Brass Needle Valve is used to connect the copper tubing, control the flow of liquids or gas requiring close regulating. Made of brass rods and brass material except for the gland O" rings. Technical Specification: 1. Applicable temperature will be -20 to 100 2. Max Pressure: 1.47Mpa (15kgf/cm2) 3. Recommended for use at less than 80% of max load pressure at temperature between 80 and 100.
Carter comes from an manufacturing company in , and the purchase of hydraulic needle valves has been smooth in recent years. At the beginning of last year, an excavator sold by their company for less than 6 months was complained by customer. The boom of the excavator falls too fast due to its own weight, which is easy to cause danger. Their technician found that there was a problem with the hydraulic needle valve of the hydraulic system. There were obvious wear marks at the contact point between the valve spool and valve seat of the hydraulic needle valve, which was easy to leak. The leakage of the hydraulic needle valve will cause the oil saving and speed limiting circuit of the hydraulic cylinder to be uncontrollable. The boss was very angry that the equipment sold for only half a year was complained and asked Carter to find out the cause of the hydraulic needle valve problem and solve it. Carter contacted the original manufacturer of the hydraulic needle valves and requested to replace the hydraulic needle valves. The manufacturer said that the service life of hydraulic needle valves under 450bar working condition is basically 6 months. The only way to solve this complaint is to replace the hydraulic needle valves every 6 months. Such reply made Carter speechless, because his customer would not accept the high-frequency replacement of hydraulic needle valves, which not only brought a bad user experience, but also the after-sales cost was not cheap. Carter contacted all of his hydraulic needle valve suppliers, and they all replied that they were not sure to achieve a hydraulic needle valve with a service life of 1 year under the working condition of 450bar. When browsing the website, he found and left a message on the How long is the service life of hydraulic needle valves with pressure resistance of 450bar We replied directly for 1 year or more. The next day, he told the problems encountered in purchasing hydraulic needle valves at the beginning of last year in detail. After receiving the drawing of the hydraulic needle valve, we found that the hydraulic needle valve needed by Carter has much higher requirements than the ordinary hydraulic needle valves. We replied that will select specific materials for samples, which can ensure that the hydraulic needle valves can be used for more than 1 year under normal conditions. If possible, he can directly test the samples.
Keywords:tognella valves, tognella gauge isolator needle-valves 90°angle, tognella gauge isolator needle-valves in line with lateral 1/2 interface We can supply a wide range of needle valves. Gauge isolator needle-valves in line with lateral 1/2 interface Gauge isolator needle-valves 90°angle Gauge isolator needle-valves 90° angle with lateral 1/2 interface Gauge isolator push button-valves interfaces Gauge isolator push button-valves plate interfaces We also can supply so many other kinds of valves: Tognella control valves, tognella braking valves, tognella check valves, tognella ball valves
Feature: Applicable medium: oil, water,gas and other medium. Pressure: 6000 to 10000PSI Temperature: up to 600 degree centigrade 3-way design has center-off position Flow can switch from single inlet to multiple outlets or multiple inlets to common outlet Material: SS304, 316, 316L carbon steel, brass,alloy Size : 1/8" to 1 1/2" End Connection : NPT, BSPT, ISO, G,R,PT,Socket weld, flanged end Butt weld, Tube fitting and etc. Orifice : 4.0mm Stem packing : PTFE, Grafoil. Screwed bonnet design. Leak tight seal with low operating torque. Rugged bar handle provides positive stem stem actuation Non-rotating and rotating stem tip available All valves are 100% Factory tested Specified specification available upon request OEM offered Packaging : Carton or wooden case or upon request
Valves are made from bar stock/forged material and are machined precisely. These valves used to Isolate, Calibrate and Drain the process lines. Range : :1/8" to 1" threaded.1/8"OD to 1"OD, 4mm OD to 25mm OD End connections :NPT/BSPT/BSP MOC :SS 304, SS 316, BRASS, MONEL, HASTALLOY, TEFLON, CS
The Hydraulic Cartridge Needle valve that HydraForce can't make, AAK has done it in 30 days Rogelio is from Spain and we met 1 year ago. He sent inquiries about hydraulic cartridge valves to AAK for several times. Some time ago, he came to me and asked for help to make a batch of hydraulic cartridge needle valves. The hydraulic cartridge needle valve used on the hydraulic cold drawing machine they sold to Vietnam has expired the warranty period and needs to be replaced. This hydraulic cartridge needle valve is purchased from HydraForce, and it is not a standard part. HydraForce said that this valve was produced 2 years ago, it is out of stock now and will take 3-4 months to produce it. But the customer was not satisfied with this time frame and complained to his boss. In order to catch time, Rogelio contacted more than 10 Chinese manufacturers of hydraulic cartridge needle valves. They either could not benchmark with HydraForce, or they could not meet the time, so Rogelio was anxious. Rogelio remembered that AAK had supplied HydraForce for 9 consecutive years. He believed that I can help him. According to the hydraulic cartridge needle valve drawings provided by Rogelio, the production time is only 30 days. I told him that the lead time was only 30 days, and the manufacturing quality of hydraulic cartridge needle valve was up to the standard of HydraForce, few Chinese hydraulic valve manufacturers could meet these requirements. Rogelio thought that I was ready to give up, he was willing to give AAK 40 days and paid for 100 hydraulic cartridge needle valves the next day. 30 days later, AAK sent 100 hydraulic cartridge needle valves to their Vietnam factory. Rogelio informed by email last week that it was out of his expectation that AAK still completed the production in 30 days. Their customer was very satisfied with their replacement of the hydraulic cartridge needle valves. Rogelio also specifically mentioned that he had asked more than 10 hydraulic cartridge needle valve manufacturers, their lead time was at least 50 days and can not 100% guarantee to benchmark the manufacturing quality of HydraForce. AAK was the only one that could catch up with the delivery date and also benchmarked the manufacturing quality of HydraForce. For this non-standard hydraulic cartridge needle valve, AAK has 3 advantages, which are beyond the reach of most hydraulic cartridge valve manufacturers: 1.AAK adopts Japanese OKK ultra precision machine tool, and the machining accuracy of components can reach 0.01~0.3�¼m. The precision of shape and contour is 0.003 - 0.1�¼m. Its production efficiency is 30% higher, which is the cornerstone of AAK's ability to catch up the delivery. 2. AAK has been hydraulic cartridge valve ODM manufacturer of 3 world top 500 companies for 10 years. Its quality control process is more strict than the ISO certification system. We have been focusing on details and constantly optimizing technology.
Dimon is a new buyer of a hydraulic equipment manufacturing company in the United States. In the second half of last year, he purchased 100 hydraulic needle valves from an old supplier. After receiving the goods, the hydraulic needle valves were installed on the equipment. A few months later, some users complained that the pressure supply of some equipment was insufficient. Their technicians judged that the radial jamming of the valve spool of the hydraulic needle valve resulted in no flow regulation, which would lead to the failure of the power unit. The hydraulic needle valves need to be replaced with new ones as soon as possible to eliminate user complaints. His boss is not very satisfied that problem happened on even such a small number purchasing of hydraulic needle valves. Dimon is confused why the hydraulic needle valve supplier who had cooperated for 2 years would have such quality problems. He sent some problematic hydraulic needle valves back to the factory. The manufacturer replied that the accuracy of these hydraulic needle valves met the standard, but a small deviation in the size of the valve spool was caused by the deviation of the assembler. At that time, several valves were assembled at the same time in the assembly workshop, and a few deviations were difficult to avoid. Dimon realized that even the original manufacturer replaced the hydraulic needle valves with new ones, it still can not solve the problem of the radial jamming of the valve spool for 100%. He was afraid that if there were more user complaints, could he keep his job during the probation period? Dimon decided to find a new supplier of hydraulic needle valves. He left a message on our website: Can you solve the problem of radial jamming of the valve spool of hydraulic needle valve? At first, it was hard to answer this question. After several rounds of communication, we learned the story of his purchase of these 100 hydraulic needle valves. After reviewing the working conditions and drawings of hydraulic needle valve from Dimon, as well as the pictures of hydraulic needle valves from the original supplier, AAK suggested him trying samples directly. 20 days later, AAK sent 10 samples of hydraulic needle valves made per his requirements. Two months later, Dimon sent an email to us saying that he selected 5 factories from more than 20 hydraulic needle valve manufacturers to make samples. Only the samples from AAK and another factory did not have the problem of radial jamming of valve spool during the test. Their engineers suggested that AAK should be selected to replace the 100 hydraulic needle valves with potential quality problems, because the parameters of AAK hydraulic needle valve are the most stable. The boss knew that he dared to develop new suppliers and solved the hidden quality problems, although the probation period is not over yet, Dimon was approved to become a regular in advance. He told us this story privately.
Material - Stainless Steel Model - NVEE Design pressure - 6000 psi Max temp - 240 degree C Type needle valves with hard seat are disigned for use on applications requiring complete isolation or throttling of the media. The conical metal tip press fitted ensures perfect alignment for positive bubble tight shut-off. Available with end connections in sizes from 1/8" to 1" and a wide choice in connections of female screwd, male screwed, male to female screwed or socket weld. Applications: High pressure line shut of Instrument isolation Drain valve Liquid and vapor service Technical Data: All dimensions are in mm Stem Press fitted hard chrome plated Grand packing PTFE Stem packing are Burnished for smooth valve operation Safety feature Back seating for preventing stem blowout Optional: NVEE 10: High pressure valves for 10000 psi pressure Nvee 20: High pressure valves for 20000 psi pressure Specifications: Site Type Length A Handle D Handle OD E 1/8" FxF 50 40 10 MxF 55 40 10 MxM 60 40 10 1/4" FxF 55 40 10 MxF 65 40 10 MxM 60 40 10 3/8" FxF 55 40 10 MxF 65 40 10 MxM 65 40 10 1/2" FxF 65 50 12 MxF 75 50 12 MxM 70 50 12 3/4" FxF 70 50 12 MxF 75 50 12 MxM 80 50 12 1" FxF 90 70 12 MxF 105 70 12 MxM 105 70 12
*stainless steel 316 forged body *available with straight and angle pattern *panel mounting *working pressure 6000 psig Standard export package
All types of Valves are available with extremely high-quality raw materials which can be offered in varied sizes, shapes, and surface finishes, and all our products are shipped with assured quality and authenticity checks. Types of valves : Ball valve, Butterfly valve, Industrial valve, Needle valve, Manifold valve, Monoflange valves, Knife gate valves, Gate valve, Globe valve, Check Valve, Plug Valve, and more on demand
AST solenoid valve SV13-12V-0-0-00 is an exclusive product for power units offered by Yoyik. Dongfang Yoyik Engineering Co., Ltd mainly provides hydraulic components, spare parts of power units, mechanical parts processing and so on. We have spare parts, components, replacements for generators, boiler, turbines and hydroturbines. #DF-AST solenoid valve SV13-12V-0-0-00-DF LVDT Sensor TH-6N-150-15-01 Sensor DF311180-50-01-01 High wear resistance thermal resistance WZPHAR2-02 float water level sensor MPM626W6E22C3 industrial pressure sensor RC861CZ090ZYM Eddy Current Sensor PR6422/102-110 Ammeter ESS960I Thermal resistance for steam turbines WZP2-035 Linear transducer TDZ-1E-05 LVDT Sensor TDZ-1E-20B sensor 6000TZ-A pressure switch BH-003025-003 proximity sensor for sale CWY-D0-811104-01-07-90-02 Current Transducer FPAX-A2-F1-P2-O30-5A LVDT transmitter XCBSQ-03/100-01-01 LVDT transmitter XCBSQ-01/50-01-12 Speed Monitor HY-3SFE Eddy Current Sensor PR6422/104-030 transducer for displacement measurement DET400A plasma electromagnet EPBS-G-II-150-CT/XN End face thermal resistance WZP2M-001 SPEED MONITOR XJZC-03A/Q probe 2401B-0.01 Eddy Current Sensor PR6422/102-010 speed sensor DF6101-006-065-01-03-00 magnetic pick up sensor NE6103-050-150-03-09-01-00 displacement gauge 5000TDGN-15-01101 Module TM591-B03-G00 Ignition gun EHE-20-B-1-18H-S panel GHG510 1905 R0001 SERVO VALVE CONTROLLER FBM5VH LVDT Sensor TD-1GN-0200-15-01 Water temperature sensor 32302002001 103 �± 2â?? Eddy Current Sensor PR6422/105-031 HP DIFFERENTIAL EXPANSION WT0181-A40-B01 DISPLAY UNIT NPXM-2011P5N AST solenoid valve SV13-12V-0-0-00 ZYR-DFYL-2025-1-9
Product Description - 1/8" To 2" (BSP / NPT / Metrics) 1000 PSI to 20000PSI All Types Of Alloy Steel Grade -20 C to 350 C PRESSURE:- 1000 PSI to 20000PSI Product origin - MUMBAI Key Specifications/Special Features - Female x Female Connection, Female x Male Connection Male x Male Connection,OD Tube Connection (Metric) Minimum Order Size and Packaging details - 25 PIECE
SOLENOID VALVE SV4-10-C-0-00 Since its inception, YOYIK has been adhering to the concept of "technology-led, quality-first", and has brought together a large number of top engineers and technicians in the industry. With their rich experience in power station construction and maintenance, they provide customers with a full range of services from equipment selection to installation, commissioning, and maintenance. With its strong technical strength and perfect after-sales service system, the company has become a trusted partner of many large-scale power generation projects. The following are the series of components we can provide for power plants: #DF-SOLENOID VALVE SV4-10-C-0-00-DF shut off valve in hydraulic system WJ25F1.6P Power plant shut-off valves WJ50F3.2P O-shaped sealing ring HB 7519-3.55X265 PRESSURE CONTROL VALVE F3RG06D-330 plug 14S-4S sealing ring OR-216-V Pressure relief valve AW20-NO2H-CZ cast iron butterfly valve 150DOF4PB3 Axial adjustment ring HZB253-640-02-03 industrial vacuum pump price M-209 Rubber expansion joint JGD1-10 boiler feed water pump for HPT 300-340-6S pump self-locking pipe joint AFM25-3-FPM-1.4571 DEH solenoid valve D1VW20HN5P75-24V servo valve 078N209D2 O-ring HY-SO-0054-V Hammering Motor Dual Speed Motor YD2-90L-6/4 W ac evacuation pump P-1607 solenoid valve DG4V 3 0A M U D6 60 Card sleeve type cylinder joint DFHTXRJT-040 inline stop valve KJC40C-1.6P valves hydraulic SM4-40(40)151-80/40-10-H919H globe valve disc LJC40-16 PRESSURE RELIEF VALVE YSF9-55/130KJTHB Sealing ring of cooler AEW630-1.2-100-3.4/19-21 main oil pump cushion PVH131R13AF30B252000002001AB010A Floating ball valve FQF-DN40 Combination sealing gasket 8/JB982-77/F Armored platinum thermal resistor WZGPK2-33U-M100A150J120A-M212 control valve units 4WE6D-61/EG220NZ4/V worm gear reducer gearbox M02225.OBGCC1 SOLENOID VALVE SV4-10-C-0-00 SOLENOID VALVE SV4-10-C-0-00 ZYR-DFYL-2025-1-17
AAK hydraulic valve can make ignorant mistakes, but it can't make arrogant mistakes Some peers left a message after seeing the article "making mistakes is either bleeding or death. AAK hydraulic relief valve can't call mistakes as low level mistakes" on AAK hydraulic valve website: does AAK hydraulic valve never make mistakes? This is a good question. To err is human. Not to mention a multi person organization. AAK hydraulic valve can make ignorant mistakes, but it can't make arrogant mistakes. What is the ignorant mistake? I haven't done this before. I don't know how to do it. I found that I made a mistake. If this error occurs in AAK hydraulic valve, we are willing to pay or encourage it. Why encourage mistakes? 1. Because you know you are ignorant, you won't invest too much in it. The cost of making ignorant mistakes is controllable. 2. You are ignorant this time, you will know next time. You will summarize and review. This is the process of learning. AAK hydraulic valve encourages employees to make ignorant mistakes and they grow up quickly. AAK hydraulic valve can not make arrogant mistakes. What is arrogant mistake? For example, engineer A said that I know too well about this hydraulic valve. I've been clutching my hand for a long time. It's all experience. Once it's this attitude, it's over. Because of A's arrogance, it's easy to take it for granted to do this hydraulic valve. In the production process of AAK hydraulic valves, it has always been emphasized that the most grass-roots managers have the final say. I don't want the production director to have too much power, the production boss to have too much power, and the chief engineer to have too much power. Grassroots managers, who are immersed in the specific operating procedures of hydraulic valves, know how to do better than you. AAK senior managers of hydraulic valves discuss with them to provide some experience in the hydraulic valve industry and give them some suggestions. For example, although I don't operate the hydraulic valves or specific things in the company, I like to make suggestions and ponder. If the suggestion I mentioned, the idea, can inspire them, then use it. If you don't think so, let it go. In AAK hydraulic valve, if things are not done well, first admit your ignorance and don't be arrogant. What really causes us trouble is not what we don't know, but what we think we know. Only by maintaining a spirit of exploration can it become a biological tissue and grow freely. Only in this way, AAK hydraulic valve can have a future. AAK hydraulic valve, zero tolerance for arrogant errors. AAK HYDRAULIC VALVES (227) 2022-05-15
For Hydraulic Fully Adjustable Needle Valve equivalent to SUN NFBC, AAK received inquiries from a new customer in Russia Last week, we received an inquiry from a new customer in Russia for SUN NFBC Fully Adjustable Needle Valve. This is a valve that we posted in March this year, under part number E-NFBC. It has passed our internal testing for performance and durability. The advantages of AAK Hydraulic Fully Adjustable Needle Valve E-NFBC are: 1. The quality of this valve is benchmarking SUN, but price is much cheaper. 2. The service life is 2 times that of domestic hydraulic cartridge valve manufacturers in China Technical parameters of AAK E-NFBC Fully Adjustable Needle Valve: Max. Operating Pressure: 350 bar (5000 psi) Capacity: 20 lpm (5 gpm) Adjustment - No. of CCW Turns from Fully Closed to Fully Open: 5 Cavity: T-162A AAK E-NFBC Hydraulic Fully Adjustable Needle Valve, benchmarking SUN NFBC, its service life is 2 times that of its domestic peers. You are welcome to give it a try. AAK HYDRAULIC CARTRIDGE VALVES (802) 2024-06-24
American hydraulic needle valve can not solve the problem of oil temperature rise, and AAK solved it at one time by changing the throttle area Levi is from a Canadian hydraulic equipment manufacturing company. He has purchased hydraulic needle valves from AAK for several years. We often have some discussion about hydraulic valves. In the second half of last year, they wanted to launch a new high-frequency four column hydraulic press, but the test was not successful. The hydraulic oil temperature is too high, resulting in unstable equipment running speed. Their engineers checked each circuit and found no problems. No abnormality was found in each hydraulic component, including the hydraulic needle valve. Levi contacted the original hydraulic component suppliers and did not receive any positive suggestions. A week passed without any progress, and the boss was worried. Levi thought of AAK. Although this batch of hydraulic needle valves was purchased from American manufacturer due to time constraint, some problems of the hydraulic needle valves in previous times were solved by AAK. AAK engineers found out the problem 1 day later according to the system schematic diagram, commissioning video and drawings of core hydraulic components provided by Levi. The probable reason is that the hydraulic needle valve has a problem. Levi doesn't believe it, because the hydraulic needle valves come from an American factory, they also tested the hydraulic needle valves separately, and there is no abnormality. AAK can redesign the hydraulic needle valve and send samples within 3 weeks. If AAK hydraulic needle valve can not solve the running speed problem of the equipment, we will return the trial order fee. Levi thinks there is no risk. Maybe this is also hope. 3 weeks later, we sent out the trial order of 10 hydraulic needle valves. Their engineers replaced the original hydraulic needle valves, and the four column hydraulic press was continuously tested for 48h. Although the oil temperature was also high, the speed of equipment operation was stable and the equipment operated normally. Levi was surprised that AAK newly designed hydraulic needle valve was more awesome than their American manufacturer. Their engineers admired AAK for finding and solving problems. Our customer in Belarus encountered similar problems last year, so our engineers quickly found the problem. The use frequency of this four column hydraulic press is twice as high as that of the normal one. The equipment works at high frequency for a short time, resulting in an increase in oil temperature and a decrease in oil viscosity. In this way, the flow of oil through the small hole of the hydraulic needle valve increases, which leads to a change in the originally set working speed and leads to the instability of the equipment. If the flow area of the orifice of the hydraulic needle valve is changed, the running speed of the equipment can be controlled by reducing the flow.
For high pressure hydraulic needle valves that can benchmark Germany HAWE, AAK is the only manufacturer in Ningbo This morning, I received the order of 2,000 hydraulic needle valves from Charlotte. At first, I thought she sent the email by mistake, because Charlotte had no cooperation with AAK, we just discussed the inquiry for her hydraulic needle valve with pressure resistance of 450bar for 3 times. It is the first time I met a hydraulic valve customer who placed a big order after 3 times of communication. I asked her directly why she gave AAK such a large quantity of hydraulic needle valves order in only the first cooperation. Charlotte said that this hydraulic needle valve was purchased from HAWE in Germany 3 years ago, because HAWE is the best manufacturer of high-pressure hydraulic valves in the world. Charlotte is from a hydraulic equipment company in Spain. Last month, their company tried to purchase this high-pressure hydraulic needle valve from Ningbo, which is the hometown of hydraulic valves in China. She has a hydraulic valve supplier who has cooperated for 5 years and has high mutual trust. Due to the special requirements and urgent delivery date of this hydraulic needle valve, the original hydraulic valve supplier was unable to bear it, so he suggested Charlotte contact AAK, and joked that if AAK could not complete this hydraulic needle valve, she should not waste more time in Ningbo, but go back to HAWE to purchase the high-pressure hydraulic needle valves. I received the drawings and working condition requirements from Charlotte. This customized hydraulic needle valve is applied to aviation equipment. The working condition pressure is required to reach 450bar. It is required to be delivered within 50 days. The quality needs to be comparable to that of HAWE in Germany. Just like Ningbo counterpart said, in Ningbo, there may not be a second manufacturer who is able to produce this high-pressure hydraulic needle valve except AAK hydraulic valve. Charlotte was curious about why the Ningbo counterparts recognized AAK high-pressure hydraulic needle valves so much, and AAK was also so confident in its own high-pressure hydraulic valves. What is the strength of AAK high-pressure hydraulic needle valves? Like horse racing, if you want to win the gold medal, then a good horse should be equipped with a good saddle and a good rider. What are the good horses, saddles and riders of AAK? If you need to meet the following 3 points at the same time, you may not be able to find a second hydraulic valve manufacturer in Ningbo to produce high-pressure hydraulic needle valves, except AAK hydraulic valve. 1. Good horses: AAK has high-precision machine tools imported from Switzerland, Mikron GF high-precision CNC machining center and GILDEMEISTER turn milling composite machining center. 2.
The email from Draper this morning made me in a good mood all day. I had two bowls of rice at noon. He said that 5 months have passed since AAK supplied the hydraulic needle valves in September last year, they have not received any complaints from users. His owner finally accepted his suggestion: "AAK is the preferred supplier for hydraulic needle valves, even if the price is 20% more expensive". Draper, whom we met in 2019, is a purchasing veteran of Doedijns company in the Netherlands. In 2019, he purchased 3 small batches of hydraulic needle valves from AAK in 3 times. He was very satisfied with the quality and service of AAK hydraulic valves, but in the recent two years of 2020 and 2021, he basically just placed orders for the very difficult and small quantity of hydraulic valves. Draper told the truth privately that he couldn't persuade the owner to place a big order with AAK. The problem is the price. Sometimes the price of AAK hydraulic valves is 20% higher than that of other manufacturers. Only the orders that are out of the capacity other hydraulic valve manufacturers will be placed with AAK. Last July, Draper sent us an email with the subject of "the production time of 1200 hydraulic needle valves". Because he had never sent an inquiry for such a big quantity of hydraulic needle valves, I thought that he sent the email to us by mistake. After communication, it was learned that he finally persuaded the owner to place big order with AAK even if the hydraulic needle valve is 20% more expensive, because they don't want to waste time on the after-sales for the hydraulic needle valves. In the past 2 years, customers have complained more and more about the hydraulic needle valves purchased by Draper. The complaints are basically about some small details of the hydraulic needle valves. For example, the hidden burr of the hydraulic needle valves in the hydraulic power system is not completely cleaned, which affects the matching accuracy and assembly of various parts in the system, as well as the tightness of the matching interface, resulting in internal leakage. Some hydraulic needle valves are complained by users after being used for even only 3 months. For many times, they needed to replace the hydraulic needle valves for users with new ones, which wasted too much of time due to after-sales and also interrupted the construction progress of users. The 1200 hydraulic needle valves purchased from AAK this time are the repeat order for their old customer. The customer said that they will not accept the repair of hydraulic power equipment within 6 months for any reason. Draper once again suggested the owner purchase the hydraulic needle valves from AAK, because in the past 3 years, there has never been any abnormal quality of any hydraulic valves purchased from AAK within 12 months.
Ambu Bag Resuscitator Product Code: MED 119 Specifications: Sterile, individually packed in a polybag Size/Strength: Infant Description 250ml. self-inflating double ended silicone bag with mounts incorporating Reservoir valve and side feed oxygen inlet Type â??Lâ?? nonrebreathing valve with pressure limiting device wherein it will open if the inspiratory pressure is more than 40cms of water Size 0 Clearhood facemask with silicone cuff 2mtrs oxygen enrichment tubing & 2600ml Reservoir bag all in a carrying case.
Single Bonnet Needle Valve
