SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
A eucalyptus is an industrial tree which is grown for logging and creating shade. The tree is about 5 to 6 years old with a height of over 7 meters and a trunk diameter of about 9 to 10 meters. Small elongated leaves. Eucalyptus wood is used to make paper or charcoal production (white charcoal, black charcoal). People often use branches and young trees used to produce charcoal. Specification of Solid EUCALYPTUS charcoal Moisture content: 2.1% Ash content: 4.53% Volatile matter content: 28.35% Fixed carbon content: 67.12% Calorific value: 6892 kcal/kg Burning time: 3 - 3.5 hours Dimension of Solid EUCALYPTUS charcoal Shape: Solid stick Diameter: 3-8 cm Length: cut as customer's request (15-20 cm)
Finger fixing splint (tubular type) AJY-S01 Tubular finger fixation for phalangeal fractures, knuckle dislocations, ligaments, tendon injuries and fixation. 190*120*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Wrist Splint (Stable) AJY-S10 For wrist or distal forearm fractures, functional fixation of wrist arthroplasty. However, the dorsal side of the wrist needs to be exposed (if there is a wound on the volar side). 275*175*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Elbow Joint Splint (AJY-S12) It is used for elbow joint fixation for tendon, soft tissue, and nerve injury in the elbow joint in time for postoperative fixation of the joint. 448*260*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Achilles tendon dorsal splint (AJY-S11) It is used for dorsal fixation after Achilles tendon injury, topological fixation of supporting foot. 442*247*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Wrist Splint (Simple Type) AJY-S04 For wrist soft tissue injury, wrist arthritis and functional position fixation. 303*193*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Thumb plate (tubular type) AJY-S03 For the first metacarpophalangeal joint, thumb phalanx, metacarpal fracture and wrist dislocation fixation. 210*145*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Hand function position fixed splint (AJY-S09) It is used for the fixation of stable fractures of the hand and wrist, the fixation of neuromuscular and tendon injuries, and the fixation of functional positions after orthopaedic surgery. Prevent deformity caused by bone and joint disease in thumb-to-finger and palm-to-hand positions shape. 337*170*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Hand rest position fixed splint (AJY-S08) It is used for fixation after orthopedic surgery such as hand and wrist fractures, nerve tendon injuries, scar contractures, etc., to prevent or correct the deformities caused by bone and joint, neuromuscular disease. 360*210*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Thumb-fixed splint (Herringbone) AJY-S02 It is used for thumb metacarpal bone, acute metacarpal arthritis, thumb sprain, rheumatoid arthritis, post-tiger occidental occidental surgery and thumb function fixation after median nerve injury. 200*165*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Wrist Splint (Conventional) AJY-S05 For wrist or proximal forearm fractures, functional position fixation in wrist arthroplasty, and rest position system for wrist arthritis and other lesions Dynamic or lunate dislocation and colles fracture fixation. 270*192*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Wrist Splint (Tubular Type) AJY-S07 For wrist or distal forearm fractures, functional fixation of wrist arthroplasty, and rest for wrist arthritis and other lesions Position immobilization or lunate dislocation colles fracture fixation. 300*280*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
ProductASME 165 orific flanges BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating43 based on 37 reviews priceStart from 20 USD RFP India is specialized in manufacturing high quality of Orifice Flanges The main function of an orifice flange is to propose right of entry to a pipe line for metering of gases or liquids An orifice plate is packed together between a pair of flanges when its being installed in a pipe line and the whole convention is referred to as an orifice flange amalgamation Jackscrews in the gathering make a simple abolition of the orifice plate Meanwhile the orifice plate which is the metering apparatus comprises a very thin plate with a square edge concentric and round opening in the focal point Two pressure tapholes are as well penetrated in each flange for to measure the dissimilarity of pressure throughout the orifice RANGE 15 NB to 60 1500NB in 150 LBS 300 LBS 600 LBS 900 LBS 1500 LBS 2500 LBS ASA 150 ASA 300 PN 6101625 4064100160 ETC available with NACE MR 0175 SIZE 15NB to 60 1500NB CLASS PRESSURE Class Pressure 150 300 600 900 1500 2500 PN6 PN10 PN16 PN25 PN40 PN64 DIMENSION B165 BS4504 EN1092 B1636 B1647 B1648 MSS SP44 STD STD ANSI Flanges ASME Flanges DIN Flanges EN Flanges BS Flanges API JIS NACE etc FEATURES Dimensional accuracy Corrosion resistance High efficiency Excellent finish Durable Stainless Steel Orifice Flanges Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Orifice Flanges Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Orifice Flanges Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Orifice Flanges Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Orifice Flanges Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Orifice Flanges Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Orifice Flanges Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Orifice Flanges Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Orifice Flanges Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Orifice Flanges SS 310 310S Orifice Flanges Duplex Steel UNS S31803 Orifice Flanges Stainless Steel 304 304L Orifice Flanges Duplex Steel Orifice Flanges Stainless Steel 316 316L Orifice Flanges Duplex Steel UNS S32205 Orifice F
AS PS ABS PLA HDPE Granules Acrylonitrile - styrene copolymer. Acrylonitrile - styrene copolymer. A polymer composed of acrylonitrile and styrene.Typically 15-50% styrene.Transparent solid with yellow to amber needle color.The density of 1.06.It's thermoplastic.Not easy to change color.It is unaffected by diluteacids,bases, alcohols and gasoline.But soluble in acetone, ethyl acetate, dichloroethylene and so on.Can be used as engineering plastics.Excellent heat resistance and solvent resistance. Application. 1. General grade: cassettes, trash cans, toothbrush handles, lamp covers, pen tube, Cup with cover, cosmetic cases. 2. Special grade: blade of fan, batteries housing, lighters. 3. Refrigerator Sleeves, Miscellaneous 4.Used for pots, cups, milk bottles, etc., with high transparency, safety and resistance to falling 5. High Transparency, Heat Resistance, chemical resistance PC + Glass Fiber reinforced (GF) The glass fiber (GF) reinforced PC have improved tensile / flexural properties as well as thermal resistance. The FR rating improves with increase in thickness and the material can acquire a UL94 V0 rating at 3 mm. Grade: (ML3410-30 / MH3515-30 / MN-3110-30) 1) ML series: ML3405 / ML3410 / ML3420 / ML3430 (10-30% GF) General GF reinforced PC for standard application, they are characterise by balance of stiffness, modulus and impact. Application: Watch parts, switches and nobs, OA equipment. 2) MH series: MH-3515 / MH-3520 / MH-3530 (10-30% GF) Special GF reinforcements for optimal balance between modulus and improved weld line performance. MH series also improve warpage and dimensional stabilities. Applications: Watch parts, laptop housings, optical devices, mobile accessories, TV frames. 3) MN series: MN-3110 / MH-3120 / MN-3130 (10-30% GF) MN series are specially formulated for various kinds of housings and cases. They are characterise by superior impact performance, surface aesthetics and weld line strengths. Applications: Meter cases, electrical and electronic housings.
Thumb wrist joint splint (tubular type) AJY-S06 For the first metacarpophalangeal joint, interphalangeal joint and acute arthritis, wrist sprain, synovitis, carpal navicular fracture fixation. 325*185*3.2mm LOW TEMPERATURE THERMOPLASTIC SHEET Product features: Low temperature thermoplastic sheet is a new type of material made of specially synthesized polymer polycaprolactone treated by a series of chemical methods. Molecules are in a stable state at room temperature (10-30C), and can be softened after being heated in 65-70C water for 1-3 minutes. Curing in 3-5 minutes at room temperature. It has the advantages of light weight, high strength, good air permeability, not afraid of water, non-toxic, odorless, non-irritating to the skin, etc., and has biodegradability. Scope of application: 1. Fixation after reduction of fractures and joint dislocations 2. Postoperative fixation of soft tissue injuries such as joint ligaments, nerve and tendon injuries 3. Bone, joint tuberculosis, acute and chronic osteomyelitis, septic arthritis, primary bone Fixation during conservative treatment such as tumor metastasis or after debridement 4. Joint deformity, nerve palsy, cerebral palsy, scoliosis correction and postoperative fixation in children and fixed 5. Fixation after burns and other plastic surgery operations 6. Production and application of rehabilitation braces and orthoses 7. Posture placement and fixation during radiotherapy
Natures Panacea Peru Balsam Essential Oil by Aromas Oils At Aromas Oils we harness the therapeutic wonders of nature with our Peru Balsam essential oil ensuring a 100 pure product to cater to diverse needs As a leading Peru Balsam Oil Wholesale Supplier we proudly deliver quality in bulk to international customers Botany Peru Balsam scientifically known as Myroxylon Pereira belongs to the Fabaceae family Indigenous to regions of Central America and South America this tree can reach heights of 40 meters and thrives in lateritic soil Recent harvesting extends to Fiji and Indonesia Overview of Peru Balsam Essential Oil Renowned for its perfumery significance Peru Balsam essential oil is extracted through steam distillation of the oily sap from its stems Abundant in key constituents like Benzoic Acid Cinnamic Acid Benzyl Cinnamate and Cinnamyl Cinnamate it serves as a vital ingredient in various medicinal applications Peru Balsam Essential Oil Benefits Respiratory Relief With expectorant properties the oil aids in the production of lung phlegm addressing respiratory disorders Immune Strength Rich in antibacterial and antifungal properties it fortifies the immune system against germs and infections Hair Care Effectively removes dandruff and dryness from the scalp promoting healthier hair Skin Rejuvenation Ideal for saggy muscles wrinkles acne and pimples it provides effective skincare when applied before bedtime Aromatherapy A major component in aromatherapy alleviating stress anxiety depression and aiding faster sleep during insomnia Peru Balsam Essential Oil Uses Wound Healing Best remedy for minor cuts and wounds Respiratory Support Topical application on the chest relieves respiratory problems Hair and Feminine Hygiene Used in hair tonics antidandruff products and feminine hygiene sprays Fragrance in Products Acts as a natural fixative and fragrance in toiletries detergents and skincare products Peru balsam oil suppliers distributed worldwide especially in India ensure the oil reaches industrial users intact and wellpackaged Blends Well With Harmonizes seamlessly with Lavender Black Pepper Cardamom Cedarwood all Cinnamon all Copaiba Ginger Root CO2 Jasmine Absolute Lemon Orange Patchouli Peppermint Sandalwood Australian Spearmint Vetiver Ylang Ylang and Yuzu Peru balsam oil wholesale manufacturers provide these oils ensuring both quality and fair prices Precautionary Measures As responsible Peru Balsam oil bulk suppliers we recommend Diluting the oil before use and seeking expert advice for ingestion Limited information during pregnancy and lactation avoid usage during these phases to mitigate risks Excessive use may lead to kidney damage Storage Instructions Transfer oil content from aluminum containers received from Peru Balsam oil bulk manufacturers to amber dark glass bottles Store in cool dark places away from sunlight and heat to preserve essence until expiry Locations Covered As a bulk Pe
Variety Copaiba Essential Oil Explore the exotic Copaiba Essential Oil sourced from natural resinous substances of Copaifera Officinalis trees renowned for its diverse aromatic properties Aromas Oils a leading copaiba essential oil exporter ensures the delivery of this unique oil globally Botany Copaiba Essential Oil is derived from Copaiba Balsam trees widely cultivated in North amp South America Tropical Asia and Africa These trees with thick short trunks grow up to 30 meters in highly humid and temperate climates The resin known as copaiba balsam is collected from tree trunks cavities offering a highly valued medicinal aromatic stimulant herb Copaiba Essential Oil An Overview Obtained through steam distillation of copaiba oleoresins this oil is a thin pale yellow to yellow liquid with a mild woody sweet aroma and spicy peppery undertones Laden with anodyne antibacterial antimicrobial antiinflammatory astringent expectorant and digestive properties Copaiba Essential Oil is a versatile oil with numerous benefits Copaiba Essential Oil Benefits Promotes wound healing prevents fungal infections reduces swelling and relieves pain Aids in treating digestive respiratory urinary and reproductive systemrelated issues Diminishes blemishes dark spots and brightens skin tone Useful in conditions of stomach ulcers tetanus herpes and hemorrhages Alleviates insect bites sores psoriasis chilblains and eczema when applied topically Promotes relaxation of the nervous system and reduces stress Copaiba Essential Oil Uses Users worldwide both bulk and retail obtain this oil from copaiba essential oil suppliers for various applications Used as a fixative and aphrodisiac ingredient in perfumes due to its exotic aroma Applied to wounds scars or cuts for quick healing Diffused to fill surroundings with its unique fragrance Added to massage blends for relieving inflammation and pain Mixed in herbal tea or medicinal preparations Copaiba Essential Oil Blends Well With Rosewood Cedarwood Chamomile Ylang Ylang Lavender Frangipani Mimosa Cardamom Geranium Eucalyptus Ravensara and Melissa Leaf essential oils Copaiba oil wholesale suppliers offer these oils in bulk for blending Cautionary Measures Conduct a skin test before extensive use Avoid using expired or oxidized oils Dilution with other oils is recommended Ingestion should be done under the guidance of a healthcare expert Storage Instructions Transfer the oil from metal containers received from Copaiba Essential Oil manufacturers to dark glass containers to maintain quality and extend shelflife Locations Covered As a Copaiba essential oil bulk supplier the enterprise delivers products globally covering the UK US Canada Australia New Zealand South Korea China Taiwan Thailand Vietnam South Africa France Spain Poland Romania Serbia and other countries Documents Available on Request Copaiba oil wholesale manufacturers provide the following documents upon request Certific