J series of 201 stainless steel | J1, J2, J3, J4, J5 J1: The carbon content is slightly higher than J4, and the copper content is lower than J4. Its processing performance is not as good as J4 material. It is suitable for ordinary shallow deep drawing and large angle deep drawing products such as decorative panels, bathroom products, sinks, and product pipes. J2, J5: Decorative tubes are easy to process, high hardness (both above 96�°), polished and beautiful, but they are easy to burst when used for square tubes or curved tubes (90�°). In terms of flat panel, due to its high hardness, the surface of the panel is more beautiful, and surface treatment such as frosting, polishing, and color plating can be carried out. But the biggest problem is bending, bending is easy to break, planing is easy to burst, so the ductility is not good. J3: High carbon, low chromium and low copper, but because of its high carbon content and low copper content, the material is slightly harder, so it is not suitable for bending with a slightly stronger strength. Compared with 201 stainless steel J1 material, the ductility is not so good, and it is easier to rust in the same environment. 201 stainless steel coil In the field of narrow bands, the emergence of 201 stainless steel J3 can better meet the requirements of pipe manufacturers for corrosion resistance and deformation. Because it can reduce the cost of raw materials for pipe manufacturers, it is sought after by pipe manufacturers in the narrowband field. J3 material is easy to process in veneer, but not difficult. The master of the processing factory said that he used J3 material to bend the board, and there would be an inner seam after it was broken (for black titanium, color board series, sanding board, when it is broken apart, there will be an inner seam when folding). The material of the sink has been bent 90 degrees, and it will not work if it continues. J4: The material of J4 is a relatively high-end variety in the J series of 201 stainless steel. It is suitable for deep drawing products with small angles. Most of the products that need deep drawing and salt spray test will choose it. Such as sinks, kitchen utensils, bathroom products, kettles, thermos cups, door hinges, pots, etc.
410 stainless steel is a stainless steel grade produced in accordance with American ASTM standards, which is equivalent to 1Cr13 stainless steel, S41000 (American AISI, ASTM). 0.15% carbon, 13% chromium, 410 stainless steel: good corrosion resistance, machinability, general purpose blades, valves. 410 stainless steel heat treatment: solution treatment (�¢??) 800-900 slow cooling or 750 fast cooling.Features: high strength; excellent machinability; hardening after heat treatment; magnetic; not suitable for harsh corrosive environments. 410 stainless steel is a type of martensitic stainless steel that contains 11.5-13.5% chromium and has excellent corrosion resistance, high strength, and hardness. It is a magnetic material and can be hardened through heat treatment, making it suitable for use in various applications that require high strength and corrosion resistance. Some of the key properties of 410 stainless steel include: Corrosion resistance: 410 stainless steel is highly resistant to corrosion, including water, steam, and chemical environments. However, it is not suitable for use in highly acidic or alkaline environments. Hardness: 410 stainless steel has high hardness and strength, making it suitable for use in applications that require wear and abrasion resistance. Heat treatability: 410 stainless steel can be hardened through heat treatment, allowing for improved strength and hardness. Magnetic properties: 410 stainless steel is magnetic and can be used in applications that require magnetic properties. Some of the common applications for 410 stainless steel include: Cutlery and kitchen utensils Valve components and pump parts Bolts, nuts, and screws Springs and bearings Medical instruments and dental tools Oil and gas equipment Overall, 410 stainless steel is a highly versatile material that is well-suited for use in various applications where high strength, corrosion resistance, and hardness are required. Here are some of the most common international standards for 410 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276: Standard Specification for Stainless Steel Bars and Shapes ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes JIS G4303: Stainless steel bars GB/T 1220: Stainless steel bars We can provide the following the form:410 stainless steel coil; 410 stainless stee strip;410 stainless stee plate; 410 stainless steel sheets; 410 stainless steel tubes; 410 stainless steel pipe;410 stainless steel flat; 410 stainless steel bar General blades, mechanical parts, tableware class 1 (spoon, fork, knife, etc.).
Stainless steel seamless pipe fitting : ASME B16.9 B16.11 B16.28 ASTM A403 SH3408 SH3409 SH3410 JIS B2311 B2312 B2313 B2316 DIN2615 DIN2616 DIN2617.
Product name: seamless stainless steel pipe Features: 1) commodity: seamless austenitic stainless steel pipe/tube, seamless duplex stainless steel pipe/tube, stainless steel u tube/pipe, bended tube/pipe, fin tube/pipe 2) process method: cold drawn/cold rolled 3) surface finish: anneal/pickling/manual polished/ mechanical polished 4) material: tp304/304l/h, tp309s, tp310s, tp316/316l/316h, tp317/317l, tp321/321h, tp347/347h, tp316ti, tp410/410s, tp409/409s, tp430, tp904l, 304, 304l, 321, 321h, 316l, 317l, 316ti, 347h, 310s, 904l, n08904, 2205, 2304, 2507, s31803, s32304, s32205, s32750, saf2205, saf2507, 1.4301, 1.4306, 1.4307, 1.4401, 1.4404, 1.4833, 1.4845, 1.4571, 1.4438, 1.4541, 1.4878, 1.4828, 1.4550, 1.4539, 1.4462, 1.4410, 1.4948, 1.4436, 1.4912, 1.4362, 1.4016, 1.4000, 1.4006, 08x18h12b, 03x17h14m2, 08x17h13m3t, 03x16h15m3, 03x18h11, 12x18h11t, 08x18h10t, 10x23h18, 12x17, 08x13, 12x13, sus329j3l and so on. 5) standards: astm(asme) (sa)a312/213/269/789/790/m, astm b677/b829, din 17456/17457/17458, bs en10216-5, jis g3459/3463/3448, gost 9941/9940, iso and so on 6) size: A) nps: 1/8" to 24" B) schedule: 5/5s, 10/10s, 20/20s, 40/40s, 80/80s, 120/120s, 160/160s, Acc. To ansi b36.19/36.10 C) O. D.: 6mm to 610mm D) w. T.: 0.5mm to 30mm 7) length: max. 25 meters 8) delivery conditions: annealed, pickling and polished 9) inspection: iso 9001-2000, ped 97/23/ec, tuv 10) applications: for fluid and gas transport, structure and machining Wooden box or non-woven fabrics.
stainless steel pipe&tube ANSI B36.19 O.D. W.T. Inch mm SCH5 SCH10 SCH40 SCH80 1/2" 21.34 1.65 2.11 2.77 3.73 3/4" 26.67 1.65 2.11 2.87 3.91 1" 33.4 1.65 2.77 3.38 4.55 1-1/4" 42.16 1.65 2.77 3.56 4.85 1-1/2" 48.26 1.65 2.77 3.68 5.08 2" 60.33 1.65 2.77 3.91 5.54 2-1/2" 73.03 2.11 3.05 5.16 7.01 3" 88.9 2.11 3.05 5.49 7.62 3-1/2" 101.6 2.11 3.05 5.74 8.08 4" 114.3 2.11 3.05 6.02 8.56 5" 141.3 2.77 3.4 6.55 9.52 6" 168.3 2.77 3.4 7.11 10.97 8" 219.08 2.77 3.76 8.18 12.7 10" 273.08 3.4 4.19 9.27 12.7 12" 312.85 3.96 4.57 9.52 12.7. Seaworthy wooden case.
Features: 1. Commodity: seamless stainless steel pipe/tube 2. Process method: cold drawn/cold rolled 3. Surface finish: anneal/pickling/manual polish/ mechanical polish 4. Material: tp304, tp304h, tp304l, tp310/s, tp316l, tp316/316l, tp316ti, tp317l, tp321/321h, tp410, s31803, s32750, 904l, 1.4301, 1.4306, 1.4401, 1.4404, 1.4541, 1.4571, 1.4438, 1.4539, 1.4845 and so on. 5. Standards: astm a312/213/269, astm a789/a790, astm b677, din17458, en10216 , etc. 6. Size: A) nps: 1/8" to 10" B) schedule: 5/5s, 10/10s, 20/20s, 40/40s, 80/80s, 120/120s, 160/160s, acc. To ansi b36.19/36.10 C) o. D.: 6 mm to 219 mm D) w. T.: 0.5 mm to 25 mm 7. Length: max. 20 meters 8. Delivery conditions: annealled, picklinged and polished 9. Packing: seaworthy wooden cases/steel framed cases/simple packaging 10. Certificate: iso 9001:2000, ped, tuv. Seaworthy wooden cases/steel framed cases/simple package.
Stainless steel pipe 1) grade: 304, 304l, 304h, 310s, 316, 316l, 316ti, 321, 321h, 347, 347h, 2) standards: astm a213m-94b, astm a249m-94a, astm a269-94a, astm a312m-94b, din 17456-85, din 17458-85, din 17459-92, jis g3446-1994, jis g3448-1997, jis g3459-1997, jis g3463-1994 3) size: A) o.D.: 1/8" to 12" B) w.T.: 2mm to 30mm 4) length: 1m to 13m 5) applications: fluid and gas transport, structure, boiler, heat exchanger, superheater ) grade: 304, 304l, 304h, 310s, 316, 316l, 316ti, 321, 321h, 347, 347h, 2) standards: astm a213m-94b, astm a249m-94a, astm a269-94a, astm a312m-94b, din 17456-85, din 17458-85, din 17459-92, jis g3446-1994, jis g3448-1997, jis g3459-1997, jis g3463-1994 3) size: A) o.D.: 1/8" to 12" B) w.T.: 2mm to 30mm 4) length: 1m to 13m 5) applications: fluid and gas transport, structure, boiler, heat exchanger, superheater
Product Name Precision Steel Pipe Standard DIN2391 EN10305-1 ASTMA179 ASTM A192 ASTM A519 Material SAE1010,SAE1020,#10,#20,#45,304,316 Outer diameter 8MM-50MM Wall thickness 0.5-50.0MM Length fixed(3-12m) or customized Technology High precision Cold drawn/ Cold rolled Heat treatment BK/BKS/NBK Advantages Short delivery time Quality assurance Competitive price
Product Name Precision Steel Pipe Standard DIN2391 EN10305-1 ASTMA179 ASTM A192 ASTM A519 Material SAE1010,SAE1020,#10,#20,#45,304,316 Outer diameter 8MM-50MM Wall thickness 0.5-50.0MM Length fixed(3-12m) or customized Technology High precision Cold drawn/ Cold rolled Heat treatment BK/BKS/NBK Advantages Short delivery time Quality assurance Competitive price
610*6.35
Carbon steel seamless tubes Standards Astmbsdin 1.A 1792.A 1923.A 210 ( gr.A1 / gr.C )4.A 333 ( gr.1 / gr.6 )5.A 334 ( gr.1 / gr.6 )6.A 335 ( t5, t11, t12, t22 )7.A 106 ( gr.B )8.A 213 ( p5, p11, p12, p22 )9.A 209 ( gr.T1 / gr. T1a )10.A 199 ( t5 )11.A 556 ( gr. C )1.3059 part û i gr. 320 2.3059 part - ii gr. 3603.3059 gr.4404.3602 part û i cfs 3601.2391 st-35, st -45, st û 52)2.2391 /c ( st-37.4, st -52.3, st-37.03.17175 ( st-35.8, st 45.8, 15 mo 3, 10 cr mo 910, 13 cr mo 44 ) Enis 1.10305 û 1 & 102042.10216 û 2 3.10287 û 1 1.1239 ( heavy, medium )2.3074 ( cds1, cds3 ) Straight tube : hdpe packing U tube : steel crate/wooden boxes
Carbon steel pipe/tube, erw pipe, large size pipe, gas cylinder pipe/tube, boiler tube with certification. O.D: 10mm---1200mm thickness: 1mm-70mm Standard: astm, jis, din, en, bs, iso, gb, api. Certificate: lr, gl, abs , dnv, bv , kr, nk, ccs Standard export packing
Seamless steel tube The main products of the company are the seamless steel pipes, using the advanced heat and cold processing technology, divides two kinds of hot rolling and cold draw. The raw materials are 10#~45# carbonized structural steel, the low-alloy steel, the bearing steel, and so on. The company can produce many kinds of seamless steel pipes of od 12mm~od70mm*wt2mm~wt13mm; od89mm~od168mm*wt4mm~wt20mm.
Seamless steel tube The main products of the company are the seamless steel pipes, using the advanced heat and cold processing technology, divides two kinds of hot rolling and cold draw. The raw materials are 10#~45# carbonized structural steel, the low-alloy steel, the bearing steel, and so on. The company can produce many kinds of seamless steel pipes of od 12mm~od70mm*wt2mm~wt13mm; od89mm~od168mm*wt4mm~wt20mm. ***
Seamless steel tube The main products of the company are the seamless steel pipes, using the advanced heat and cold processing technology, divides two kinds of hot rolling and cold draw. The raw materials are 10#~45# carbonized structural steel, the low-alloy steel, the bearing steel, and so on. The company can produce many kinds of seamless steel pipes of f+ 12mm~f+70mm*2mm~13mm; f+89mm~f+168mm*4mm~20mm.
Seamless steel tube The main products of the company are the seamless steel pipes, using the advanced heat and cold processing technology, divides two kinds of hot rolling and cold draw. The raw materials are 10#~45# carbonized structural steel, the low-alloy steel, the bearing steel, and so on. The company can produce many kinds of seamless steel pipes of f+ 12mm~f+70mm*2mm~13mm; f+89mm~f+168mm*4mm~20mm. **
Seamless steel tube The main products of the company are the seamless steel pipes, using the advanced heat and cold processing technology, divides two kinds of hot rolling and cold draw. The raw materials are 10#45# carbonized structural steel, the low-alloy steel, the bearing steel, and so on. The company can produce many kinds of seamless steel pipes of + 12mm+70mm*2mm13mm; +89mm+168mm*4mm20mm.
Stainless steel pipe.
Stainless Steel: ASTM A 312, A 213, A 249, A 269, A 358, A 240. Type: 202, 304, 304L, 304H, 316, 316L, 316Ti, 321, 321H, 317, 317L, 310, 310S, 409, 410, 420, 430 etc. Carbon Steel: ASTM A 106, A 53, API A 5L Gr A, B, C, ASTM A 333, Gr 1 to 6 (IBR & NON IBR). Alloy Steel: ASTM A 335, GR P1, P2, P5, P9, P11, P22, P91. Nickel Alloys: Hastelloy, 904, Titanium etc. Copper Alloys: Aluminium, Copper, Brass & Gunmetal. Types : Round, Square Rectangular. Size : Seamless: Upto 24" NB Welded: 1/2" NB to 60" NB All size, dimensions, grades & other specs as required.
Round hole stainless Perforated Metal Tube Perforated Metal, Metal Tube, Advantages of Perforated Metal Tube Perforated metal tubes are popularly used in filter products as support tubing and sometimes it is used directly as filter tube and cylinder for certain industries. We can manufacture perforated tube solutions with high tolerances and straight or flared ends to allow for unrestricted flow, facilitating flow pressure and temperature measurements. Construction of our tubes can include spiral or longitudinal welded seams or lock seams and you can choose any combinations from a selection of hole sizes and patterns. Micron opening perforated metal tubes are used as filters or screens itself in the screening of coal, gravel and ore; in the shifting and separation of food products, medical material, fine chemicals and oil. It is made of quality stainless steel or carbon steel sheets, perforated filter tubes and cylinders can be made spiral welded or butt welded in a wide range of sizes.
