SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Cable Television Communication Equipments Electric Power Systems Security Systems UPS systems Control Equipments Medical Equipments Emergency Power Systems Power Plant Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container. Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity. Specifications Nominal Voltage : 12V Capacity @ 20 HR : 12 AH Dimensions (mm)L : 150 Dimensions (mm)W : 98 Dimensions (mm)H : 95 Dimensions (mm)TH : 100 Battery Weight (Kg) : 3.6
FEATURES Excellent recovery from deep discharge. Gas recombination. AGM separator technology Lead calcium grid for Low self discharge No acid leakage from container and terminal Low maintenance operation. ABS container & cover PRODUCT APPLICATION UPS systems Solar System/Inverters Charging Fans Pathology Lab Equipment Electric Toys Lawn Movers Emergency Lights Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate. Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container. Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity. Specifications Nominal Voltage : 12V Capacity @ 20 HR : 7.2 AH Dimensions (mm)L : 152 Dimensions (mm)W : 65 Dimensions (mm)H : 100 Dimensions (mm)TH : 105 Battery Weight (Kg) : 2.5
FEATURES Designed for high performance vehicles with extreme high power demands High cold cranking ability at sub zero temperature Exceeds original equipments (OE) requirements PRODUCT APPLICATION 1000cc - 1300cc vehicles 1300cc - 1800cc vehicles Characteristics Instant Start & Excellent Dry Charge Performance Short pitch design for utmost performance during initial cranking of engine Special expander used for excellent starting at -15 C All car batteries are aluminum sealed Special separators are used to reduce the internal resistance Minimum water loss during usage of battery Repeated cranking performance without drop in capacity High Rate of Discharge characteristics compatible to the cranking current of the vehicle High Quality Polypropylene containers for long life of battery Specifications Nominal Voltage : 12V Capacity @ 20 HR : 40 AH No Of Plates : 11 Dimension (mm)L : 232 Dimension (mm)W : 132 Dimension (mm)H : 202 Dimension (mm)H with T : 222 Battery Weight IN KG : 8.50
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
The Dry Battery PTZ7L - 12V - 7Ah is a Valve Regulated Lead Acid sealed lead acid battery (referred to as VRLA) designed by AGM technology. AGM technology uses an Absorbed Glass Mat as a barrier; the electrolyte solution is absorbed at the plate, and the diaphragm is faster. Lead alloy composition and special additives suitable for starting purposes Advanced technology with an acid-free regulator valve, safe for users and vehicles. Outstanding advantages of the Dong Nai Maintenance-Free Dry Battery (VRLA) PTZ7A (12Vâ??7Ah) Specially designed for motorcycles. The most advanced technology for high performance, increased battery start-up, and service life Completely free of maintenance during use. Anti-shake design, suitable for all different terrain conditions.
1. Solar Home System Kits for off-grid application. 2. Kit contains a PV panel, Solar Charge controller, Lithium-Ion batteries or VRLA Gel batteries, wiring, connectors. 3. Optional PV panel mounting steel pole with brackets. 4. 4-8 nos of DC 12V 5 Watt or 9 Watt LED Bulbs, 2 Nos of 12V DC Ceiling or Table fans. 5. One USB port for mobile charging. 6. 8-10 hours back-up. 7. System customizable as per user requirements. 8. Easy to install, ideally suited for remote rural houses where grid is not available.
Product Name: Solar Power Battery Wifi Camera Resolution: 1280*960 (1.3mp) IR LEDs: 6pcs 850nm LEDs, Battery: 6800mAh Lithium Battery Storage: with TF Card Slot (support 8G/16G/32G/64G) Audio: built-in Mic for two-way audio function Connection: Wi-Fi (IEEE 802.11b/g/n 2.4GHz) Remote Monitoring: Smart Phone APP Record: Mobile APP Local Record and Device Record on TF Cards (start record once camera wake up) Camera Wake up: Wake up by Mobile Phone or PIR Push up time: normally push to mobile within 2 - 8 seconds Motion Detection: PIR Motion Detection, Sensibility Adjustable (high, middle, low), IP Grade: IP66 Weatherproof for Outdoor
6-GFMJ-20 FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 �°C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Uninterruptible Power Supply (UPS) Emergency Lightning Power Plants Telecom Backup Power Supplies Lawn & Garden Tools Gen set starting Auto Control Equipments Solar Energy Railway Signaling System Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity Specifications Nominal Voltage 12V Capacity @ 20 HR 20 AH Dimensions (mm) L 180 Dimensions (mm) W 76 Dimensions (mm) H 175 Dimensions (mm) TH 126 Weight KG 8.0
6-GFM-18 FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 �°C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Uninterruptible Power Supply (UPS) Emergency Lightning Power Plants Telecom Backup Power Supplies Lawn & Garden Tools Gen set starting Auto Control Equipments Solar Energy Railway Signaling System Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate. Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container. Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity. Specifications Nominal Voltage 12V Capacity @ 20 HR 18 AH Dimensions (mm)L 180 Dimensions (mm)W 75 Dimensions (mm)H 168 Dimensions (mm)TH 168 Battery Weight (Kg) 5.7
FEATURES Designed for high performance vehicles with extreme high power demands High cold cranking ability at sub zero temperature Exceeds original equipments (OE) requirements PRODUCT APPLICATION 660cc - 1000cc vehicles Characteristics Instant Start & Excellent Dry Charge Performance Short pitch design for utmost performance during initial cranking of engine Special expander used for excellent starting at -15 C All car batteries are aluminum sealed Special separators are used to reduce the internal resistance Minimum water loss during usage of battery Repeated cranking performance without drop in capacity High Rate of Discharge characteristics compatible to the cranking current of the vehicle High Quality Polypropylene containers for long life of battery Specifications Nominal Voltage : 12V Capacity @ 20 HR : 34 AH Number of Plates : 9 Dimension (mm)L : 195 Dimension (mm)W : 127 Dimension (mm)H : 200 Dimension (mm)H with T : 220 Battery Weight IN KG : 7
FEATURES Designed for high performance vehicles with extreme high power demands High cold cranking ability at sub zero temperature Exceeds original equipments (OE) requirements PRODUCT APPLICATION 1000cc - 1300cc vehicles Characteristics Instant Start & Excellent Dry Charge Performance Short pitch design for utmost performance during initial cranking of engine Special expander used for excellent starting at -15 C All car batteries are aluminum sealed Special separators are used to reduce the internal resistance Minimum water loss during usage of battery Repeated cranking performance without drop in capacity High Rate of Discharge characteristics compatible to the cranking current of the vehicle High Quality Polypropylene containers for long life of battery Specifications Nominal Voltage : 12V Capacity @ 20 HR : 40 AH Number of Plates : 11 Dimension (mm) L : 195 Dimension (mm) W : 127 Dimension (mm) H : 200 Dimension (mm) H with T : 220 Battery Weight (KG) : 8.25
he built-in MPPT can be charged with a Folding solar pane. The in-vehicle outlet can be charged. power station has one Pure Sine Wave AC outlets, It can power your full full-size refrigerator, TV, mini cooler, electric grill, fan, laptop, mobile phones and more for your outdoor and home needs.
What is Solar OFF-GRID system ? It works by generating electricity from solar panels and using it to charge a solar battery via a charger controller. That electricity is then converted using an inverter so that it can power the home or business appliances. By saving the electricity in a solar battery, it is possible to run home with solar energy, even at night or during times when there is less sun exposure. Description : We do SITC ( Supply , Installation , Testing , Commissioning ) of Solar Off-grid / Solar Hydrid systems from capacities ranging from 1 K.watt to 300 K.watt for all applications like Industrial , Commercial and Residential. We do deal with both Ground Mounted and Roof Mounted system installations. We design battery storage capacities after proper analysis of average load , load factor , maximum instantaneous power drawn , Depth of Discharge (DOD) , State of Charge ( SOC) , Thermal properties of battery and also provide proper ventilation for gases produced from batteries . We carry out Solar system installations all across India ( from Jammu Kashmir to Tamil Nadu and from Gujarat to Assam ) . Till time we extensively worked in states like Rajasthan , Maharashtra , Gujarat , Odisha , Uttar Pradesh , Madhya Pradesh , Karnataka , Tamil Nadu , Andhra Pradesh. Proper requirement analysis (energy consumption analysis) will be done and accordingly system will be designed by using proper design tools also considering proper load bearing and wind bearing capacities w.r.t. co-ordinates. Installation , Commissioning will be carried out by trained and certified team in professional way and within stipulated time. Safer installation will be done by providing proper protection systems , by proper cabling through conduits and also by providing proper earthing and lightning arresters . Round the clock service support is available & free quarterly service visits will also be provided. IOT ( Internet of Things) enabled Inverters will be provided and complete generation data can be viewed at your fingertips in mobile application . Even troubleshooting can be done over the air ( OTA) . We use only quality material of Tier 1 brands / Globally renowned brands only and offer our best solutions at all times . Facility of AMC for Solar plants is also available. Warranty of individual components : Solar panels will be coming with 15 years of warranty and upto 25 years of performance guarantee, which states percentage efficiency of generation would be greater than 90 % at the end of 15th year and will be greater than 80% at the end of 25th year Inverters comes with a standard warranty of 2-5 years depending on capacity of inverters. Same can also be extended upto 10 years. Solar Deep Cycle batteries come with a complete warranty (without any prorate calculations) ranging from 36 months to 60 months depending on the capacity of the battery
What is Solar OFF-GRID system ? It works by generating electricity from solar panels and using it to charge a solar battery via a charger controller. That electricity is then converted using an inverter so that it can power the home or business appliances. By saving the electricity in a solar battery, it is possible to run home with solar energy, even at night or during times when there is less sun exposure. Description : We do SITC ( Supply , Installation , Testing , Commissioning ) of Solar Off-grid / Solar Hydrid systems from capacities ranging from 1 K.watt to 300 K.watt for all applications like Industrial , Commercial and Residential. We do deal with both Ground Mounted and Roof Mounted system installations. We design battery storage capacities after proper analysis of average load , load factor , maximum instantaneous power drawn , Depth of Discharge (DOD) , State of Charge ( SOC) , Thermal properties of battery and also provide proper ventilation for gases produced from batteries . We carry out Solar system installations all across India ( from Jammu Kashmir to Tamil Nadu and from Gujarat to Assam ) . Till time we extensively worked in states like Rajasthan , Maharashtra , Gujarat , Odisha , Uttar Pradesh , Madhya Pradesh , Karnataka , Tamil Nadu , Andhra Pradesh. Proper requirement analysis (energy consumption analysis) will be done and accordingly system will be designed by using proper design tools also considering proper load bearing and wind bearing capacities w.r.t. co-ordinates. Installation , Commissioning will be carried out by trained and certified team in professional way and within stipulated time. Safer installation will be done by providing proper protection systems , by proper cabling through conduits and also by providing proper earthing and lightning arresters . Round the clock service support is available & free quarterly service visits will also be provided. IOT ( Internet of Things) enabled Inverters will be provided and complete generation data can be viewed at your fingertips in mobile application . Even troubleshooting can be done over the air ( OTA) . We use only quality material of Tier 1 brands / Globally renowned brands only and offer our best solutions at all times . Facility of AMC for Solar plants is also available. Warranty of individual components : Solar panels will be coming with 15 years of warranty and upto 25 years of performance guarantee, which states percentage efficiency of generation would be greater than 90 % at the end of 15th year and will be greater than 80% at the end of 25th year Inverters comes with a standard warranty of 2-5 years depending on capacity of inverters. Same can also be extended upto 10 years. Solar Deep Cycle batteries come with a complete warranty (without any prorate calculations) ranging from 36 months to 60 months depending on the capacity of the battery
Specification Shell type LFP51.2-400-MT-XDD Available electricity 21.094Kwh Rated capacity 400Ah Combination mode 16S2P BMS conifguration 16S400A Rated voltage 51.2V Operating voltage range 41.6V~59.2V Rated charge and discharge current 200A Peak current 400A Continue @410A 3s Rated charging and discharging power 10.24Kw Peak power 20.48Kw Continue @20.99Kw 3s Short-circuit current 0.8Ka@100us Cycle life 6000 Cycle 80%DOD, 25 Communication mode CAN, RS485 Parallel number No Remote data Bluetooth optional/Wifi Weight 170kg Dimensions (L*W*H) mm 585*280*1100mm Operating temperature Charging 0 ~+50 / Discharge -10 ~+60 Relative humidity 0~95% Storage temperature 3 Months -10 ~25 / 1 Year 0 ~25 Maximum working altitude 2000m Class of protection IP21 Supports inverter communication brands SMA/Growatt/TBB/Deye/GOODWE/Huawei/ Schneider/Victon energy/SOFAR/INVT Installation mode Floor mounting Power cable outlet mode Flank Standards and certification Transport UN38.3 *1 Test conditions, cell voltage 2.6V~3.65V, the new battery at +25 ±2 0.5C charging and discharging, available power may vary depending on the inverter; *2 Rated charge and discharge current and power will change due to temperature and SOC. If you have some problems about Gel Battery , or want to know more details about Storage Battery, LiFePO4 Battery, Uninterruptible Power Supply, Portable Power Station, Solar Power System, etc. Welcome to contact us! Pustunpower.com: lifepo4 battery 48v 51.2v, 50ah,100ah,150ah,200ah,300ah,400ah LiFePO4 Battery Pack Tags Lifepo4 Battery Manufacturers, Lifepo4 Solar Battery, Storage Battery manufacturers
MPPT Solar charge controller Feature 1. We choose high speed and high performance 32-bit processor with excellent EMC design 2. Advanced MPPT tracking algorithm, the tracking efficiency more than 99% 3. High performance IGBT power module as electronic switch, there is no any mechanical switch, plus multiphase synchronous rectification technology, improves the stable greatly 4. Ultrafast maximum power point tracking speed to ensure tracking efficiency 5. Accurate identification and tracking of multi-peak maximum power points 6. With current-limiting charging function, charging current can be set, friendly and compatible with various capacity batteries. 7. Widely PV arraysâ?? voltage input, this can save the cost of PV combiner box, wires and construction 8. Full enclosed duct design and high-speed fan for cooling makes the controller suitable for various harsh environment 9. It shows the ambient temperature. It also has automatic temperature compensation function and RTC real time function 10. The perfect battery protection function and multi-stage charging improves battery life 11. It has the statistical function of generating capacity which is very convenient for customers to view the daily, monthly and total charging capacity of the controller. 12. Complete menu display and operation, plus the humanized design of browsing interface, these makes the operation more easy 13. It can work with GEL. LEAD-ACID, LITHIUM and other type battery 14. Twice protection function to protect battery from damage when the power switch is down (optional) 15. Standard Modbus communication protocol for RS-485 or GPRS communication to extend the communication distance (optional function)
The SANDI solar charge controller adopts advanced digital control technology, touching keys and automatically operation. With the features of PWM (Pulse Width Modulation) battery charging and unique control technology, the PV charge controller improves battery life efficiently. The PV charge controller is only suitable for controlling solar modules. Never connect any other types of charging source to the controller. This can destroy the controller and/or the charging source permanently. To meet different solar power stations need, there are 48V 96V 120V192V 220V 240V 360V 384V 480V 492V and 600V other normal series voltage level base on different battery voltage of off-grid PV power station system project. Product Feature: 1, The solar controller uses high performance 32-bit chips which is excellent EMC design 2, The controller adopts advanced PID algorithm which has more accurate battery energy management system to improve the battery efficiency 45% at least 3, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 4, IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 5, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 6, The controller has double loop control function of voltage loop and current loop, user can set the limiting charging current 7, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 8, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 9, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. Users also can set working parameters through the LCD panel and touching keys according to different battery feature 10, The controller also has temperature compensation function and RTC real time clock function, 11, Standard Modbus protocol for RS-485 or GPRS communication to extend the communication distance (optional function) 12, The patent of second protection function which can protect battery from over charging due to power switch failure (optional function)
Size: : 430*310*250mm Voltage: 12.8V Weight: 30kg, 13.6g Nominal Capacity: 200Ah Application: EV,SOLAR,UPS Nominal Capacity (Ah): 200Ah Nominal Voltage (V): 12V Cell Specification: 3.2V 26650 3300MAH Rated Discharge Current (A): 30A Instantaneous Maximum (A): 100A