0.5 hp regular-30m head-2.6amps-2000lph per hour at 18m. 10kgs
Structural characteristics Unique motor design (capacitor start and run type) Forged brass impeller Internally mounted mechanical seal Low power consumption Fitted with terminal block Light in weight-portable Compact mechanical design Better aesthetics and finish Operating conditions Clean water not containing abrasive particles Liquid temperature up to 60ª c Ambient temperature up to 40ª c Total suction lift up to 6 meters Motor 2-pole, single phase, 50 hz, 220-240 v with thermal overload protector Capacitor inside/outside the terminal box Insulation class b Protection ip 51
Self-priming sewage pump The volume ratio of solids in the medium Diameter of maximum grain free pass 76 mm trailer sewage pump
Self Priming Pumps (Super Suction Type) Available in 0.5 H.P. & 1 H.P., Head: Up To 50 mtrs, Discharge: Up To 3000 lph, Supply: 1-Phase, Delivery Size : 1 X 1, Winding : Copper (E.C.Grade), Impeller: Brass, Motor Body: Aluminium / Cast Iron, Available With Thermal Over Load Protector (T.O.P.).
Self-priming pump KD series Motor Model:KD-Self-priming pump Materical:PP Power:10hp Pole:2P Primary ring:Silicon Mating ring:Ceramic Rubber:EPDM Spring:SUS316 Frequency:50HZ Caliber:3"X3" Max.capacity:1133l/min Max.head:23.5m Weight:140.0kg
Self-priming pump CBH-80 and its units (hereinafter referred to as pumps or units) are designed to pump liquids without mechanical impurities. Pump CBH-80 is designed to pump the following liquids: water, gasoline, kerosene, diesel fuel and other liquids with a viscosity of not more than 2 10-6m2/s at a temperature from -40 to +50 and a density of not more than 1000 kg/m3. Symbol of a pump or electric pump unit: C self-priming H-pump 80- DN inlet and outlet pipe, mm Specifications of Pump CBH-80 The main technical characteristics of the pump are shown in Fig . 1 and in Table 1 at testing it on water at a temperature of 20 C and a rotational speed of 1450 rpm.
Self priming series garden water pump JET Series pump is a jet pump or a full lift self-priming pump which is consisted of centrifugal pump and jet nozzle. These series pumps possess certain flow quantity, higher head. It could lift the water to 9 meters of vacuum height.This series is suitable for using on water withdraw of household, water supply of high building, irrigation of garden and farm, etc. Product Feature: -Power:0.5HP,0.75HP,1HP -Impellor : Brass -Casting iron pump body -PPO diffusor -Aluminum motor housing -Insulation class B -protection IP 44 -stailess steel shaft &good quality bearing -Full copper wire coil
JET-M SERIES SELF-PRIMING PUMP JET-M series are suitable for pumping clean water.They are particularly suitable for domestic applications such as supply water from well,pool etc,the automatic distribution of water by surge tanks and pressure switch,gardening,andincreasing of water pressure. Working conditions Max Temperature of Fluid up to+40 Max pressure:8bar. Max Ambient Temperature up to 40 Standard data and equipment: Single phase 220v/50Hz,Brass or plastic impeller,carbon steel motor shaft, with thermal protector insitde. Other model and material such as tThree phase,110v,60Hz,dual voltage, stainless shaft,etc,will be available upon request.
Self-priming jet water pump (jsw) Structural characteristics**** A. Pump body: cast iron, with uni iso 228/1 gas threaded suction and delivery openings. B. Motor bracket: aluminum motor bracket, reducing difficulties when starting the pump after long periods without use, due to the impeller blocking. C. Ejector union: approved for drinking water. D. Impeller: brass with centrifugal radial flow type E. Motor shaft: anti-rust motor shaft F. Mechanical seal: ceramic and graphite. G. Motor: the pumps are coupled to an asynchronous, high efficiency toyoo induction motor of suitable size, which is quiet, closed and externally ventilated, suitable for continuous duty. Insulation class b. The thermal cutout relay motor protector is incorporated in single phase motors. Three phase motors require an adequate external motor protector, with connections according to current standards. H. Protection: ip 44.
Structural characteristics Unique motor design (permanent split capacitor type) Gun metal impeller Internally mounted mechanical seal Low power consumption Fitted with terminal block Light in weight-portable Compact mechanical design Better aesthetics and finish Glass fill nylon nozzle and venturi Operating conditions Clean water not containing abrasive particles Liquid temperature up to 60ª c Ambient temperature up to 40ª c Total suction lift up to 6 meters Motor 2-pole, single phase, 50 hz, 220-240 v with thermal overload protector Insulation class b Protection ip 51
Non self-priming pump NAS series Motor Model:NAS-Non self-priming pump Materical:PP Power:10hp Pole:2P Primary ring:Silicon Mating ring:Ceramic Rubber:EPDM Spring:SUS316 Frequency:50HZ Caliber:3"X2.5" Max.capacity:1333l/min Max.head:38.0m Weight:98.0kg
Non self-priming pump NAG series Motor Model:NAG-Non self-priming pump Materical:PP Power:5hp Pole:2P Primary ring:Silicon Mating ring:Ceramic Rubber:EPDM Spring:SUS316 Frequency:50HZ Caliber:2.5"X2" Max.capacity:800l/min Max.head:23.0m Weight:42.0kg
Non self-priming pump NAG series Motor Model:NAG-Non self-priming pump Materical:PP Power:15hp Pole:2P Primary ring:Silicon Mating ring:Ceramic Rubber:EPDM Spring:SUS316 Frequency:50HZ Caliber:4"X4" Max.capacity:1883l/min Max.head:30.5m Weight:115.0kg
Plunger Type Pumps, Hydraulically Actuated Diaphragm Type Pumps, Mechanically Actuated Diaphragm Type Pumps, Solenoid, Operated Diaphragm Dosing Pumps, Complete Skid Mounted Dosing Systems, Chemical Process Pumps, Seal free Magnetic Drive Pumps, Progressive Pumps, Y Type Strainers, Pulsation dampners, etc.
KN95 New US$ 0.455 - 2.58 / Piece 10000 Pieces Minimum Order : 3 - 30 days Product Details Model Number : KN95 Protective Mask-#5340 Brand Name : WinHealth (Future) Origin : China (mainland) Small Orders : Accepted Key Specifications/Special Features: KN95 Particulate Respirator CE FDA Certificate Over 95% effectiveness in filtering non-oil particles Product Introduction KN95 masks have over 95% effectiveness in filtering non-oil particles. For use primarily for respiratory protection against non-oil particles, such as those from sanding, sawing, grinding, sweeping, bagging, or from processing minerals, coal, iron ore, flour, and certain other substances. The inner and outer covers of KN95 masks are constructed from spunbond nonwoven fabric. Polypropylene melt-blown nonwoven is layered between the inner and outer covers. The ear loops are made of polyester elastic which is attached to the mask. The inside nosepiece is a polypropylene or PU foam. Product Specifications Product Size Specification and Appearance Requirements Product Appearance and Materials Specifications of KN95 Mask NameParameter Product name - KN95 Particulate Respirator Material - Spunbond nonwovens, melt-blown nonwovens, hot air cotton, nose clip, elastic ear loops Model - Foldable Size - 110 mm*160 mm /4.33in.*6.30in. Product application scope and purposeMainly used for respiratory protection against non-oil particles, such as those from sanding, sawing, grinding, sweeping, bagging, or from processing minerals, coal, iron ore, flour, and certain other substances. Expiration date - 3 years after production Packaging specification - 2pcs/bag; 50pcs/box; 1000pcs/Carton Usage instructions1. Hold the ear loops in both hands with the metallic strip up. 2. Put the mask against your face covering both nose and mouth. Place ear loops around both ears. 3. Adjust mask over nose and under chin. 4. Adjust the flexible strip over bridge of nose. 5. Make sure the mask fits properly, covering the nose, mouth and chin. StorageStore in a cool, dry, clean place away from fire. Store between -20â?? and 38 (-4 F and 100 F) with relative humidity below 80 % Standards KN95 mask complies with the national standard GB2626-2006 CE FDA Certificate Self-Priming, Filter-Type Mask for Respiratory Protection. This standard specifies the technical requirements, testing methods and manufacturing procedures of the mask.
ZMD -F Series Fluorine Plastic Self-priming Magnetic Pump Operating temperature:-20oC ~ 100oC Flow Capacity :3.6 m3/h ~ 60m3/h Pump Head :20 m ~ 45m Power: 1.5-18.5kw Product Summarize :ZMD-F Series Magnetic pump is application of modern magnetic theory which use of permanent magnets to achieve non-contact indirect transmission of a chemical process pump . When the outer magnets steel rotated by Electric Motor drive , then the inner magnets in rotoring assembly will be synchronous rotating and at sometime due to impeller installed on rotoring assembly, the impeller was rotated which can be pumping solution under magnetic field effect .there have an double isolation sets between inner magnetic rotoring assembly and outer magnets steel .so the liquids was Completely isolated without leakage. Pumping casing designed circulation pump shell. there is always have liquids in the pump chamber after infusion of liquid in first time. It is not need pour liquids into pump shell when running in second time it combined all the excellent with self-priming and without leakage functions . the general self-priming height can reach up to 2 < 4 meters. Advantage:Without shaft seal and driving through by magnetic coupling, which avoid leakage. Application Field : Chemical and petrochemical industries Acids & lyes Metal Pickling in automotive manufacturing Rare-earth separation Agricultural chemicals Nonferrous smelting process Dyes Pulp & Paper Electroplating industry Radio Industry Pumping Solution: Acid and caustic liquid Oxidizer corrosive liquids Difficult-to-seal liquids
Product introduction: FSR single stage single suction self-priming pump Product features: Simple structure, light and durable, is not the end of valve, less failure, convenient repair. Technical parameters: Liftï6.4-25.7m Flowï9-283m³/h Field of application: Industrial, construction, agriculture, garden, garden, pest control, irrigation, water supply and drainage using city.
Product introduction: ZW no plugging Self-priming sewage pump is in the digestion and absorption of basic features of self suction pump and water pump two series pump is developed by a new structure, highlight the characteristics of energy-saving products. Product features: The worm is reasonable design, so that the pump has good performance advantages of no pollution, congestion, winding prevention ability. Technical parameters: Lift Flow Field of application: Widely used in municipal engineering, pumping stations, construction and other industries with solid and long fibers of sludge, waste water, city sewage treatment; also suitable for biogas digesters in rural areas, farmland irrigation, water plant water supply device.
Product introduction: WZ type multistage self-priming vortex pump Product features: The pump has the advantages of small volume, light weight, strong self-priming capacity. Technical parameters: Lift22-168m Flow1.8-18m³/h Field of application: Applicable to the petroleum chemical industry, printing and dyeing industry, hotels and villas, high-rise water for boiler.
Deep Well Self-Priming Water Pump,SELF-PRIMING JET PUMPS
