Turbo Charger Casting Suppliers and Manufacturers

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

Key Features * 15W fast charging * Android iPhone Fast charging * 3 Ways charging method (Portrait / Land scape / Pad) * Intelligent F.O detection * USB C type * F.O : Foreign Object

Essential details Place of Origin: Austria Brand Name: CAST IRON SCRAP Model Number: CAST IRON SCRAP Type: Rails Scrap Fe Content: 99 Weight: 50 Fe Content (%): 99 Product name: CAST IRON SCRAP Name: High Grade Cast Iron Scrap Packing: Bulk - Bagged Characteristics: Oil Drain Valve Mechanism Cast Iron Scrap: Iron Electric Motor Scrap Shape: Irregularity Size of Slag: 10-50mm Cut Size: 0.5 Meters Supply Ability Supply Ability 500000 Ton/Tons per Week Packaging & delivery Packaging Details As buyers request Lead time: Quantity(tons) 1 - 500 >500 Lead time (days) 14 To be negotiated

Cast Iron Scrap Cast Iron Scrap for sale. Free from mud, dust, fluff, non ferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges, other arms and ammunitions used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings, any organic waste and any other harmful substances. Dirt, dust rust, fluff and other impurities not allowed over 1%. Chemical Composition: C:0.06 0.082% Mn:0.75 1.05% SI:0.13 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15%

Clean cast iron scrap such as columns, pipes, plates,and castings of a miscellaneous nature, including automobiles. Our company is a leading exporter of ferrous and nonferrous metals. We export industrial scrap metal and obsolete scrap metal and supplies the recycled metals to its customers, including integrated steel mills, foundries, secondary smelters, and metals brokers. In ferrous we mainly deal in HMS1 & 2 Material Specification Heavy Melting Scrap (HMS 1& 2) ,80% HMS 1 & 20 % HMS 2 confirming to ISRI 200-206 Steel scraps shall be totally free from any types of radiation, bombs, arms and ammunition, mines, shell, cartridges, sealed containers, gas cylinders, explosive shells or explosive materials in any form either used or otherwise as per the specification below. HMS 1 ISRI Code 200: heavy melting steel. Wrought iron and/or Steel scrap 1/4 inch or steel scrap inch and over in thickness. Individual pieces not over 60 x 24 inches HMS 1 ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap HMS 1 ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap HMS 2 ISRI Code 203: heavy melting steel. Wrought iron or Steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 ISRI Code 204: same as ISRI 203 but max size 36x18 inches. HMS 2 ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material. HMS 2 ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches

Cast Iron Scrap for sale. Free from mud, dust, fluff, non ferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges, other arms and ammunitions used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings, any organic waste and any other harmful substances. Dirt, dust rust, fluff and other impurities not allowed over 1%. Chemical Composition: C:0.06 0.082% Mn:0.75 1.05% SI:0.13 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% C 0.06 0.082% Mn 0.75 1.05% SI 0.13 0.28% P Max 0.035% S Max 0.045% HMS 1 ISRI Code 200: heavy melting steel. Wrought iron and/or Steel scrap 1/4 inch or steel scrap 1/4 inch and over in thickness. Individual pieces not over 60 x 24 inches HMS 1 ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap HMS 1 ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap HMS 2 ISRI Code 203: heavy melting steel. Wrought iron or Steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 inches. HMS 2 ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material.HMS 2 ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches

Product Brands: ABC, ABC Alkaline. Available Variants: AAA, AA, C, D, 9V Product of Indonesia

Key Features * 15W fast charging * Android iPhone Fast charging * 3 Ways charging method (Portrait / Land scape / Pad) * Intelligent F.O detection * USB C type

Duracell Batteries

This Cast Iron slag is a by-product derived from the production of thermal insulating products. The byproduct is a ferrous slag which can be utilised in an electric arc furnace to produce crude steel. Physical Description On visual inspection, it appears to be made up of irregular shapes. Dimension: 500mm -800mm Chemical Composition Its chemical composition is homogeneous and stable with Fe contents in the range of 90 +/- 5% and P contents < 0.6% S around 0.15% and C% around 3.5%. Packing: Loose in container Loading: in 20 Container For further information, please feel free to contact us.

Function QC2.0 Maximum Output Power 18W Place of Origin Guangdong, China Usage Mobile Phone Material ABS Protection Overcurrent Private Mold NO Model Number DS2018 Input voltage and current 12v/4a output voltage and current 5V/4.5A Item 4.8A Dual USB Port Socket Charger Rocker Style, color BLUE,, RED Certificate CE FCC ROHS voltage 12-24V Material ABS+Nylon Application car ,boat samples free for 1 pc market range usa, australia, japan, eupora