Introduce TRACEABLE DUCT RODDER containing metal lines, can be used to detect equipment easily detect the direction of the pipeline, as well as the location of the TRACEABLE DUCT RODDER . We can generate the TRACEABLE DUCT RODDER has two kinds, one is to be able to carry the monitoring function, one kind is the individual tracking function. The difference between the two is that with a probe into the function of a video wire inside, and a power cable, you can head the head to install the head, in order to view the situation in the pipeline. A bare copper wire can be used to locate and track the position of the TRACEABLE DUCT RODDER in a single probe function. The traceable duct rodders are available in 8mm-16mm diameter. Detectable duct rods are used to find, follow and accuratelymap the duct route without digging or trenching. The traceable duct rod is used in conjunction with both a signal transmitter and a receiver. The easily identifiable signal is transmitted along the entire length of the duct rod. The traceable duct rod has an 18 AWG copper wire, almost twice the size of the competition, in the center of the fiberglass core. The copper wire is also connected to the end fittings so the transmitter leads canmake a direct connection to the copper wire. The female end fitting provides the attachment point for the transmitter's lead connection. The other transmitter lead is connected to a stake driven into the earth. The direct connection of the signal to the copper wire provides themost effectivemethod of signal transmission.
Product:Rods Brand:Renaissance Pipe Fitting Inc. Sizes:Refer the specification Condition:New Rating:4.2, based on 42 reviews price:Start from 20 USD SS Rods, ASTM B221, UNS N06600, UNS N02200, UNS N06601, UNS N08800 High Nickel Alloy Rods, supplier. RFP India is India's well-known manufacturer, supplier and exporter of Rods, which is an iron alloy with a very low carbon (less than 0.08%) content in contrast to cast iron (2.1% to 4%), and has fibrous inclusions known as slag up to 2% by weight. Many items, before they came to be made of mild steel, were produced from rods, including rivets, nails, wire, chains, rails, railway couplings, water and steam pipes, nuts, bolts, horseshoes, handrails, wagon tires, straps for timber roof trusses, and ornamental ironwork. Rods might be round, square, rectangle or flat, and flat rods might be narrow or broad. Rod iron is usually a cut from flat bar iron in a slitting mill to provide the raw material for nails.
Cable pulling rod & push duct rodder & fiber snake rod Epoxy duct rodder is the continuous rods sizes are 4.5mm 6mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm, the duct rodders¡¯ lenghth is range 50m to 400m. Duct rodders/rods features Strong non-conductive fiberglass rod construction Stainless steel drawing head For longer conduit runs and underground duct Rugged tubular steel reel with adjustable position. Feed device allows rod to feed out or be wound back onto reel with easy pushi or pull of rod. Duct rods/duct rodders have many applications, not only pulling the cable but also pulling electric tools, and it repair is very easy, and available. Glass fiber rod diameter 4-16mm Length 100-400m Working temperature -40 ~ +80 Min bend radius 390mm Breaking tension 4500-9000kg Glassfiber density 150g/m Plastic woven 0.5*0.15*0.5m 1.5*0.5*1.5m
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod may cause increased friction in the tighter bends.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Duct rodders are composed of fiber glass rod which was extruded by fiber glass and high strength resin at high temperature. This type of rod has high tensile strength and flexibility. It was covered by a high density polyethylene engineering plastic as its protect layer, which make duct rodder cover sliding on surface, durable, corrosion resistant and has good insulation performance, which make them safe for use in cable occupied duct. High density polyethylene is used in the outer diameter coating. Duct rodders will equipped with different size reel according to the length of rod. There are wheels on the reel, which make it convenient for moving. Light weight, durable, resistance to acid, alkali, aging resistant, corrosion resistant. High tensile strength and bending properties, which make it to go through narrow pipes easily. Good temperature adaptability, the product will not soften in hot weather / nor become brittle in cold weather. Its usability will not be affected by temperature. Outer protect layer are made of high density polyethylene engineering plastic, which has good anti-uv capability. Cover was coated with long-term uv-resistant polyethylene. Its surface has the advantage of smooth, wear-resistant and long service life. There are meter marks on the protect layer of duct rodder, which can be used for measuring distance. Marks are printed by professional printing machine, which has the advantage of strong adhesion, clear writing, waterproof, anti-ultraviolet, it can be still clear even after using many times. There are several kinds of colors for the rod for your chosen.
Fiberglass Duct Rudders & Fish tapes Fiberglass Duct Rodder Duct Rodders are composed of fiber glass rod which was extruded by fiber glass and high strength resin at high temperature. This type of rod has high tensile strength and flexibility. It was covered by a high density polyethylene engineering plastic as its protect layer, which make duct rodder cover sliding on surface, durable, corrosion resistant and has good insulation performance, which make them safe for use in cable occupied duct. High Density polyethylene (Grade: for the insulating and jacketing of Telecommunication Cables) is used in the outer diameter coating. Duct Rodders will equipped with different size reel according to the length of rod. There are wheels on the reel, which make it convenient for moving. Light weight, durable, resistance to acid, alkali, aging resistant, corrosion resistant. High tensile strength and bending properties, which make it to go through narrow pipes easily. Good temperature adaptability, the product will not soften in hot weather / nor become brittle in cold weather. Its usability will not be affected by temperature. Outer protect layer are made of high density polyethylene engineering plastic, which has good anti-UV capability. Cover was coated with long-term UV-resistant polyethylene. Its surface has the advantage of smooth, wear-resistant and long service life. There are meter marks on the protect layer of duct rodder, which can be used for measuring distance. Marks are printed by professional printing machine, which has the advantage of strong adhesion, clear writing, waterproof, anti-ultraviolet, it can be still clear even after using many times. There are several kinds of colors for the rod for your chosen.
Hindalco's copper division, Birla Copper, operates one of the largest single-location custom copper smelters in the world. The custom copper smelter at Dahej in the state of Gujarat (west coast of India) houses three copper smelters, three refineries, two rod plants, a captive power plant, a captive oxygen plant, phosphoric acid plant, di-ammonium phosphate plant, precious metal recovery plant, captive jetty and other utilities. Hindalco produces LME grade copper cathodes, continuous cast copper rods in various sizes, and precious metals like gold and silver. Hindalco is one of the major manufacturers of 19.6mm diameter copper rods, which is used for railway electrification. The co-product, sulphuric acid, is partly utilised to produce phosphoric acid and fertilisers like di-ammonium phosphate (DAP). Birla Copper's brands, Birla Copper and Birla Copper II, are recognized for their high purity and consistent quality in the domestic as well as global markets. Birla Copper is an ISO 9001, 14001, 27001, 50001 and OHSAS 18001 certified company, registered on the London Metal Exchange as Grade-A copper brand, and certified as a Star Trading House having labs for chemical, mechanical and electrical testing accredited by the National Accreditation Board for Laboratories (NABL).
Technical Data of Duct Rodders 1 - Glass Reinforced Composite core: General properties: General properties Property: Value Keinforcement: E-Glass Fiber Glass Content of Inner Part: 75-80% Material of Pulling Rod: Epoxy fiber glass (inner) High density Polyethylene(outer) Density: 1.9 gr/cm3 Diameter Tolerance: ± 0.10mm Work situation temperature: - 40 0C to +800C Mechanical properties Property: Value Minimum pulling strength: 4000 N±5% Tensile Modulus: 30000 Mpa Consistency of rod: 150gr/m±5% Flexural Modulus: 30000 Mpa Elongation at Break: 2.5-3% Min. Bending Radius: 400mm Water Absorption: 0.15% after 24 hr. 2 - Polyethylene cover Material: Medium Density Polyethylene Resin for the insulating and jacketing of Telecommunication Cables. Property: Value Tensile Strength: 15N/mm2 Environmental Stress & crack resistance: >1000 hr. Heat Stability: OK. Carbon Black: OK.
duct Rodders are composed of fiber glass rod which was extruded by fiber glass and high strength resin at high temperature. this type of rod has high tensile strength and flexibility. It was covered by a high density polyethylene engineering plastic as its protect layer, which make duct rodder cover sliding on surface, durable, corrosion resistant and has good insulation performance, which make them safe for use in cable occupied duct. High Density polyethylene (Grade: for the insulating and jacketing of Telecommunication Cables) is used in the outer diameter coating. Duct Rodders will equipped with different size reel according to the length of rod. There are wheels on the reel, which make it convenient for moving. Light weight, durable, resistance to acid, alkali, aging resistant, corrosion resistant. High tensile strength and bending properties, which make it to go through narrow pipes easily. Good temperature adaptability, the product will not soften in hot weather / nor become brittle in cold weather. Its usability will not be affected by temperature. Outer protect layer are made of high density polyethylene engineering plastic, which has good anti-UV capability. Cover was coated with long-term UV-resistant polyethylene. Its surface has the advantage of smooth, wear-resistant and long service life. There are meter marks on the protect layer of duct rodder, which can be used for measuring distance. Marks are printed by professional printing machine, which has the advantage of strong adhesion, clear writing, waterproof, anti-ultraviolet, it can be still clear even after using many times. There are several kinds of colors for the rod for your chosen.
Copper Rod: Grade: 99.99 Capacity: 500 Tones Price: LME + 600$ negotiable Incoterms: CIF Orygin: Zambia Inspection: SGS or a similar inspection agency will conduct inspections at the loading port. Buyer's Rights: The buyer has the right to appoint an independent surveyor acceptable to the seller to be present during the weighing, sampling, and analysis procedures for the cargo. This arrangement is valid for both parties.
Standard ASTM B166 / ASME SB166 Dimensions ASTM, ASME and API Round Bars Size 10 mm To 100 mm Dia in 100 mm TO 6000 mm Length. Round bar Diameter 3-~800mm Hex Bar size 2-100mm A/F Square bar size 4 to 100mm Flat bar Thickness 2 -100mm Flat bar Width 10 to 500mm Length 3 to 6 meter, Custom Cut Lengths Form Round, Square, Hex (A/F), Rectangle, Wire (Coil Form), Wiremesh, Billet, Ingot, Forging Etc.,
Standard ASTM B160 / ASME SB160 Dimensions ASTM, ASME and API Round Bars Size 10 mm To 100 mm Dia in 100 mm TO 6000 mm Length. Round bar Diameter 3-~800mm Hex Bar size 2-100mm A/F Square bar size 4 to 100mm Flat bar Thickness 2 -100mm Flat bar Width 10 to 500mm Length 3 to 6 meter, Custom Cut Lengths Form Round, Square, Hex (A/F), Rectangle, Wire (Coil Form), Wiremesh, Billet, Ingot, Forging Etc.,
Standard ASTM A479 / ASME SA479 Dimensions EN, DIN, JIS, ASTM, BS, ASME, AISI Round Bars Outside Diameter in the range of 4mm to 500mm Bright Bars Outside Diameter in the range of 4mm to 100mm Hex Bars 18mm â?? 57mm (11/16â?³ to 2-3/4â?³) Square Bars 18mm â?? 47mm (11/16â?³ to 1-3/4â?³) Flat Bars 1/2â?? to 10â?? in thickness range of 2mm to 150mm Finish Black, Bright Polished, Rough Turned, NO.4 Finish, Matt Finish, BA Finish Length 1 to 6 Meters, Custom Cut Lengths Form Round, Square, Hex (A/F), Rectangle, Billet, Ingot, Forging Etc.