TBK 2021 built-in double pump vacuum separator, heating and separating the mobile phone LCD screen frame and OCA glue removal Detailed Steps: 1. Turn on the power: Plug the power cord into the power connector on the back of the separator, and turn on the power switch. 2. Preset temperature: Press the SET button to preset the temperature, press the up button to set the temperature to about 85 degrees, and press NET to save. 3. Prepare the wire handle: equipped with a wire handle to separate the screen 4. Place the silicone non-slip mat: put it on the panel of the separator, align the rubber mat with the panel holes. 5. Screen separation preparation: Put the screen to be separated in the center of the panel, press the start key to start vacuum adsorption, and ensure that the screen is held. 6. Start cutting the screen: the screen is preheated for 3-5 minutes to start cutting. 7. After removing the bad screen, turn off the power of the separator. If it is dry glue, you can directly tear it off. If the water glue needs to be removed with the help of a blade and a glue removing solution. Features: 1. Can be used for straight screen or curved screen to remove glue LCD separation maintenance etc. 2. The heating table can rotate 360 degrees, the working temperature is 85â??, the highest temperature is 350â??, and the maximum support is 7 inches. 3. Built-in double vacuum pumps, strong suction, to ensure that the phone is firmly fixed. 4. Thermal insulation non-slip silicone pad, high temperature resistant insulation material ddoes not affect the suction, you can also choose not to use silicone pad 5.The heating platform is protected by a fuse to prevent burnout.
TBK 958M Mini Laser Back Glass Remover Auto Focus Engrave Laser Machine,TBK-958M Mini Laser Engraving Separation Machine for Smartphone Screen Dispaly and Rear Glass Replacement. TBK958M specification : Name :Fully Auto laser LCD screen remover ITEM NO: iLaser ultra Working voltage: 110V/220V Packing size: 400*200*500mm Product power: 500W Laser power: 6W Laser wavelength: 1064nm Marking accuracy: 0.001mm Marking speed: 10000mm/s Repeat accuracy : 0.001mm Marking area: 175mm* 175mm Marking depth: 0.015-0 5mm Marking line width: 0.05-0.01mm Applicaiton: Suitable for mobile phones, jewelry,handicrafts and other industries Description : TBK-958M Mini Laser Engraving Separation Machine for Smartphone Screen Dispaly and Rear Glass Replacement TBK-958M (mini) laser Engraving and Separating Machine 2021 Newest Designed Mini Sized Laser Engraving and Separation Machine for Smartphone Screen Dispaly and Rear Glass Replacement Small size 36.5*23*42cm, Light Net-weight 6.0 kgs; The max height of the engraved object is 55mm, and marking range 175Ã??175mm. Independently researching and developing the Optical path; Integrated-power mini laser, equipped with upgrading data in cloud; Imported sensor auto focus and imported high precision calibrator; External computer; one-button focus, one-button starts, simple operation.
Mijing K33 Pro 3 in 1 Face ID repair holder front facing camera repair fixture for Phone Dot Matrix repair tools, Face Lattice tin planting fixture support for Phone X XS XR XS MAX 11 11 Pro 11 Pro Max, MJ K33 Pro 3-in-1 for fix Phone Face ID not working, mobile phones face lattice repair fixtures for Phone XS XS MAX Phone 11 Pro Max. Mijing K33 Pro 3 in 1 Front Facing Camera Repair Holder Fixture For Phone Phones Face ID Not Working Mijing K33 Pro 3-in-1 Fixture : Repair the disassembly area / Chip IC repair area / Face Lattice tin planting area Product Features : Made of high quality durable material. Convenient to fix the soldering net. Specially designed for Phone X / XS / XS Max / XR / 11 / 11 Pro / 11 Pro Max / 12 Mini / 12 / 12 Pro / 12 Pro Max. Used to repair mobile phone motherboard IC chip. Make your repair work easier. We promised all products are new condition, but this item is easy to get scratched,there may be some scratches and fingerprint on the surface,please make sure you do not care before your order.
TBK-918 Smart Cutting And Grinding Machine for Phone Repair Cutting Tools Curved Screen IC Grinder Back Cover Glass Polishing,TBK 918 2in1 Intelligence Cutting Grinding Machine for Phone Repair,TBK918 intelligent cutting and grinding machine, mobile phone curved screen cutting, chip grinding all-in-one machine, high-precision adjustment, simple operation. Specification: Product model: TBK-918 Product voltage: 110-220V Product power: 100W Net weight: 6kg Gross weight: 8kg Features: Mobile phone maintenance intelligent cutting curved screen grinding chip all-in-one machine High precision multi-directional limit free adjustment high-speed aero motor Free switching between cutting and grinding, one machine for two purposes Cutting curved screen and polishing IC chip flexible switching Aviation brushless motor, high reliability, step-less variable, frequency speed regulation Low energy consumption and low noise Limit suspension cutting screen, flexible cutting of straight screen-curved screen multiple screens Multiple protection/Limit cutting piece/Safe and reliable Cutting multiple adjustments, adaptive to different heights, suspension limit cutting retine on Water bottle rack design, place water bottle, easy to catch water, not easy to fall Equipped with emery grinding head, precise grinding depth The proper amount of water can be adjusted, to reduce dust flying, increase cutting heat dissipation Stepless regulating motor speed The platform can tilt left and right, convenient for work Adjust fixed mobile phone Convenient for work Adopt a linear guide rail and add a bilateral stop block The water inlet can be connected outlet The motor can be adjusted left and right, and precise positioning
Aixun 2 in 1 Face ID Dot Projector Repair Fixture for Phone X XR XS MAX 11 12 Pro Max Product Application : Lattice maintenance separation and bonding Disassembly of the camera module and 3D fixed design Disassembly, assembly and maintenance of the front infrared camera The twisting magnetic ring clamp can adjust the tightness at will without hurting the dot matrix cable Applicable models X XS XS Max 11 11 Pro 11 Pro Max 12 Compact design, more suitable for operation under microscope Product Advantages : Aixun 2-in-1 Dot projector repair Jig Initiated repair jig / repair holder 2-in-1 design One is better than multi, with great compatibility, easy to repair . Powerful function, make the Dot projector repair easier and smoother. Multiple core functional advantages, all for better assisting you For separation and lamination of dot projector repair 3D fix design for camera module dismantling For front infrared camera dismantling repair The knob clamp for porcelain ring can adjust the tightness freely, avoid damaging to flex cable. Powerful function, make the Dot projector repair easier and smoother. Product Parameter : Item name: Aixun 2nd Gen 2-in-1 Dot Projector Repair Jig Brand: Aaixun Model: AX-J02 Color: Grey Net Weight: 50g Size: 76*311*23mm Applicable Models: X-12 * Above data are measured by Aixun Laboratory, please refer to the physical product. Package List : 1pc x Aixun 2 in 1 Repair Fixture
Automatic Instant 3 In 1 Coffee Stick Bag Powder Pouch Sachet Packing Machine This powder packaging machine can pack all kinds of powdery materials, using screw measurement method to avoid errors. Application The packing machine suitable for ultra-fine powder materials such as powder, flour, corn flour, milk powder, chili powder and soy flour. Specification Packing Speed: 30-80 bags/min Filling Range: 1-100 g Bag Size: Width:30-130 mm ; Length: 30-170 mm Film Width: Max.300 mm Power: 220 V, 50 HZ, 1.2 KVA Bag Type: Backside seal/3-side seal/4-side seal Machine Size: (L)1250 (W)950 (H)1920 mm (2.28 CBM) Horizontal Sealing: Netted Line / Straight Line(optional) Packing Material: Laminated film like OPP/CPP, OPP/CE, MST/PE/PET/PE Machine Texture: Carbon steel body and Stainless Steel 304 contact parts Accuracy: +/-1% Features 1.Made of stainless steel, rust and durable, easy operation and maintenance. 2.Controller by PLC, operate by touch screen, driving by stepper motor control. 3.Film moving very smooth and have sensor tracking, shape and dimension of bag is very well. 4.Horizontal and vertical sealing temperature can adjustable, better for lots of packaging film. 5.From filling, bagging, printing date, inflatable (exhaust) one-time completion. If you would like to get other information about the small powder packing machine,
Full Automatic Liquid Ketchup Tomato Sauce Paste Sachet Filling Packing Machine This liquid packaging machine can pack all kinds of liquids, and it can also be applied to liquids with poor fluidity. Application It is suitable for the packaging of various liquids and sauces such as liquid, sauce, soup, edible oil, liquid medicine, cream, seasoning sauce, honey, shampoo and shower gel. Specification Packing Speed: 30-80 bags/min Filling Range: 1-100 ml Bag Size: Width:15-110 mm; length: 30-180 mm Film Width: Max.220 mm Power: 220 V, 50 HZ, 1.2 KVA Bag Type: Backside seal/3-side seal/4-side seal Machine Size: 840(L) Horizontal Sealing: Netted Line / Straight Line(optional) Packing Material: Laminated film like OPP/CPP, OPP/CE, MST/PE/PET/PE Machine Texture: Carbon steel body and Stainless Steel 304 contact parts Accuracy: +/-1% Features 1.Different metering pump for different kinds of liquid. High accuracy and easy operation. 2.PLC intelligent chip computer system for efficient running. 3.Step motor for film drag structure, smooth film running and accurate bag cutting. 4.The touch screen, easy operation and multiple language for choice. 5.Separate PID temperature controller, suitable for various packing materials. 6.Articulated bag former structure, enable stable bag forming for perfect bag shape 7.Sophisticated sealing framework achieve the consistency of bag sealing and cutting. 8.Machine automatically finish the process of filling, metering, bag forming, sealing and packing. 9.Machine is simple operation, holding small space and easy moving. If you would like to get other information about the small vertical liquid packaging machine,
Radial Tire Special Material YB-5 Introduction: 1. JERINA YB-5 is a special material for radial tires, and a high-efficiency toughening modified agent that synthesized from various auxiliaries. It has plasticization, lubrication, cross-linking, coupling and other functions. 2. JERINA YB-5 also has high-activity inorganic filler as carrier, and the high-activity inorganic filler will dilute the toughening modified agent to form a thin layer of active material on the surface, which is more easily to crosslink with rubber, and significantly improve the reinforcing performance. 3. JERINA�® YB-5 mainly applicable to Tire, conveyer belt, rubber hose etc. Technical Specification: Appearance: White powder (visual inspection) Heating loss (105degX2h), % max.: 0.5 (HG/T2567) Specific gravity, g/cm3: 2.2-2.7 (HG/T3185) pH Value: 8.0-11.0 (HG/T2567) Application: 1. Add 3-8 phr JERINA YB-5 for tire production. 2. YB-5 can be added directly to your original formulation, or you also can make some small adjustment. Optimized vulcanization rate complies with test data and results. 3. Above are suggestions that you can adjust for optimal performance. Packing and Storage: 1. It is packed in Kraft paper bags lined with plastic film, net weight is 25kg/bag. 2. It should be stored in a cool, dry warehouse. 3. The shelf life is 24 months.
Rubber Antifatigue Agent LG-768 Introduction: 1. JERINA LG-768 agent consists of Non-metallic complex, Carbohydrate, Three-dimensional fiber grafted polymer, Non-metallic oxide and interfacial adhesive agent. The agent is a long-acting adhesion functional new material which produced by special technology. 2. JERINALG-768 agent is a Functional Additive for rubber and tire industry. It is non-toxic, harmless to human and no environmental pollution. Technical Specification: Appearance: Gray particles (visual inspection) Heating loss (105degX2h), % max.: 2.0 (HG/T3065) Ignition loss (800degX2h),% max.: 15.0 (HG/T3066) pH Value: 8.0-10.5 (HG/T3067) Performance: 1. JERINA LG-768 can improve the ageing-resistance and fatigue-resistance. The hindered phenol structure formed between phenolic hydroxyl group and methoxyl group on the molecule, which can capture and consume the free radical in rubber to terminate the chain reaction. Therefore, it can improve the ageing-resistance and fatigue-resistance of high polymer material such as rubber. 2. JERINA LG-768 can improve adhesive performance. It has excellent technologies. The new material has interfacial activity component, which can reduce the interfacial energy among all materials in formula. This will stabilize the dimension of rubber sheet and tires, and products surface will be smoother. Application: 1. Add JERINA LG-768 agent together with Zinc Oxide when mixing rubber master-batch. 2. 3~8 phr of total tire compound can be used for tire carcass, rubber sheet, rubber belt, and tire transition layer, other formula is same as before or make slightly adjustment. Packing and Storage: 1. It is packed in Kraft paper bags lined with plastic film, net weight is 25kg/bag. 2. It should be stored in a cool, dry warehouse. 3. The shelf life is 24 months.
Propylene Glycol Esters of Fatty Acid PGMS Characters: White powder or flake solid, insoluble in water, soluble in organic solvents such as ethanol, is a non-ionic emulsifier. Applications: Has excellent foam performance, good oil-soluble emulsifier. Used in pastry margarine, prevent the bread and confect aging, improve its processing performance. Uesd in ice cream, increase dilatability and shape preserving. Used in margarine to improve whipping, and to prevent the oil-water separate. Used for cakes, fried snack foods, complex sauce. Operation method and dosage: The max dosage for fat,oil and emulsified fat products is 10.0g/Kg, The max dosage for milk,dairy products and frozen drink is 5.0g/Kg, The max dosage for cake and fried foods is 2.0g/Kg, Technical index Acid value(Calculated by KOH)/ (mg/g) 4.0 Iodine value(g/100g) 3.0 Free Propylene glycol w/% 1.5 Hydroxide value(Calculated by KOH) / (mg/g)65 Saponification value(Calculated by KOH) / (mg/g)150-190 Soap(Calculated by Potassium stearate) w/% 7.0 Total mono ester content w/% 40 Ignition residue w/% 0.5 Pb / (mg/kg) 2 Packaging: Aluminized bag vacuum packing with nitrogen inside. Net weight: 20kg/carton(5kg/bag*4) Storage and transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and trasporting with materials that is explorsive, combustible or deleterious. The shelf life is 12 months.
Diacetyl Tartaric Acid Esters of Mono and Diglycerides Characters: Ivory or straw yellow powder or granular solid which is easily soluble in hot water. It is a non-ionic emulsifier with HLB value of 8-10. Applications: It can produce strong effects such as emulsification, dispersing and aging resistance, so it can be used as good emulsifier and dispersant. (1) It can increase the springiness, toughness and gas-holding capability of dough effectively, reduce its softening degree, increase volume of bread and steam bread, and improve their organization and structure. (2) It can react with amylose to delay and prevent the food aging. (3) It can be used in cream to make it smoother and finer. (4) It can be used in butter and concentrated butter to prevent oil separating and enhance its stability. (5) It can also be sued in sugar, syrup and spices. (6) It can be used in non-dairy creamer to make the emulsion homogeneous , stable and supple in mouth. Usage: (1) Put this product in warm water at about 60 C to get paste shaped substance, and then use it in appropriate proportion. (2) Dissolve this product in oils or fats homogeneously before further processing. (3) Directly mix it with flour for use. Recommended Addition Amount: Addition maximum is 1.0% for raw dried flour products and raw wet products, while 5.0% for non-dairy creamers. The addition amount can be changed based on production need for cream and fermented milk. Technical Index Acid value (Calculated by KOH) / (mg/g) 65-85 Saponification value (Calculated by KOH) / (mg/g) 390-450 Total tartaric acid(W/%) 10-40 Total glycerol(W/%) 11-28 Total acetic (W/%) 8-32 Free glycerol(W/%) 2.0 Ignition residue (W/%) 0.5 Pb/(mg/kg) 2 Packaging Aluminized bag vacuum packing with nitrogen inside. Net weight:20KG/CTN(5 KG *4) Storage & Transportation: Sealed and stored in the low temperature, dry, cool and well-ventilated place, in order to prevent from moisture and caking. Strictly forbid storing and transporting with materials that is explosive, combustible or deleterious. The shelf life is 12 months.
Inner tank: stainless steel SUS304/316L, thickness:1.0mm-1.2mm Outer tank: painted steel-0.4mm/aluminum-zinc coated steel-0.45mm/stainless steel SUS201/stainless steel SUS 304 Vacuum tube: QB-AL-N/AL-47-1500/58-1800 Insulation: 50mm-60 polyurethane Frame: coated galvanized steel-1.5mm/stainless steel SUS430-1.5mm/2.0mm aluminum alloy Accessories: intelligent controller, electric heater, magnesium bar, PT valve, negative valve etc. Characters: 1) Easy Maintenance No glycol, simple structure. No annual and periodical check-ups or maintenance is necessary. Blind sleeve design, no pollution, no-leaking heat pipe, easy installation. No water in vacuum tubes, one broken tube will not affect the function of the whole system. 2) High Performance With the cutting-edge vacuum-tube collecting technology, over 92% of sunshine energy is converted to thermal energy for heating and no circulation loss. Thicker insulation layer, functioning well in winter, even in minus-30-degree environment. 3) High Reliability System is simply working with the city net water, without pumps. Inner tank made by stainless steel SUS316-1.2mm. Working with high pressure, directly connected to running water, automatically functioning. With T/P valve and exhaust valve, it protects the tank from shrinking. 4)Year-round Operation With the freezing-proof technology, the system is designed and installed to operate for all seasons. Electric heater is optional to use, to ensure plenty hot water in rainy days. Principle: When vacuum tube absorb solar energy and heat the heat pipe ,the working fluid vaporizes and rise to the top of the heat pipe condenser, when heat pipe condenser meet cold water and cool down, the working fluid will fluidity and return to the bottom of the heat pipe, so once and once again to repeat this process.
General Description: 2D CNC Fully Automatic Wire Bending Machine is mainly used for bending and forming various metal wire into different shape in two-dimensional. The wire feeding and rotary bending system both adopt servo motor,significantly improves the precision of the product, and increases the speed and flexibility of machine effectively,furthermore greatly improves the production efficiency. According to the characteristics of wire processing, various kinds and shapes,we specially design the controlling system with a memory storage function,which can save more than 100sets of processing program for different products, can optionally select any one of them when needed. Main Features and Functions: 1.A full range of CNC Programmable wire bending machines for two-dimensional wire bending and forming, is manufactured according to European machine standards. 2.Heavy duty mechanical structures and minimum setup requirements due to reasonably design. 3.Friendly man-machine interface, user friendly programming, easy to operate. 4.Three groups of strong feeding-wire roller subassemblies powered with a servomotor ensure accurate wire feeding and excellent straightening. 5.Automatic wire straightening, feeding, forming and recording the output amount.The wire product size and parameters and presetting quantity,can also be changed and modified during producing. 6.Available for forming and bending different diameter of steel wire,iron wire, stainless steel wire, copper and aluminum wire,also other metals,which cross-section is round, flat, square, hexagonal, etc.Widely used in the industry of wire products, fan nets, handicrafts, lampshades,and so on.
Equipment Main Characteristics Our company established in 1995, has more than 10 years experience in making resistance welding machines and induction heating equipment. To meet the demand of heating needs, we developed the KIA-1KW mini induction heater with our partner This device adopt Electro-Magnetic induction theory, can fast heat small metal parts on auto or machines. Mainly used for heating Rusted/ Frozen/ Corrosive Bolt, Nut, Fasteners, Suspension Nut, Gears, Pulley, and Bearings etc. Meanwhile, it also can help removing stickers on cars. Heating Abilities: In around 30 seconds, it can heat a 20mm diameter bolt to a temperature above 300 C, maximum temperature can reach around 750 C. The advantage if using this device is it is totally flameless, comparing with traditional way of heating by fire, it is much safer and of higher work efficiency, without the worry of harming the adjacent area. Light weight, do not need water cooling, and very easy to use. Main technical parameters Model Number KIA-1KW Certificate CE(EMC,LVD),UL,CCC, Available for COC, POVC Rated Voltage 110V/220V AC 50/60Hz Rated Power 1000W Induction Coil Diameter Quantity 30mm2(PCS), 40mm 2(PCS), 50mm 2(PCS), Spare Wire 2(PCS) Heating Bolt Diameter 5-40mm Plug Type Type H, Type B, Type G, Type E Net Weight 1.3KG Heater Dimension 30cm 6.8cm 6.8cm
1. Taking out finished products after die cutting process,for waste stripping. 2. Applied for many die cutted product such as labels, hang tags, business cards, gift boxes, food boxes, paper cups and other die cutting products in paper or plastic, PU leather. 3. Two work heads: one inner hole cleaning + one stripping head 4. Rotary head of stripping to take out the opposite direction die cutting products easily . 5.Automatically taking out product with manipulator arm and stack product onto delivery belt. 6. PLC controlled with smart & easy operation. 7. Automatic lubrication system for machine better maintenance. 8. Different shapes can be custom-made as customer requirement Model:HTQF-1080CTR Machine Size: L4290xW2490xH2020 Max sheet size (X x Y) mm:1080 x 780 Min sheet size (X x Y) mm:650 x 450 Max pile height / mm:100 Work table height mm:850 Max product size to be punched out:390 x 390 Stripping speed times/min: 15-22 Manipulator Grip Range /mm:30-300mm Manipulator Grip Weight:50-1800g Max Power:5kw 380V Net Weight:3.2T Package Size:3700x1900x2200 Gross Weight: 3T
This commercial hot water heat pump is the best solution for hot water supply of commercial project, and can work with advantages of high safety, stability, much convenience, energy saving, and environment friendly, which assures 24 hours comfortable hot water using. It is widely used in hot water project of school, hotel, hospital, supper market and other large building, which needs large water volume supply. Commercial hot water heat pump series Model YINI-050S-RS Heating mode Circulating+Direct heat Ambient temp.range Rated heating capacity 18KW COP 4W/W Max. Running Current 9.7A Power supply 380V 3N 50Hz IP Code IPX4 Safety function High and low pressure protection, Overload protection, Temperature protection, Power phase sequence protection, etc. Refrigerant type/weight R407C/2.0kg Compressor QTY 1 PCS Compressor type Scroll Max. outlet water temperature 60 Water side heat exchanger type Casing/high efficiency tank Direct heat waterpipe nozzle G1 Internal thread (inch) Circulating waterpipe nozzle G1 Internal thread (inch) Air out type Top discharge Fan motor QTY 1 PCS machine dimension Packing dimension Net weight 130KG Gross weight 150KG Detailed Images Main Features 1) Copeland scroll compressor, quiet and high efficiency. 2) High efficiency heat exchanger. 3) 600 stage adjustment precision electronic expansion valve. 4) Schneider electrical components. 5) Intelligent controlling system. 6) Intelligent EE valve, excellent efficiency at different ambient temp. 7) Easy installation and LCD operation. 8) Automatically defrosting. Optional: R410a, R22, R407c refrigerant is available.
Swimming Pool Heat pump are specially designed and engineered for pool or spa water temperature control. Intelligent control system are let the units high efficiency and stable working performance. The COP could be 6.8 which saves at least 80% energy compared with traditional electric swimming pool heating equipments. Suitable for large pools in hotel, public parks, schools, sport center, gyms, etc. enter, gyms, etc. Wholesale Constant Temperature Heater Swimming Pool Heat Pump Main Features 1) PVC Titanium heat exchanger with full resistance against corrosion, more durable. 2) Compact structure, easy demountable for access. 3) High efficiency compressor, saving energy. 4) Flow switch for water flow protection. 5) Intelligent controller and adjustment by quick mind microprocessor. 6) Intelligent LCD display wired controller. 7) Air exchanger (fins-coil )with hydrophilic coating. 8) Automatic defrosting function included. Optional: R410a, R32, R407c refrigerant is available. Model YINI-010-YC Heating mode Circulating Ambient temp.range Rated heating capacity 7.8KW COP 6.7W/W Rated input power 1.15KW Max. Running Current 5.9A Power supply 220V-240V 1N 50Hz IP Code IPX4 Safety function High and low pressure protection, Overload protection, Temperature protection, Power phase sequence protection, etc. Refrigerant type R32 Compressor QTY 1 PCS Compressor type Scroll outlet water temperature 28 Heat Exchanger Titanium Air Flow Direction Horizontal Automatic defrosting by 4 way valve Casing Material ABS plastic Rated water flow 2.5 mh Air out type Top discharge Fan motor QTY 1 PCS Noise 56 dB(A) machine dimension Packing dimension Net weight 44kg Gross weight 55kg
1. Introduction With new materials and technologies, Improved Kam Chung magnesium oxide board has better performance and avoids the defects of traditional MgO board. We use an alkali-resisting glass fiber net to increase product strength, and new technologies to prevent the "crying" phenomenon. In that case, our products can be used in humid area and no need to worry about quality problem. 2. Application Kam Chung Magnesia board is light in weight, resistant to fire, high in strength, good against moisture, thus suitable for a wide range of general building uses, such as ceiling, wall board and flooring for residential complex, hospital, school, workshop, warehouse, stadium or even furniture and billboard. 3. Specifications Size (mm) 2440*1220 Thickness (mm) 3 -20 Moisture content (%) 8 Density (g/cm3) 0.6-1.4 Wet Expansion Rate(%) 0.6 Thermal Conductivity (W/mïK) 0.30 Bending Strength(MPa) 10 Shock Resistance (Kj/) 2 Dry Shrinkage Rate (%) 0.3 Nail-holding Ability (N/mm) 25 Content of Chloridion (%) 10 Non- combustibility GB 8624-2006 Class A Impermeability No water drops on the other side 4. Advantages (1). Durable (2). Fire rated (3). Insect-free (4). Waterproof (5). Light weight (6). Energy efficient (7). Impact resistant (8). Easy installation (9). Environment -friendly
3d  geotechnique  drainage  board  3d  geocomposite  drainage  compound  drainage  nets  manufacturer  Iso9001:2008  High  quality 3d composite drainage geonet introduction  Three-dimensional  composite  drainage  network  is  one  three-dimension  geonet  Composited  two  needle-punched  non-woven  geotextiles.  offering  completely  functions filter-drainage-protection ??.  this  kind  of  special  three-dimensional  Structure  can  make  it  bear  higher  compression  loading  and  keep  certain  thickness  And  same  time  offer  excellent  permeable  performance.    3d composite drainage geonet performance  1.  excellent  drainage  and  sustain  high  compression  loading 2.  highest  tensile  strength  and  shearing  strength 3.  cut  down  ratio  of  geotextile  into  geonet  and  keep  stable  permeability  in  a  long  time 4.  it  can  bear  compression  loading  over  2000kpa 5.Its  compressive  strength  far  exceeds  general  drainage  geonet  3d composite drainage geonet application  Using  for  drainage  such  as  refuse  landfill  roadbed  &  road  surface  railway  tunnel  underground  structure  retaining  wall  garden  sports  ground .
Specifications 1. Overhead insulated electrical cable astm/bs/din iec standard 2. Best price quality and package fast delivery Al/xlpe overhead abc cable (aerial boundled cable) single/duplex/triplex/quadruplex/five stranding. 1. Application of service drop cable: Service drop cable(abc cable) are mainly used for electric power transmission, rebuilding of urban and forest regions. They can improves safety and reliance of electrified wire netting. 2. Types of service drop cable: Service drop cable(abc cable) covers mainly three types: Duplex service drop triplex service drop quadruplex service drop 2.1 duplex service drop Applications To supply 120 volt aerial service for temporary service at construction sites, outdoor or street lighting. For service at 600 volts or lower at a conductor temperature of 75 maximum. 2.2 triplex service drop Applications To supply power from the ulility`s lines to the consumer`s weatherhead. For service at 600 volts or less(phase to phase ) at a conductor temperature of 75 maximum for pe insulation or 90 maximum for xlpe insulation. 2.3 quadruplex service drop Applications To supply 3 phase power, from a pole-mounted transformer to the use`s servic head where connection to the service entance cable is made. To be used at voltages of 600 volts or less phase to phase and at conductor temperature not to exceed 75 for pe insulated conductors or 90 for xlpe insulated conductors. Conductor standards: 1. B-230 aluminum wire, 1350-h19 for electrical purposes. 2. B-231 aluminum conductors, concentric-lay-stranded. 3. B-232 aluminum conductors, concentric-lay-stranded, coated steel reinforced (acsr). 4. B-399 concentric-lay_stranded 6201-t81 aluminum alloy conductors. 5. B498 zinc-coated steel core wire for aluminum conductors, steel reinforced (acsr). 6. Duplex service drop cable meets or exceeds all applicable requirements of ansi/icea s-76-474