EcoTexTM-SL20 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION New generation eco-friendly one-shot product for a high-speed shuttleless loom. It is mainly used for 6 to 203 cotton yarns sizing. This product is entirely biodegradable and ecological. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. Having high penetration power and plasticizing power for heavy construction fabrics weaving. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 5% solution - 6 to 8 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 5 to 6 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually add EcoTexTM-SL20 and mix for 2 min. 3. Add other ingredients and mix for 2 min. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�? �ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fibre penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: A strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, and weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
Non-Woven Fabric, Non-woven fabrics Disposable Mask & Respirator Products 3Ply Mask EN14683:2019 Type I/Type II/Type IIR ASTM F2100-19 Level 1/Level 2 China YY/T0969-2013 YY 0469-2011 3Ply Civil Mask TGDBX 025-2020 KIDSGB/T 38880-2020 KIDSTGDMDMA 0005-2020 Vertical Mask Non-Medical Mask EN149 FFP2 EN149 FFP3 GB2626 KN95 NIOSH N95 FDA N95 Medical Mask EN14683 2019 Type IIR ASTM F2100-19 Level 3
High Performance Fans Table Fans OTF-3327 1250 RPM Gun Metal 400mm/16 Inch Sweep 1250 RPM Speed Motor Double ball bearing motor assuring no motor jam no motor burining Innovative Design Aesthetic Looks Sleek and Stylish Aerodynamically Designed and Balanced blade for Superior Air Delivery Tilt Adjustment for Adjusting the Fan Upward & Downward at desired Angle Jerk Free and Uniform Oscillation Long lasting Powder coated guard set & Polymer Ring for anti-corrosion 100 % copper wire motor for long life 65cmm stronger air delivery 55 Watts Energy efficient motor for power saving 3 speed choices with sleek and attractive switch panel Large & Heavy base for enhanced stability
US$ 0.315 - 1.35 / Piece Calculate Margin 500000 Pieces Minimum Order 3 - 60 days Lead Time Product Details Model Number : A11 Brand Name : WinHealth Origin : China (mainland) Small Orders : Accepted Key Specifications/Special Features: Key Specifications/Special Features: Our 5-ply N95/KN95/FFP2 Face Mask provides a physical barrier to dust, seasonal allegies, car exhausted gas, PM2.5 pollution ash, smoke and microorganism. Multi-layer design blocks air pollution to protect user. Folds expand to offer full coverage over nose and mouth. Lightweight with elastic earloops, it is comfortable and easy to put on or take off. This face mask is ideal for use at home and restaurants,shops,station,office as well as other environments that require respiratory protection. The mask has 5 layers and its filtration performance reaches 95%, which is in line withinternational certification standards Shipping Information: FOB Port: China (Mainland) Lead Time : 3 - 60 days Main Export Markets: Asia Australasia Central/South America Eastern Europe Mid East/Africa North America Western Europe Payment Details: Payment Method : 50% TT Prepay ,50% Pay before Shipment or 100% TT,LC Etc
Folding Mask High Quality Popular FFP2 Disposable Anti-dust Foldable Face Shields 4ply FFP2 mask It's mainly made of PP non woven fabrics and melt-blown filter material The disposable respirator mask can be used in the environment of� high particle and dust due to the ability to filtering. Respirator Masks are made with skin-friendly non-woven fabric to prevent irritation and itchiness. The adjustable head loops have more padding than other masks, making them more comfortable for everyday use. Disposable respirator Mask� are made of 5-layers of protection. 2 non-woven outer layers, 2 melt-blown inner filters, 1 non-woven hot cotton final layer that offers superior protection without sacrificing comfort. The metal nose clip allows for a quick custom fit around� nose while ensuring there are no air gaps. The 2 elastic headbands keep the mask in place during use. Material:Non-woven Fabric+ Melt-blown Filter+ Hot Air Filter Cotton Style : Foldable Earloop Certificate : CE Function : Disposable, Anti Dust, Air Pollution, Eco-friendly,ect Feature : High Effective Filteration,
1. Chemical Name: Sodium Pyrophosphate 2. Formula: Na4P2O7, Na4P2O7, 10H2O 3. Molecular weight: 265.90, 446.06 4. Specificity: Colorless or white crystals, crystalline or granular powder. It is easily soluble in water, but is insoluble in alcohol. Density: 2.45, relative density: 2.45, melting point: 890? . The decahydrate effloresces slightly in dry air. pH of 1% solution is about 10. 5. Quality Standard: 6. Usage: It is mainly used as detergent, electroplating . ctFor food grade it is mainly used as emulsifier, buffer, nutrient, sequestrant, texturizer 7. Packing: 25kgs net paper or plastic woven bags. 8. Storage and Transport: It should be stored in a dry, ventilative and clean warehouse kept away from moisture and hot, Furthermore, it should be stored separately from poisonous Substances.
Disposable respirator Mask folded FFP2 mask manufacturer high quality CE approved face masks It's mainly made of PP non woven fabrics and melt-blown filter material The disposable respirator mask can be used in the environment of� high particle and dust due to the ability to filtering. Respirator Masks are made with skin-friendly non-woven fabric to prevent irritation and itchiness. The adjustable head loops have more padding than other masks, making them more comfortable for everyday use. Disposable respirator Mask� are made of 5-layers of protection. 2 non-woven outer layers, 2 melt-blown inner filters, 1 non-woven hot cotton final layer that offers superior protection without sacrificing comfort. The metal nose clip allows for a quick custom fit around� nose while ensuring there are no air gaps. The 2 elastic headbands keep the mask in place during use. Head Straps With NO Staples for Extra Comfort Ultimate Snug fit with a strong face seal Zero fogging when wearing glasses This protective mask cannot generate oxygen and should not be used in hypoxic environments. It is not a N95 certified Mask for USA yet. Not intended as a replacement for gas masks and medical masks. Not for use if breathing is impeded or unsteady, or during sleep. DAILY USE: Suitable for adults daily travel protection, not suitable for toxic gas environment use.
KN95 New US$ 0.455 - 2.58 / Piece 10000 Pieces Minimum Order : 3 - 30 days Product Details Model Number : KN95 Protective Mask-#5340 Brand Name : WinHealth (Future) Origin : China (mainland) Small Orders : Accepted Key Specifications/Special Features: KN95 Particulate Respirator CE FDA Certificate Over 95% effectiveness in filtering non-oil particles Product Introduction KN95 masks have over 95% effectiveness in filtering non-oil particles. For use primarily for respiratory protection against non-oil particles, such as those from sanding, sawing, grinding, sweeping, bagging, or from processing minerals, coal, iron ore, flour, and certain other substances. The inner and outer covers of KN95 masks are constructed from spunbond nonwoven fabric. Polypropylene melt-blown nonwoven is layered between the inner and outer covers. The ear loops are made of polyester elastic which is attached to the mask. The inside nosepiece is a polypropylene or PU foam. Product Specifications Product Size Specification and Appearance Requirements Product Appearance and Materials Specifications of KN95 Mask NameParameter Product name - KN95 Particulate Respirator Material - Spunbond nonwovens, melt-blown nonwovens, hot air cotton, nose clip, elastic ear loops Model - Foldable Size - 110 mm*160 mm /4.33in.*6.30in. Product application scope and purposeMainly used for respiratory protection against non-oil particles, such as those from sanding, sawing, grinding, sweeping, bagging, or from processing minerals, coal, iron ore, flour, and certain other substances. Expiration date - 3 years after production Packaging specification - 2pcs/bag; 50pcs/box; 1000pcs/Carton Usage instructions1. Hold the ear loops in both hands with the metallic strip up. 2. Put the mask against your face covering both nose and mouth. Place ear loops around both ears. 3. Adjust mask over nose and under chin. 4. Adjust the flexible strip over bridge of nose. 5. Make sure the mask fits properly, covering the nose, mouth and chin. StorageStore in a cool, dry, clean place away from fire. Store between -20â?? and 38 (-4 F and 100 F) with relative humidity below 80 % Standards KN95 mask complies with the national standard GB2626-2006 CE FDA Certificate Self-Priming, Filter-Type Mask for Respiratory Protection. This standard specifies the technical requirements, testing methods and manufacturing procedures of the mask.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
PP Woven Block Bottom Valve Bags is the ultimate solution of leak free packaging.. These bags are Laminated & specially designed with micro holes that help in exhausting the air to increase the efficiency of the filling station & close automatically.
JDI hot air gun 863 1600W BGA rework station with 3 air gun nozzles for mobile phones repair, JDI 863 desoldering rework station for phone motherboard repair, cell phone repairing BGA desoldering rework station. JDI Hot Air Gun 863 BGA Desoldering Rework Station Product Features : This hot air rework station uses heating device to warm up air which can be used to weld. There are three working channels CH1, CH2, and CH3, and the air volume and temperature of each channel can be set. Equipped with magnetic sensor, as long as holding the handle, the machine can quickly work. With auto sleep function, can set up while sleep status. Warming up quickly, accurate and stable temperature control, make it real lead-free welding. Using frequency conversion blower, which has adjustable, large range air flow, can achieve a variety of purposes. Packing List : 1pc x JDI 863 Hot Air Gun 1pc x Power Cable 3pcs x Air Gun Nozzles 1pc x Instruction Book
ATTEN ST862D Intelligent digital display rework station For PCB chip soldering repair, 1000W Whirlwind ATTEN ST-862D lead-free hot air gun soldering station, ATTEN ST-862D Hot Air Rework Station 1000W Whirlwind 20L-120L/Min. Feature: 1. The LCD screen displays the operating temperature and status to achieve visual and human-machine interaction. 2. Menu-style operation, three sets of fast temperature / air volume access keys to achieve common temperature fast switching, 100 C -480 C. 3. Strong airflow with brushless fans. 4. Plug-in heating chip replacement is fast. 5. Straight wind and spiral wind convertible. 6. Automatic sleep. 7. Temperature lock function, timed work function. 8. Software calibration temperature control function, temperature compensation, to achieve constant temperature work. Input Voltage : 220V / 110V. Power: 1000W. Temperature Range: 100~480 Maximum Air Flow:120L/min.
New-type hot-connectivity composite fiber is made from different types of modified high molecular materials through advanced composite spining technology. It has unique characteristic of melting at low temperature, and after hot treatment, it can naturally adhere without use of binder, green and environmental. The product abides by strict sanitation control standards to achieve sanitation material grade. The products include ES fiber and ETS modified polyester composite staple fiber which is initiated by the company, and can be applied to production of surface layer and guide layer of disposable sanitary articles Functional characteristic the product is a kind of chemical blend provided with advantages of the two materials. ES fiber has low melting point on the superficial layer, soft, bouffant and pervious, while the core layer has certain intensity and fiber state. ETS fiber is provided with advantages of heat bonding, high hygroscopicity and antistatic property, etc. Application scope the sanitary products are applicable to hot air penetrating technology to produce surface layer and guide layer of disposable sanitary materials such as paper diaper and sanitary towel; the conventional low-melting fiber is applicable to production of hard cotton, decorative wall board, environmental mattress, seat mat, environmental filter media, constructional acoustic damping and heat insulation materials, etc. Specification 4D*51MMã??4D*32MM
Dried Pig Ear - Dried Chicken/ Duck feet - Dried Chicken/ Duck Neck - Dried Chicken Wing - Dried Chicken Breast - Dried Chicken Heart/ Girrazd Material: from hot, new, fresh material Process: Air dried by machine Shelf Life: 2 years
Dried Pig Ear - Dried Chicken/ Duck feet - Dried Chicken/ Duck Neck - Dried Chicken Wing - Dried Chicken Breast - Dried Chicken Heart/ Girrazd Material: from hot, new, fresh material Process: Air dried by machine Shelf Life: 2 years
Product Name: Turmeric Powder,Turmeric Root Powder Place of Origin: Fujian Province,China Part of Used: Root Appearance: Light Yellow Powder, no lumps, no visible impurities Production Method: AD(Hot Air Drying) Specification: 50-400mesh according to customer requests
