Recirculating Oil Pump Drive Screw Hsnh210 46A Suppliers and Manufacturers

Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series - 20 Mtr. Head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust loads - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS Pumps are available Specification Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph - Power Range : 7.5 kW to 75 kW (10 HP to 100 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Thrust Load : 7.5 kW -30 kW -10000 lbs - Speed : 2880 RPM - Head Range : 12 Mtr. To 440 Mtr. - Discharge Range : 2400 LPM to 300 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : Star Delta (SD) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5

Salient Features Highly efficient 3-phase water filled motor - Easily rewindable - Dynamically balanced design - Extended life with flawless performance - Thrust bearing : Carbon + S.S. material for High thrust load capacity - 100% EC grade copper winding - Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps. - Zero maintenance - Superior performance - Sand proof operation - Highly efficient 3-phase water filled motor Product Specification Power Range : 1.0 HP to 20.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 20000 Wp Input Solar DC Voltage Range : 110 Vmp - 600 Vmp Head Range : 30 Mtr , 220 Mtr Discharge Range : 10000 LPD - 420000 LPD Type of Duty : S1 material of construction - motor Part Grade Body Lock : Spring Steel Stud Ring : M.S. (Zinc Coated) Stator Stamping : CRNGO - M45 Silicon Winding Wire : 100% EC Copper Shaft : SS-420 Rotor Stamping : CRNGO - M45 Silicon Copper Lamination : 100% EC Copper Upper Housing : SS-304 Lower Housing : SS-304 Connection Piece : SS-304 Oil Seal : NBR TB Set : Carbon + SS Base : SS-304 Drain Plug : Brass Couple Sleeve : Stainless Steel Water Bolt : Brass MATERIAL OF CONSTRUCTION PUMP Part Grade Suction : SS-304 Couple : Stainless Steel Couple Counter : SS-304 Rubber Seal : NBR Bush Seal Cover : SS-304 Bowl : SS-304 Impeller : SS-304 Key : SS-410 Bowl Bush : NBR Bush : LTB-4 Middle : SS-304 Cap : NBR Outlet : SS-304

Type: Outboard Motor Year: Current Model: F40 HP Jet Drive Model Number: F40JEHA Series: Four Stroke Jet Drive HP: 40 Engine Type: 3 Cylinder Displacement: 45.6 ci (747 cc) Borex Stroke: 65 x 75 mm (2.56 x 2.95in) Prop Shaft Horsepower: 30 @ 5500 RPM Compression Ratio: 9.4 RPM Range: 5000-6000 Fuel Induction System: EFI (SOHC) Fuel Type: Unleaded gasoline (minimum pump octane 87) Exhaust: Thru prop Ignition System: TCI Microcomputer CARB Rating: 3-Star Alternator Outputat WOT: 16A Starting System: Electric Lubrication: Wet Sump Oil Capacity: 2.1 quarts Recommended Engine Oil: Yamalube 4M Gear Ratio: Direct Drive Control Type: Tiller Handle Trolling Throttle Adjustment: N/A Cooling: Water, Thermostatic Control Gear Shift: F-N-R Command Link System: No Enhanced Ultimate Corrosion Protection System UCP: Standard Feature Power Trim and Tilt: No Shaft Length: 20 inch Gearcase Rotation: Jet Drive Propeller: Jet Drive Tiller Handle Kit: Optional Freshwater Flush: Yes

Product Name: High Preessure Industrial Use Transformer Vacuumizer Packaging Wxf Series Anti-Explosive Oil Free Rotary Vane Vacuum Pump Summary: We have more than 20 types chemical process pump, such as horizontal pump, submersible pump ,vertical pump, semi-submersible pump, fluoroplastic pump, axial pump ,gear pump.ect . Application: They are used for transmission of liquids (oil, sea water ,sulphuric acid, phosphoric acid, H2SiF6acid, alkali liquid) with low or high temperature, neutral or corrosive liquids ,or liquids with solid granular and widely used in petroleum chemical industry ,oil refining industry, paper ,pulp industry ,sugar industry ,mining ,etc Lots of material can be chose for different working condition, such as cast steel ,stainless steel 304,316,2205,904L, Hartz alloy C276,C22, nickel-base alloy GH600, PVDF,PP, UHMWPE-lining .etc Pump a strong seal system :packing seal ,double face mechnical seal ,cartridge mechnical seal ,API682 flushing syestem.

Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a dirty oil product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.

Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.

Mazut-100 is a fuel oil that is manufactured to GOST specifications, for example GOST 10585-75/99. GOST is the Russian system of standards. Mazut is almost exclusively manufactured in the Russian Federation, This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product has a high viscosity which drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: - "Very Low Sulphur" is mazut with a sulphur content of 0.5% - "Low Sulphur" is a mazut with a sulphur content of 0.5-1.0% - "Normal Sulphur" is a mazut with a sulphur content of 1.0-2.0% - "High Sulphur" is a mazut with a sulphur content of 2.0-3.5% - Very Low Sulfur mazut is generally made from the lowest sulfur crude feedstocks.

Virgin coconut oil is made from fresh coconut meat. The production embraces the removal of the bark, the elimination of the brown shell and washing. Then the white meat gets grounded (to obtain fine flakes) and dried. After drying the white meat goes true a screw press to extract the oil. The oil gets filtered afterwards to result in a clear oil. Ingredients Organic cold pressed coconut oil. COCONUT OIL, 100% natural, is a refined vegetable oil extracted from the dried coconut flesh of Cocos Nucifera (Coconut). COCONUT OIL is one of the vegetable oils that accumulate high levels of saturated fatty acids in the triacylglycerol fraction. COCONUT OIL contains approximately 50% of Lauric acid (saturated C12 chain). COCONUT OIL provides emollient properties and is great for moisturizing, that make it useful to be used in all cosmetic formulations. COCONUT OIL is specially indicated for lipstick, make up and soap makers. The saturated nature of COCONUT OIL provides resistance to rancidity and makes a very hard soap while at the same time producing a fluffy lather. Many cultures use coconut oil straight on their hair and skin for conditioning. PHYSICAL & CHEMICAL STANDARDS Colour 25mm cell on the lovibond colour Scale in Y+5R , not deeper than (0.9 Y+0.1R) Relative Density at 30 0C 0.920 Relative Index at 40 0C ND Moisture %( matter volatile at 105 0 C,max) 0.1 Insoluble Impurities % by mass,max < 0.02 Free fatty Acids,calculated as lauric acid % bymass,max 0.04 Iodine Value 6.4 Saponification Value >255 Unsaponifiable Matter % by mass,max

MOBILGEAR 600 XP 220 Gear Oil Mobilgear 600 XP 220 Descriptions MOBILGEAR 600 XP 220 is extra high performance gear oil that has outstanding extreme pressure characteristics and load-carrying properties, intended for use in all types of enclosed gear drives with circulation or splash lubrication systems. MOBILGEAR 600 XP 220 is designed to stay ahead of the changing needs of gearbox technology. Gearbox technology design trends are towards smaller units with similar power throughout. This increase in power density places increased demands on gear oils. MOBILGEAR 600 XP 220 is formulated to meet the stress by providing extra protection for gears.

Palm Kernel Shell (PKS) is actually the by-product from palm oil industry, PKS can be used for biomass fuel, industrial boilers to replace fossil fuels such as coal. Palm kernel shells can be processed into steam that can drive turbine engines and produce electrical or heat energy. Charcoal raw materials: Palm kernel shells can be processed into high-quality charcoal and produce greater heat energy. This is because palm kernel shells have a high fixed carbon content with specification : Gross Calorie Value : 3.600 Kcal/Kg 4.200 Kcal/Kg , Moisture : 15-20% ( Maximum 20% due to rain ) , Impurities : < 3% ( Maximum 4%) , Ash Content : < 3% ( Maximum 5%) , Size : 4-20mm. , Sulfur : < 0.3% ( Maximum 1%) .

Virgin coconut oil (VCO) can be produced from fresh coconut meat, milk, or residue. Producing it from the fresh meat involves removing the shell and washing, then either wet-milling or drying the residue, and using a screw press to extract the oil. VCO can also be extracted from fresh meat by grating and drying it to a moisture content of 10–12%, then using a manual press to extract the oil. Producing it from coconut milk involves grating the coconut and mixing it with water, then squeezing out the oil. The milk can also be fermented for 36–48 hours, the oil removed, and the cream heated to remove any remaining oil. A third option involves using a centrifuge to separate the oil from the other liquids. Virgin coconut oil looks slightly different from ordinary coconut oil and this differentiation cannot be made with the naked eye. This difference is mainly due to the presence of certain colloidal and other particles and moisture within it. On the other hand, ordinary oil is refined and is mainly left with the fatty acids in it and almost nothing else. Ideally, virgin coconut oil should be as clear as water. However, its color may vary slightly depending upon its processing. Virgin coconut oil has a very good taste and smell, like that of fresh coconuts, since it is derived from fresh coconuts and is subjected to very low, if not totally nil, heat and sunlight. It is also not refined. This preserves all the natural goodness of this oil, including a high content of vitamin-E and minerals, which are otherwise almost completely robbed from ordinary coconut oil during processes like heating, filtration, refining, and bleaching, which are done to make it colorless and odorless. Furthermore, virgin coconut oil is very effective as a moisturizing agent. Its antioxidant properties are far better than those of normal coconut oil.

The Variable Speed Drive FRENIC series is equipped with functions and performance to meet all types of requirements, and in addition it is easily maintained and environmentally friendly. The series lineup ranges from simple to advanced-function models, enabling model choices matching situations for use. Fuji Electric provide Variable Speed Drives perfect for automating and with energy saving devices like a fan pump or carrier and variable speeds.