A. Specification Product Quality Stainless Steel Wool fill fabric for home Material Stainless steel and poly fiber WeightRanging from 2000gsm Size4"*10m per roll or as requested Width 47"/48" PackageRoll or Sheet B. Feature: 1. 100% non-toxic and environmentally safe 2. Easy to install due to its flexible, compressible nature, comes in rolls and can be cut to size or shape desired, stuff it in the hole, and your have done. 3. It is a permanent solution, will not rust or corrode over time, dose not shrink, stain, pull out. 4. Made of sharp durable fibers material which is suitable to die cut to specific shapes and sizes. 5.Most consistent material for exhaust applications with strength in all directions as cross-lapped material going at approximately 90 degree angles to other fibers. 6. Installs under landscaping and allows grass and small plants to grow through, thus being an invisible force against pests. C. Function 1. Fill fabric is an exclusion fabric used by professional nuisance control and pest control operators. 2. It is composed of stainless steel and poly fibers. This blend of materials gives it an extra â??spring backâ?�, allowing for easier fitting in crevices and the ability to stay in place well. Cut it 2-3 times the size of the opening to make a tight fit. 3. It is highly resilient and is an impenetrable barrier against rodents and pests. D. Application Burrowing animals such as rats, chipmunks, gophers, groundhogs and nutria can dig beneath the ground and ruin landscaping, chew through cables and destroy dikes and levees. Prevent these animals from wreaking havoc beneath the ground, currently protecting many public and private sites. E. Install Instructions 1. Install it by pressing it into rodent-prone crevices with gloved hands or simple tools like a putty knife or screwdriver. 2. Do not install it close to live electrical conductors, since stainless stell is an electrical conductor. Installing IT around fully sealed electrical conduit coming out of a wall is safe.
A):Specification: Product Steel Wool Prices Suppliers and Manufacturers at Alibaba.com Material Stainless steel and poly fiber Weight Ranging from 2000gsm Size 4"*10m per roll or as requested Width 47"/48" Package Roll or Sheet B):Feature: 1. 100% non-toxic and environmentally safe 2. Easy to install due to its flexible, compressible nature, comes in rolls and can be cut to size or shape desired, stuff it in the hole, and youâ??re done. 3. It is a permanent solution, will not rust or corrode over time, dose not shrink, stain, pull out. 4. Made of sharp durable fibers material which is suitable to die cut to specific shapes and sizes. 5.Most consistent material for exhaust applications with strength in all directions as cross-lapped material going at approximately 90 degree angles to other fibers. 6. Installs under landscaping and allows grass and small plants to grow through, thus being an invisible force against pests. C):Function: 1. Fill fabric is an exclusion fabric used by professional nuisance control and pest control operators. 2. It is composed of stainless steel and poly fibers. This blend of materials gives it an extra â??spring backâ?�, allowing for easier fitting in crevices and the ability to stay in place well. Cut it 2-3 times the size of the opening to make a tight fit. 3. It is highly resilient and is an impenetrable barrier against rodents and pests. D):Application Burrowing animals such as rats, chipmunks, gophers, groundhogs and nutria can dig beneath the ground and ruin landscaping, chew through cables and destroy dikes and levees. Prevent these animals from wreaking havoc beneath the ground, currently protecting many public and private sites including: Tree pits Shopping mall landscapes Planters Parks Sports fields River and canal banks Retention ponds National historic sites Outdoor amphitheatres E):Install Instructions 1. Install it by pressing it into rodent-prone crevices with gloved hands or simple tools like a putty knife or screwdriver. 2. Do not install it close to live electrical conductors, since stainless stell is an electrical conductor. Installing IT around fully sealed electrical conduit coming out of a wall is safe.
AISI302, 304,316,316L,310S,410,430,904L,2205,2507,etc 2.Wire Diameter: 0.015-2.8mm 3.Mesh count: Plain weave can be woven up to 400 mesh. Twill weave can be woven from 400 to 635mesh. Dutch weave can be woven up to 3500mesh
Filter Rating: 90% Length: 30m Width: 0.02-5m Features: Corrosion resistance. Anti-acid and alkali. Anti-high temperture. Good filter performance. Long using life
Duplex 2205 is a nitrogen-enhanced duplex stainless steel that was developed to combat common corrosion problems encountered with the 300 series stainless steels. Duplex ? describes a family of stainless steels that are neither fully austenitic, like 304 stainless, nor purely ferritic, like 430 stainless. The structure of 2205 duplex stainless steel consists of austenite pools surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. Often referred to as the work horse grade, 2205 is the most widely used grade in the duplex family of stainless steels The advantage of a duplex structure is that it combines the favorable qualities of a ferritic alloy (stress corrosion cracking resistance and high strength) with those of an austenitic alloy (ease of fabrication and corrosion resistance). Usage of 2205 Duplex stainless steel should be limited to temperatures below 600 F. Extended elevated temperature exposure can embrittle 2205 stainless.
Duplex 2507 is a super duplex stainless steel designed for applications which demand exceptional strength and corrosion resistance. Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking. Usage of Duplex 2507 should be limited to applications below 600�?�° F (316�?�° C). Extended elevated temperature exposure can reduce both the toughness and corrosion resistance of alloy 2507. Duplex 2507 possesses excellent mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy. The resulting savings in weight can dramatically reduce the overall cost of fabrication. The advantage of a duplex structure is that it combines the favorable qualities of a ferritic alloy (stress corrosion cracking resistance and high strength) with those of an austenitic alloy (ease of fabrication and corrosion resistance). Usage of 2205 Duplex stainless steel should be limited to temperatures below 600 F. Extended elevated temperature exposure can embrittle 2205 stainless
310S stainless steel is a highly alloyed austenitic stainless steel that is designed for use in high-temperature applications. It contains a high percentage of chromium and nickel, as well as a low amount of carbon, which gives it excellent resistance to oxidation, sulfidation, and other forms of high-temperature corrosion. Some of the key properties of 310S stainless steel include: High-temperature resistance: 310S can withstand high temperatures up to 1150�°C (2102�°F) without losing its strength or corrosion resistance properties, making it ideal for use in applications such as furnace parts, heat exchangers, and kilns. Corrosion resistance: 310S offers excellent resistance to oxidation, sulfidation, and other forms of high-temperature corrosion, as well as resistance to aqueous corrosion. Strength and toughness: 310S has good strength and toughness, making it suitable for use in demanding applications. Fabricability: 310S is easily formable using standard methods, and can be welded using common welding techniques. 310S stainless steel is commonly used in a range of high-temperature applications, including: Furnace parts, such as burners, heating elements, and retorts Heat exchangers and boilers Kilns and other high-temperature processing equipment Chemical processing equipment Power generation equipment, such as gas turbines and exhaust systems Overall, 310S stainless steel is a highly versatile and reliable material that is well-suited for use in a range of high-temperature applications where superior corrosion resistance and strength are required. The following are some of the commonly used international standards for 310S stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10095: Heat resisting steels and nickel alloys JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:310S stainless steel coil; 310S stainless stee strip;310S stainless stee plate; 310S stainless steel sheets; 310S stainless steel tubes; 310S stainless steel pipe; 310S stainless steel flat; 310S stainless steel bar
321 stainless steel is an austenitic stainless steel that contains titanium as a stabilizing element. This element helps to prevent chromium carbide precipitation, which can occur during high-temperature service, making it ideal for use in high-temperature applications. Some of the key properties of 321 stainless steel include: High-temperature resistance: 321 can withstand high temperatures up to 870�°C (1600�°F) without losing its strength or corrosion resistance properties, making it ideal for use in applications such as furnace parts and exhaust systems. Corrosion resistance: 321 offers excellent resistance to corrosion, including aqueous corrosion and stress corrosion cracking. Strength and toughness: 321 has good strength and toughness, making it suitable for use in demanding applications. Fabricability: 321 is easily formable using standard methods, and can be welded using common welding techniques. Some of the common applications for 321 stainless steel include: Exhaust systems in automobiles, aircraft, and industrial equipment High-temperature furnace parts, such as burners and heating elements Chemical processing equipment Jet engine parts Heat exchangers Overall, 321 stainless steel is a highly reliable and versatile material that is well-suited for use in high-temperature applications where superior corrosion resistance and strength are required. The following are some of the commonly used international standards for 321 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10095: Heat resisting steels and nickel alloys JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:321 stainless steel coil; 321 stainless stee strip;321 stainless stee plate; 321 stainless steel sheets; 321 stainless steel tubes; 321 stainless steel pipe; 321 stainless steel flat; 321 stainless steel bar Applied to open-air machines, heat-resistant parts of building materials and parts with difficulty in heat treatment in chemical, coal and petroleum industries that require high resistance to intergranular corrosion 1. Petroleum waste gas combustion pipeline 2. Engine exhaust pipe 3. Boiler shell, heat exchanger, heating furnace parts 4. Silencer parts for diesel engines 5. Boiler pressure vessel 6. Chemical transport vehicle 7. Expansion joints 8. Spiral welded pipes for furnace pipes and dryers
347 stainless steel is a stabilized austenitic stainless steel that contains niobium, which helps to prevent intergranular corrosion that can occur during welding and exposure to high temperatures. It is often used in high-temperature applications due to its excellent resistance to oxidation and its ability to withstand high temperatures without losing its strength or corrosion resistance properties. Some of the key properties of 347 stainless steel include: High-temperature resistance: 347 can withstand high temperatures up to 870�°C (1600�°F) without losing its strength or corrosion resistance properties, making it ideal for use in high-temperature applications such as furnace parts and exhaust systems. Corrosion resistance: 347 offers excellent resistance to corrosion, including aqueous corrosion and stress corrosion cracking. Weldability: 347 is easily weldable using common welding techniques, and the addition of niobium helps to prevent intergranular corrosion that can occur during welding. Strength and toughness: 347 has good strength and toughness, making it suitable for use in demanding applications. Some of the common applications for 347 stainless steel include: High-temperature furnace parts, such as burners and heating elements Exhaust systems in automobiles, aircraft, and industrial equipment Chemical processing equipment Jet engine parts Heat exchangers Overall, 347 stainless steel is a highly reliable and versatile material that is well-suited for use in high-temperature applications where superior corrosion resistance and strength are required, and where welding is required. The following are some of the commonly used international standards for 347 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10095: Heat resisting steels and nickel alloys JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:347 stainless steel coil; 347 stainless stee strip;347 stainless stee plate; 347 stainless steel sheets; 347 stainless steel tubes; 347 stainless steel pipe; 347 stainless steel flat; 347 stainless steel bar Widely used in boiler, power generation, petroleum, chemical, synthetic fiber, food, paper and other industries. Heat exchangers for large boiler superheater tubes, reheater tubes, steam piping and petrochemical.
420 stainless steel is a kind of martensitic stainless steel, which has the characteristics of certain wear resistance and corrosion resistance, and high hardness. 420 stainless steel is a martensitic grade of stainless steel that contains chromium and molybdenum, making it corrosion-resistant and hardenable. It has good strength, hardness, and wear resistance, and is commonly used in applications where high strength and moderate corrosion resistance are required, such as in cutlery, surgical instruments, and dental equipment. Some of the key properties of 420 stainless steel include: Corrosion resistance: 420 has good corrosion resistance in mild atmospheric environments and in most mild chemical environments. Hardness: 420 is a hardenable stainless steel and can be hardened by heat treatment, making it ideal for applications where high hardness is required. Wear resistance: 420 has good wear resistance due to its high hardness. Machinability: 420 has moderate machinability in the annealed condition, but is more difficult to machine in the hardened condition. Some of the common applications for 420 stainless steel include: Cutlery, including knives, scissors, and blades Surgical instruments, such as scalpels and forceps Dental equipment, including dental drills and hand tools Valve parts Pump shafts and bearings Overall, 420 stainless steel is a reliable and versatile material that is well-suited for use in applications where high strength, hardness, and moderate corrosion resistance are required. Here are some of the most common international standards for 420 stainless steel: ASTM A276: Standard Specification for Stainless Steel Bars and Shapes ASTM A314: Standard Specification for Stainless Steel Billets and Bars for Forging ASTM A473: Standard Specification for Stainless Steel Forgings ASTM A580: Standard Specification for Stainless Steel Wire EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes JIS G4303: Stainless steel bars GB/T 1220: Stainless steel bars We can provide the following form:420 stainless steel coil; 420 stainless stee strip;420 stainless stee plate; 420 stainless steel sheets; 420 stainless steel tubes; 420 stainless steel pipe; 420 stainless steel flat; 420 stainless steel bar 420 stainless steel is suitable for all kinds of precision machinery, bearings, electrical appliances, equipment, instruments, meters, transportation tools, household appliances, etc. It is mostly used in the manufacture of parts resistant to atmosphere, water vapor, water and oxidative acid corrosion.
434 stainless steel is a type of ferritic stainless steel that contains a higher amount of molybdenum compared to 430 stainless steel. This addition of molybdenum improves its corrosion resistance and makes it more resistant to pitting and crevice corrosion, especially in chloride-containing environments. It also offers good resistance to high-temperature oxidation and scaling. Here are some key properties of 434 stainless steel: Corrosion resistance: 434 stainless steel offers good resistance to corrosion, especially in chloride-containing environments. Heat resistance: 434 can withstand high temperatures without losing its strength or corrosion resistance properties. Its high chromium content provides excellent resistance to scaling and oxidation up to 815�°C (1500�°F). Weldability: 434 stainless steel can be welded using common welding techniques. Machinability: 434 is not as machinable as some other stainless steels, such as 304, due to its high hardness and low ductility. Magnetic properties: 434 stainless steel is a magnetic material. Overall, 434 stainless steel is a corrosion-resistant and heat-resistant material that is well-suited for use in high-temperature and chloride-containing environments. Its higher molybdenum content provides superior corrosion resistance compared to other ferritic stainless steels, making it a popular choice in applications such as automotive exhaust systems and chemical processing equipment. Here are some of the most common international standards for 434 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A268/A268M: Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service ASTM A554: Standard Specification for Welded Stainless Steel Mechanical Tubing EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip Application fields: Automotive exhaust systems and mufflers. Heat exchangers and furnaces. Chemical processing equipment. Industrial drying ovens. Kitchen utensils and appliances. We can provide the following of the form:434 stainless steel coil; 434 stainless stee strip;434 stainless stee plate; 434 stainless steel sheets; 434 stainless steel tubes; 434 stainless steel pipe;434 stainless steel flat; 434 stainless steel bar
444 stainless steel is a low-carbon, dual-stabilized ferritic stainless steel that is highly resistant to corrosion, especially in chloride environments. It is often used in applications where high corrosion resistance and good formability are required. Some of the key properties of 444 stainless steel include: Corrosion resistance: 444 stainless steel has excellent resistance to corrosion, especially in chloride environments such as seawater, brackish water, and chloride-containing acids and solvents. Heat resistance: It can withstand high temperatures up to 950�°C (1742�°F) without losing its strength or corrosion resistance properties. Formability: It has good formability and can be easily fabricated into various shapes and sizes. Weldability: It can be welded using common welding techniques, and does not require preheating or post-weld heat treatment. Cost-effective: Compared to other stainless steels, 444 stainless steel is a cost-effective option due to its lower nickel content. Some of the common applications for 444 stainless steel include: Automotive exhaust systems: It is often used in the manufacture of automotive exhaust systems due to its excellent corrosion resistance and heat resistance. Industrial equipment: It is also used in various industrial equipment such as heat exchangers, tanks, and piping systems. Kitchen appliances: It is used in the manufacture of kitchen appliances such as refrigerators, dishwashers, and ovens due to its good formability and corrosion resistance. Overall, 444 stainless steel is a highly versatile and cost-effective material that is ideal for use in corrosive environments where high corrosion resistance and good formability are required. Here are some of the most common international standards for 444 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A268/A268M: Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service ASTM A554: Standard Specification for Welded Stainless Steel Mechanical Tubing EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following of the form:444 stainless steel coil; 444 stainless stee strip;444 stainless stee plate; 444 stainless steel sheets; 444 stainless steel tubes; 444 stainless steel pipe;444 stainless steel flat; 444 stainless steel bar 444 stainless steel is generally used to manufacture stress corrosion resistant equipment, video machinery, automotive engine exhaust pipe storage tanks, solar water heaters, printing and dyeing machinery, heat exchangers, etc.
2205 stainless steel, also known as duplex stainless steel, is a type of stainless steel that is characterized by its two-phase microstructure consisting of both austenitic and ferritic phases. This combination of phases provides the alloy with improved strength and corrosion resistance compared to standard austenitic stainless steels. Some of the key properties of 2205 stainless steel include: High strength: 2205 stainless steel has excellent strength properties, making it suitable for use in demanding applications such as structural components and pressure vessels. Corrosion resistance: 2205 stainless steel provides good corrosion resistance in a variety of environments, including chloride-containing and acidic environments. Weldability: 2205 stainless steel is easily weldable using common welding techniques and does not require preheating or post-weld heat treatment. Fatigue resistance: 2205 stainless steel has good fatigue resistance, which makes it suitable for use in applications where cyclic loading is present. High toughness: 2205 stainless steel exhibits high toughness even at low temperatures, making it suitable for use in cryogenic applications. Overall, 2205 stainless steel is a highly versatile material that offers excellent strength and corrosion resistance properties, making it ideal for use in a wide range of demanding applications. Here are some of the most common international standards for 2205 duplex stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A789/A789M: Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service ASTM A790/A790M: Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10216-5: Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes NACE MR0175: Sulfide stress cracking-resistant metallic materials for oilfield equipment NORSOK MDS D45: Qualification of manufacturers of duplex stainless steels UNS S31803/S32205: Unified numbering system designations for duplex stainless steels We can provide the following form:2205 stainless steel coil; 2205 stainless stee strip;2205 stainless stee plate; 2205stainless steel sheets; 2205 stainless steel tubes; 2205stainless steel pipe;2205 stainless steel flat; 2205 stainless steel bar
I-Beam Steel I-Beams, also known as H-Beam, are one of the most common steel profile used in construction and civil engineering. It provide support for buildings and load-bearing walls. The I-shaped section optimises strength weight ratio & surface usability to provide a highly efficient product. It is right-angle formed & so has high bending resistance, construction application simplicity. It save cost, is light weight and thus is used widely in various industries.
T-Beam: A T-Beam is a load-bearing structure with a t-shaped cross section. The top of the t-shaped cross section serves as a flange or compression member in resisting compressive stresses. The web of the beam below the compression flange serves to resist shear stress and to provide greater separation for the coupled forces of bending. Other uses for one way to make a T-beam to be more efficient structurally is to use an inverted T-beam with a floor slab or bridge deck joining the tops of the beams. Done properly, the slab acts as the compression flange.
Angle Bar Angle steel bars are perpendicular elongated steel bars connected together as a wave-like product. There are equal angles and unequal angles. Angle steel bar is a simple sectioned carbon structural steel mostly used in metal products fabrication and construction of workshop. In application, it must has weldability, plasticity deformation performance and high mechanical strength. The raw material to produce angle steel is low-carbon billet. Finished product of angle steel is hot roll formed.
Square Tubes: Structural Tubes, also known as hollow sections, are used as a structural element in buildings, bridges and other structures, and in a wide variety of manufactured products. It’s produced in round, square and rectangular shapes in a broad range of sizes and gauges. Square Tube, similar to round tube, has efficient shape for multiple-axis loading as it has uniform geometry along two or more cross-sectional axes, and thus uniform strength characteristics. This makes it good choice for columns. It also has excellent resistance to torsion.
Rebar Bars: The rebar, also known as deformed bar, is a steel bar or mesh of steel wires used as a tension device in reinforced concrete and reinforced structures to strengthen and hold the concrete in tension. Rebar’s surface is often patterned to form a better bond with the concrete.
Steel Plates: Steel plates are often used for structural and construction applications, pressure vessels, marine and offshore equipment, and military applications. It can be used anywhere where a connection between 2 beams is required. They are used for base plates, end plates, stiffeners, gussets, tabs, splice plates and many more. In some cases they add strength to a beam when welded along the length of a beam (top or bottom).
