feature Sturdy Design, Stable Performance Voltage 440 V Automatic Grade Semi Automatic Power 750 W Driven Type Electric
Material Stainless Steel Operating Mode Automatic Phase Single Phase Shape Rectangular Voltage 220V Machine Material Stainless Steel Driven Type Electric Finishing Polished Rated Power 1-3 KW
Shaft-less screw conveyor is a fairly recent development in screw conveyor design and is growing in popularity because it is the perfect solution for many bulk solids handling applications. The shaft-less screw conveyor is the solution for conveying many difficult bulk solids. In fact, the shaft-less conveyor was so successful in the Environmental industry, that its use has been promoted in many other industries such as chemical, food, and minerals processing. Shaft-less screw conveyor application: It is widely used in building material, metallurgy, chemical industry, electric power, coal, machinery, light industry, food and food industry, suitable for conveying powder, granule, small block material, such as cement, coal, food, chemical fertilizer, ash, sand, coke, etc. Structure A shaft-less conveyor is designed to be supported by a liner that conforms to the radius of the trough. The weight of the shaft-less spiral is distributed over the full length of the spiral on the liner. The drive is connected to one end of the spiral by means of a flanged and bolted drive shaft and spiral end plate, while the tail end of the spiral is not connected and is allowed to rotate freely. If your process consists of bulk solids with high moisture content, then the shaft-less screw conveyor is a perfect solution. OUR ADVANTAGE 1. Strong anti-winding, no central axis interference. It has obvious advantages for conveying the sticky material, easy winding material. 2. Good environmental performance. It adopts fully enclosed spiral surface, which can ensure that environmental hygiene and transportation of materials from pollution, no leakage. 3. Large torque, low energy consumption. As the spiral without shaft, the material is not easy to plug, the discharge port is not blocked, which can be lower speed operation, smooth transmission, reduce energy consumption. The torque can be 4000N / m. 4. Large conveying capacity. The capacity is 1.5 times as the traditional shaft screw conveyor with the same diameter. Long conveying distance and ultra-long distance transport materials. The conveying length can reach 30 meters, which also can be adjusted according to user needs and installed by multi-level series.
organization structure Shaftless screw conveyor is mainly composed of driving device, head assembly, casing, shaftless screw body, groove lining plate, feed inlet, discharge outlet, machine cover (when required), base, etc. Driving device: cycloidal pin gear reducer or shaft mounted hard tooth gear reducer shall be adopted. In the design, the driving device shall be set at the end of the discharge port as far as possible to make the spiral body in the tension state during operation. The head is equipped with thrust bearing, which can bear the axial force generated when conveying materials. Casing: the casing is U-shaped or O-shaped, with a rain proof cover on the upper part, which is made of stainless steel, carbon steel or FRP. Shaftless spiral body: made of stainless steel or carbon steel. Tank lining plate: the material is wear-resistant plastic plate, rubber plate or cast stone plate. Inlet and outlet: there are two types: square and circular. Generally, the form of inlet and outlet is determined by the user. Scope of application Screw conveyor has the advantages of simple structure, low manufacturing cost, strong sealing, safe and convenient operation, and can be loaded and unloaded at multiple points in the middle It is widely used in chemical industry, building materials, metallurgy, grain and other departments < Under the condition of 20 , transport powdery, granular and small pieces of materials with low viscosity, not easy to deteriorate and caking
stainless steel screw conveyor for powder Product introduction Screw conveyor is an efficiency transportation equipment with power device, gear box, coupling, screw shaft, hanger bearing and support base. Screw shaft is made of several sections which connected with spline. With this special design, it can bear large load capacity and easy to dismounting. Screw conveyor is special used for cement plant or transport powder in field working. It is applicable for transporting powder granular and small blocked bulk material, such as clay powder, cement, concrete, sand, stone, grain, coal etc. Also can complete the gathering, stirring, mixing, dehydrating, customizing material, unloading, stacking during conveyor. Screw Conveyor Advantages 1.Adopt high-quality steel pipe with good integral rigidity. 2.Adopt universal ball joint, which facilitates installation, adjustment and steering. 3.Adopt standard parts and components, which makes it is convenient for transportation. 4.Adopt high-quality reducer with heavy-duty design, large torque and low noise. 5.Adopt high-quality middle-hoisting bearing and tail bearing. Working principle When the hollow axes with screw flight rotate along the jacketed trough, the bulk material feed into the trough and screw flight was hold of trough during running, the screw flight push the material and make the material do axial movement, simultaneity the material contact with the hollow shaft and jacketed trough full with cooling water and do heat transfer process. The cooled material can be discharged at the proper outlet at the bottom of trough or transport our at the end of trough. Application Screw conveyor is widely used in various industries, such as building materials, chemicals, electric power, metallurgy, coal, grain and other industries, for horizontal or inclined conveyor dust, granular materials and small block, such as coal, ash, slag, cement, food, etc. The material temperature is less than 200 degree centigrade. It is not suitable for conveying perishable, viscous, easy caking materials. Specifications: model LS100-800 distance of blades 100mm -500mm diameter 100mm -800mm (rpm) 40-140 (t/m3) 2.2-198.5
Stainless Automatic Screw Conveyor, Screw Feeder Machine, Feeding Machine for Powder,carbon Steel / Stainless Steel Conveyor Hopper Feeder machine Product Description: KSJ type screw feeder machine,screw conveyor is my company combining the domestic and foreign various screw conveyor experience, design and research and development of products, the products can meet the requirement of mixing plant (floor) batching scale, the products are sold all over the country, equipped with various mixing machine, and exported to foreign countries. Stainless Steel Screw Feeder Machine can convey kinds of materials. Combined with the package-machine of our company, it can do material situation tracing. Also can be used separately. Complete machine made in stainless steel, except for the electrical machine, gearing, and the framework.Material is through screw pole's to drop into the Hopper. 1.KSJ type screw conveyor,feeder machine, belongs to non basic formula , it is controlled by a speed reducing motor device and casing ,spiral assembly arranged side, combined into a complete set of equipment, movement and installation is very convenient. 2 screw assembly and shaft end use of spline connection, convenient loading and disassembly, carrying capacity, good for neutral, safe and reliable. 3. Good sealing performance, shell production and production of seamless steel tubes, each end connecting through a flange machine without dust leakage, neither the waste material, in order to create a good working environment, in line with the requirements of environmental protection. 4 small sizes, high speed, variable pitch, ensure the fast even delivery. 5 feed inlet can be according to the work site situation made from the angle of inclination, and can use flange connection, bag connection and universal joints flange connection, users can choose according to need. Characteristics: screw feeder machine is composed of double motor, feeding motor, vibrating motor and each switch control. Hopper is adjustable and vibrational which make material to be flowing easily. It is good to material. Hopper is separate from twisting shaft. Structure is reasonable and easily loading and unloading Characteristic dustproof, bearing won't be polluted by the dust and powder. To cleanup scrapped materials conveniently and design the machine to be: Discharging the material reversally, storing materials at the bottom of hopper pipe, taking out the whole screw. 1: Unique design, good looking 2: Small size, with wheel, easy to move 3: Screw- type design, automatic, low energy consumption, labor saving 4: Easy to operate and clean 5: Stable performance
Screw Conveyors Precision sheet metal fabrication in M.S & S.S.For textile texturising machines, industrial machines, screw conveyors for material handling ovens and dryr\ers for baking purpose
Model:LS200-LS500 Conveying Capacity:7-90ï¼?m³/hï¼? Conveying Distance:2-25ï¼?mï¼? Application:coal, slag, cement, grain Screw conveyor is a kind of continuous conveying equipment without flexible traction mechanism. It mainly used to convey powder, granular and small lump material which is less viscous and hard blocking, such as coal, slag, cement, grain and etc. It can be widely used in building materials, chemicals, power, metallurgy, coal and other industries. Screw conveyor generally used for continuity conveying bulk materials in short distance at horizontal or slightly oblique (angle βâ?¤15 °) direction. It can mix and stir the material during conveying. The working environment is -20 ~ 50 â??, and the material should be less than 200 â??. Its design and fabrication meet the professional standards in JB/T7679-2008-"screw conveyor". The hanging bearing adopts the two structures of rolling and sliding interchangeable. It has low resistance, strong sealing and good wear resistance. OUR ADVANTAGE 1 It achieved clean and environmentally friendly production, especially suitable for conveying dusty, hot (under 200 â??) and sharp odour material. 2 The wear treated screw is more wearable and stronger than traditional common screw. It can significantly increase the service life of the screw 3 It can achieve multi-point feeding and multi-point discharging according to user's process layout. 4 The redesigned discharging structure makes the discharging smoother. 5 Compact structure, less wearing parts, convenient to install, operate and maintain. LS series screw conveyor is mainly composed by screw, chute, hanging bearings, driver, supports, inlet and outlet. The main structural characteristics of each part are: 1.The head and tail bearing are arranged outside the chute. It avoids dust entering the bearing and convenient to install and maintain; 2.The optimized screw solved the material blocking problem at the outlet; 3.The screw shaft use reducing structure. It increases the volume at hanging bearings to reduce the wearing by the friction between bearing and material; 4.The screw shaft and hanging bearing connection applies embedded structure. There's no axial movement during mount and dismount. Thus it is convenience to maintain and repair; 5.The hanging bearing structure is compact and the dimension of axial and radial dimensions is small. It can avoid the material stuck and blocking; 6.The hanging bearing has improved sealing and lubricating structure. It help the bearing protection and lubrication effectively and can significantly increase its service life; 7.The hanging bearing is fixed at screw shaft connections of each segment. It can ensure the concentricity of the screw shaft while increasing its overall stiffness.
A helical conveyor or drill conveyor is a mechanism that utilizes a rotating helical screw weapon, normally within a device, to transfer fluid or granular elements stuff. All are done in various bulk treatment applications. Screw conveyors in recent manufacturing industries are often used horizontally or at an inadequate approach as an effective way to drive semi-solid elements stuff.
The spiral conveyor is divided into two kinds: axial screw conveyor and non-axial screw conveyor, which are divided into u-type screw conveyor and tube type screw conveyor. The axial screw conveyor is suitable for non-stick dry powder materials; And no axial screw conveyor suitable for sticky and easy winding materials. Working principle: When the screw axis rotation, due to the gravity of the material and the tank wall solutions generated by friction, make the material only under the push of blade groove bottom along the conveyor moving forward, the situation can't seem to rotate the nut along the rotation of the screw for translational motion. The movement of the material in the middle bearing is the thrust of the material that is moving forward. Therefore, the transport of materials in the conveyor is completely a sliding motion. In order to keep the spiral shaft in a favorable tensile condition, the driving device and unloading port are generally placed on the same end of the conveyor, while the feeding mouth is placed near the rear end of the other end. The rotating spiral blade is transported by the material, so that the force of the material not rotating with the blade of the spiral conveyor is the friction resistance of the material's weight and the screw conveyor casing to the material. The face type of the blade has the type of solid surface, belt type, blade face type according to the different conveying materials. The spiral shaft of the screw conveyor has a thrust bearing at the end of the material movement direction to the axial force of the screw with the material. When the captain is longer, he should hang the bearing in the middle.
Brief description The equipment has the characteristics of low speed, high conveying efficiency, step-less speed regulation, low energy consumption and so on. It can ensure that the material is conveyed to paste pump at a certain pressure. Application This equipment is based on a bi-axial spiral rectangular structure and is widely used in the treatment of paste materials such as slime, sludge, calcium carbide sludge, printing and dyeing sludge, etc. It is a part of the paste material pumping system. After stirring and conveying, the materials are conveyed to the KOS series paste pump through the bottom discharge port under the stirring of the twin-shaft coupled spiral blades. Effectively solve the problems of material compaction and uneven mixing. It greatly improves the transfer efficiency of paste and viscous materials, and reduces the unit time cost.
The development of screw conveyor is divided into two types: axial screw conveyor and shaftless screw conveyor [1]. The axial screw conveyor is composed of screw, U-shaped chute, cover plate, inlet and outlet and driving device. Generally, there are three types: horizontal type, inclined type and vertical type; The shaftless screw conveyor is changed from screw to shaftless screw, and a replaceable lining body is installed in the U-shaped groove. The structure is simple. The materials are input from the feed port and output from the discharge port after being pushed by the screw. The whole transmission process can be carried out in a sealed groove. Generally speaking, the screw conveyor we usually refer to refers to the screw conveyor with shaft type.
Type Inclined Material Stainless Steel Phase Three Phase Shape Rectangular Voltage 220V Driven Type Electric Loading Capacity 5-10 Kg Usage Moving Goods
LS type screw conveyor is the updated product of GX type screw conveyor. It is designed according to standard of JB/T67995 screw conveyor. The machine has high reliability, long lifetime, good applicability, convenience to install and maintain. Standard export package or as per customers' requirements.
HY-S1 Screw conveyor feeder for powder and granule,spiral conveyor Technical parameter: Feeding way¡êoSpiral feeding Feeding motor:Stepper motor Transmission mechanism: Reducer Packaging specifications: 2-3000g (interchangeable screw adjusting) Feeding speed:1000KG-3OOOKG/h(can be customized) Machine body meterial: 202# stainless steel (optional 304#) Number of spiral pipe section: 3 Length of feeding pipe:2200mm((can be customized)) Conveyor height:1600mm(can be customized) Machine weight:150kg Machine Power:1.5kw
1.Description of Stainless Steel Shaftless Screw Conveyor Screw conveyor Material: Stainless steel or carbon steel 2.Application Area of screw conveyor: 2.Screw conveyor Usage:transport many kinds of material,such as convey flour, grain, cement, chemical fertilizer, lime-ash, sand, pebble, coal powder etc. but it can't be used to transport material of easy metamorphous, high stickiness and easy blocking. 3..Main Features of screw conveyor: A. Large bearing capacity, safe and reliable. B. Strong adaptability, easy installation and maintenance, long service life. C. The machine is small in size, high speed, ensure rapid and uniform delivery D. The discharging end is equipped with cleaning device. It has low noise, strong adaptability, flexible to in and out of the mouth E. Sealing good and the shell is made of seamless steel tube, the end uses flange to connect each other into an organic whole.
Screw Conveyor Screw conveyor is designed to delivery drilling cuttings and feed to vertical cuttings dryer or High G dryer for further treatment Usually, the screw diameter has 4 options : 10 inch, 12inch, 16 inch, 20 inch; screw length is customer built too, but commonly there are 12~48feet Furthermore, depends on clients' demand the screw conveyor will be made of different materials Including carbon steel, stainless steel graded differently Description Screw conveyor is also referred to Auger feeder. They can be used as the transfer unit of drilling cuttings to cuttings dryer, also the unit to transfer disposal to cuttings tank or collection container. The length can be custom built according to actual working condition
Screw
Screw
CWP Machinery manufactures spiral conveyors in various diameter, various length, and various types according to the purpose from carbon steel or stainless steel materials. Chain Conveyors It is used for the high capacity transport of the granule materials in narrow space, in short or long distance. It usually operates in the galleries of the underground mining firms. It is durable through its driving gear, pads, and conveyor chutes of high quality steel against corrosion.
