430 Stainless Steel Strip Specifications Grade: 430 Standard: ASTM/EN/JIS Thickness: 0.03mm-5.0 mm Width: 8.5mm-600 mm Length: coil type or it can be produced as customer requirements Surface Finish: NO.1, 2B, 2H(Rerolled Bright), BA, No.4, 8K (Mirror), HL (Hairline), Polishing Bright, etc Edge: Mill Edge, Slit Edge, Deburred Edge, Round Edge, V Type Edge 430 Stainless Steel Strip Introductions 430 stainless steel strip is a general purpose stainless steel with good corrosion resistance. It has better thermal conductivity than austenite grade stainless steel strip, a smaller thermal expansion coefficient than austenite strip, heat fatigue resistance. Due to addition of stabilizing element titanium, it has good mechanical properties of welding. Because of its chromium content, it is also called 18/0 or 18-0. Compared with 18/8 and 18/10, it contains slightly less chromium, and the hardness is correspondingly lower. 430 Stainless Steel Strip Applications 430 stainless steel strip is widely used for building decoration, fuel heating parts, hot water supply systems, household appliances, banding systems, home appliance parts and hareware. 430 Stainless Steel Strip Chemical Composition The chemical components of grade 430 stainless steel strip is summarized in the following table: Grade Standard C Si Mn P S Cr Ni Mo 430 ASTM A240 0.12 0.75 1.00 0.040 0.030 16.00-18.00 0.75
430 Annealed Stainless Steel Strip Extra Bright Annealed Soft Temper 430 Stainless Strip Steel is the most popular of all the straight chrome stainless steels Its principal use is for decorative purposes Because of its excellent heat and corrosion resistant properties its ductility and because it costs less than the chromenickel grades this Type 430 Stainless Steel Strip is used in countless applications These uses are primarily for stainless and decorative purposes including household appliances metal molding metal trim cabinet hardware hinges drawn and formed parts and stampings Type 430 Ferritic Stainless Steel Strip Characterisings Corrosion and heat resistant Ductility at about 75 of low carbon strip Similar to chromium grades with stretcher strains Roping can result from excessive stretching Able to weld for nonrigorous service Magnetic in all conditions Tensile strength annealed condition minimum of 65000 PSI yield of 30000 PSI elongation at 22
Materal stainless steel ASTM BS EN JIS Grade 201 1.4372 SUS 201 Thickness 1.0mm Width 1220mm Length 800mm Surface 2B
430 stainless steel is a universal steel with good corrosion resistance. Its thermal conductivity is better than that of austenite, its coefficient of thermal expansion is smaller than that of austenite, and it has good thermal fatigue resistance. With the addition of stabilizing element titanium, the mechanical properties of weld joints are good. 430 stainless steel is used for building decoration, fuel burner parts, household appliances and household appliances. 430F is a steel with free cutting property added to 430 steel, mainly used for automatic lathes, bolts and nuts. 430LX adds Ti or Nb to 430 steel to reduce the content of C, which improves the processability and welding performance. It is mainly used in hot water tanks, hot water supply systems, sanitary appliances, household durable appliances, bicycle flywheels, etc. Product name 430 Stainless steel sheet Grade 430 Thickness range 0.3mm-3.0mm, Width range 600mm-1500mm Length 2000mm, 2438mm, 3048mm Size 1000mm*2000mm, 1219mm*2438mm, 1219mm*3048mm, or as required Finish No. 1 , No. 4, hairline , 2b, BA, 8K, embossed, PVD color coated, sand blasted, anti-fingerprint Lead time 7 to 15 working days after the receipt Packing Wooden pallet or according to customer's request Application Interior/exterior/architectural/bathroom decoration, elevator decoration, hotel decoration, kitchen equipment, ceiling, cabinet, kitchen sink, advertising nameplate Grade C Si Mn P S Ni Cr Mo 430 0.12 0.75 1.0 0.040 0.03 0.60 16.0-18.0 - Products Display Warehouse Storage Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.
430 stainless steel coil is used for building decoration, fuel burner parts, household appliances and household appliances. 430F is a steel with free cutting property added to 430 steel, mainly used for automatic lathes, bolts and nuts. 430LX adds Ti or Nb to 430 steel to reduce the content of C, which improves the processability and welding performance. It is mainly used in hot water tanks, hot water supply systems, sanitary appliances, household durable appliances, bicycle flywheels, etc. Name 430 Stainless Steel Coil Standard JIS, AiSi, ASTM, GB, DIN, EN Material 430 Surface Treatment BA/2B/NO.1/NO.4/4K/HL/8K/EMBOSSED or according to customer requirements,etc. Width 100mm-2500mm or as required Thickness 0.1mm-4mm or as required Length As customer's request Inspection Fully accept all the third party to test before shipment. Packing Standard Export Seaworthy Package.Suit for all kinds of transport,or as required. Payment Terms L/C, T/T Stainless steel coil is a thin steel plate supplied in coils, also called strip steel. There are imported and domestic products, divided into hot-rolled and cold-rolled. According to the needs of different users, we can also order a variety of special-shaped steel materials.In order to ensure that the yield strength, tensile strength, elongation and hardness of various stainless steel coils meet the requirements, the stainless steel coils must undergo heat treatment such as annealing, solution treatment, and aging treatment before delivery.
Stainless Steel Round Tube
We have a wide variety stock of rebar, available dimensions from 8 mm to 32 mm,grades 60,40 ASTM A615,and BS4449, lengths 4,5,6,9,and 12 meters,plain,and deformed bars. Material SD390/490/400,B500B/GR460B,HRB400/500,ASTM A615 GR40/60 Standard BS4449,JIS,ASTM/A615 Length 6m,12m Application Widely used in construction industry.
Taian Henson Metal Co lTD 420J2 Stainless Steel Strip For Razor Blade 201 j3 stainless steel strip CR Stainless Steel Coil Stainless Steel Strip 201 stainless steel strip price Sus ss420 420j1 ss420j2 stainless steel strip ASTM SS 201 202 301 304 304L 309S 316 316L 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil Factory Price 420j1 420j2 Stainless Steel Coil Strip Factory In Stock For Sale 420J2 1mm Thickness Stainless Steel Strip Bright Mirror Finished Surface 420j2 Stainless Steel Coil/Sheet/Strip for Blade Razor Modified 420 420J2 Stainless Steel Divider Strip For HDD Components Stainless Steel strap02mm 4mm Thick 14404 420j2 309s Brush BA Price Stainless Steel Strip For Razor Blade 401 406 410 420J2 good price
Taian Henson Metal Co lTD 420J2 Stainless Steel Strip For Razor Blade 201 j3 stainless steel strip CR Stainless Steel Coil Stainless Steel Strip 201 stainless steel strip price Sus ss420 420j1 ss420j2 stainless steel strip ASTM SS 201 202 301 304 304L 309S 316 316L 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil Factory Price 420j1 420j2 Stainless Steel Coil Strip Factory In Stock For Sale 420J2 1mm Thickness Stainless Steel Strip Bright Mirror Finished Surface 420j2 Stainless Steel Coil/Sheet/Strip for Blade Razor Modified 420 420J2 Stainless Steel Divider Strip For HDD Components Stainless Steel strap02mm 4mm Thick 14404 420j2 309s Brush BA Price Stainless Steel Strip For Razor Blade 401 406 410 420J2 good price ASTM 201 202 301 302 304 304L 309S 316 316L 2304 254Mo 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil
Use of 430 stainless steel pipe: 1. The heater is generally used in the oil refining unit; 2. Chemical plant equipment pipeline; 3. Fast cooling cylinder for solid solution used in textile industry; 4. Seamless steel pipe for heat exchanger and condenser. 5. High pressure seamless steel pipe for food (gb-2000) is a high-quality carbon structural steel and alloy steel seamless steel pipe suitable for chemical equipment and pipes with working temperature of - 40~400 C and working pressure of 10~30ma. 6. Seamless steel pipes for geological drilling and oil drilling control. 7. Cracking pipe for petrochemical industry is used to transport high-temperature and high-pressure fluid on fertilizer equipment. 430 stainless steel pipe Standard Food Grade Sanitary Tube: JIS G3447, KS D 3585, ASTM A270, EN 10357(DIN 11850), AS 1528.1, ISO 2037(NF A49-249) Heat exchanger tube: ASTM A249 / ASME SA249, GB / T 24593-2009, HG 20537.2 Industrial pipe: ASTM A312, EN 10217-7, GB / T 12771-2008, HG 20537.3 Drinking water tube: GB / T 19228 Mechanical tube: ASTM A554, EN 10296-2 Size Outer Diameter Range: 9.5~2000mm Thickness Range: 0.5~20mm (Size can be customized.) Length: Up to 11.8 meters per piece. Shape Section Round, square, rectangular Application Sanitary tubing: for food processing industry, beverage industry, sugar mill and so on; Heat exchanger tube: condenser, boiler, super heater, evaporator and so on; Industiral pipe: for petroleum delivery, gas delivery, petrochemical industry, wastewater treatment, drainage system, and so on; Mechanical tube: handrail, railings, balustrade, hence and so on. Features: 1.Our stainless steel tubes pipes are treated by bright annealing, inside weld bead removing, precise polishing. The roughness of tubes could be under 0.3m. 2.We have the non destructive testing ( NDT ), eg. online eddy current inspection and hydraulic or airtightness testing. 3. Thick welding, good appearance.The mechanical properties of tube could be tested. 4. And Our tubes are certificated by AD 2000-W0, PED 2014/68/EU, ISO 9001 : 2015. 5. Full material traceability is guaranteed during the manufacturing process. 6. Polished tube is supplied in individual plastic sleeves with capped ends ensuring optimum cleanliness. 7. Internal Bore: Tubes have a smooth, clean and crevice free bore. Warehouse Storage Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project
We are whole supplier of ss scrap from Japan,Vietnam. Load loose in bag or bundle 20ft / 40ft. payment term: LC Or T/T. Commodity: STAINLESS STEEL GRADE 304, Grade 430.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
192 is the steel of carbon structural steel, which is a kind of alloy steel and carbon steel. The carbon content is about 0.05%~0.70%, and some can reach up to 0.90%. It can be divided into ordinary carbon structural steel and high-quality carbon structural steel. Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material A192 Thickness 0.1mm-300mm or as required Standard AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique Hot rolled,cold rolled Surface Treatment Clean, blasting and painting according to customer requirement Thickness tolerance �±0.1mm Application It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time Within 7-15 workdays after receiving deposit or L/C Export packing Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity 250,000 tons/year Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts. Warehouse Storage Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.
Performance and application of material ST37: the material has good performance, that is, through cold rolling, it can obtain cold rolled strip and steel plate with thinner thickness and higher precision, with high straightness, high surface finish, clean and bright surface of cold rolled plate in Taiwan Strait, easy to be coated, various varieties, wide application, high stamping performance, non aging, and low yield point. Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material ST37 Thickness 0.1mm-300mm or as required Standard AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique Hot rolled,cold rolled Surface Treatment Clean, blasting and painting according to customer requirement Thickness tolerance �±0.1mm Application It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time Within 7-15 workdays after receiving deposit or L/C Export packing Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity 250,000 tons/year Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts.
Classification : Hastelloy Alloy Hastelloy Bar is a versatile austenitic nickel-chromium-molybdenum-tungsten alloy with enhanced resistance to pitting, crevice corrosion and stress corrosion cracking. The high chromium content provides good resistance to oxidizing media while the molybdenum and tungst en content give good resistance to reducing media. Hastelloy Bar is particularly useful for resistance to pitting and crevice corrosion in acid-halide environments.
Product Stainless Steel coil Surface Finish 2B, BA, NO.1, NO.4, 8K, HL, Embossing, Satin, Mirror, ect Technique Cold Rolled, Hot Rolled Steel Grade 200 series: 201 202 300 series: 301 304 304L 309 310 310s 316 316L 321 400 series: 409 410 410S 420 430 439 443 Duplex:3RE60(Cr18) SAF2304 (Cr23) SAF2205 (Cr22) SAF2507(Cr25) Color Golden, Black, Sapphire Blue, Brown, Rose Gold, Bronze, Silver, ect Processing Type Cutting, bending,stamping,welding,cnc machining Cutting Type Laser cutting;water-jet cutting;flame cutting Application Interior Exterior decoration, Architectur; Evevator; Kitchen, Ceiling, Cabinet, Advertising nameplate, Roof structure, Lead Time 7-15 working days
AISI304 ss round solid free cutting stainless steel bar ProductStainless steel bar/round, flat, angle, hex etc. Diametre2mm~500mm LengthAs customer's requirements SurfaceBlack & pickled & bright & hair line Grade200 series& 300 series& 400 series StandardASTM A276, AISI,GB/T 1220, JIS G4303 ApplicationThese products are widely used in all kinds of architecture and engineering structure operation Main steel grade Available size(mm)Monthly capacity(mt)Length(mm) OEMStainless steel40~500 15004000~8000 Hot 303 303Cu 304/L 310S 316/L 321 416 42012 ~200 30004000~7000 17-4PH WLA510 ST Bar 321 304/L 316/L 310S 17-4PH WLA51019~110 20004000~7000 CD Bar Round bar303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~1005002500~6500 Square bar303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 1802500~6500 Hex bar303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 1802500~6500 CG Bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~1005002500~6500 Fetures 1) All products are made of high-quality imported raw materials. 2) Our products are certified by ISO9001:2008 authentication quality systems. 3) Excellent high temperature strength and work-hardening Trade details (kindly need your attention): 1) Above all, in your inquiry, besides the diameter , please indicate clearly: the material of your required bar; your requirement of surface polishing or not having; your requirement of fixed-length for each bar or not having. Because those are aslo key to calculating our cost and telling you prices for your ordered bars. 2) Bars can be charged by metric ton 3) Packing: standard export packing. 4) Payment:by L/C sight or T.T against copy of B/L. 5) Shipment:20-30 days after receipt of the down payment or Irrevocable L/C sight. 6) Trade terms:FOB SHANGHAI,or CIF discharging port.
AISI304 ss round solid free cutting stainless steel bar Product Stainless steel bar/round, flat, angle, hex etc. Diametre 2mm~500mm Length As customer's requirements Surface Black & pickled & bright & hair line Grade 200 series& 300 series& 400 series Standard ASTM A276, AISI,GB/T 1220, JIS G4303 Application These products are widely used in all kinds of architecture and engineering structure operation Main steel grade Available size(mm) Monthly capacity(mt) Length(mm) OEM Stainless steel 40~500 1500 4000~8000 Hot 303 303Cu 304/L 310S 316/L 321 416 420 12 ~200 3000 4000~7000 17-4PH WLA510 ST Bar 321 304/L 316/L 310S 17-4PH WLA510 19~110 2000 4000~7000 CD Bar Round bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Square bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 Hex bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 CG Bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Fetures 1) All products are made of high-quality imported raw materials. 2) Our products are certified by ISO9001:2008 authentication quality systems. 3) Excellent high temperature strength and work-hardening Trade details (kindly need your attention): 1) Above all, in your inquiry, besides the diameter , please indicate clearly: the material of your required bar; your requirement of surface polishing or not having; your requirement of fixed-length for each bar or not having. Because those are aslo key to calculating our cost and telling you prices for your ordered bars. 2) Bars can be charged by metric ton 3) Packing: standard export packing. 4) Payment:by L/C sight or T.T against copy of B/L. 5) Shipment:20-30 days after receipt of the down payment or Irrevocable L/C sight. 6) Trade terms:FOB SHANGHAI,or CIF discharging port.
AISI304 ss round solid free cutting stainless steel bar Product Stainless steel bar/round, flat, angle, hex etc. Diametre 2mm~500mm Length As customer's requirements Surface Black & pickled & bright & hair line Grade 200 series& 300 series& 400 series Standard ASTM A276, AISI,GB/T 1220, JIS G4303 Application These products are widely used in all kinds of architecture and engineering structure operation Main steel grade Available size(mm) Monthly capacity(mt) Length(mm) OEM Stainless steel 40~500 1500 4000~8000 Hot 303 303Cu 304/L 310S 316/L 321 416 420 12 ~200 3000 4000~7000 17-4PH WLA510 ST Bar 321 304/L 316/L 310S 17-4PH WLA510 19~110 2000 4000~7000 CD Bar Round bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Square bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 Hex bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 CG Bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Fetures 1) All products are made of high-quality imported raw materials. 2) Our products are certified by ISO9001:2008 authentication quality systems. 3) Excellent high temperature strength and work-hardening Trade details (kindly need your attention): 1) Above all, in your inquiry, besides the diameter , please indicate clearly: the material of your required bar; your requirement of surface polishing or not having; your requirement of fixed-length for each bar or not having. Because those are aslo key to calculating our cost and telling you prices for your ordered bars. 2) Bars can be charged by metric ton 3) Packing: standard export packing. 4) Payment:by L/C sight or T.T against copy of B/L. 5) Shipment:20-30 days after receipt of the down payment or Irrevocable L/C sight. 6) Trade terms:FOB SHANGHAI,or CIF discharging port.
AISI304 ss round solid free cutting stainless steel bar Product Stainless steel bar/round, flat, angle, hex etc. Diametre 2mm~500mm Length As customer's requirements Surface Black & pickled & bright & hair line Grade 200 series& 300 series& 400 series Standard ASTM A276, AISI,GB/T 1220, JIS G4303 Application These products are widely used in all kinds of architecture and engineering structure operation Main steel grade Available size(mm) Monthly capacity(mt) Length(mm) OEM Stainless steel 40~500 1500 4000~8000 Hot 303 303Cu 304/L 310S 316/L 321 416 420 12 ~200 3000 4000~7000 17-4PH WLA510 ST Bar 321 304/L 316/L 310S 17-4PH WLA510 19~110 2000 4000~7000 CD Bar Round bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Square bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 Hex bar 303 303CU 304/L 316/L 416 17-4PH WLA510 4.76~75 180 2500~6500 CG Bar 303 303CU 304/L 316/L 416 420 17-4PH WLA510 4.76~100 500 2500~6500 Fetures 1) All products are made of high-quality imported raw materials. 2) Our products are certified by ISO9001:2008 authentication quality systems. 3) Excellent high temperature strength and work-hardening Trade details (kindly need your attention): 1) Above all, in your inquiry, besides the diameter , please indicate clearly: the material of your required bar; your requirement of surface polishing or not having; your requirement of fixed-length for each bar or not having. Because those are aslo key to calculating our cost and telling you prices for your ordered bars. 2) Bars can be charged by metric ton 3) Packing: standard export packing. 4) Payment:by L/C sight or T.T against copy of B/L. 5) Shipment:20-30 days after receipt of the down payment or Irrevocable L/C sight. 6) Trade terms:FOB SHANGHAI,or CIF discharging port.
