Automatic Barrier Gate (Mitai Dz001 Series) Suppliers and Manufacturers

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stationsâ?? need, there are 48Vã??96Vã??120Vã??192Vã??220Vã??240Vã?? 360Vã??384Vã??480Vã??492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)

The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V 192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)

Product introduction: This product is composed of high quality lithium iron phosphate core (series-parallel connection) and advanced BMS management system. It adopts master-slave mode, which is convenient for monitoring and controlling the input and output system. The charging and discharging are independent, it can control the charging current of the AC charger and solar controller according to the battery temperature, voltage and SOC to better protect the battery cells from overcharging, overheating and discharging. It has high reliability and long life, products developed for applications such as solar energy storage, industrial and commercial energy storage, household energy storage, charging piles, data room and other applications. Product advantages: All-in-one design, high integration and space saving installationï¼? Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed

The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)

DC535-3/DC655-3 AUTOMATIC BARRIER BOOM GATE Using the occasion Mainly used for parking and road toll gate. Main features For control and management of parking lots, toll gates and more applications. Sine lever drive mechanism ensures quick opening and closing of the boom with soft landing. Oil immerged gear reducer. The unique transmission system ensures higher output torque. Auto-stop in the event of obstruction.Open (up) priority. Powerful balance spring. Self-locking in closed position. Manual release handle in case of power failure. Wiring terminals for red green alarm lamp, loop detector and infrared photocells.

Drive mechanism Electro- mechanical drive unit is operated by micro processor based Control panel. The drive unit consists of gears, shaft, crank, safety clutch and ball bearings etc. Which are encapsulated in weather-proof, oil filled chamber for maintenance free and long lasting performance. The operation of the Drive Unit is silent and maintenance free. Elecrical motor + HP reversible motor 24V DC, 900rpm, 40watt, maintenance free, reversible motor is designed for heavy duty operation. Dual speed and electronic braking provide optimum time for opening and closing with soft landing. Opening and closing time (2-10 sec.) can be adjusted at the site during installation depending on traffic frequency and boom length. Control panel The electronic control panel controls the direction and speed of the boom movement it is capable of accepting optional safety devices such as beam sensor, magnetic card reader, loop detector etc. The control panel can be fixed in guardroom or inside the barrier box. Push button A piano type push button is provided inside the guardroom. The barrier is activated by touching the push button for a second. Thus keeping the guard free to pay more attention to security checks. Remote control The barrier can also be activated by remote control from a distance up to 100 ft. depending upon local environmental conditions. Remote Control is an inbuilt part of the barrier and is not charged extra. Optical sensors Optical sensor (Photo beam sensor) if installed will forbid boom to come down as long as a car or a person is underneath the boom thus, extra safety is added to vehicle and boom itself (Optional). BATTERY BACK-UP In case of power failure, battery backup operation is available (Optional). Continueà..2 -2- Proximity card for unmanned barrier and limited access car parking, proximity cards/smart cards/ Biometric access systems of any make can be integrated to HOM barriers at any stage. AUTO-CLOSE MODE If auto close mode is selected in control panel, the barrier will close automatically after a preset time (10 seconds). BOOM The boom is made of non-corrosive anodized octagonal aluminum of 2mm thickness, 102mm(H) and 57mm(W). The boom length varies from 4 ft. to 30 ft. Octagonal boom profile for better visibility, strength and aesthetics. COUNTER WEIGHT M. S. Metal, rectangular shape. BOOM STAND The boom rests on a stand of height 825mm made of 77mm dia pipe of 3mm thick mild steel. BODY The body housing of the barrier is made of GI sheet of 18 gauge with dimensions: 395x283 mm x 1067 mm. The body is placed on a concrete platform with a specially designed M S angle platform bolted with the body. The weight of the entire barrier varies from 50 kg to 250 kg depending upon model. PAINT The barrier body is powder coated in Red colour. White boom has reflective Red tape stripes and a STOP sign in Red at the center of boom. IN-PUT VOLTAGE 200 û 250 V / 50 Hz. MODEL NO. WEIGHT APPROX. INPUT VOLTAGE BOOM LENGTH ADJUSTABLE OPENING TIME HB - 1000 60-80 kg 200-240 Up to 8 ft. 1.5- 4 Sec. HB - 2000 90-150 kg 200-240 9-12 ft 3- 6 Sec. HB - 2010 160-200kg 200-240 13-18 ft 4- 8 Sec HB - 2020 200-250kg 200-240 19-24 ft. 6- 10 Sec All dimensions and weight are approximate. HOMÆs continuous development program may bring specification changes without prior notice. The body housing of the barrier is made of GI sheet of 18 gauge with dimensions: 395x283 mm x 1067 mm. The body is placed on a concrete platform with a specially designed M S angle platform bolted with the body. The weight of the entire barrier varies from 50 kg to 250 kg depending upon model.

TRONCO developed flexible automatic gate systems and provide complete solutions for buildings. The systems operate easily with different constructions, door weights and places. According to design requirements, door weight can be up to 1000 kg or more. Also, the systems can be in keeping with designers' ideas to create all kinds of styles.

Electric automatic gate, keep the safety for your house, company, manufactory etc.

Aneiz F10 flap turnstile-Support OEM and ODM. Support third-party biometric devices, such as fingerprint scanner, face recognition camera. RFID card reader, QR code scanner. Aneiz F10 flap turnstile is a high performance pedestrian control turnstile. Usually used in high pedestrian traffic flow in both directions to control pedestrian entry or exit in restricted areas 304 Stainless steel material, durable, high quality, for long lasting use. The F10 features designed with standard relay signal, which can integrate easily to any kind of access control and fire systems through I/O (dry contact). In case of emergency, when power goes off both directions are free. Passing Direction: Single directional / Bi-directional. FEATURES Aneiz F10 flap turnstile -The panels of the flap turnstile extend from a pair of optical revolving door cabinets, forming a pedestrian barrier in the middle of the two cabinets. Flap turnstile is an aesthetically pleasing security and access control solution. Aneiz F10 flap turnstile -The arms will automatically retract during power failure. Flap turnstile also can be triggered to permanently open during emergency to facilitate fast evacuation. This is complying with fire safety requirements. Aneiz F10 flap turnstile -Altogether, there are 5 million cycles, 304 Stainless steel material and brushless DC motor, which guarantee greater durability and longer equipment life. Aneiz F10 flap turnstile -The turnstile designed with consolidated and more durable mechanism, will not break even someone collide it, anti-collision and anti-kick function. Aneiz F10 flap turnstile -The flaps will close automatically if there is no pedestrian passing or passenger delay to entry. IR sensors detect unauthorized or abnormal access. Alarm buzzer function will be triggered when the user is passing thru without authorization, tail gaiting, illegal intrusion or incorrect direction. Aneiz F10 flap turnstile -Multiple Operating Modes-optional IC/ID card, key fob, QR/bar code, face / fingerprint / finger vein biometric recognition, push button, ESD, wireless remote control, insert coins / card / wristband, digit counter... Aneiz F10 flap turnstile TECHINCAL SPECIFICATION Material 304 Grade Stainless Steel Cabinet Dimension 1200(L) X 300(W) X 980(H)mm Arm Material Plexiglas-transparency Passage Width 550mm standard lane Throughput 40 to 45 people per minute Response Time â?¤0.3S Net Weight 65kg/pcs single core 85kg/pcs double core Directional Mode Uni-directional or bio-directional IR Sensor 3 pairs (standard) Power Supply AC220V/110V, 50/60Hz Power Voltage 24V DC Power Consumption 40W MCBF 5 million Operating Temperature -20 �°C - 75 �°C Operating Environment Indoor or outdoor (need with shelter) Relative Humidity 95% LED Indicators Red cross means gate open, Green arrow means gate closed Warranty 18 Months

Parking barrier gate Equipment Parameters Dimension: 430 350 1050(DWH) Weight: 55KGS Power comsumption: 180W Working Voltage: AC220V/230V ± 10% 50Hz; AC110V ± 10% 60Hz; DC24V Working Temperature: -25 C~+70C Spped of Rising And Dropping: 1.2s, 3s, 6s Arm Length: 2-6 meters (the user can choose) Arm Type: barrie arm, fence arm, folding arm. Function Features Core of mechanism Using the most stable movement of the inconstant speed operation organization, parts form with hardware punched, not only the product is exquisite and portable, but also high precision and long service life; Humanized appearance design, easy operation, concise and easy; Electrical motor adopts overheating protection system, to avoid the motor heating up; The control system adopts advanced digital processing technology, with the hit protection, infrared Function etc; Host machine adopts high sensitive limit switches and time dual protection control,to make barrie stop accurately in place; In the process with anti-hit function, effectively avoid injury; With automatic delay stick down function, gate arm falls down if no vehicle pass in certain minutes; Dc option gates adopt storage battery, can run 200 times in power outage; This product can be used matching with any other access controller.

Single automatic swing gate It is built on the international advanced photoelectric inductive technology with the micro chips controller mainboard and imported main parts. It can run over 1200, 000 times with steadily performance. The frequency of the gate is between 10 to 15 seconds (optional). Power supply: 220vac/50hz Material: main tower is made with 1.5mm thick glazed stainless steel; the standing pole is made with f60*3mm steel ipe; the horizontal pole is made with f38*3mm steel pipe. All of these are chrome plated. In emergency, the gate can be opened in reverse way. After the alarm is stopped, it can be back to normal using automatically. In additional, it can add extra functions such as the alarm of reverse entry and people flow counter. There are several spare holes on the standing pole so that it can fit all the gates and guardrails of ostar series.

Dual automatic swing gateno. Em01002 Name: dual automatic swing gate Model: zm-2 Specification: l2400*w2100*h1170mm It is built on the advanced photoelectric inductive technology in world wide with the micro chips controller mainboard and imported main parts. It can run over 1200, 000 times with steadily performance. The frequency of the gate is between 10 to 15 seconds (optional). Power supply: 220vac/50hz material: main tower is made with 1.5mm thick glazed stainless steel; the standing pole is made with ft60*3mm steel pipe; the horizontal pole is made with ft38*3mm steel pipe. All of these are chrome plated. In emergency, the gate can be opened in reverse way. After the alarm is stopped, it can be back to normal using automatically. In additional, it can add extra functions such as the alarm of reverse entry and people flow counter. There are spare holes on the standing pole and it can fit all the gates and guardrails of ostar series.

Bi-directional automatic swing gate combined with face recognition technology, through high-precision face recognition algorithms, quickly verify the identity of the passer-by, to achieve contactless. Automated access control, which greatly improves the efficiency of access control through the gate, but also enhances the security. Product advantages 1.Face recognition terminal Adopting 7-inch display large screen, 200W HD dual camera, extremely fast recognition, ultra-high recognition rate, can be detected and identified within 3 metres. 2.Electric spring door opener Adopting thickened steel casting, high-strength thickened core, strong load-bearing capacity, longer service life, and can be opened in both directions. 3.Cold rolled plate process Adopting thickened steel casting, high-strength thickened core, strong load-bearing capacity, longer service life. 4.Strong load-bearing capacity Adoption of centripetal thrust cylindrical bearings improves rotational flexibility and is more capable of withstanding greater gravity. 5.Bi-directional door opening Adopting two-way opening and closing design, no need to go round or wait for either entering or leaving, which greatly improves the efficiency and comfort of people passing through.

The Maxwell Automatic Doors Company have been developed to meet all market requirements in term of security in public areas. It offers more flexibility and more comfort of use. Combining technical performance and safe design, this new range is perfect for all public resorts and heavy traffic areas: shopping centers, airports, stations, etc. it comes both for industrial and residential

Easy access to the electronic control module Automatic drop of barrier rod during power failure. Various operational methods available Build-in led light indicator Card readers can be installed Can be connected to any access control system Low maintenance requirements Positioning feature ensures the rods are always in right position Hydraulic damping system ensures quiet operation

Description K680 using advanced technology, this gate opener will be automatically stop against extra resistancesand and is equiped with optional operation mode for single or dual wing to accommodate your needs. To enhance safety and convenience, there is an manual opening design so you will still be able to close the door in case of power failure. Feature Function and Advantages 1.Soft start and slow stop 2.Automatically stop against extra resistances 3.Operational operation mode for single or dual wing 4.Available for buletooth/Mobile phone app control 5.Interface for card reader and Infrared multifunction 6.Large opening angle 180 7.Back-up power supply

Automatic folding door system offers a high standard of reliability and safety. It can continue to monitor the channel space, when case of the obstruction, the doors can be stopped automatically and using safety beam. For those who with limited mobility is security and a complete solution.

TRONCO SW30 Series Automatic Swing Door is CE EN16005 standard compliant, and is qualified by SGS for 1 million time operations durability as well as TUV quality inspection - it is nothing but best-in-class.