V3 Borewell Submersible Pumpset
Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
V4 Borewell Submersible Pumpset
Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and
Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP)
- Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply.
Single Phase available in 0.5 HP to 5.0 HP
Three Phase available in 1.0 HP to 6.0 HP
- Speed : 2880 RPM
- Head Range : 10 Mtr. To 340 Mtr.
- Discharge Range : 450 LPM to 12 LPM
- Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0
- Degree of Protection : IP 58
- Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph
- Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs,
2.2kW, 7.5 kW -1500 lbs.
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph
Direct Online (D.O.L)
- Maximum Starts Per Hour : 20 Times
Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.
Salient Features
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series
- 20 Mtr. Head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust
loads
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS Pumps are available
Specification
Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph
- Power Range : 7.5 kW to 75 kW (10 HP to 100 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Thrust Load : 7.5 kW -30 kW -10000 lbs
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 440 Mtr.
- Discharge Range : 2400 LPM to 300 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : Star Delta (SD)
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.
Salient Features
- Cast iron casting bowl and SS-410 grade impeller in mix flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
Specification
- Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW
- Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2880 RPM
- Head Range : 18 Mtr. To 650 Mtr.
- Discharge Range : 1860 LPM to 55 LPM
- Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0
- Degree of Protection : IP 58
- Direction of Rotation : Electrically Reversible -3ph
- Thrust Load : 11.2 kW -37.3 kW -8000 lbs
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series.
- FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in
Mix flow series.
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set.
- Dynamically balanced rotating parts ensures minimum vibration and longer life.
- Designed for wide voltage fluctuations.
- Motor portion covered with corrosive resistance Stainless steel (SS 304) shell.
- More durability and hygiene & High operating efficiency.
- Specially designed thrust bearing to withstand high axial thrust load.
- Extremely hardwearing water lubricated bearing.
- Thread type motor construction ensures service feasibility.
- Designed for wide voltage operation.
- Best alternative for JET & Compressor pump set.
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 55 kW to 112 kW (75 HP to 150HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2900 RPM
- Head Range : 12 mtr. To 300 mtr.
- Discharge Range : 3600 LPM to 960 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Maximum Starts Per Hour : 10 Times
12332 Zl38 11 Submerged Water Pump Suppliers
Short on time? Let Zl38 11 Submerged Water Pump sellers contact you.
V5 Borewell Submersible Pumpset
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are
assembled under pressure and rigidly locked in stainless steel stators shell.
Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)
Specification
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5 , 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell
Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial
thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)
Specification -
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5, 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m²/sec (max.)
- Ph Value : 6.5 to 8.5
V6 Borewell Submersible Pumpset
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade
Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.)
6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade
Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Salient Features
Highly efficient 3-phase water filled motor
- Easily rewindable
- Dynamically balanced design
- Extended life with flawless performance
- Thrust bearing : Carbon + S.S. material for High thrust load capacity
- 100% EC grade copper winding
- Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps.
- Zero maintenance
- Superior performance
- Sand proof operation
- Highly efficient 3-phase water filled motor
Product Specification
Power Range : 1.0 HP to 20.0 HP
Operating Speed : 0 - 2890 RPM
Operating Frequency : 0 - 50 Hz
Input Solar DC Power Range : 900 Wp, 20000 Wp
Input Solar DC Voltage Range : 110 Vmp - 600 Vmp
Head Range : 30 Mtr , 220 Mtr
Discharge Range : 10000 LPD - 420000 LPD
Type of Duty : S1
material of construction - motor
Part Grade
Body Lock : Spring Steel
Stud Ring : M.S. (Zinc Coated)
Stator Stamping : CRNGO - M45 Silicon
Winding Wire : 100% EC Copper
Shaft : SS-420
Rotor Stamping : CRNGO - M45 Silicon
Copper Lamination : 100% EC Copper
Upper Housing : SS-304
Lower Housing : SS-304
Connection Piece : SS-304
Oil Seal : NBR
TB Set : Carbon + SS
Base : SS-304
Drain Plug : Brass
Couple Sleeve : Stainless Steel
Water Bolt : Brass
MATERIAL OF CONSTRUCTION PUMP
Part Grade
Suction : SS-304
Couple : Stainless Steel
Couple Counter : SS-304
Rubber Seal : NBR
Bush Seal Cover : SS-304
Bowl : SS-304
Impeller : SS-304
Key : SS-410
Bowl Bush : NBR
Bush : LTB-4
Middle : SS-304
Cap : NBR
Outlet : SS-304
Monoblock pumps -
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.
salient features
- High operating efficiency resulting in lower power consumption
- Good suction lift characteristics
- Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP
- Specially designed for wide voltage operation
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life
- Back pull-out design for easy servicing and repair
- Double shielded ball bearings, so no need of external lubrication
- All Model fitted to Mechanical seal.
specification
- Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP)
- Version : Single Phase, 220-240V, 50Hz AC Supply
Three Phase, 380-415V, 50Hz AC Supply
- Speed : 2880 RPM
- Maximum Total Head : 32 Mtr.
- Maximum Flow Rate : 940 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Mechanical Seal
- Type of Duty : S1 (Continuous)
- Method of Starting : Permanent Split Capacitor (PSC)
- Direction of Rotation : Three Phase, Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40,
50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm)
characteristics of clear cold water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Part Name Material
Mechanical Seal : Carbon & Ceramic
Motor Shaft : EN-8
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Plastic
Monoblock Pumps
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.
salient features
High operating efficiency resulting in lower power consumption
- Good suction lift characteristics
- Specially designed for wide voltage operation.
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life.
- Back pull-out design for easy servicing and repair.
- Double shielded ball bearings, so no need of external lubrication.
- Mechanical seal is provided as per customers requirement
Specification
- Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP)
- Version : Three Phase, 380-415V, 50Hz AC Supply
- Speed : 2880 RPM
- Maximum Total Head : 65 Mtr.
- Maximum Flow Rate : 1450 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Stuffing Box
- Type of Duty : S1 (Continuous)
- Direction of Rotation : Three Phase, Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80
100 X 80 and 100 X 100 (All size in mm)
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 mÃ?/sec (max.)
- Ph Value : 6.5 to 8.5
Material of construction - motor
Part Name Material
Gland Dori : Graphite String
Motor Shaft : EN-19 with SS SLEEVE
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Aluminium
Monoblock pumps
Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the
frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise
thereby increasing the life cycle of the motor.
Salient Features
High operating efficiency resulting in lower power consumption.
- Good suction lift characteristics.
- Specially designed for wide voltage operation.
- Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life.
- Back pull-out design for easy servicing and repair.
- Double shielded ball bearings, so no need of external lubrication.
specification
- Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP)
- Version : Three Phase, 380-415V, 50Hz AC Supply
- Speed : 1440 RPM
- Maximum Total Head : 12 Mtr.
- Maximum Flow Rate : 3160 LPM
- Maximum Suction Lift : 7 Mtr.
- Degree of Protection : IP 44
- Class of Insulation : B0
- Maximum Ambient Tem. : 40 C
- Sealing : Stuffing Box
- Type of Duty : S1 (Continuous)
- Direction of Rotation : Three Phase - Electrically Reversible
- Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150
(All size in mm)
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Part Name Material
Gland Dori : Graphite String
Motor Shaft : EN-19 with SS SLEEVE
Motor Body : FG-250
Bearing : SKF
End Cover : FG-250
Bracket : FG-250
Flange : FG-250
Casing : FG-250
Impeller : FG-250
Cooling Fan : Aluminum
Dipotassium Phosphate, E340, CAS no.7758-11-4, white powder, water-soluble salt used as a fertilizer, food additive and buffering agent. The manufacturing process of Dipotassium Phosphate is via chemcial synthesis, Phosphoric acid and Potassium hydroxide as raw materials. Dipotassium Phosphate is a common source of phosphorus and potassium. It functions as a stabilizing salt, buffer, and sequestrant. It is used as a food additive or preservative is highly effective in preventing coagulation, and is commonly used in non-dairy creamer as a buffering agent.
As an experienced Dipotassium Phosphate manufacturer and supplier, we has been supplying and exporting Dipotassium Phosphate for almost 10 years, please be assured to buy from us. Any inquiries about price and the market trend please feel free to contact us, we will reply you within 1 working day.
Dipotassium Phosphate Specification
Item Unit Dipotassium phosphate 98%
Appearance White powder
K2HPO4ï¼?as dry basisï¼? %(w/w) min 98.0
Water-insoluble %(w/w) max 0.2
Arsenic (As) mg/kg max 3
Fluoride (as F) mg/kg max 10
Loss on Drying %(w/w) max 2.0
Pb mg/kg max 2
Non dairy creamer, E472e, CAS No.7758-11-4, food emulsifier, a substitute of milk, white to cream colored powder manufactured from dried non-fat milk. The raw materials including casein, oil, sugar, sodium, High Fructose Corn Syrup (HFCS)â?¦in the manufacturing process. Oil source: coconut oil, palm kernel oil.
As an experienced Non dairy creamer manufacturer and supplier, we has been supplying and exporting Non dairy creamer for almost 10 years,, we supply Non-Dairy Creamer for Milk Tea has a fat content between 30-34%; uses for Instant Cereal has a fat content between 30-32%; uses for for Infant Formula has a fat content between 30-70%; uses for for Cold Drinks has a fat content between 20-35%; uses for Coffee has a fat content between 26-30%; uses for Acidic Beverages has a fat content between 20-70%; uses for for Acidic Beverages has a fat content between 20-35%.
Please be assured to buy from us. Any inquiries about price and the market trend please feel free to contact us, we will reply you within 1 working day.
Produced according to customers demands.Including non-dairy creamer use in coffee mate, milk tea, ice cream, cereal, baking food, infant formula,acid beverage, Condiment and soup, etc.Cold Water Solution Non Dairy Creamer SpecificationApplication: iced drinksSolution temperature: 5 Dissolution time 25-30 secondsVegetable oil: sunflower seed oilSpecification: Fat content 25%-27% Protein content 1-2%Packaging: 25KG/BagShelf life: 18 monthsNo Sugar Non Dairy Creamer SpecificationFlavor: Vanilla; ChocolateApplication: drinks vegetable oil: palm oil, palm kernel oil, hydrogenated soybean oil specification: Fat content 20%-35% Protein content 0-5%Packaging: 25KG/BagShelf life: 18 months
Calcium Acetate Monohydrate, E263, CAS no. 5743-26-0, calcium salt of acetic acid, s a white, odorless, and tasteless crystalline powder. Also known as Calcium acetate, manufacturing process via chemical synthesis, calcium carbonate and acetic acid as raw materials. Calcium Acetate Monohydrate is mainly used in the production of candy products, desserts, and baked good (bread, cakes, pastries).
As an experienced Calcium Acetate Monohydrate manufacturer and supplier, we has been supplying and exporting Calcium Acetate Monohydrate for almost 10 years, please be assured to buy from us. Any inquiries about price and the market trend please feel free to contact us, we will reply you within 1 working day.
Calcium Acetate powder Specification
Product Calcium Acetate
CAS anhydride :62-54-4; monohydrate :5743-26-0 INS 263
EINECS 200-540-9 EEC E263
Structure Molecular
formula 1.Anhydrous:Ca(C2H3O2)2 2.Hydrates:C4H6CaO4H2O
3.C4H6CaO4xH2O(x<1)
Properties White loose fine powder.Odorless.Slightly bitter taste.Easy deliquescence .Decomposed into
CaCO3 and acetone when heated to 160 C .Soluble in water,slightly soluble in ethanol.
Quality
Specification Item Standard GB15572-95 JECFA97 FCCV USP35 EP7.0
Content(dry basis) 98.0%~102.0 98% 99%~100.5% 99.0%~100.5% 98.0%~102.0%
PH(5%) 6.0~8.0 6 ~ 9
(1 10) 6.3 ~ 9.6
solution
(110). 7.2~8.2
Water insoluble
matter 0.3%
Nitrate passed test passed test
Sulfate GT-30 0.1% 0.1 0.06% 600ppm
Fluoride 0.005% 0.005%
Chloride GT-30 0.05% 0.05 0.05% 330ppm
Pb 0.001%
Heavy metals as Pb,GT-16-1 0.0025% 2 mg/kg 2mg/kg 0.0025% 20ppm
Sr 0.05% 500ppm
K 0.05% 0.1%
Na 0.5% 0.5%
As GT-3 0.002% 3ppm% 2ppm
Magnesium &
alkali salt 1% 0.05% 500ppm
Al passed test1ppm
Barium passed test passed test 50ppm
Moisture
GT-32 7% 11% (155o
to constant
weight;
monohydrate) 7% 7.0% 7.0%
Anthracite Coal, Bituminous Coal, Charcoal, Charcoal/Briquette Making Machinery, Coconut Shell Charcoal, Coking Coal, Diesel, Indonesian Coal, Other Charcoal, Sawdust Briquette Charcoal, Solar Cells, Solar Controllers, Solar Inverters, Solar Lamps, Solar Lighting Kit, Solar Lights, Solar Power Equipments, Solar Refrigerator, Steam Coal , Wood Charcoal, Bamboo Charcoal, Briquette, Charcoal Briquette, Coal, Coke, Common Charcoal, Firewoods, Lignite Coal, PetrolSolar Batteries, Solar Components , Solar Fans, Solar LED Street Lights, Solar Lantern, Solar Lightings , Solar Panels, Solar Power System, Solar Water Pump, Thermal Coal
Technical Parameter
Character ModelZL32-02
Working Voltage RangeDC: 6V-24V
Rating Power6V: 2-6W / 12V: 3-6W / 24V: 4-7W
Static Water Head1.0-2.5 M
Static Flow Rate2.0-3.5 L/min
LifespanContinuous operation under normal surrounding >20000Hr
Working EnvironmentLiquid: From weak acid to weak base?work in water (Submerged)
Max NoiseUnder normal working status, 1M distance over test instrument
12332 Zl38 11 Submerged Water Pump Suppliers
Short on time? Let Zl38 11 Submerged Water Pump sellers contact you.
