OVERVIEWThis silicone is used for flock powder adhesive with great washing resistance. Since its long working time, it is available to adhere with flocking powder before it get surface-cure. Compared with waterbase ink and plastisol flocking ink, flock silicone has softer hand-feel and elasticity which is more skin-friendly. It can be applied on automatic machine production with no mesh block.TYPICAL PROPERTYCode NO. T-J04ColorTransparentDurometer - Shore A31 Shore ADynamic Viscosity200000 CentipoiseElongation520 %Pot Life72 hoursShelf Life360 DaysSolids Content> 98 %Specific Gravity @ 25C0.95Tear Strength4.1MpaTensile Strength1015.3 psiPACKING Â 5kg/barrel; 20kg/barrelCLEANING After printing, silicone ink can be cleaned away from equipment with hydrocarbon based solvent.PRODUCT DISPLAYFAQ1.What is your MOQ?It depends on customerâ??s exact request.2.Are you manufactuer or trading company?We are silicone ink and silicone heat transfer labels manufacturer, but we also do some trading based on customers trust.3.Where is your main market?Our main market based in Asian and south America countries where there are more printing factory for garments or shoes.4.What is your lead time?Normally in 3~15 days according to order quantity.5.What is your payment term ?T/T, Western Union, PayPalPRINGTING QUESTION:Advantages of flock silicone over waterbase or plastisol ink ?, PVC-free, phthalate free and heavy-metal free which is much more eco-friendly., Super soft hand-feel, elasticity and washing resistance which would not crack and more preferred by customers., Silicone on machine production is more and more popular which is also more healthy for workers.
Silica Powder Introduction Silica powder has the advantages of excellent dielectric properties ,Low coefficient of thermal expansion, Complete chemical inertness and Neutral PH ,No chemical changes or induced reactions occur in either a catalyst or multicomponent. ChangTong silica power co.Ltd??s high purity silica power is produced for the electronic materials area ,sealants, electronic potting compound area .Its dispersion leveling is excellent, contraction and Coefficient of thermal expansion are small, Acid alkali resistance ,solvent insulation,,mechanical performance, Mixed epoxy resin transparency are all good. In total ,our excellent silica power can save cost and improve effectiveness for you . Silica Powder Properties Items Unit Typical testing value Moisture % 0.08 L.O.T. % 0.1 SiO2 % ã??99.6 Fe2O3 % 0.013 Al2O3 % 0.24 K2O % 0.003 CaO % 0.02 Na2O % 0.004 Mohs hardness 7 Density g/cm3 2.65 PH 6.5-7.0 whiteness ã??90 Oil Absorption (g/100g) 16-30 Melting point (??) 1730 Silica Powder Application Production Mesh witness Mons Performance Characteristics For silicon rubber use 1000-3500 ?¥ 95 7 1.Super White; 2.Extremely low moisture; 3.Good insulativity; 4.great reinforcing effect; For paint coating use 600-2500 ?¥ 95 7 1.High White; 2.Good Oil absorption,mix viscosity, dispersity, mobility; 3.Small angle of repose,rub resistance; For sealant use 800-2000 ?¥ 92 7 1.Moisture
High performance magnesium production line 1. Iso9001: 14000 2. Lifetime service 3. Market share: 90% 1. Production capacity We can provide complete set technology solutions and supporting production equipments of magnesium production line. 1). Design capacity of single production line: 5000-25000 tons per year 2). According to client's special requirements to design. 3). We have professional process design engineers, equipment engineers, electrical engineers, etc. 4). We have more than 50 years' experiences of production design, and the market share is over 90%. 2. Main equipments: Rotary kiln, ball mill belt conveyor, vertical preheater, vertical cooler, vibrating feeder, screw conveyor, bucket elevator, bag type dust, etc. 3. Technical stepls 1) calcine dolomite: heat the dolomite to 1100~1200 temperature in the rotary kiln, then the dolomite changed into mgocao. 2) dosing ball: calculating. Dosing and grinding the mgocao...Ferrosilicon and flousper power, then press into ball. 3) reduction: heating the ball to 1200+10 tem in the reduction pot, keeping 8-10hour under the situation of 13.3pa or empty space. The mgo was reduct as magnesium vapour, then cooled into rough magnesium. 4) refining magnesium ingot.: heating the rough magnesium, and under the situation of 710 tempurature, made it into magnesium ingot, that is pure magnesium. 5) scouring: acid magnesium ingots, will with sulfuric acid, nitric acid cleaning surface or removed from the surface, make the surface appearance
Applications: Fixed frequency control circuit, apply to communication products, digital products, energy conservation and environment friendly products, massage equipment, fitness equipment, medical equipment and other household electrical appliances Product characteristics: Safety approval of ccc, cb, ul, ce, gs, bs, kc, saa, pse, tuv Low standby power consumption, meets the energy efficiency standards of eu coc v5 and us doe vi/cec vi (6) Accept customization of specification, usb output type or power cord output type Customization: eu standard, american standard, british standard, australia standard, korean standards, chinese standard Electrical characteristics: Input voltage: 100-240v ac (90-264v ac) Input current: 0.8a max Frequency: 50/60hz (47-63hz) Output voltage: 4.2-30voutput current: 0.1-4.0a No-load power consumption: 0.3w max Efficiency: 80% min Ripple and noises: 50-300mv Line regulation: â±1% Load regulation: â±5% Output protections: Short circuit protection Over-voltage protection Over-current protection environment characteristics: Hi-pot test: 3750v ac, 60s 5ma max Insulation resistance: 100mî© min Leakage current: 0.25ma max Operating temperature: 0 to 40c Storage humidity: 5-95% rh Burn-in test: rate load, 40 â±5â°c, 4 hours Emc standards: en55022 class b/fcc part 15 class b en55024/a1: 2001/en61000
Applications: Fixed frequency control circuit, apply to communication products, digital products, energy conservation and environment friendly products, massage equipment, fitness equipment, medical equipment and other household electrical appliances Product characteristics: Safety approvals of ccc, cb, ul, ce, gs, bs, kc, saa, pse & tuv Low standby power consumption, meets the energy efficiency standards of eu coc v5 and us doe vi/cec vi (6) Accept customization of specification, usb output type or power cord output type Customization: eu standard, american standard, british standard, australia standard, korean standards, chinese standard Electrical characteristics: Input voltage: 100-240v ac (90-264v ac) Input current: 0.5a max Frequency: 50/60hz (47-63hz) Output voltage: 4.2-30v Output current: 0.1-3.0a No-load power consumption: 0.3w max Efficiency: 80% min Ripple and noises: 50-300mv Line regulation: ±1% Load regulation: ±5% Output protections: Short circuit protection Over-voltage protection Over-current protection Environment characteristics: Hi-pot test: 3750v ac, 60s, 5ma max Insulation-resistance: 100m min Leakage current: 0.25ma max Operating temperature: 0 to 40c Storage humidity: 5-95% rh Burn-in test: rate load, 40 ±5c, 4 hours Emc standards: en55022 class b/fcc part 15 class b En55024/a1: 2001/en61000
Applications: Fixed frequency control circuit, apply to communication products, digital products, energy conservation and environmental protection products, massage equipment, fitness equipment, medical equipment and other household electrical appliances Product characteristics: Safety approval of ccc, cb, etl, ce, gs, bs, kc, saa, pse Low standby power consumption, meet the energy efficiency standards of eu coc v5 and us doe vi/cec vi (6) Customization: eu, american, british, australia, korean, chinese standard Electrical characteristics: Input voltage: 100-240v ac (90-264v ac) Input current: 1.5a max Frequency: 50/60hz (47-63hz) Output voltage: 4.6-36v Output current: 0.1-5.0a No-load power consumption: 0.3w max Efficiency: 87% min Ripple and noises: 50-200mv Line regulation: ±1% Load regulation: ±5% Output protections: Short circuit protection Over-voltage protection Over-current protection Environmental characteristics: Hi-pot test: 3750v ac 60s 5ma max Insulation resistance: 100mî© min Leakage current: 0.25ma max Operating temperature: 0 to 40°c Storage humidity: 5 to 95%rh Burn-in test: rate load, 40 ±5°c, 4 hours Emc standards: en55022 class-b/fcc part 15 class-b En55024/a1: 2001/en61000
Applications Fixed frequency control circuit, apply to communication products, digital products, energy conservation and environmental protection products, massage equipment, fitness equipment, medical equipment and other household electrical appliances Product characteristics Safety approval of ccc, cb, etl, ce, gs, bs, kc, saa, pse Low standby power consumption, meet the energy efficiency standards of eu coc v5 and us doe vi/cec vi (6) Customization: eu standard, american standard, british standard, australia standard, korean standards, chinese standard Electrical characteristics Input voltage: 100-240v ac (90-264v ac) Input current: 1.5a max Frequency: 50/60hz (47-63hz) Output voltage: 4.6-36v Output current: 0.1-5.0a No-load power consumption: 0.3w max Efficiency: 87% min Ripple and noises: 50-200mv Line regulation:± 1% Load regulation:± 5% Output protections Short circuit protection Over voltage protection Over current protection Environmental characteristics Hi-pot test: 3750vac 60s 5ma max Insulation resistance: 100m î min Leakage current: 0.25ma max Operating temperature: 0 to 40c Storage humidity: 5-95%rh Burn-in test: rate load, 40±5c, 4 hours Emc standards: en55022 class b/fcc part 15 class b en55024/a1:2001/en61000
8/12/15KW commercial induction cooker Machine Core: 1, 32-bit DSP machine core,high-speed operation; 2, Precise temperature control , throw pots effect; 3, Anti-interference ability and stable operation; 4, 30 kinds intelligent detection and protection 5, Longer life LED Display Connect the power, LED display shows symbol, the red indicator flicker. You can choose fire level as you need. The led display show the fire level number. 1 �- 5 �, 1 � is MIN power, 5 � is MAX power. Both of the red and green indicator lighting, it is meaning the wok is heating. After you finish cooking, move the magnetic switch to OFF �. 1.Economic efficient: heating with the principle of electromagnetic ,heat faster, thermal efficiency is up to 90% and improve the dishes rate; 2.Energy-saving: exist no heat conduction and thermal, energy-saving over 50% than the ordinary gas/oil focal , Save money = Make money 3.Environmental protection: no flame, no dust, halogen-light exhaust, ultra low noise design (below 45 db), optimized kitchen environment; 4.Safety: security protection such as waterproof, prevent smoke, prevent leakage, prevent dry heating protection ,more safe , electricity -saving 5.Intelligent design: nine gear firepower circulation adjustment, balance the power output, circulating cooling structure, 6.Beautiful apperence: stainless steel seiko meticulous humanized design, high-grade durable, easy to clean, 7. Durable: 201 durable stainless steel
Lobster, salmon, vannamei, tiger prawn, all kinds of rice, broken rice, fresh coconut, almond nut, beech nut, cashew nut, hazelnut, walnut, fresh organic honey, corn oil, coconut oil, sunflower oil, canola oil, eseential oils black and white pepper, turmeric, wheat, millet, sorghum, cumin seeds, cardamom, green chilli powder, red chilli, cloves, red chilli powder, back pepper powder, garlic, paste, powder, bay leaf, black cumin black cardamom, saffron, fenugreek, crushed maize, chile, mustard seed, corn flakes, cereal, rice bran oil, pasta, peanut butter, rice, and vegetable, corn starch, beet sugar pulp, soya bean seed, white kidney beans, lentil, gluten free wheat flour, groundnut, cardamom, t-shirts, bath towels, towels, leather hand bags, wallets, belts, jackets, antique items, coir, granite.
Thin Rice Noodles, Vermicelli, Instant Rice Noodles, Rice Sticks in Large Quantiy Our Rice Noodle Factory is a professional manufacturer with over 30 years' experience, with a production capacity of 100 metric tons a day. Besides supplying domestic market with quality products, we have also exported to quite a few foreign countries. Our rice noodles are scientifically produced with no chemical additives, just fine rice flour and drinking water. Our rice noodles can be roughly classified as plain dried rice noodle cakes with 7~9 cakes in a big bag. Consumers can cook and season them according to their personalized tastes; and as seasoned dried noodle cakes with one cake in a smaller bag with prepared sauces and seasoning powder. This can save consumers time and efforts and they can still enjoy our tasty rice noodles. Suggested ways to cook our plain dried rice noodle cakes: 1. Put enough drinking water or tap water in a pot and heat it till boiling. 2. Gently put a rice cake or cakes into the boiling water and cook for 2~3 minutes, not exceeding 5 minutes, as the rice cakes were already precooked in hot steam. 3. Dredge the rice noodles out, put them in cold water and stir them loose, then drain them a while for the next step, not exceeding 1 hour. 4. Prepare the well-drained rice noodles as soup, steamed or fried, mixed with meat, vegetables and seasonings at your own preference. Suggested ways to cook our seasoned dried rice noodle cakes: 1. Put the rice noodle cake in a bowl big enough to hold the cake. 2. Carefully pour very hot water or boiling water into the bowl and get the cake immersed. Put a cover on the bowl and let it sit for about 5 minutes. 3. If you want it served as noodle soup, just put the sauce and seasoning powder into the water and stir it into soup and enjoy the food. 4. If you want it served as dry-mixed, drain the water, put the sauce and seasoning powder onto the noodles and mix them thoroughly and enjoy the food. Your own designs of bag printing, rice noodle cakes, sauces and/or seasoning powder are welcome.
Description Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments. Recommended Use :- It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data COLOUR : Assorted FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy thinner 190 POT LIFE : 4 hours min at 30 C RECOMMENDED DFT : 30 - 40 au. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 psi For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 psi
Description Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments Recommended Use :- Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 + 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : SURFACE DRY : 60 - 90 minutes HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE at 30�°C : 4 hours min at 30�°C RECOMMENDED DFT : 30 40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel finish paints. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 p.s.i. For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : Max 5% if required Nozzle Orifice: 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data :- COLOUR :- Yellow FINISH :- Matt SOLIDS BY VOLUME :- 40 �± 3% THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT :- Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes (At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE :- BASE : 6 months HARDENER : 6 months SURFACE PREPARATION Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application Application Data MIXING RATIO :- Base : Hardener (As per our recommendation) APPLICATION :- By Brush / By Conventional Spray / By Airless Spray THINNER :- Epoxy Thinner 190 POT LIFE :- 4 hours min at 30�°C RECOMMENDED DFT :- 30 - 40 �µ. OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. For Conventional Spray application:- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 1.4 mm Nozzle Pressure : 40 - 70 p.s.i. For Airless Spray Application:- Thinner : Epoxy Thinner 190 Addition : Max 5% Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 p.s.i.
3003 Aluminum Plate 3003 aluminum plate is a popular aluminum alloy that is widely used for various applications. It is a non-heat treatable alloy with excellent corrosion resistance, good formability, and moderate strength. The alloy contains manganese as its main alloying element, which provides improved strength over pure aluminum. 3003 aluminum plate is commonly used in sheet metal works, cooking utensils, pressure vessels, and other applications that require corrosion resistance and formability. It is also used in HVAC systems, refrigeration components, and other equipment that requires good thermal conductivity. The typical mechanical properties of 3003 aluminum plate include a tensile strength range of 90-130 MPa, a yield strength range of 45-90 MPa, and an elongation of 10-25%. The alloy has a density of 2.72 g/cm3 and a melting point of 660�°C. 3003 aluminum plate is available in various sizes and thicknesses, ranging from 0.25 mm to 200 mm. It can be cut, welded, and formed easily using conventional methods. The alloy can be finished using anodizing, painting, or other surface treatments to enhance its appearance and properties. Advantages: Corrosion Resistance: One of the primary advantages of 3003 aluminum plate is its excellent corrosion resistance, making it ideal for outdoor applications. Formability: 3003 aluminum plate is a highly formable alloy, making it easy to work with and shape into complex forms. Weldability: The alloy can be welded using conventional methods, making it suitable for various applications that require joining. Thermal Conductivity: 3003 aluminum plate has good thermal conductivity, making it suitable for applications where heat dissipation is necessary. Applications: Sheet Metal Works: 3003 aluminum plate is commonly used in sheet metal works such as gutters, roofing, and siding. Cooking Utensils: The alloy is used in the manufacturing of cooking utensils such as pots, pans, and baking trays. Pressure Vessels: 3003 aluminum plate is used in the construction of pressure vessels such as tanks and boilers. HVAC Systems: The alloy is used in HVAC systems, refrigeration components, and other equipment that requires good thermal conductivity. Marine Applications: 3003 aluminum plate is widely used in marine applications due to its excellent corrosion resistance. Transportation: The alloy is used in the manufacturing of transportation equipment such as trailers, truck bodies, and automotive parts. Electrical Applications: 3003 aluminum plate is used in electrical applications due to its high conductivity and excellent formability.
Brief description YJS-525 is medium hardness silicone with hardness Shore A 25. It is a kind of of two- component materials consisting of a flowable part A which when mixed with the curing agent or catalyst,cures at room temperature by a condensation recation. It is widely used for resin, gypsum, concrete/cement and artificial stone molding. Features -Easy to demould -Good resistance to tearing -Good elastic -Good tear&tensile strength -Dimensional stability in time ( deformation - shrinking only up to 0.3 % ) -Remarkable resistance to high temperatures (up to 200 - 220â?? ) -Final curing at room temperature Specification Typical general characteristics Inspection Method Value Product data (Catalyzed A+B) YJS-525 Hardness Shore A 25�±2 Mix Ratio A:B 100:2 Color / White Pot life 25 �°C (77F) 30-40mins Curing time 25 �°C (77F) 3-4 hours Mixed viscosity mPa.s 15000�±1000 Tear-strength kg/cm â?¥25 Tensile-strength M.pa â?¥4.2 Elongation % â?¥480 Shrinkage % â?¤0.3% Package * Small size:1kg/jar A +20gram/jar B, 12 jars in one carton. MAX 336KGS in one pallet 5kg/jar A + 100gram/jar B, 6 jars in one carton. MAX 750KGS in one pallet(metal drum) 5kg/jar A+ 100gram/jar B, 4 jars in one carton. MAX 480KGS in one pallet(plastic drum) * General size: 20kg/pail A +400gram/pail B, 18 pails or 24 pails or 27 pails in one pallet 25kg/pail A + 500gram/pail B, 18 pails or 24 pails or 27 pails in one pallet 200kg/pail A + 4kg/pail B, 2 pails or 4 pails in one pallet 1kg package 12 jars in one carton. MAX 336KGS in one pallet 5kg metal drum 6 jars in one carton. MAX 750KGS in one pallet(metal drum) 5kg plastic drum 4 jars in one carton. MAX 480KGS in one pallet 20kg or 25kg plastic drum 18 pails or 24 pails or 27 pails in one pallet 20kg or 25kg metal drums 18 pails or 24 pails or 27 pails in one pallet 200kg metal drum 2 drums or 4 drums in one pallet Storage YJS-525 has a shelf life of at least 12 months in the sealed container between 5 C and 30 C. If the material is kept beyond 12 months it is not necessarily unusable, but a test should be performed on the product to check suitability to the application
What is a vacuum fryer machine? The equipment uses heat conduction medium to dehydrate and dry food under negative pressure,the processed food has very low water content and oil content, crisp but not greasy.To some extent, it preserves the original shape, color, aroma and taste of fruits and vegetables completely, and is rich in vitamins, minerals, fiber and other nutrients. It has the characteristics of low sugar, low salt, low fat and low heat. Model:XSD-WX, XSD-30,XSD-60,XSD-120 Capacity:10-100KG per hour Working temperature:70â??-120â??(adjustable) deoiling method:inner deoiling under the vacuum state deoiling speed :0-300r/min(adjustable) Material :vacuum kettle,inside storage tank:stainless steel 304 outside of pot body storage area has insulation layer,material is stainless steel matte plate control system microcomputer automatic control(manual/automatic) Application 1.Fruits: Apple, Banana, Pineapple, Peach, Cranberry, etc. 2.Vegetables: Carrot, Pumpkin, Snap bean, Sweet potato, Taro, Potato, Garlic, Green Pepper, Onion, etc. 3.Nuts: cashew nut, Peanut, etc. 4.Seafood, meat etc. Fish, shrimp, shellfish,chicken etc 5.Cooked wheaten food fried dough twist,crust of cooked rice,caramel treats etc Our Advantages 1.Low temperature fried, healthy food and low cost.It can prevent the loss of nutrients in the food at high temperature,effectively maintain the natural color and flavor of the food, and reduce the processing cost than the ordinary frying method. 2.Low oil content,good taste and no greasy. The oil content rate of food is below 15%. 3.Well stored and concentrated, the food is crisp and delicious 4.Rapid water evaporation and short drying time. 5.Safe, reliable and easy to operate. 6.Famous brand components. Electrical parts and operating parts are made of world advanced brand components. 7.Good expansion effect and high product rehydration 8.Long product shelf life. � Shandong Qinglei Environmental Technology Co.,Ltd is an equipment manufacturer integrating design, production and assembly. Our products include heat exchangers, heat exchange units, pressure vessels, storage tanks, TCU temperature control systems, reactors, distillation towers, VOCS purification and recovery systems, vacuum� frying machine. If you need any of them,please donâ??t hesitate to let me know,I will reply you ASAP.
TEMP WELDED FENCING IS MOBILE, REUSABLE, TENANTABLE & EASY TO ASSEMBLE A drawing picture of Canada temporary fence. CAF-01: Canada temporary fence Canada style temporary welded fence, also know as mobile fence, portable fence, is a kind of very popular temporary fencing in Canada and North America. The key feature of Canada mobile fence is the solid frame welded by square pipes, platy stable fencing feet and p shaped top coupler. Temporary fencing is a modular and steady system for isolation & protection work of construction sites, accidents scene, municipal engineering, commercial area, residential use. Regression, if you are a temporary fencing rental company, here is the one-stop choice for your requirement of durable and reusable. WHY CHOOSE US? 360° full welding by hand for highest strength. We own welding technicians all have more than ten years experience. The infill mesh and square pipe frame are welded smoothly and sturdily in 360° to prevent cracks and corrosion. Smooth surface and no burrs. All the weld pots are treated to eliminate all burrs on the surface to ensure the safe set up and tear down. Strong corrosion surface treatment. Electric galvanized before powder coated, the multi-layer anticorrosive treatment can effectively prevent the corrosion of acid rain and ultraviolet radiation. Hot dipped galvanized after welding, to ensure at least 70 μm thickness of zinc coating. Service life can reach more than ten years. Various colors are available. We can provide variety of colours by PVC coated surface treatment. Such as red, yellow, blue, gray, black, green, etc. One-stop supply system. Expect for fence panels, platy stable fencing feet, p shaped top coupler, foot screw (as needed) and shade clothes, other you wanted hardware can be supplied. Reliable and professional advice. As a company integrating production and sales, weâ??d like to give our customers a friendly and reliable advice for picking up the most suitable one for your desired application. Customized size for your needs. We have a standard size temporary fencing inventory. Beside, we accept customized orders of special panel length and height along with the pipe thickness and diameter. Free value-added service. Each container will be equipped with extra 20 clamps and 5 plastic bases for replacement.
OVERVIEWThis silicone is used for smooth fabrics like polyester, , swimwear base printing to improve adhesion and washing resistance. Usually it printed for first two layers or used for winter or golf gloves non-slip effect printing. It can be applied on automatic machine production with no mesh block.TYPICAL PROPERTYCode NO. T-J04ColorTransparentDurometer - Shore A31 Shore ADynamic Viscosity200000 CentipoiseElongation520 %Pot Life72 hoursShelf Life360 DaysSolids Content> 98 %Specific Gravity @ 25C0.95Tear Strength4.1MpaTensile Strength1015.3 psiPACKING Â 5kg/barrel; 20kg/barrelCLEANING After printing, silicone ink can be cleaned away from equipment with hydrocarbon based solvent.PRODUCT DISPLAYFAQ1.What is your MOQ?It depends on customer's exact request.2.Are you manufactuer or trading company?We are silicone ink and silicone heat transfer labels manufacturer, but we also do some trading based on customers trust.3.Where is your main market?Our main market based in Asian and south America countries where there are more printing factory for garments or shoes.4.What is your lead time?Normally in 3~15 days according to order quantity.5.What is your payment term ?T/T, Western Union, PayPalAFTER SALES1. All silicone base is mixed with 2-5% catalyst, too few or too much would affect the curing of silicone.2. Our silicone base can be mixed in proper rate to improve related functions.3. Our silicone is workable for both machine and table production which would not block mesh.4. Heating temperature of our silicone heat transfer stickers is 155~170â??, 15~20 seconds according to different fabrics and thickness.5. The order we delivered if its not match your request, pls keep it sealed well for replacement.PRINGTING QUESTION:Why should we use base-coating silicone ?Different silicone items has different viscosity and thickness which would affect its softness, adhesion, solid content. In this case, each item has its own advantages and disadvantage. Base-coating silicone perform well in adhesion and elasticity, which is very good to print bottom layer to improve fastness on some swimwear, polyester fabrics, elastic tapes.