; Thickness of plate (Including Two-sides Glue Paper): 2.28mm+double-sided adhesive 0.1mm(3M Brand)=2.38mm Paper Unwinding Frame 1SET Tension adjustï¼?Mechanical tension device, adjusted by manual Wrap paper roller core sizeï¼?3inchï¼?4.7inch Straw feeding hopper Material :Stainless steel frameï¼? Plexiglass: Adjustable to match straw length Straw down deviceï¼?induction and swing arm Feeding modelï¼?by chain feeding Printing Unit Single/Double Color Power transmission ï¼?By chain Between printing unit: By gear Traction unitï¼?1sets, rubber roller and chrome plated roller Printing unitï¼?Ink container, anilox roller, doctor blade, printing cylinder, rubber roller Dry unitï¼?1SET , by hot air, with temperature color registerï¼?By manual Sealing and Cutting Parts Lengthways sealingï¼?Sealing roller-on coupleï¼?pressure adjusted by manual Horizontalï¼?Sealing roller-on coupleï¼?pressure adjusted by manual, with cutting knife-one couple Materialï¼?mould steel Conveyor Belt 1setï¼? Synchronous reduction motor+ controller Counter dam-brush: one set, lifting by pneumatic cylinder Controller Counter and buzzersï¼?1setï¼?HUALI Brand Controlling inverter: 1.1KW Schneider Temperature controllerï¼?1setï¼?KEQIANG Brand Low-voltage electric parts: Schneider Total Power (Kw) 1.5 (220V) Over size (mm) 1900Ã?1000Ã?1600 (LÃ?WÃ?H) Weight (Kg) 400
Rotary die-cutting machine with flexo printer Die-Cutting Machine Rotary die-cutting machine Model Max. paper sizes Area of valid printing Working speed Standard PrintingPlate Thickness Tinted precision(four color) Power of main motor Rollerdiameter HD3-B2000 1800*1250mm 1600*1250mm 0-60(pcs/min) 6mm ±1mm 4.0kw 408mm HD3-B2200 2000*1250mm 1800*1250mm 0-60(pcs/min) 6mm ±1mm 4.0kw 408mm HD3-B2400 2200*1250mm 2000*1250mm 0-60(pcs/min) 6mm ±1mm 4.0kw 408mm HD3-B2600 2400*1250mm 2200*1250mm 0-60(pcs/min) 6mm ±1mm 4.0kw 408mm HD3-C2000 1800*1470mm 1600*1470mm 0-60(pcs/min) 6mm ±1mm 4.0kw 480mm HD3-C2200 2000*1470mm 1800*1470mm 0-60(pcs/min) 6mm ±1mm 4.0kw 480mm HD3-C2400 2200*1470mm 2000*1470mm 0-60(pcs/min) 6mm ±1mm 5.5kw 480mm HD3-C2600 2400*1470mm 2200*1470mm 0-60(pcs/min) 6mm ±1mm 5.5kw 480mm Function and Characteristics� 1.lead edge feeding model , Gravure registering as convenient and correct with double baffle between the worktable. 2.CAD Module design can combination at will , one , two , multicolor printing unit. 3.Motorized detachment and combination, pneumatic locking and loosening of printing unit .Alarm ring and light to improved the operation security. 4.Pneumatic uplift plate device , the anilox roller will break away the plate automatic when the machine stop , which can not to breakage the plate surface. 5.Self-suck ink device can keep the plate surface humid when the motor stop , which can control the anilox roller racing circulate ink and cleaning the anilox roller automatic. 6.All the transmission axle and roller are made by the high-quality steel plated with rigid chrome and grinded surface. 7.All the gear was spray lubrication. 8.Numerical control electric phase device was used to every mostly roller , and it need to enter error number to adjustment at once , which can improve the working efficiency. 9.Automatic Counter Device can correct control the produce quantity. Hot sale various high quality Carton Cardboard Machine, Folder Gluer Machine, Lead Edge Feeder Printing Machine, Automatic Die-cutting Machine, Manual Die-cutting Machine, Gift Box from China leading manufacturer. Our Carton Cardboard Machine are high quality, cost effective and deliver more benefits. Welcome to choose us!
Power selection box accessories SJX5191TYL70 Chain 16A-4 API7F 88083 VALVE,QUICK,EXHAUST,.75NPT Ordinary nozzle JZS 4-18mm Electric control box FKQ6406Repair Kit QB21-82 Detroit Diesel PartsAir distribution system*air filter element 23182099 Drill pipe power tong accessories ZQ203 Gas valve plate support plate 100 0105-08MA 30172099 PIN, STOP TUBE M11-1015-010 Hydraulic tank accessories F-1000 Shear pin safety valve connector-AH33003.01 GT350E Universal* ReverseMirror assembly Winch drive shaft accessories ZJ32L6 inner spacer BA70001-06.10 Weichai diesel engine accessoriesEngine unit * Exhaust pipe gasket 4100 winch brake operating mechanismAccessories ZJ30 oil filter element FBX-400*30 WASHER NYLON 20MM 86871-20 156100113 LOCKNUT 32MM 78317-32 M11147 35Ã??70 BOP Accessories2FZ35-70 Ram rubber core 5" 35*70 BOP accessoriesFZ35-70 single ram blowout preventer repair kit Wheel hun I for Air Clutch LT965/305T AF700106-0306 Seal: Transmission Assy F/Ps-350/500 YS9680 Foot switch assembly BM30026 GASKET, FOR BOP CONTROL UNIT'S PNEUMATIC PUMP 1:60, MODEL: QYB42-125, MAKE: GUANGZHOU DONGSU PETROLEUM, P/N: 226QMD-09 Drill pipe tong accessories ZQ203-100 high pressure oil ball head 010804-04M Logging tool accessories horizontal well wet joint docking tool "0" hard plastic insulating ring 145-0229-00 STARTER; 10478986; 06k27A 24V; DETROIT DIESEL; ENGINE; ELECTRIC Nut:Lock [Mt] Bearing F/Top Drive Tds11S 51218-18 Flow Switch (M-200X Series) 30155689-3 NOZZLE, SPRAY-FLAT PATTERN 88990-10 Output module SIPLUS SM 322 Siemens 6AG1 322-11BL00-2AA0 35Ã??35 BOP accessoriesFZ35*35RS Piston RJ11172.14 Shim : Reservoir .005 F/Top Drive Tds11S 110147-2 ADAPTOR\CANRIG\N10610-2 For 1275AC-681 LABEL LINK INSTALLATION 121483 Relay DRM570024LT 7760056097 51216-24 DOWEL PIN: MOTOR HOUSING 1 X 3IN TDS Pin: Cotter 51403-20-S Triple cylinder pump FKQ 640-7 Pressure test pump check valve DLF5/16-00 Touring car hook accessories DG-250 lower bushing Galvanized welded steel pipe 38*3.25mm Q235B manual reversing valve\ZJ30 HD-2-FX PIN SECONDARY RETENTION 30172726-1 Touring car hook accessories YG160 Traveling block hook locking device SB-160 Drill pipe hanger accessories ZQ203-100 tooth plate 0101-27M Diesel generator set accessories ONAN-HDKAL-6.0 control monitoring panel 300-5026 TIMKEN bearing NU2220EMA AY11498-1075-RH Faucet accessories SL120 gooseneck assembly SXZ116130100001AA 190 series diesel engineParts engine system * water separator air filter sub-component 12VB.46.160F Screw compressor accessoriesLS10-30HH oil filter 02250096-783 50108-24-C H10466 190 series diesel enginePieces of cooling piping components * Hose Z12V.24.04B 1491.310/S29/6*4Brake*Brake adjuster arm Roller shaft accessories ZJ-30C three-position four-way valve SH361-3517/4900300052 VOLVOFM12 variable speed*Transmission shaft guide bearing
Perfomance of the main mechanisms: 1.Adopt lead edge feeder,wind absorbing auxiliary paperboard feeding,can make the cardboard feed favoringly.The volume of the wind can be adjusted accord the camber of the paperboard.(Kick feed as option) 2.The feeding roller is rubber with cylinder cushioning device,precise feeding,will not destroy the hardness of the cardboard when the feeding space is small. 3.The side battles adopt electrical control with data display.(here can add automatic pneumatic aligning device),the back baffle box adopt electrical adjustment,the front baffles space is manual adjustment. 4.With colorful touch screen,can be 360 degree adjust the phase of the die roller,and display the produce speed,setup the production quantity,when complete the production quantity,automatic warning 5.The rubber roller adopt mechanical control the position move left and right.The movement distance is 40mm 6.The space adjustment between rubber roller and die roller adopt self-locking structure,with cylinder big scope quickly adjust,decrease the rubber wear,increase the rubber life. 7.The unique speed compensation device can make the rubber roller rolling running with the die roller,make the surface speed of the rubber cushion is completely controlled by the die roller,the shape of the carton sheet will absolutely equal to the die pattern. 8.There is a rubber repair device with the machine,the rubber can be used after be repaired, 9.All the drive rollers adopted high quality steel materials,surface treated by lapping finish,hard chromium plating. 10.The drive gears adopt high quality alloy steel,after high frequency heating treatment and lapping finish.With automatic circulate lubrication,lubticate oil automatic balance device,keep the equal oil level in each unit. 11.Main motor adopt frequency converter adjust the speed. Technical parameters: Model Effective die-cutting area Paper-feeding area Working efficiency(sheets/min) SYD4210-1800 1800*1250 2000*1270 0-120 SYD4210-2000 2000*1250 2200*1270 0-60 SYD4210-2200 2200*1250 2400*1270 0-60 SYD4210-2400 2400*1250 2600*1270 0-60
This series of UPS power supply adopts the MOTOROLA 16 digit data bus microprocessor with powerful computing capability which ensures high speed, accuracy in detection, control over activity points of the UPS power supply, and ultimately high reliability of the product. It uses a unique AC-DC switching circuit to detect the output current and voltage of the alternating circuit. A high-frequency-pulse-width modulator is implemented which forces the phase of current conform to the voltage phase, achieving a high input power factor above 95%. Under normal circumstances, alternating current goes first through the AC-DC switching circuit to achieve DC BUS direct voltage, then it is converted back to an alternating voltage of 220v by the inverter. By going through these two process, the output voltage is ensured to have stable frequency, voltage, as well as clear sinusoidal phase shape. The inverter uses high-quality IGBT as its power regulating unit. IGBTâ??s high-frequency-switching characteristic optimizes the functioning frequency of UPS inverter to tens of thousands of HZ, which directly leads to higher inverting efficiency and the overall performance of the UPS power supply. Another advantage that high-inverting frequency brings is reduction of noise level. HBG series of UPS-power supplies can be placed directly in computer rooms without creating any distraction. Hongbaoâ??s online, high-frequency HBG series of UPS power supplies is affiliated by a communication interface RS232 together with Hongbaoâ??s power-supply-monitoring software, which enables the interaction between UPS power supplier and network servers. This means reading status of electricity can be monitored at any time in distance, accessing intelligent functions like: self-examination at regular time intervals, auto-saving data into desired destinations, automatic power on/off at fixed time, recording the status of the electricity and so on. When the alternating current breaks off, UPS power supply will timely inform the server to be ready for powering off and save all the data into the disk, then execute the normal power off order. This secures the safety of the data in the network system even under the network environment of unmanned operation.
Heat pump energy recovery dehumidifier & dryer working course: In an airtight drying chamber, the heat dry airflow from dryer contact with the surface and absorb the moisture of material by fan; the heat dry airflow absorb moisture become heat humid air, then through dryer the moisture coagulates drip and discharge by drainpipe. The dry airflow after heating by dryer become heat dry airflow again. The moisture of material keeps evaporating, coagulating, and discharging until it reaches the drying standard. Product Features Do not need heating device, lower energy consumption than other drying equipment about 40%~60%. Completely reclaim the latent heat of moist heat and make the air closed-cycle in the drying chamber. This design reduces the energy consumption, avoid environment and man-made pollution. Adopt automatic control system, the temperature can be adjusted according to the different product. The dryer has excellent character for solving many problems such as long time for drying, high temperature, drying unevenly and huge energy consumption. The material will not deform, not dehisce, not changes colour, not metamorphose, and not oxidate while drying. The machine is integral structure, and already debugged before delivery. It can be used after connecting to pipeline and electrical source. Application Areas The heat pump energy recovery dehumidify & drying is a method of low temperature (15~45/50/60â??), nearly air dry (5-10%). The evaporating speed of surface is similar to the speed which the inside moisture moves to the surface. This drying method the merchandise remains good quality, nice colour, high level, no pollution and saving resources. The heat pump drying can be widely used in papermaking, packing, printing and storage of tea, candy, foodstuff, ceramic, timber, Chinese traditional medicine, preserved fruit, fish, sausage, seafood, high protein food, varieties seed, edible mushroom, vegetable, fruit, potato chip, ginger slice, peanut, aquatic product, leather and heat sensitive chemical material etc. OTHER INDUSTRIAL PRODUCTION FACILITIES REQUIRING DEHUMIDIFY AND DRYING IN THE PROCESS. Heat Pump Energy Recovery Dehumidifier & Dryer Adopt most advanced energy recovery and transfer technique, dispense with electric heating, lower energy, energy conservation 40-60%. Closed cycle, first dewatering, then heating drying, all weather operation, not affected by seasons. The air relative humidity minimum achieves 5%-10% after to unit, the extremely dry air constantly absorbing moisture to materiel.it has unparalleled advantage to quality & time & energy efficiency. Can select mechanical or microcomputer or plc control. Can supply drying equipment for specific function.
Main machine 1.Frame structure Full steel structure, stress released, with accuracy well kept. Main component is designed and Finite Element Analyzed through ANSYS software. Main frame composes of uprights, working table, holding-down beam and oil tank. Ball transporter and supporting bar and squaring arm are fixed on working table. 2.Upper blade beam and blades Guillotine type blade beam, with rake angle adjustable The rake angle could be motorized adjusted by press button according to material and thickness. When shearing thin thickness sheet, the rake angle could be reduced, thus the distortion of the product and the burr could be minimized. Exchangeable Rectangle blade, with 4 cutting edges available. Blade material 6CrW2Si with hardness HRC53-60, with quality shearing result and long life. 3. Shearing length/stroke adjustment The shearing stroke could be adjusted through knob to the length of the product. Thus efficiency could be improved. 4. Cutting beam guiding and blade clearance The cutting beam is guided between roller guides. At the rear of the cutting beam there are two sets of upper and lower roller guides located at each end of the beam. Two spring-loaded rollers located at the front of the shear apply pressure to the cutting beam, forcing it against the back roller guides. The bearings of the upper roller guides at the back of the cutting beam are mounted on an eccentric shaft. Rotating this shaft causes the cutting beam to tilt, thus providing proper blade clearance to the shearing blades. The upper cutting beam inclined forward, with high section-cutting quality on the product. The blades clearance could be adjusted manually through hand-wheel according to material and thickness. Since the blade clearance is 0.1 to 2.5 mm, the shear can cut thickness 1mm to 40mm mild steel. 5. Hydraulic system LVD special hydraulic unit for heavy type shear is adopted. Hydraulic control components is from VICKERS,USA (or REXROTH, Germany) With in-series cylinders to achieve good synchronization. The sheet is pressed by hold-down before shearing and during shearing for safety and reliability. One-time machining on CNC lathe for cylinder body and piston rod. Horning for inner surface of cylinder, vibration super-fine machining on the outer surface of the piston rod. Oil seals from NOK, Japan (or Merkel, Germany) with low wear and tear, no oil leakage. High-pressure internal gear pump, with reliability and low noise. Over-load protection for hydraulic system 6. Electrical system Movable remote operation station with emergency stop. Main electrical components(contactor, button and switch) adopt product from TELEMECANIQUE from France. Requirement on working condition: Working temperature: -10 to 47 Power supply: 380V±5%, 50HZ, 3 Phase
Roller shaft accessories ZJ-40Drilling rig drum shaft high speed end water vapor hoist assembly JC32B2 Trunk accessories ZJ-40L drive intermediate shaft assembly Casing power tong accessories TQ340-35 jaw plate assembly 4-1/2" 56.680.00 56601-24 PLUG, PIPE 1 1/2" NPT TDS 190 series diesel enginePieces of gas starter * oil mist device parts 12V190-12VB.46.150F Casing power tong accessories TQ35-13 3/8" connector 20.13-01 Power selection box accessories SJX5227TSN Density Sensor PRESSURE SWITCH NOV p/no 78187087, ELECTRICAL RATING 15A DWER PART NUMBER 1950-10-2F Lifting sub 4-1, /2"1F Pin+NC50 (4 1/2" lF) box,bore: 2-1/4" , tapered 18 degree, AISI 4145HM, full heat treated, API 7-1 NIPPLE, PIPE NOV, 52048-36-B 100YZ NK400E Universal* Posttail light assembly Shrink: Tube Heat 84514-96-5 Touring car hook accessories YG170 buffer device T1N160 TMD63/630 FFC 3P Logging tool accessories 530 logging tool double lateral electrode 3997XA Pole clamp accessories ZQ203-100 joint body 010811-02M Drill pipe power tong accessories ZQ203-100 jaw plate pin 0101-03M BOLT, FOR ELEVATOR, MODEL: DDZ-250 P/N: 130701591 motor YB132S-4-B35 BUSHING 30151961 84665 SWITCH,TEMP Seal 7818880 Drill pipe tong accessories ZQ203-100 pneumatic tire clutch E01-00 Screw:Cap Hex Head Drilled 50012-24-C5D VOLVOFM12 coolingElectrical appliances * heater switch Construction machinery inner tube 6.5in 10in Angu BDFS-600 Low noise explosion-proof fan Explosion-proof multi-function controller LK-000 Self-aligning machine ND404 SH-0312NC-0100-W SPLIT PIN: 540, FOR DRAWWORKS, MODEL: JC 70D, MAKE: HH, P/N: GB/T91-2000 Tapered roller bearing 2097938E MAN33.373DFC variable speed power take-off bearing adjustment pressure cap 81.38506-0004 Drill pipe power pliers accessories ZQ203 U-shaped frame 125 0105-02M AIR BLADDER W27-20-902 O-ring 200 X 7.00 530301012000070015 Hydraulic tank accessories F-1600 Stem guide (top) AH1001010510 51405-10-S PIN, COTTER Power selection box accessories SNC40-17 Packing Copper Sleeve Assembly 5" IMPELLER(10.50INCH), 8 6 10.50INCH-P/N:G0006217 Deep groove ball bearing 6226 Winch oil pump drive shaftPieces ZJ-70 Roulette 108.37.510.03 Crane accessories ZJ40 rowrope assembly Hydraulic anchor FZ 163.96*76.2mm Liquid end accessories PCT521 TPH400 spacer ring 4-1/2" P90450450 ND3128 cooling system*cooler 641101308 Casing 8 6 14 SCREW, FLAT HEAD 50606-08-C CONNECTOR, O-RING BOSS/37' 56529-12-12-S Sleeve:Upper Stem Wear 2028635 56625-2.5-04 Cable, Composite;Shipboard-Multicore;3 Conductor; Electromagnetic eddy current brake accessoriesZJ-45 aviation plug P20-4 Roller shaft accessories ZJ-40Winch drum shaft JC32B2 Air Control Driller's Console FKQ12808 repair kit Detroit Diesel PartsElectrical instrumentation system*Valve chamber cover gasket 52460321 50008-28-C5D SCREW, CAP-HEX HD DRILLED, TDS 35Ã??35 2FZ35-35OType sealing ring32*3.5 JK00309-43 Winch oil pump drive shaftZJ-45 oil suction filter element
PRESSURE SWITCH OIL 87541-1 FZ35-70 shear ramLower cutter body seal RJ11148.09.10.01.08.00 S01-1386-01N Nut 600505-00-0600 for winch JC21D FY183 Hardened steel pinton rod Diesel generator set accessoriesC550D5 QSX15-G8 rectangular sealing ring 3678536 FZ35-35 gate sealRubber core 4-1/2" DFZ1310.01B-01-00 Insert valve 2.2.08.045 82704+30PLATE,SPACER Drill pipe tong accessories ZQ203-100 planetary gearbox assembly 0103-00M Trunk accessories ZJ-40L Sprocket Z=35 BA70001-06.17 SCREENS, PMDHPDX-A200 (HYPER POOL PYRAMID SCREENS API 200 MAN33.373DFC clutch* clutch pressure plate 81.303050.197 Square welded steel pipe 30*3mm Q235B CNC logging surface tool SKD-3000 VOLVOFM12 Fuel* Copper bushing for injector head Left bearing box p/n: P4600023AA 56501-16-16S CONN, EXT PIPE/37DEG 94521-1BN SHUTTLE VALVE CLAMP, LINK TILT, 250 TON 122599 Electric control box FKDQ640-7 Three-position four-way rotary valve 34ZS21-25 filter element 2.4.03.037 53916-G NIPPLE, CLOSE Hydraulic tank accessories F-1000 Internal connector R1 Casing power tong accessories TQ340-35Y lower bearing seat 52.100-15 L3.14-6.0 overhead hanging basket Cylinder liner piston accessories F-1000 Discharge cross 35�?35 BOP accessoriesFZ35-35 ram body 5" JK212-40S-4-1 Wheel Loader AccessoriesCG956G HH-0312NC-0150-GR8-W 76649 GASKET,INLET,MOTOR Primary Fuel Filter Element, p/n P550851. DONALDSON for DETROIT DIESEL SERIES 60. 25 micron CONT. S.3RT1026-1AG20 00A15C002.009 35�?35 BOP AccessoriesFZ35*35RS stainless steel retaining ring for holes �?165 Sleeve Kit SL225-06 Guide funnel 203-216 1.03.10.614 Drill pipe tong accessories ZQ203-100 lower support ring 0103-13M Forklift parts CPCD50-RG16 oil filter JX0818A 76344 SHIM Defoamer for oil well cement ST500L combination polyether Guide, Lower Suction Valve, P/N:1134286,MP-16 Eye Bolt 3/8 X 11/4, 9900208 116699-6 E01-1014-010 Pilot: Directional For Tds Ps-500A 7500753 86176-500 TDS SWINGBOLT ASSY IMPELLER\CANRIG\P10150-IMP For 1275AC-681 Hydraulic tank accessories F-1300 crosshead bearing, AH1301010414 NAMEPLATE 110181 71613 BREATHER;RESERVOIR;40CFM 56604-16 ELBOW, CAPPED HUB SIZE 1" (NPT) PLATE PIN RETAINER 30173503 Starter 24VDC,37A (E10366) Canrig Pneumatic Diaphragm Pump WL80ABAP/VT/TF/TF PROX SEN, 1-NO, 10-30VDC, 8MM N10057 Hydraulic tank accessories F-1600 Pressure gauge seat (flange connection) AH100101200100B2 56700-8-4-S REDUCER, PIPE-EXT/INT Washer: Lock-Tab, PH-100 30173900 CUTTING FERRULE JOINT, FOR DRAWWORK-HPU, MODEL: YZ096, MAKE: HONGHUA, P/N: 2C-22-26 Power end accessories SNC70-30 SPM600S rod oil seal P60-34-801 35�?35 BOP AccessoriesFZ35-35 cylindrical pin M12*60 COPPER SLEEVE- I , FOR DRAWWORKS, MODEL: JC70DB, MAKE: HONGHUA, P/N: ZX01.01.02 35-70 BOP AccessoriesFZ35-70 Secondary sealing grease JK00213-24 STOP WASHER, SIZE: 76, Q215, FOR SUBSTRUCTUR, MODEL: DZ278.00, MAKE: HH, P/N: 1300092534 50908-C WASHER, LOCK, REGULAR AY50859
SHAFT. Catalog number: 0102-05M. MANUFACTURER: JIANGSU RUSHI MACHINERY CO, LTD. Equipment: HYDRAULIC POWER TONG ZQ203-100. TYPE : GEARSHAFT PIN, CLEVIS 30172181-01 Remote Console Accessory FK75-2 globe valve GYJZF-00-00 1/2" General test mining tool casing centralizer 245 ultra-light swirl rigidity M11-1016-010 PRESSURE TEST JOINT PT-3 FOR DISC BRAKE HPU YZ.100S-096 Screw compressor accessories LS12-50HH filter 241771 YO 110/120V E1/6 Drilling rig top drive accessories DQ40/DQ50/DQ70 back pliers 5" V-BELT FOR F-1600HL ZPEC MUD PUMP 6ZV25J-8500 Trunk accessories ZJ-40L Parallel transmission box with pump shaft assembly BA70002-06.00B VOLVO series diesel engine parts fuel * fuel filter 21492771 Submersible pump QY15-26 2.2kW YB90L-2 53732-B CROSS, PIPE 74191 CONNECTOR,COMPRESSION*SCD* VOLVO series dieselMachine parts Generator * Oil pressure gauge 35�?70 BOP AccessoriesFZ35-70 hexagon socket screw JK00213-44 FRONT SEAL, 2-7/8"-5" VARIABLE RAM, FOR BOP 13-5/8" 5000 PSI, MODEL: 2FZ35-35, MAKE: RONGSHENG, P/N: RS11172.16.02 Tee 56530-12-12S SLEEVE FOR HYD DISC BRAKE, MODEL: PSZ 75A, MAKE: HH, P/N: PSZ75A-2-15 CHECK VALVE, PILOT TO OPEN (CKCB-XCN) 93547-1B30N Drilling hoist rope 45mm 200m 6*36WS 1770MPa smooth surface VOLVO series dieselMachine parts cooling system * liquid level sensor 8140024 Washer: Lock Internal/Star, 40MM 86872-40-S High energy mixer accessories JR5321TSN High energy mixer breather valve B030000512A CONTROL SYSTEM, TK01-01-00A BRAKE VALVE LT07MKA-2X Fitting For Varco Tds 56606-8 700048310 HEX HEAD CAP SCREW,7/8-9 X 2 1/2 J429 GR5;ZN Motor ball bearing Mod. 5GEB20C2 SER:RR10090002A Canrig Detroit S60 DieselAccessories fuel system * hand oil pump Drill pipe power tong accessories ZQ203-100 Straight connector 010801-01MI quick coupling 3/8NP H3-62 PIN, CRANK 30158164 LINK 1 COLLAPSIBLE 30170445 CABLE GLAND NPT 3/4 83444-06 Electric control box FKDQ640-7 PLC controller ILC 151 ETH High pressure joints and accessoriesPress nipple 2-7/8" MAN33.373DFC Engine* Fuel Pump 105220-5960 OIL SEAL 80X105X12MM Siemens motor blade 5.145.71322.40 001 Valve pressure exhaust valve BG80-23 safety caliper cylinder assembly for winch JC70DB/JC102TC Drill pipe hanger accessories ZQ125 upper ring gear 19.300.01 Desander CSS 300mm 2 STRAINER, SUCTION 122253-24 E33-1006-010 GASKET, �¦462:�?1, ROTARY TABLE, ZP375,HH ZB013.01.02.05 Drill pipe hanger accessories ZQ-100 transfer cylinder piston rod bit breaker for 8 1/2" Tricone bit LINER, STABILIZER 30158690 Winch intermediate shaft accessories ZJ-45 Gland 106.02.20.42 Valve: Thermostatic 3-Way 97575 SCREW, CAP-HEX HEAD 50006-24-C5D Oil and gas layer protection agent ST-2 Wire Cable Assy.,18/C M614005490-01-25 35�?35 BOP accessoriesFZ35*35RS piston FZ897.1.9 Square welded steel pipe 40*40mm Q235 Adjusting gasket1 1.03.14.331 Cable: Shipboard Multicore, 7C x 1.5 mm2 56625-1.5-07 Touring block hook accessories YG-170 outer spring
Control Relay WEIDMULLERDRM270 024L 24VDC contact point-10A8pin Stop valve 4403000030 Bolt 1468.032.000-10 C65N-C16-1 POLE BREAKERS 51270424-2/3 Port air operated valve K23JK-F40 Harness 29542681 Electric Motor ABB M2QA100L2A 3kW 2860RPM IMB3 KEY: 2 X 2 X 203GH3101-03.01 9370240421 Shell Valve Hyd Thermal bypass H24-2000-010 Seal 120 X5.7 GB1235-76/XSL225 High pressure drilling hose for monofold ZG100-35 4NPT/35MPa Ball valve 4403000050 Ring 202.57 X7 1134299 Weatherford HARTING 9990000052 Air filter EF6-80.1 Gasket 107.35.110.09 Lanshou LS 57987877 Filter element Gear-shaft HH8S110WV Weatherproof Strobe Light Profi Flash GH3101-15.02Short connector:NPT 1/2 GH3101-10.00Breather cap Parasitic gear group 52.230.00A Wireline Unit FILTER ELEMENT 01.0102.035 Bearing NU324 Valve plate B280X2.5-3H Pilot Light CL2-523Y YELLOW AC220V 1SFA619402R5233 ABB WA71-32 IND,12,TTL&,P/M,340KN SLP,10/12 LS,ENG/SI METRIC Sleeve ZQ203-085 PLD-16R YHW156 Explosion-proof integrated universal camera CEP Speed sensor 111-412-000-013/AH92773/992012 S3960/A1-B1-E005-FO-G000-HO5 PRESSURE GAUGE 21X53 CBM 3000 PSI 9692105 GH3101-02.02Sleeve, main bearing (right) SCREW CAP-HEX HD DRILLED 50012-20-C5D Air filtering and reducing vave QFH-261 0~0.6MPa(85PSl) Bearing GB5801-86 TQ34001137 DMDP-A Crane engine model 6CTA 8.3-DCM ESN 21648450 C4-C3 Inlet Gas Temperature SBWZP-2480 K 0-1000C Liquid Crystal Display Cuff X 01-00-011 disc brake WPT to XJ-450S TDS-8SA O-RING 357 30182002-9/6300-138 5019754 MOUNT,UPPER,SPRING,9 GRABBER Liner-6 5465675 HANDWEELSCREW J014832 BG322004-031300 Oil ring unit Transformer INPUT: 380V, OUTPUT: 110V JBK5-250 TH P=250VA 50/60HZ T40/E IP00 GB5226-85 VDE 0550 Make: SULLAIR 5536641800 FILTER Vaccum Circuit BreakerYGM-12/1250-31.5 12KV,1250A GH3101-02.07Locating ring(I) 2.4.20.417 Hose assembly EXecution mech aniz.brake PZ30 190*330 Oil seal AH1001010416 BOMCO Brake band 19.620.00 Hose assembly 32II-2800 hydraulic pump line 1101020086 XJ045SJHZC016 to XJ-450 unit Planet cage assembly ZQ162-50 Pump assembly 113935 CYL,HYD,BORE 3 /,ROD 2,STRK 47.94 Pressure relief valve JYS-21, 9161200000 solenoid valve 29537373 YHQ20 explosion-proof dome camera 57822298 Oil filter Cap seal NB800G.05.04/3NB-800F RGS4/80A FUSE Air cleaner assembly RB Waukesha AA214290A PMS board MK8856364 Jaw replacement 9 5/8 245 complete with roller pin and biscuits 56.630.00 DB3 / SM87HXB Exd(e), Heavy Duty Industrial & Marine, Weatherproof 352 Fitting Hyd Female JIC X Male JIC 90 deg 3/8 X 3/8 Arrester valve J-L10 Splash guard HH11309.04.009.111 Haihua Thermostat CUMMINS201737 462-1171 Oil filter Pin 45575 PACKING SHAFT 661007005 25014-04M-8
A professional intelligent machinery Remote control lawn mowers are our current main products, widely used in lawn mowing, cutting and bush trimming, suitable for slope, steep incline, wasteland, roadside, river levee, orchards, field , villa lawns, soccer field, gardens, etc. focus on the research & development of remote control and auto pilot intelligent machinery, such as remote control lawn mower, auto pilot cutter, wireless remote controlled robot chassis kits, autonomous running tracked robot platform, etc. The products adopt the world s most advanced wireless remote control technology, intelligent autonomous control technology, and Italian mowing technology. We can produce approximately 1000 units of remote control slope mower per month. The machines undergo 100% indoor and field tests to ensure they are qualified and ready to use before delivery. We offer professional technicians who can provide online and on-site training for free. Our current products include: Remote Control Lawn Mower, Crawler Remote Controlled Brush Mower, Rubber Track Remote Operated Slope Mower, Wireless Radio Control Mowing Robot and Wheel Radio Controlled Grass Cutter. Features: 1) Security The remote control lawn mowers avoid putting staff in unsafe situations to mow, and away from snakes, spiders, insects, etc. 2) High efficiency Travel Speed of up to 6 km/h. Remote controlled lawn mower is 16 times more efficient than hand cutting. 3) Easy to use One key electric start, and adjust the cutting height quickly and easily by remote control. 4) Easy to maintain The robotic lawn mower has a long productive lifespan, low maintenance cost, and its parts are easy to replace, as and when required. 5) Easy to transport and store Weighing in at only 230kg. With backup battery, can move the mower without starting the gasoline engine. 6) Wide range of applications It is widely used in villa lawns, football fields, mountain slopes, communities, greenhouses orchards and gardens. Specification: Model: SSW800-150 Cutting Width: 800mm Walking Speed: 0-6km/h Working Degree: 0-50 Adjustable Cutting Height: 10~180mm Min Ground Clearance: 20mm Remote Control Range: 200m Engine Fuel Type: Gasoline Power / Emission: 15Hp / 452cc Engine Type: Single cylinder, four stroke Start Method: Electric start Emission Standard: Euro 5 Fuel Tank: 10L Working Time: 6h Walking Motor Motor Type: Brushless electric traction Voltage / Power: 24V / 1000W Dynamo: 24V 2500W Battery: 24V 40Ah Machine Size: 1070 x 1170 x 630mm Package Size: 1170 x 1270 x 930mm Machine Weight: 230kg
SUPERSHINE ROBOT is a professional intelligent machinery manufacturer located in Weifang City, Shandong Province, China. Remote control lawn mowers are our current main products, widely used in lawn mowing, weed cutting and bush trimming, suitable for slope, steep incline, wasteland, roadside, river levee, orchards, field weeds, villa lawns, soccer field, gardens, etc. SUPERSHINE ROBOT focus on the research & development of remote control and auto pilot intelligent machinery, such as remote control lawn mower, auto pilot weed cutter, wireless remote controlled robot chassis kits, autonomous running tracked robot platform, etc. The products adopt the worldâ??s most advanced wireless remote control technology, intelligent autonomous control technology, and Italian mowing technology. We can produce approximately 1000 units of remote control slope mower per month. The machines undergo 100% indoor and field tests to ensure they are qualified and ready to use before delivery. We offer professional technicians who can provide online and on-site training for free. Our current products include: Remote Control Lawn Mower, Crawler Remote Controlled Brush Mower, Rubber Track Remote Operated Slope Mower, Wireless Radio Control Mowing Robot and Wheel Radio Controlled Grass Cutter. Features: 1) Security The remote control lawn mowers avoid putting staff in unsafe situations to mow, and away from snakes, spiders, insects, etc. 2) High efficiency Travel Speed of up to 6 km/h. Remote controlled lawn mower is 16 times more efficient than hand cutting. 3) Easy to use One key electric start, and adjust the cutting height quickly and easily by remote control. 4) Easy to maintain The robotic lawn mower has a long productive lifespan, low maintenance cost, and its parts are easy to replace, as and when required. 5) Easy to transport and store Weighing in at only 150kg. With backup battery, can move the mower without starting the gasoline engine. 6) Wide range of applications It is widely used in villa lawns, football fields, mountain slopes, communities, greenhouses orchards and gardens. Specification: Model: SSC550-90 Cutting Width: 550mm Walking Speed: 0-6km/h Working Degree: 0-40�° Adjustable Cutting Height: 10~150mm Min Ground Clearance: 20mm Remote Control Range: 200m Engine Fuel Type: Gasoline Brand: Loncin Power / Emission: 9Hp / 224cc Engine Type: Single cylinder, four stroke Start Method: Electric start Emission Standard: Euro 5 Fuel Tank: 2L Working Time: 2h Walking Motor Motor Type: Brush electric traction Voltage / Power: 12V / 600W Dynamo: 12V 1500W Battery: 12V 12Ah Machine Size: 930 x 860 x 580mm Package Size: 1060 x 960 x 810mm Machine Weight: 150kg
Options: 1. Servo Motor drives horizontal sealing 2. Hole punching device 3. Gusset bag forming device 4. Tear notch device 5. Exhaust air function 6. Coding device(ribbon/thermal transfer) 7. Gas flush device 8. Product Discharge conveyor 9. Chain bag withbatch cut 10. Refilling device for the scale Application: Dry & Processed food, fresh food, snack food,seeds(pulses), nuts, coffee(granules/beans), tea, sugar, grated cheese, bakeryproducts, candies,Pet foods,bolts,washers,electrical and plumbing parts,etc. Features: 1. Automatic combination weighing and vertical packing combined in one single unit machine(2in 1 technology). 2. With one frame,one electric cabinet, one electric plug only. 3. Strict height control and space saving, easy for cleaning and maintenance. 4. Suitable forsmall and medium packaging application with high speed and accuracy request. Parameter: Model NO. GPMW-420E Filling weight (g) 10-800 Scale hoper number 10 weighing hoper size 1.6L weighing hoper layer 2 layers Bag length(mm) 80-180(bag length longer than 180mm will pull film two times) Bag width(mm) 80-200 Film width(mm) Max.420mm Max. Speed 20-60pcs/min. FAQ Q1: How do I find a Packing machine model suitable for my product? A: PLS Tell me about your details information and requirement. 1. What is your packing object details(size). 2. What process you want our packing machine be in charge of? 3. What is the situation of your working environment and former working process. 4. Your requirement for the machines working capacity Q2:Are you factory or trading company? A:We are manufacturing&trading company with Shanghai Sales Office and Jiangxing production base.Welcome to visit us. Q3:What about the production lead time? Regarding Production Time;usually we need 3 working days after technical details and order confirmation for individual machine. A:But for the whole packing line,we need 20-30 working days. Q4:What about payment terms? A:We accept TT/Western Union/Cash/LC/Trade assurance order,With 30% deposit as advance payment and 70% as balance payment. before machine leaving the factory. Q5:what is your warranty and after-sale service? A:One year warranty and lifelong after-sale service via. skype/Email/mobile/Whatsapp/Wechat/etc. also technical service overseas is available. Q6:Why choose our machine? A:1-Competitive Price with great performance 2-Excellent technical support and Professional Service 3-Own design department meets your various OEM/ODM need. 4-Over 15 years experience in packing machine field
PET (Polyethylene Terephthalate) Resin is cream or pale-yellow crystal, with smooth and shiny surface. Resistance to creep deformation, fatigue resistance, abrasion resistance and dimensional stability are perfect. Small wear and tear but high hardness, its toughness is the largest in thermoplastic. The electrical insulation of PET is perfect and little be affected by temperature, however, poor corona resistance. PET is non-toxic, weather resistance, and anti-chemical stability is very good. PET is low water absorption, resistance to weak acids and organic solvents. Intolerance of hot water immersion and alkali. Feature: 1.Oil resistant, fat resistant, acid resistant, alkali resistant, resistant to most solvents. 2.Excellent resistance performance of high and low temperature. 3.Non-toxic, tasteless, health and safety. 4.Transparent, UV blocking, good glossiness. Specification Item Unit Index Intrinsic viscosity (IV) dL/g 0.80 �± 0.02 Crystallinity % â?¤60 Acetaldehyd Content ppm â?¤1.0 Color (L-value) â?¥83 Color (b-value) â?¤1 Melting point �°C 243 �± 2 Moisture Content %/w â?¤0.4 Weight of 100 chips g 1.55 �± 0.10 Dust content ppm â?¤100 Application 1. It is widely used in packaging, electronics, health care, construction, automotive and other fields. 2.It is used in synthetic fibers, and engineering resins often in combination with glass fiber. 3.Beverage, food and other liquid containers.
Machine features: The function of automatically install and unload of blades, suitable for precision cutting board saw, electronic cutting saw, aluminum alloy saw blade, multi-blade saw and other series of saw blades. One person can operate more than 10 machines at the same time, greatly save labor cost. Silver solder bending unit continuously variablely programmable in all dimensions. Three groups of rails are adopted for the transmission of tungsten carbide tooth , which improves the running accuracy and service life of rails. Industrial PC with 10inch touch screen system with both language and logo for parameter setting, easy set-up and operation. Automatic teeth selection, feeding, dosing, silver solder foil cutting and folding just through one-stage processing. Welding the tip onto the circular saw blade by control the temperature so that the temperature controlled brazing and annealing cycle allows brazing joints perfectly. Automatically pick up of the brazed circular saw blade and placing it onto the upper pin of the loading magazine in ergonomic control position for the operator . Technical data: Diameter of saw blades:120mm~500mm Rake angle:-5~+25 Tip width: 1.5mm~6mm Brazing accuracy: 0.05mm Thickness of saw blades: 1.0mm~5.0mm Speed of brazing : 6~13s/per tooth General power: 6.0kw The width of silver solder foil: 1.5mm~6mm Diameter of silver wire : 0.5mm Water pressure : 3KG Air pressure: 5KG Electricity: 220 V single phase 50 Hz (wire bigger than 6mm2) Gross Weight: 800KG Dimension : 1600mm *1200mm *1700mm Time of change blades:15~20s/pcs Options: Camera inspection system Ceia induction heating system
HP CMB X2 Printing Module Features and Benefits - The HP Scitex X2 Printhead consists of a chip with 128 nozzles fixed to an integrated circuit board. Ink is ejected from each side of the chip (64 nozzles per side) at a rate of up to 30,000 drops per second per nozzle. Drop volume is up to 50pl. - The Printhead Chip has 128 nozzles with a native resolution of 100 nozzles/inch, and it can be assembled into multi-printhead modules offering resolutions up to 800 dpi. - The size of the delivery end of the HP Scitex X2 Printhead is 8mm x 64mm. With a slim profile, the printhead is ideal for building multi-printhead modules with very high nozzle density. - An ink channel at the top edge of the printhead supplies all nozzles. Ink up to 15 cP in viscosity can be used in the HP Scitex X2 Printhead. - The Electronics Package, with printhead controllers, voltage regulators and piezo actuators comprises two identical electrical assemblies. - No adhesives are used in fixing the silicon and glass. Anodic bonding is used, forming a permanent chemical bond and hermetic seal between the constituent materials. Printer compatibility: HP Scitex FB7500 / Scitex FB7600 DUTA-PRINT is a professional supplier of printer unit, printer and printing parts, ink, membrane, filter, all etc. parts and consumable whole sale and manufacturer located in Jawa Timur, Indonesia. Our business engaged to digital printers, filter, ink, consumables and printing solutions. We have our own tech team that help custom to install, operate the machines, they are fully trained and with up to 10 years experience on digital printers. we provide printing solution advise to solve customer's specific printing need and all repair when it needed the parts to supply. We helped our customer save hundreds and thousands dollars over the last 5 years.
