Lldpe Linear Low Density Polyethylene Suppliers and Manufacturers

V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

V6 Borewell Submersible Pumpset Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series - 60 feet head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Additional intermediate bearing in higher stage pumps - Fully SS pump set are available in SS - 304 Grade Specification - Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. - Speed : 2900 RPM - Head Range : 12 Mtr. To 600 Mtr. - Discharge Range : 1080 LPM to 170 LPM - Outlet Size in Inch : 2.0, 2.5 , & 3.0 - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

HDPE Blue Drum Regrind consists of HDPE regrind from blue drums scrap (Extrusion Grade Blow Moulding Grade). Cold Washed Clean without any contamination. Packed in jumbo bags for easy loading. We have convenient trade terms and the fastest delivery schedules. what is advantage of hdpe? This strengthening with its UV-resistance makes it ideal for piping and outdoor applications. Pipe grade sheet has the ability to withstand -220 to 180 degrees Fahrenheit. It�¢??s durable in most chemical interactions which make it useful in a lot of industrial applications. HDPE drums regrind 1.Hot water washed and no label, no any contaminant 2.dry and clear flakes 3.white,blue, red, yellow and so on 4.from crates, drums, pallets 5.MFI 0.03-0.1 Specification HDPE Blue Drum Regrind ITEM STANDARD Melt Flow Rate(g/10min) 0.1 Density(g/cm3) 0.95 Power Ash% 0.01 Tensile Strength(MPa) 22 Elongation At Break% 600 Environmental stress-cracking 1500 We are leading trading company, suppliers/exporter of best grade Plastic scraps in South Africa. We are one of the largest exporter of Plastic Scraps. We provide top grade quality to our Buyers. hdpe blue drum price There are several suppliers in the market with each supplier with their own price. The price varies between $300 and $500 per ton . At vitameta ltd we offer best price on bulk order purchase SPECIFICATION: Plastic Scraps Products PET Bottles Scrap LDPE Film Scrap PET Flakes Scrap HDPE Scrap Unvulcanised Rubber Scrap PET Film Rolls ABS Scrap PP Raw Materials EPS Block Scrap E-Waste Products: PVB film scrap LDPE rolls Baby Diapers PU Foams HDPE Granules Our HDPE Blue Drum Flakes are high in quality and relatively low price. We wish to make a long term scrap business deal with reliable and stable Plastic Scrap buyers from all over the world. Interested Plastic Scrap buyers, please contact us today for scrap prices and further details. We are waiting to hear from you soon. Thank you for your time. We offer products like Hdpe Milk Bottles Scrap, Hdpe Milk Bottle Regrind, Virgin Hdpe Granules / Recycled Hdpe Granules, Hdpe Blue Drum Regrind, and Blue PC water Bottle Scrap 99.99% Pure. We are wholesaler dealers of HDPE Blue Drum Regrind, HDPE blue drum flakes supplier. Adding to that We grind HDPE plastic, scraps and sell them domestically and Internationally. Furthermore, We can separate the regrind by color if you want that. Below are some of our HDPE regrind. Moreover, They are ground from crates, barrels, buckets, lids, pipes, plates, bottles and others. Lastly, We sell HDPE CLEAR/NATURAL REGRIND (CLEAN AND WASHED) contact us.

Basic Info. Model NO. LFP51.2-300 Electrolyte LiFePO4 Color White Usage Solar/ Marine/ Telecom / Electric Mobility Warranty 3 Years OEM/ODM Acceptable Package Carton and Pallet Lead Time 20-30 Days Dimension 720*260*580mm Transport Package Wooden Case Specification 120kg Trademark PUSTUN Origin China HS Code 8507600090 Production Capacity 5000 Product Description Product Description Factory Wholesale Deep Cycle 51.2V300ah Lithium Ion Batteries LiFePO4 Lithium iron phosphate battery is a kind of lithium ion battery that uses lithium iron phosphate (LiFePO4) as the positive electrode material and carbon as the negative electrode material. It has the advantages of high working voltage, high energy density, long cycle life, good safety performance, low self-discharge rate and no memory effect. Pustun lithium iron phosphate battery is your best power choice for energy storage system of solar street light. This LFP series battery is specifically designed for solar street light application, which has more than 10 years service life; LFP series batteries are the best choice for the durable, safe, environment-friendly energy solution and they can be customized according to your requirement, such as dimension, voltage, capacity of battery. With an increased lifespan, this battery can save you much cost against frequent battery replacement. The working life of lithium battery especially under the outdoor high temperature environment is five times longer than the traditional lead acid battery. Product Parameters Nominal Voltage 51.2V Nominal Capacity 300Ah Energy 15.36KWh Combination mode 16S1P Cycle Life â?¥6000 Cycle, 80%DOD, 25�ºC BMS conï¬?guration 16S150A Operating voltage range 41.6V~59.2V Rated charge and discharge current 150A Peak current 160A Continue @170A 3s Rated charging and discharging power 7.68Kw Peak power 8.192Kw Continue @8.704Kw 3s Short-circuit current 0.762Ka@100us Communication mode CAN, RS485 Parallel number Recommend 6 in parallel(Maximum support 16 in parallel) Remote data Bluetooth optional/Wiï¬? Weight 120kg Dimensions (L*W*H) mm 720*260*580mm Operating temperature Charging: 0�ºC~+50�ºC / Discharge: -10�ºC~+60�ºC Relative humidity 0~95% Storage temperature

Basic Info. Model NO. LFP25.6-100 Electrolyte LiFePO4 Color White Usage Solar/ Marine/ Telecom / Electric Mobility Warranty 3 Years OEM/ODM Acceptable Package Carton and Pallet Lead Time 20-30 Days Dimension 750*145*250mm Transport Package Carton Specification 28kg Trademark PUSTUN Origin China HS Code 8507600090 Production Capacity 5000 Product Description Product Description 25.6V100ah Renewable Energy Lithium Ion LiFePO4 Battery Lithium iron phosphate battery is a kind of lithium ion battery that uses lithium iron phosphate (LiFePO4) as the positive electrode material and carbon as the negative electrode material. It has the advantages of high working voltage, high energy density, long cycle life, good safety performance, low self-discharge rate and no memory effect. Pustun lithium iron phosphate battery is your best power choice for energy storage system of solar street light. This LFP series battery is specifically designed for solar street light application, which has more than 10 years service life; LFP series batteries are the best choice for the durable, safe, environment-friendly energy solution and they can be customized according to your requirement, such as dimension, voltage, capacity of battery. With an increased lifespan, this battery can save you much cost against frequent battery replacement. The working life of lithium battery especially under the outdoor high temperature environment is five times longer than the traditional lead acid battery. Product Parameters Nominal Voltage 25.6V Nominal Capacity 100Ah Energy 2.56KWh Combination mode 8S1P Cycle Life â?¥6000 Cycle, 80%DOD, 25�ºC BMS conï¬?guration 8S100A Operating voltage range 20.8V~29.6V Rated charge and discharge current 100A Peak current 100A Continue @120A 3s Rated charging and discharging power 1.28Kw Peak power 2.56Kw Continue @3.072Kw 3s Short-circuit current 0.225Ka@100us Communication mode CAN, RS485 Parallel number Recommend 6 in parallel(Maximum support 16 in parallel) Remote data Bluetooth optional/Wiï¬? Weight 28kg Dimensions (L*W*H) mm 750*145*250mm Operating temperature Charging: 0�ºC~+50�ºC / Discharge: -10�ºC~+60�ºC Relative humidity 0~95% Storage temperature

V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5

Item No.: 2058-28 Size: 39-46 (5-12) Soles : 2058 Mono Density PU ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Combat Boot Standard : S1 Sizes : 39-46 (5-12) Colors : Black ADDITIONAL PRODUCT INFO OVERVIEW Product Name: Combat Boot Standard : S1 Sizes : 39-46 (5-12) Colors : Black MATERIALS Upper : Buff Softy/light Haircell Lining : Cambrella TOE: Soft toe Footbed / Socks: Moulded Sole : Single Density PU Certified : EN ISO 20345:2011 Boot Care * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and com

Item No.: 2059-04 Size : 36-40 (6-9) Soles : Mono Density PU ADDITIONAL PRODUCT INFO OVERVIEW Product Name: Safety Shoe Standard : S1 SRA Sizes : 36 - 40 (6-9) Colors : Black AVAILABLE OPTIONS Product Number: 2059-04 Standard: S1, S1p, S2, S3 TOE: Steel Midsole: 36-40 Sole : Mono Color: Black / Brown MATERIALS Upper: Haircell Smooth Lining : Cambrella TOE: Steel Midsole : Single Density PU Footbed / Socks: Moulded Antistatic Sole : Single Density PU Certified : NA BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.

Item No.: 2059-01 SSBA (LADIES) Size: 36-40 (6-9) Soles : Mono Density PU ADDITIONAL PRODUCT INFO OVERVIEW Product Name: Safety Shoe Standard : S1 SRA Sizes : 36 - 40 (6-9) Colors: Black AVAILABLE OPTIONS Product Number: 2059-01 Ssba (ladies) Standar : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Mono Color : Black / Brown MATERIALS Upper : Haircell Smooth Lining : Rice Knit Mesh Toe : Steel Midsole : Single Density Pu Footbed / Socks: Libactive Antistatic Sole : Single Density PU Certified : NA BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions

Item No.: 2058-06 Size : 39 - 46 (5-12) Soles : 2058 Mono Density PU SAFETY FEATURES Abrasion Resistant Acid Resistant Anti Static Insole Excellent Shock Absorber Fine Leather Light Weight Slip Resistant Sole Steel Toe Cap ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Safety Shoe Standard : S1 Sizes : 39 - 46 (5-12) Colors : Black AVAILABLE OPTIONS Product Number: 2058-06 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Mono Color : Black / Brown MATERIALS Upper : Water Repellant Buff Waxy Lining : Soft Buff Leather Toe : Steel Footbed / Socks: Padded Antistatic Sole : 2058 Mono Density PU Certified : EN ISO 20345:2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and co

Item No.: 2058-11 Size : 39 - 46 (5-12) Soles : 2058 Mono Density PU SAFETY FEATURES Abrasion Resistant Acid Resistant Anti Static Insole Excellent Shock Absorber Fine Leather Light Weight Oil Resistant Slip Resistant Sole Steel Toe Cap Water Proof ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Safety Shoe Standard : S2 Sizes : 39 - 46 (5-12) Colors : Black AVAILABLE OPTIONS Product Number : 2058-11 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Mono Color : Black / Brown MATERIALS Upper : Water Resistant Smooth Haircell Lining : Soft Buff Leather Toe : Steel Midsole : Steel Footbed / Socks : Cambrella and EVA. Antistatic Sole : 2058 Mono Density PU Certified : EN ISO 20345:2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.

Item No .: 2080 - 62 Size : 36 - 47 (5-13) Soles : 2080 Dual Density PU SAFETY FEATURES Abrasion Resistant Acid Resistant Anti Static Insole Excellent Shock Absorber Fine Leather Light Weight Oil Resistant Slip Resistant Sole Steel toe / Kavlar Steel Toe Cap ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Safety Boot Standard : S3 Sizes : 36 - 47 (5-13) Colors : Black AVAILABLE OPTIONS Product Number : 2080 - 62 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Dual or Mono Color : Black / Brown MATERIALS Upper : Water Resistant Nubuck Lining : CAMBRELLA 100% polyamide, Breathable, absorbing and releasing moisture, Abrasion Resistant , Odour free, Toe : Steel Midsole : Steel Footbed / Socks : Felt Antistatic Sole : 2080 Dual Density PU Certified : EN ISO 20345: 2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.

Item No .: 2080 - 68 Size : 36 - 47 (5-13) Soles : 2080 Dual Density PU SAFETY FEATURES Steel Toe Cap Oil Resistant Shock Absorber Anti Static Insole Anti Skid ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Safety Shoe Standard : S1 Sizes : 36-47 (5-13) Colors : D Grey AVAILABLE OPTIONS Product Number : 2080-68 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Dual Or Mono Color : D Grey / Blue / Tan MATERIALS Upper : Water Repellant Nubuck, Suede and Breathable Textile Lining : Textile, Breathable, Absorbs and Release moisture, Abrasion Resistant Toe : Steel Footbed / Socks : Padded Antistatic Sole : 2080 Dual Density PU Certified : EN ISO 20345: 2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.

Item No .: 2080 - 150 Size : 36 - 47 (5-13) Moq : N/A Soles : 2080 Dual Density PU SAFETY FEATURES Anti Skid Anti Static Insole Oil Resistant Shock Absorber Steel Toe Cap ADDITIONAL PRODUCT INFO OVERVIEW Product Name : Safety Boot Standard : S1 Sizes : 36 - 47 (5-13) Colors : Grey AVAILABLE OPTIONS Product Number : 2080 - 150 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Dual or Mono Color : As Per Pic MATERIALS Upper : Water Repellant Nubuck, Suede and Breathable Textile Lining : Textile, Breathable, Abdosrbs and Release moisture, Abrasion Resistant Toe : Steel Footbed / Socks : Moulded Cambrella and EVA. Antistatic Sole : 2080 Dual Density PU Certified : EN ISO 20345: 2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.

Item No. : 2080-181 Size : 36 - 47 (5-13) Moq : N/A Soles : 2080 Dual Density PU SAFETY FEATURES Abrasion Resistant Acid Resistant Anti Static Insole Excellent Shock Absorber Fine Leather Light Weight Slip Resistant Sole Steel toe / Kavlar Steel Toe Cap ADDITIONAL PRODUCT INFO OVERVIEW Product Name: Safety Boot Standard : S1P Sizes : 36 - 47 (5-13) Colors : Black AVAILABLE OPTIONS Product Number : 2080-181 Standard : S1, S1P, S2, S3 Toe : Steel Midsole : Steel Sole : Dual or Mono Color : Black / Brown MATERIALS Upper : Water Repellant Nubuck Lining : Textile, Breathable, Absorbs And Release Moisture, Abrasion Resistant Toe : Steel Midsole: Steel Footbed / Socks : Cambrella And Eva. Antistatic Sole : 2080 Dual Density Pu Certified : EN ISO 20345:2011 BOOT CARE * Clean your footwear regularly using high quality products that are suitable for the cleaning purpose. NEVER use caustic or corrosive cleaning agents. * When footwear is not in use clean the sole and store in a well-ventilated area. Never store the footwear underneath heavy items or in contact with sharp objects. If the footwear is wet allow it to dry slowly and naturally away from direct heat sources before storage. * To put on and take off footwear always fully undo fastening systems. Use a shoe horn to wear shoes. Only wear footwear of a suitable size. Products which are either too loose or too tight will restrict movement and will not provide optimum levels of protection and comfort. * The shoe should be used for the purpose for which it has been designed. Some facts about feet- * Most of the muscles are in your feet. Thus you should wear comfortable shoes. * The body temperature is regulated through your feet * Maximum number of nerves go through your feet. 100% COMFORT GUARANTEED * Quality leather upper and high quality breathable lining materials are used for proper air circulation in shoe for keeping the feet cool and odour free. * Construction of lasts based on extensive survey enabling the lasts/shoes to be manufactured for better fit providing maximum comfort. * Wider Steel and Ultra light Weight Composite Toe caps which provides more room for finger movements enhancing comfort. * Cushioned Insoles providing better comfort. * Shock absorbing PU midsole with low density providing uniform cushioning and comfort. * Light Weight PU for a featherlite feel even during high stress working conditions.