The main features of high-efficiency continuous casting mold copper tube material: high-efficiency continuous casting mold material with good thermal conductivity, high recrystallization temperature, high thermal fatigue resistance, high strength, good wear resistance, long service life, high efficiency continuous casting mold copper tube The main feature of the material is that the overall performance of the above properties of the copper tube material is optimal.
In order to improve the wear resistance of the chrome plating layer and prolong the service life of the copper tube of the mold, a nickel-cobalt alloy coating layer of 0.4-0.5 mm thick is added between the inner surface of the copper tube of the crystallizer and the chrome plating layer as a transition layer. Therefore, it is called nickel-cobalt alloy - hard chrome plating. Referred to as composite copper plated tube. The metal content is: the hardness of the coating is 300-600 HV.
Because nickel-cobalt alloy coating has good chemical corrosion resistance, thermal erosion resistance and wear resistance. It not only blocks the diffusion of Zn, S, Cd and F in the molten steel to the inner surface of the copper tube of the mold, but also acts as a binder between the inner surface of the copper tube of the crystallizer and the chrome plating layer, so that the chrome layer is wear-resistant. The performance has been greatly improved. In addition, after the chrome layer is worn, the nickel-cobalt alloy coating can continue to work instead of the chrome layer, thereby prolonging the service life of the crystallizer copper tube.
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP, CUAG0.1P, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Classification : Copper Pipes
A type of non-ferrous metal pipe, often divided into brass and copper pipes, is pressed and drawn seamless pipe. Copper pipe has good electrical conductivity, thermal conductivity characteristics, electronic products of conductive parts and heat dissipation parts of the main material, and has become a modern contractor in all residential commercial housing water pipeline, heating, cooling pipe installation of the first choice. Copper pipe has strong corrosion resistance and is not easy to oxidize.
Classification : Copper Pipes
A type of non-ferrous metal pipe, often divided into brass and copper pipes, is pressed and drawn seamless pipe. Copper pipe has good electrical conductivity, thermal conductivity characteristics, electronic products of conductive parts and heat dissipation parts of the main material, and has become a modern contractor in all residential commercial housing water pipeline, heating, cooling pipe installation of the first choice. Copper pipe has strong corrosion resistance and is not easy to oxidize.
123624 Copper Mould Tube Suppliers
Short on time? Let Copper Mould Tube sellers contact you.
Classification : Copper Pipes
A type of non-ferrous metal pipe, often divided into brass and copper pipes, is pressed and drawn seamless pipe. Copper pipe has good electrical conductivity, thermal conductivity characteristics, electronic products of conductive parts and heat dissipation parts of the main material, and has become a modern contractor in all residential commercial housing water pipeline, heating, cooling pipe installation of the first choice. Copper pipe has strong corrosion resistance and is not easy to oxidize.
We hold immense expertise in making available Copper in many forms
including LME registered and non registered cathodes, billets, rods,
cakes, bars, foil, sheet, granules, plates, powder, shot, turnings, wire,
insulated wire, mesh and “evaporation slugs”.
Copper is one of the most important metals. Copper is reddish with a bright metallic
lustre. It is malleable, ductile, and a good conductor of heat and electricity (second
only to silver in electrical conductivity). Its alloys, brass and bronze, are very important.
Monel and gun metals also contain copper. The most important compounds are the
oxide and the sulphate, (blue vitriol
Hollow Section steel Tube is the general name for the steel pipe other than thecircular steel pipe. Such as square, rectangle, oval,elliptical, cone, trapezoidal, spiral, etc. Different steel pipe can more adapt to the particularity of use conditions, save metal and improve the labor productivity of parts manufacturing. It is widely used in aviation, automobile, shipbuilding, mining machinery, agricultural machinery, construction, light textile and boiler manufacturing. The methods of producing different pipes are cold pulling, electric welding, extrusion and hot rolling, etc. Compared with the round tube, the different tubes generally have a larger moment of inertia and cross section modulus, and have a large bending resistance and torsion resistance, which can greatly reduce the structural weight and save steel.
Copper is found in natural ore deposits around the world. The most abundant ore are chalcopyrite and bornite, which contain both copper and iron sulphides. These account for about 80% of the worlds known ores. We supply ores with copper content within fairly narrow ranges of specifications to satisfy our customer needs
Cast Iron and Ductile Iron tube and fittings PL739
Cast Iron and Ductile Iron tube and fittings can be offered by our comapny to meet different engineering needs.
The difference between ductile iron and gray iron
1. Different chemical composition
Nodular cast iron contains nodular graphite, which can improve its toughness and strength, while reducing brittleness. Gray cast iron contains a lot of carbon, so that its hardness and wear resistance is high, but the toughness is poor.
2. Different organizational structures
The structure of nodular cast iron contains nodular and ferrite, and the distribution of nodular is uniform. While the structure of gray cast iron is mainly ferrite and pearlite, and the distribution of pearlite is uneven.
3. Different performance
Ductile iron has high strength and toughness, and has good corrosion resistance. It is uitable for the manufacture of high load and high pressure parts. The hardness and wear resistance of gray cast iron are high. It is suitable for the manufacture of friction and wear parts.
Application field
Cast iron : because of its low strength and good vibration resistance. It is often used in the production of parts under compressive stress, such as box, base, etc.
Ductile iron : because of its high strength and good toughness. It is often used in the manufacture of parts requiring high strength and toughness, such as crankshaft, connecting rod and so on.
We deals in the following products of India, China, Taiwan and Korea Origin:-
Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc)
