Silicone Coated Paper Suppliers and Manufacturers

Addition Cure rtv-2 Liquid Silicone Rubber for Concrete & Stone moulds Artificial Stone & Concrete Casting Silicone Rubber Features: Amazing fluidity and easy to operate Platinum-based, food-grade silicone (environmental friendly, odorless -and non-toxic) Delicate design available Mixing ration: 1:1, easy to mix Easy de-molding Excellent tension and tear strength High performance in duplication Shrinkage is almost zero (below 0.1) Excellent resistance to weather, temperature, aging, acid and aging-proofing. High resistance to high temperature and aging(resist -60â?? to 250â??) Appearance: Part A:a non-toxic and odorless liquid with translucent color and platinum inside. Part B: a non-toxic and odorless liquid with translucent color. ATT: We can do any curing time as your requirements. Technical Data Characteristics of the non cured product Properties G-820 G-825 G-830 G-835 G-840 A B A B A B A B A B Appearance low viscous liquid Colour translucent Density [g/cm 3 ] at 23 �°C, approx 1.10 1.10 1.10 1.10 1.10 Viscosity [mPa�·s] at 23 �°C, approx 5000�±1000 6000�±1000 7000�±1000 8000�±1000 9000�±1000 Polymerisation Curing conditions: 1h at 80 �°C Properties G-820 G-825 G-830 G-835 G-840 Hardness Shore A 20�±2 25�±2 30�±2 35�±2 40�±2 Tensile strength [N/mm 2 ] 45�±10 50�±10 55�±10 55�±10 60�±10 Elongation [%] 500�±50 500�±50 450�±50 450�±50 450�±50 Tear strength [N/mm] 22�±2 24�±2 26�±2 24�±2 12�±2 Application: GC RTV silicone G-8 series are great for artificial stone casting. They are widely used for architectural elements, block-outs & hole former, concrete counter tops, flexible form liners, GFRC, manufactured stone veneer, ornamental precast & statuary, stamped & textured concrete, etc. Operation Method: Both pouring and brushing operation methods for our artificial stone casting silicone are available. You can choose the best one as your preference, we can provide thixotropic agent for brushing. Notice What is the hardness should I choose? Normally 20~40 Shore A will be the best, but it also should according to your size and pattern design. Warm Tips: The surfaces with which the material comes in contact must be perfectly clean, free of grease and dry. Close the bottles after use so as not to confuse the cap of the catalyst with that of the base when re-sealing. Be aware of possible cross-contamination; it's highly recommended to use only dedicated gear when processing poly-addition RTV2 silicone rubber (including degassing devices). Be aware that contact with certain material can inhibit the curing of the RTV2 poly-addition silicone rubber. Common contaminants to be avoided include: -Natural or synthetic rubber, vulcanized with sulphur derivatives. -Poly-condensation RTV catalyzed with metallic salts. -PVC stabilizing agents. -Amine cured epoxies. -Sulphur, tin and amines derivatives. -In case of doubt, carry out a small test by pouring the mixture onto a small area of the object.

The LCV series silicon cloth is a kind of cloth production which made based on fiberglass substrate through special processing. Because of its nice thermal conductivity, insulation and convenient assembly, it widely used in electronic appliances industry. When using, you should select different thickness of the thermal conductive silicon tape to cut according to the size of the fever interface and the height of the gap. Then putting the silicon tape in the gap between the fever interface and their components gap to play as a heat-conducting medium. Features & Benefits: Heat resistance, insulation, fire prevention, shock resistance Typical Applications: Heating power components Automobile electronic heating module Power module Household appliances Computer and peripherals, the filling and any place need heat dissipation between the heating element and the bottom plate.

LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact rita(at)szutd.com

High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact rita(at)szutd.com

China liquid Silicone mold making material for concrete/artificial stone casting Artificial Stone & Concrete Casting Silicone Rubber 1. Description C-825/C-830/C-835 Silicone Rubber is a two-part, tin-catalyzed, liquid silicone system that cures (RTV) to a white, Shore A25-A35 rubber. This is a pourable rubber, but it can be easily thickened with Liquid Thickener or for brush-on application. Popular product options is C-825/C-830/C-835 are the mold material of choice for high-volume veneer stone production (manual or automated manufacturing). These two-component mold rubbers capture excellent surface detail, offer exceptional dimensional stability and have unmatched lifetime and durability compared to hot melt and polypropylene systems. Molds made from these room temperature curing systems can be completed in a much shorter timeframe (~4 hour demold) compared to latex rubber molds. When properly maintained, these molds can last for years and produce thousands of stones. 2. Technical Datasheet Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3.Application

Characteristics 1.Calcium Silicon Barium Inoculant ( CaSiBa ) increase the graphitization core, refinement of graphite, promote get A type graphite from the Grey iron castings, increase the intensity, for ductile iron parts, it can make the graphite in ductile iron ball small, round, improve the nodulizing grade. 2.Calcium Silicon Barium Inoculant ( CaSiBa ) effectively reduce molten iron super-cooling degree, promote the precipitation of graphite, significantly reduce chilling tendency, reduce the relative hardness, improve casting machinability. 3.Calcium Silicon Barium Inoculant ( CaSiBa ) easy to dissolve and absorb than the average inoculant. can reduce the gascontent in the molten iron. 4.Calcium Silicon Barium Inoculant ( CaSiBa ) hight ability to recession-proof. at the same time it prevent relevant nodulizing decline, wall thickness sensitivity is small, well-closed formation. Standard GradeChemical Element (%) SiCaBaAlPS â?¥(Min)â?¤(Max) Ca10Si50Ba1350.010.013.03.00.050.05 Ca13Si45Ba1045.013.010.0 Ca11Si45Ba1345.011.010.0 Ca9Si45Ba1345.09.010.0 Ca7Si45Ba1545.07.015.0 Ca5Si45Ba1545.05.015.0 The specification,packaging and granular size can be produce according to customer demand.

Description of platinum curing mould making liquid silicone rubber Addition cure silicone is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 1:1 or 10:1. It can cure at room temperature as well as under heat. It's a kind of food grade silicone and mainly used for mold making. Application of platinum curing mould making liquid silicone rubber Silicone rubber is mainly used for making molds of tire, concrete stone, grc, polyurethane products; wax, candle decoration; rapid prototyping and tyre molds; chocolate, candy and similar products.

1.Unsaturated polyester resin, epoxy resins, polyurethane resins 2.Polyurethane elastomers 3.Natural and synthetic waxes 4.Plasters and cements Features of silicone rubber 1.Curing agent arrange together as free charged. 2.In liquid form and in various colors 3.With and exceptional fluidity and good operability 4.Temperature and deformation resistance as well as low shrinkage 5.High duplication times6.Samples orders are available 7.Moq:200kg Silicone rubber are generally named: Two-component room temperature vulcanization silicone rubber , a kind of elastic silicone rubber mold which features with resistance to deformation.High-temperature, acid-alkali and expansion, it mainly applicable to make the silicone mould for cultural relic duplication , architectural decoration, resin crafts , lighting ornaments , candles , statues mold design, product exploitation etc. Instruction for using silicone rubber for mold making to make molds. Step 1:preparing mold. Once you have your model to mould you need to build a box from wood/acrylic to contain the silicone and get a good covering over your model , the size and shape of this container is totally depends on shape of the model , remembering to leave plenty room surrounding the model so that you will have a strong wall thickness (at least 20mm) Note:small models can be cast in sourced containers like tins , ice buckets , cake tins, etc

Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey

Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Application: fiberglass mesh cloth Weight: 158 gsm - 1740 gsm Surface treatment: silicon coated Width: 300~600mm, 300~600mm w Eave type: plain woven yarn type: c-glass Alkali content: alkali free Standing temperature: -40?~260? Hardness: 70shore Specific gravity: 1.6~2.3g/cm3 Size: 50m/roll Thickness: 0.2~3.0mm Flammability: ul94v-0 Continuous use temp: -40?~260? Rohs: pass Color: pink, blue, grey

Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Type: insulation sheet, thermal pad Material: silicone, thermal conductive insulation pad Application: high voltage, cpu gpu Rated voltage: 4kv Tensile strength: 10.4mpa Color: blue Thickness: 0.1mm-10mm Feature: excellent resistance item Name: silicone rubber thermal conductive insulation pad Certificate: rohs Hardness: 20-50 shores Size: customizable

Description STS2200 insulating glass silicone sealant is a neutral curing silicone sealant with high modulus and high strength, purposely designed for glazing insulating glass. It has the advantage of low air permeability. STS2200 insulating glass silicone sealant works with two-component mixing equipment and the two components react quickly after mingled in scale, then cures to elastomer. Characteristics A.STS2200 belongs to rtv-2. It’s curing speed can be adjustable, and the deep-seated curing speed is fast, and it is suitable to be used in the factory; B. Neutral curing, non-corrosive to metal, coated glass etc. C. High modulus and high strength; D. Release low-molecular-weight alcohol and no unpleasant odor during cure; E. Excellent resistance to weather, uv, ozone, water; F. Remains flexible over a temperature range of-58°f(-50°c) to302°f(150° c) G. Good compatibility with other neutral silicone sealants. Applications As a secondary edge adhesive sealant in insulating glass units.

Compartment : 2 Container Tray, 4 Container Tray

Specifications : Capacity: 600 , 700 , 900 , 1000 , 1200 , 1400 , 1600 , 2100ml

Size : 6 MM X 197 MM 8 MM X 197 MM 10 MM X 197 MM

Material Rubber Color Black, Red, White, Green, Yellow Size/ Diameter 100 Meters Length of Pipe Water, Chemical,etc Elastomer Processors manufacturer & exporter of silicone rubber tube from size 0.2 mm ID to 200 mm ID with wall thickness from 0.2 mm to 10 mm as per customer requirement in all type of colour like REd, Black, White, Green, Orange, Blue, Yellow, Violet etc

SPK Customized MoSi2 heating element MoSi2 resistive heating element is a high temperature resistant and anti-oxidation resistance heating element based on molybdenum disilicide. When used in high-temperature oxidizing atmosphere, a layer of bright and dense quartz (SiO2) glass film is formed on the surface, which can protect the inner layer of the silicon molybdenum rod from oxidation, so the silicon molybdenum rod element has unique high-temperature oxidation resistance. Under oxidation atmosphere and the maximum service temperature is 1800 �¢??, the resistance of the silicon molybdenum rod electric heating element increases rapidly with the increase of temperature, and the resistance value is stable when the temperature is constant. Under normal conditions, the element resistance does not change with the length of service time, so the new and old silicon molybdenum rod heating elements can be mixed.