V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5
Product name: Dehydrate lemon HS Code: 08055000 Color: Black Lemon & Sun Dried Lemon Botanical name: Citrus Limonum Family: Rutaceae Description: Although dried lime lost its water it keeps all the important contents like B group Vitamins, especially Vitamin C, amino acids, and traces of minerals such as calcium, iron, magnesium, phosphorus, and potassium Besides all these advantages it has a better taste than Lemon because it less sour 1- The way of drying sun-dried Lemon - The yellow dried Lemon is dried by the strong sunshine for a long time all day, especially in the summer season it is spread on the hot sand and should be flipped over from time to time to be sure that all lemon has been dried in a good way 2- Black Lemon The black lemon is dried in an electric oven after the step of sun drying so it has been put in huge electric ovens and after that, we put it again under the sun to get rid of the humidity of the oven Both types whether Black Lemon or Yellow dried Lemon are sorted by specific machines as well as trained labor. Flavor: The dried lime has a strong mix of sour, citrusy, earthy, and somewhat smoky tastes but at the same time it has lost the taste of the sweetness of fresh limes, also it has slightly bitter, which you can taste in seeds and outer skin also it has a fermented flavor because of its preservation Uses: The dried Limes are used in many countries in their cooking to add a sour taste for example in Persia the people use dried lime in soups and stews also across the Persian Gulf they use it with fish but in Iraq noomi basra has been used in almost dishes and meals also they add it to warm drinks like Hamidh. The dried Limes are a traditionally important ingredient that is used as a powder in Persian Gulf Baharat which is added to Kabsa The benefits of dried limes: First, dried lemon helps to prevent various heart diseases, because of the benefits of black lemons to the heart muscle, and their ability to regulate blood pumping also doctors advise using it as a treatment for heart palpitations. Second, it helps expel harmful bacteria in the digestive system collect the accumulated waste and toxins in various parts of the body, and expel them to outside Third, although it can get the appetite it also is used in diet and to lose fat because it contains Vitamins and minerals which help to lose fat and calories NO BROKERS PLS FOR MORE INFO & ORDER CONTACT THE SPECIALIST NOW (24/7)
Product name: Dried Lemon HS Code: 08055000 Black Lemon & Sun Dried Lemon Botanical name: Citrus Limonum Family: Rutaceae Description: Although dried lime lost its water it keeps all the important contents like B group Vitamins, especially Vitamin C, amino acids, and traces of minerals such as calcium, iron, magnesium, phosphorus, and potassium Besides all these advantages it has also better taste than Lemon because it less sour 1- The way of drying sun-dried Lemon - The yellow dried Lemon is dried by the strong sunshine for a long time all day, especially in the summer season it is spread on the hot sand and should be flipped over from time to time to be sure that all lemon has been dried in a good way 2- Black Lemon The black lemon is dried in an electric oven after the step of sun drying so it has been put in huge electric ovens and after that, we put it again under the sun to get rid of the humidity of the oven Both types whether Black Lemon or Yellow dried Lemon are sorted by specific machines as well as trained labor. Flavor: The dried lime has a strong mix of sour, citrusy, earthy, and somewhat smoky tastes but at the same time it has lost the taste of the sweetness of fresh limes, also it has slightly bitter, which you can taste in seeds and outer skin also it has a fermented flavor because of its preservation Uses: The dried Limes are used in many countries in their cooking to add a sour taste for example in Persia the people use dried lime in soups and stews also across the Persian Gulf they use it with fish but in Iraq noomi basra has been used in almost dishes and meals also they add it to warm drinks like Hamidh. The dried Limes are a traditionally important ingredient that is used as a powder in Persian Gulf Baharat which is added to Kabsa The benefits of dried limes: First, dried lemon helps to prevent various heart diseases, because of the benefits of black lemons to the heart muscle, and their ability to regulate blood pumping also doctors advise using it as a treatment for heart palpitations. Second, it helps expel harmful bacteria in the digestive system collect the accumulated waste and toxins in various parts of the body, and expel them to outside Third, although it can get the appetite it also is used in diet and to lose fat because it contains Vitamins and minerals which help to lose fat and calories NO BROKERS PLS FOR MORE INFO & ORDER CONTACT THE SPECIALIST NOW (24/7)
Salient Features Highly efficient 3-phase water filled motor - Easily rewindable - Dynamically balanced design - Extended life with flawless performance - Thrust bearing : Carbon + S.S. material for High thrust load capacity - 100% EC grade copper winding - Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps. - Zero maintenance - Superior performance - Sand proof operation - Highly efficient 3-phase water filled motor Product Specification Power Range : 1.0 HP to 20.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 20000 Wp Input Solar DC Voltage Range : 110 Vmp - 600 Vmp Head Range : 30 Mtr , 220 Mtr Discharge Range : 10000 LPD - 420000 LPD Type of Duty : S1 material of construction - motor Part Grade Body Lock : Spring Steel Stud Ring : M.S. (Zinc Coated) Stator Stamping : CRNGO - M45 Silicon Winding Wire : 100% EC Copper Shaft : SS-420 Rotor Stamping : CRNGO - M45 Silicon Copper Lamination : 100% EC Copper Upper Housing : SS-304 Lower Housing : SS-304 Connection Piece : SS-304 Oil Seal : NBR TB Set : Carbon + SS Base : SS-304 Drain Plug : Brass Couple Sleeve : Stainless Steel Water Bolt : Brass MATERIAL OF CONSTRUCTION PUMP Part Grade Suction : SS-304 Couple : Stainless Steel Couple Counter : SS-304 Rubber Seal : NBR Bush Seal Cover : SS-304 Bowl : SS-304 Impeller : SS-304 Key : SS-410 Bowl Bush : NBR Bush : LTB-4 Middle : SS-304 Cap : NBR Outlet : SS-304
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
Description Horizontal slurry pump range offer to use in mining, chemical, and industrial applications widely. The pump is designed for heavy duty applications such as mill discharge, process plant, and tailings, high pressure pipelines, as well as other specialty applications. The pump provides excellent wear life while maintaining high efficiency during its wear cycle. It helps the new building plant to start production and recover their cost in a short time with the minimum investment. Not only our own brand slurry pumps but also it could be interchangeable with other brands on spares and whole pumps. We have stock on some regular spares. It saves the users' cost on stock and increases their supply chain's efficiency. Key Features Bearing assembly - The large diameter shaft with famous brand bearings contributes to long working life. Liners-Easy to replace and maintain. Hard metal liners are completely interchangeable with rubber or PU. Casing-Cast iron or ductile iron casing provide high operating pressure capabilities and extra protection on the safety. Impeller-Hard metal and moulded elastomer impellers are completely interchangeable with each other. High efficiency and high head designs are also available. And the arge particle is easy to pass through. FAQ: 1. Are your pump and spares interchangeable with other brands? Yes. 100% interchangeable, whatever the material, working life and working efficiency. 2. What price of your pump and spares? Our price is 30~50% of the original but the same working life. 3. What is your lead time? Some popular spares are in stock which could deliver within 5 days after your PO. If without stock, we could deliver within 3 weeks. 4. What is your warranty? One year for the whole pump except the wear parts. The working life of wet parts is the same as the most famous brand. 5. Do you have OEM service? Yes. We offer OEM service to our clients. And our engineers could train the users on site how to start, use and maintain the pumps.
Slurry pumps Range (discharge):1-18inch 2. Capacity: 10-5400 m3/h ¡¡3. Head: 5-125m ¡¡4. Impeller type: non-clog (open &close) 5. Shaft sealing: packing/gland packing & mechanical ¡¡6. Wet parts material: a05, a07, rubber, 3) slurry pump general features: 1. Xiyue brand xh/xhh slurry pumps are heavy duty pumps. They are cantilevered, horizontal, Centrifugal slurry pumps. Especially they are designed for most difficult pumping applications. 2. Xiyue xhh models are designed for heavy duty applications require high head per stage at high pressures. It is suitable for long distance transporting or where others require more than one pump in series. ¡¡3. Xiyue xh models display total interchangeability between hard metal and ¡¡¡¡elastomeric liner pumps. 4. They are mainly used in: power plant, chemical process, coal, heavy minerals, paper and pulp, mill discharge, lime grinding, bottom boiler fly, ash cyclone feed, slag granulation, suction hopper dredging, barge loading, sand reclamation ect. ¡¡¡¡¡¡ 4) slurry pump structure features: 1. Xiyue xh/xhh pumps are single stage, single suction, and overhang shaft, centrifugal, ¡¡¡¡double-casing horizontal type. Wet parts are made of abrasive resistant hard metal or rubber. ¡¡2. Bearing assembly use cylindrical structure, adjusting the space between impeller and ¡¡¡¡front liner easily, being removed completely when being repaired. ¡¡3. Bearing assembly uses grease lubrication. ¡¡4. The shaft seal could use the packing seal, expeller seal and mechanical seal. ¡¡5. The discharge branch can be positioned at intervals of 45 degrees by request and oriented ¡¡¡¡to any eight positions to suit installations and applications. ¡¡¡¡ Material construction Pump body: cast iron/grey iron Wooden box
A slurry pump refers to a machine that increases the energy of a solid-liquid mixed medium through the action of centrifugal force (the rotation of the pump's impeller), and is a device that converts electrical energy into kinetic energy and potential energy of the medium. Mainly applicable to: mining, power plants, dredging, metallurgy, chemical industry, building materials and petroleum and other industries.
Our Bentonite Products: Foundry Grade: The foundry-grade bentonite powder is used as a bonding material in the preparation of moulding sand for the production of iron, steel, and non-ferrous casting. Sodium Bentonite is the preferred binding agent for use in the bonding of metals and foundry sands, although calcium Bentonite enhances foundry sandâ??s flow ability and figures in the manufacture of nonferrous mouldings. Drilling Grade (API Grades, OCMA) Drilling-grade bentonite is a naturally occurring clay containing the clay minerals of smectite. It can also contain accessory minerals, such as quartz, mica, feldspar, and calcite. The Drilling Grade Bentonite Powder is used as a mud constituent for oil and water well drilling. Its roles are mainly to seal the borehole walls, remove drill cuttings, and lubricate the cutting head. Our Drilling Grade Bentonite Powder has high swelling and good colloidal nature, which can increase the viscosity of suspension in the drilling mud and also can increase the lubrication of drilling, as well as for the rig-freeing agent. Piling Grade Bentonite slurry is one of the most common excavation fluid used in constructing diaphragm walls. The gel strength and viscosity properties of the bentonite clay allow for cutting suspension and removal. Piling Grade Bentonite Powder is used traditionally as a support and lubricant agent in walls and foundations, tunnelling, and horizontal drilling. Viscosity and plasticity play a very important role. Bentonite slurry walls are used in construction, where the slurry wall is a trench filled with a thick colloidal mixture of Bentonite and water. Cattle Feed Grade Our Feed Grade Bentonite is Natural & selected from affluent Mines of Kutch. This Bentonite is used as an animal feed supplement, as a palletizing aid in the production of feed pallets, as well as a flow ability aid. It slows the passage of feed through the digestive system increasing the uptake of nutrients. Bentonite has an affinity for some of the active elements of toxin products formed by bacteria in the digestive tract, and its application in feed allows more rapid weight gain of livestock.
Frac Sand What Is Fracking? Fracking. We have heard the term, but do we know what it means Fracking is short for hydraulic fracturing. It's a method of extracting natural gas and oil from shale deposits deep within the earth. Water, chemicals, and sand are pumped into these shale deposits under very high pressure which causes the shale to fracture, releasing the natural gas and oil trapped within. The slurry of water, chemicals, gas, and oil are then slowly pumped back out, leaving the sand to hold the fractures open so the mixture can be removed. As the slurry of chemicals, water, sand, gas and oil is pumped back out of the ground, it is separated into its different components and stored in tanks. Description Frac sand gets its name from its use in hydraulic fracturing (fracking), a completion method used by oil and natural gas companies to produce natural gas, natural gas liquids, and oil from unconventional, low permeability reservoirs such as shale. It is a high-purity quartz sand with very round grains. It is very durable and provides a crush-resistant material used in oil and gas industries for hydraulic fracturing (also called fracking). Proppants used in the petroleum industry must meet very demanding specifications. The typical characteristics of high quality frac sand include: High-purity silica sand a grain size that is perfectly matched to job requirements a round shape that allows it to be carried in hydraulic fracturing fluid with little turbulence durability to resist the crushing forces of closing fractures. It comes in various sizes. It can be as small as 0.1 millimeter in diameter to over 2 millimeters in diameter. Most frac sand used in oil and gas industries are between 0.4 and 0.8 millimeters in size. Why Frac Sand Makes a Good Proppant? After the surface pumps are turned off, the fractures contract but do not close completely because they are propped open by billions of grains of it. This occurs when there is sufficient sand remaining in the rock to resist the force of the closing fractures.
A slurry pump refers to a machine that increases the energy of a solid-liquid mixed medium through the action of centrifugal force (the rotation of the pump's impeller), and is a device that converts electrical energy into kinetic energy and potential energy of the medium. Mainly applicable to: mining, power plants, dredging, metallurgy, chemical industry, building materials and petroleum and other industries.
Made from Hessian Cloth, Jute Hessian Bags are an environment â?? friendly option for storing. (Various agricultural products.) Available: Plain â?? are totally bio-degradable and easily blend with the. environment. Chemical Treated â?? are made rot proof to withstand with moisture and sun, for a longer period of time.Custom Printed. Also available in â??dyedâ??, â??bleachedâ?? or â??full brightâ?? colour, treated with vegetable oil for food safety. Application: Hessian Bags are widely used in the agricultural industries to store and pack varieties of commodities viz. Pulses, Food & Grains, Potatoes, Onions, Sugar, Tobacco, Coffee, Cocoa, Peanut etc. for packing goods up to 60 kgs in cement making factories for packing cement for packing sand to protect an area from land slide and flood. Common Hessian Bags: Hessian Bag Size 53â?³X77â?³ (135Ã?195 Cms), Ex. 7 Oz, Weight 1147 Grams (40.46 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 500 Bags Per Bale. Hessian Bag Size 53â?³X83â?³ (135Ã?210 Cms), Ex. 7 Oz, Weight 1234 Grams (43.54 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 500 Bags Per Bale. Hessian Bag Size 55â?³X83â?³ (140Ã?210 Cms), Ex. 7 Oz, Weight 1281 Grams (45.18 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 400 Bags Per Bale. Hessian Bag Size 53â?³X79â?³ (135Ã?200 Cms), Ex. 7 Oz, Weight 1176 Grams (41.48 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 400 Bags Per Bale. Hessian Bag Size 57â?³X69â?³ (145Ã?175 Cms), Ex. 7 Oz, Weight 1108 Grams (39.08 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 500 Bags Per Bale. Hessian Bag Size 53â?³X81â?³ (135Ã?205 Cms), Ex. 7 Oz, Weight 1205 Grams (42.51 Oz), 9Ã?8 Porter And Shots, Hemmed, Herackle Sewn On Both Side, Packing 500 Bags Per Bale. Hessian Bag Size 31â?³X20â?³ Ex. 40â?³-7oz/40â?³, 9Ã?8 Porter And Shots, Plain, Hemmed, Herackle Sewn, Packing 1000 Bags Per Bale. (For Packing Potato And Onion â?? For 25 Kg) 1Ã?20â?² FCL = 85 bales. Hessian Bag Size 31â?³X20â?³ Ex. 40â?³-7.5oz/40â?³, 9Ã?9 Porter And Shots, Plain, Hemmed, Herackle Sewn, Packing 1000 Bags Per Bale. 1Ã?20â?² FCL = 80 bales. Hessian Bag Size 40â?³X20â?³ Ex. 40â?³-10oz/40â?³, 11Ã?12 Porter And Shots, Selvedge Mouth, Herackle Sewn, Packing 1000 Bags Per Bale. Hessian Bag Size 30â?³X18â?³, Ex. 36â?³-7oz/40â?³, 9Ã?8 Porter And Shots, Hemmed, Herackle, Packing 1000 Bags Per Bale. 1Ã?20â?² FCL = 86 bales. Hessian Bag 34â?³ x 14â?³ Ex 38â?³-10oz/40â?³ 11 x12 PNS, selvedge, at mouth, 2 tie strings 20â?³ each at mouth, Herackle sewn, 1000 bags per bale,( Rot proof).(cloth width 86cm) 1 x 20 ft = 66 bales. Hessian Bag 33â?³ x 14â?³ Ex 37â?³-10oz/40â?³ 11 x12 PNS, selvedge, at mouth, 2 tie strings 20â?³ each at mouth, Herackle sewn, 1000 bags per bale, (Rot proof). (Cloth width 84cm) loading : 1 x 20 ft = 70 bales. Minimum Order: 1Ã?20
3/2C-AH Slurry Pump is a heavy-duty slurry pump that designed to handle the most abrasive and dense slurries. The 3/2C-AH slurry pump offers users a wide range of seal and liner configurations, allowing the pump to be fully customized to meet any specific application requirements. 3/2C-AH slurry pumps offer unmatched power consumption, long component life, and unmatched reliability. Tobee�® 3/2 C AH Slurry Pumps Performance Parameters: Size: 3" x 2" Capacity: 39.6-86.4m3/h Head: 12-64m Speed: 1300-2700rpm NPSHr: 4-6m Eff.: 55% Power: Max.30kw Handling solids: 25mm Seal arrangement: Packing seal, Expeller seal, Mechanical seal
3/2C-AH Slurry Pump is a heavy-duty slurry pump that designed to handle the most abrasive and dense slurries. The 3/2C-AH slurry pump offers users a wide range of seal and liner configurations, allowing the pump to be fully customized to meet any specific application requirements. 3/2C-AH slurry pumps offer unmatched power consumption, long component life, and unmatched reliability. Tobee�® 3/2 C AH Slurry Pumps Performance Parameters: Size: 3" x 2" Capacity: 39.6-86.4m3/h Head: 12-64m Speed: 1300-2700rpm NPSHr: 4-6m Eff.: 55% Power: Max.30kw Handling solids: 25mm Seal arrangement: Packing seal, Expeller seal, Mechanical seal
For Frac Sand inquiries, please contact us at agrebaja@gmail.com. BAJA CALIFORNIA, MEXICO.
Suppliers of Frac Sand Payment terms: L/C Shipping CIF/ FOB
Heavy duty slurry pumps are the most comprehensive range of Centrifugal Slurry Pumps for use in mining, chemical and general industry applications. The horizontal slurry pumps are designed for heavy duty applications such as mill discharge, power sector and tailings as well as specialty applications, which are used for continuous pumping of high abrasive, high density slurry. It is including Heavy Media Slurry Pump, Press Feeding Slurry Pump, Wet Crusher Slurry Pump , Fly Ash Slurry Pump, Flotation Slurry Pump, Mineral Processing Slurry Pump, Mineral Concentrate Slurry Pump, Coal Washing Slurry Pump, SAG Mill Discharge Slurry Pump , Thickner Underflow Pump , Mineral Sand Slurry Pump and Hydrocyclone Feed Slurry Pump.
