United Photonics Technology Waveplates Principle Application 4 Waveplate UPT quarter waveplates create a quarter-wavelength phase shift 2, 90 and can convert linear polarization to circular polarization and vice versa. They are often used with a linear polarizer to form an isolator, blocking light reflected back from other surfaces (ellipsometry, optical pumping, isolation). UPT half waveplates retard one polarization direction by half a wavelength 180, effectively changing the direction of linear polarization, depending on the orientation of incident linear polarization with respect to the crystal axis. Therefor they can be used as continuously adjustable polarization rotators e.g. in electro optical modulation or as a variable beam splitter when used in combination with a polarizing beam splitter. Achromatic Waveplate Unlike standard waveplates, Achromatic Waveplates, provide a constant phase shift independent of the wavelength of light that is used.This wavelength independence is achieved by using two different cr.. Zero Order Waveplate-Cemented by Epoxy The zero order waveplate is designed to give a retardance of zero full waves, plus the desired fraction. Zero order waveplate shows better performances than multiple order waveplates, it has broad ban.. Zero Order Waveplate-Optically Contacted Optically Contacted zero order waveplate is constructed by two quartz plates with their fast axis crossed, the two plates are constructed by optically contacted method, the optical path is epoxy free... Zero Order Waveplate -Air-spaced Air spaced zero order waveplate is constructed by two quartz plates installed in a mount, to form a air gap between the two quartz plates. The difference in thickness between the two plates determines.. True Zero Order Waveplate Broad Spectral Bandwidth Wide Temperature Bandwidth Wide Angle Bandwidth Cemented by Expoy Specifications: Material: .. Low Order Waveplate Multiple order waveplate means the retardance of a light path will undergo a certain number of full wavelength shifts in addition to the fractional design retardance. The thickness of multi order wave.. Dual Wavelengths Waveplate Single retardation plate Dual-wavelength AR coated, R0.2% foundational wavelength R0.5% SHG wavelength Specifications Material: ..
Test-630 is a six phase current output and six phase voltage output protection relay tester with 5.Eight pairs of binary input and four pairs of binary output FEATURES Integration in the host crystal 8.4 inches true color, light weight and easy to carry. Built-in high-speed and high-performance industrial computer embedded operating system, running stable and reliable, also can test by connecting PC. Panel embedded user-friendly buttons, and the panel can also be an external keyboard and mouse. High-precision DAC to 12 Road, simultaneously output to ensure the high precision and good linearity of the waveform. 5Matching electromagnetic compatibility components, can improve on-site anti-electromagnetic interference, protection devices can connect the electromagnetic compatibility to test. Analog output of the front panel, switch the amount of terminal design in the upper cover, all the wiring does not affect the operation of the panels and the test parameters of the surveillance. The latest thermal structure design to ensure the best ventilation. Automatically determine over current, over voltage, overload and short circuit, if the temperature is too high, the anomalies and misuse warning of the data will show up promptly. Using voltage, current amplifier AC / DC sharing, output stage uses a unique ultra-linear amplifier technology, high precision and reliability. six-phase AC output voltage and six-phase AC current. 12 analog ports and other optional auxiliary DC source output (220V/110V). Interface: RJ45 (Ethernet interface), USB interface (software upgrades, reporting transmission), industrial serial interface (GPS or other serial device use). TEST ITEM U/I Test DC Test Impedance Characteristics Power Direction Test I-T Test Differential Relay Harmonic Test Differential Protection Distance Protection Zero Sequence Protection Setting Group Test State Sequence Synchronization Test Special Test Oscillation Test Metering Instrument Hardware Checkout Low Voltage Protection Fault Recurrence
The best sport headphones built with high-performance speakers for extended frequency range, lower distortion. High performance and noise isolating ear tips eliminate ambient noise. These high definition stereo high quality earbuds provide the excenllent sound input& output quality that produce incredible natural high fidelity sound with deep bass and crystal clear treble . Ergonomic earbud design, these acoustic noise cancelling headphones will fit comfortably in ears while gym training, traveling, dancing or hiking. No need to stop your workout to adjust the Earphones anymore. high quality earbuds deliver deep, clear sound for the music you love, and a durable design to keep up with whatever your day brings . when you run with the best sport headphones in they do not come loose or fall out and you can enjoy awesome quality sound at the same time . you can play, pause, skip tracks and volume up/down from the remote buttons on the right ear cable. You can enjoy a wide variety of music ranging from classical piano, rock, pop, oldies, to heavy metal with this acoustic noise cancelling headphones and the sound quality is superb. Looking for ideal Best Sport Headphones Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the High Quality Earbuds are quality guaranteed. We are China Origin Factory of Acoustic Noise Cancelling Headphones. If you have any question, please feel free to contact us.
yinuolink industrial din rail gigabit ethernet switch Description YN-IES10503 is a type of unmanaged industrial Ethernet switch with 5 port 10/100/1000Base-T(X ) Ethernet port , supports IEEE802.3, EEE802.3u standard, support positive and negative DC input protection to prevent burnout. With no fan and low power consumption design, IP40 grade protection ensures reliable work in harsh environment. LED indicator is helpful to monitor the status of network connection. DIN rail installation and wide operating temperature (-40~+75â??),it fulfil the industrial working environment, can provide reliable and quickly solution for your Ethernet device. Advantages 1. Adopt 5 ports industrial grade imported chips 2. PCB using TG180 imported PCB material,Immersion gold craft and antioxidant ability will be good 3. Crystal use Japanese Kyocera brand, support -40~+125°C 4. Ethernet port is gold-plated 1.5U, itâ??s also very stable with many time plugs 5. DC to DC power IC using imported MPS, maximum support 12-48V 6. Capacitors all made by Murata Japan Features 1. Support 5 port 10Base-T/100Base-TX/1000Base-TX Ethernet 2. Support IEEE802.3/802.3u store and forward 3. Support Ethernet 10/100M self-adaption 4. 12~48VDC wide voltage power supply input 5. No fan, low consumption design 6. IP40 protection, high strength metal shell, DIN rail mounted 7. -40~75â?? working temperature 8. Support MAC address self-learning
Qmin-SIL Series Fused Silica is made of high purity Chinese crystal Silica by electrically fusing (fusing temperature 1800-2000â??) to amorphous Silicon dioxide, then by alumina ball mill grinding, unique air classifying, screening, magnetic and other impurity seperating techonology, designed for EMC and other electrical application. Special Features: Very low coefficient of thermal expansion Excellent conductivity and Electrical property High Chemical Resistance Pure(high SiO2 content, low Fe, Na, K & Ti) High Whiteness High Hardness, good wearable Main Applications: EMC (Epoxy Molding Compound) Filler, coating powder Electrical Insulators Others GRADE (1). QMin-F/S-E200 d50: 20Micron +/-1 (2). QMin-F/S-E325 d50: 15Micron +/-1 (3). QMin-F/S-E600 d50: 9Micron +/-1 (4). QMin-F/S-E800 d50: 6Micron +/-1 Remark: the particle size is from d50 2-50um, the PS distribution is controllable Chemical Composition: SiO2: 99.85%Min. (Typical: 99.91%) AL2O3: 800ppm Max. (Typical: 300-500ppm) Fe2O3: 80ppm Max. (Typical: 25ppm) Extracted Water: Na+ 3ppm Max. Cl- 2ppm Max. Electric Conductivity: 3um/cm Physical Properties: Appearance: White Powder Specific Gravity: 2.2 Hardness( Mohs): 6.0 PH: 6.5-8 Whiteness: 96 Min. Igniting Loss: 0.1%Max. We can offer further product information and our technical experience if you need, and also are in position to supply specially designed product as customer requirement.
This product is made up of anti-alkali primer, modeling aggregate, colored primer, top coat for main material and water-based finishing paint, anti-alkali primer of which intensifies adhesion between this kind of art coating and substrate, reduces water absorption to substrate and prevents salt and alkali from separating. Main material of liquid granite may form color, pattern, crystal section and stereoscopic texture, which can reach adequate hardness. The coating is endowed with physical and chemical property of high weather resistance. Water-based finishing paint is situated at outmost part of coating system possessing hydrophobic nature & ventilation, anti stain, ultraviolet-ray resistance, anti-mildew & anti-alga etc. Finishing coat adopts liquid granite which may be blended with different colors to satisfy various architecture demands from different customers. It has quite good elasticity, comparative smoothness on surface, non-containing gravel and perfect simulation effect. The coating is perfect water resistant, stable dyeing, non-blushing, non-color difference, high decorativeness, high weather resistance, excellent insulation and energy saving etc. It also complies with national insulation & fire protection standard. Finishing coat: inorganic fiber board (thickness: 8mm, 10mm and12mm to be selected and to manufacture according to requirement details) Insulation course: extruded board (mineral wool board/polystyrene board/polyurethane and core material to be made as per design requirement) Selective thickness of insulation: designed thickness Substrate: inorganic resin board Specification: 600 x1200 (to manufacture according to requirement details) Fire protection: a class/ b1 class Installation method: bonding + anchoring -
TBK-202 Universal LCD Screen Removing and Installing Opening Repair Fixture Tool For Android Screen Saver Cable Side Open. TBK-202 LCD Screen Opener Mobile Phone Glass Separator with Powerful Suction Cups For LCD Display Disassembly. Description: 1. The new tbk-202 heat free liquid crystal screen separator is designed with strong suction and screw tension, Turn the screw to make the tension upward and the suction cup slow. Pull it up slowly to prevent the screen from exploding. 2. Adjustable mobile phone position and fixed distance are suitable for all models, and the camera groove is designed to avoid injury/damage to the camera. 3. The product can be removed from the screen left/right without damaging the cable. It is easy to operate and can be removed as soon as it is placed Features: 1.No heating, strong adsorption, no damage to the cable, and it can be disassembled immediately. 2.Strong adsorption / no heating / anti-corrosion / high temperature resistance. 3.No heating, novices can easily change the screen without hurting the cable. 4.Screw tension design, turn the screw to make the tension upward, and the suction cup slowly pulls up to prevent the screen from popping. 5.The fixed distance can be adjusted by turning the screw, the positioning is firm, easy to separate, and does not damage the fuselage 6.Camera groove design to prevent damage to the camera when disassembling the screen. 7.Disassemble the product left/right without hurting the cable. 8.The strong suction cup, the suction cup is evenly stressed, safe, reliable and stable, easier to absorb, and not easy to fall off. Operation: 1. Lift the 202 upper cover. 2. Place the mobile phone and turn the fixing screw to fix the mobile phone. 3. Put down the upper cover, pull down the suction cup and lock the switch. 4. Slowly turn the separation screw to separate the LCD screen (alcohol can be added during this period to make the separation easier.) Specification: Name: Screen Splitter Model: 202 Workbench size: 14~15.5CM Net weight: 0.6KG Product size: 20.5 8 5CM Gross weight: 0.8KG Packing size: 25.5 13.5 13CM Package includes: 1 x Screen Splitter
Magnifying Glass with Light, LED Illuminated Magnifier with 3X 45X High Magnification, Lightweight Handheld Magnifying Glass for Reading, Inspection, Jewelry, Hobbies ,Crafts Premium Optical Grade Lens: optical grade 3X & 45X magnification lens ensures a clear distortion-free image and life-time usage. And the scratch-resistant, crystal-clear lens are more clear and color-correct than common acrylic lenses. Comes with a lens cleaning cloth & storage bag, so feel free to use it whenever you want. Lightweight Handheld Magnifying Glass: magnifiers are made from high quality ABS plastic, smooth surface, ergonomic & lightweight design (only 5.8oz) makes it comfortable for handheld use. 3 LED LIGHTS Design - 3 Built-in energy-efficient LED lights are designed to help you to read at night or dark places; Easy to operate with a simple ON / OFF button switch; Powered by AAA batteries. (Batteries not included) Product Application: 3X lens is well designed for people with low vision and macular degeneration to do crafts, hobbies or read books, maps, magazines. 45X lens is perfect for miniatures, jewellery or professional inspection. Satisfaction Guaranteed: All products have a 30 days unconditional return & full refund service and 6 month quality warranty. Try this magnifying glass without risk (Exquisite packaging can be a perfect gift) Protect and relax your eyes, no headaches No more headaches when reading small prints on books, newspaper, leaflets, recipes, as well as sewing, crocheting and knitting instructions. This is a portable magnifying glass You can take it on your pocket or purse to vacation, airplane, train tour, or when shopping or in the restaurant. Ideal gift for the elderly and children Not only a good assistant for people with low vision and macular degeneration, but also a useful gift for stamp and coin collectors or or as a toy for children. Ideal gift for Christmas, Thanksgiving, Father's Day, Mother's Day, and Children's Day. Help you reading even in poor light conditions magnifying glass allows a professional, comfortable viewing for reading even in low light conditions. The LED is energy efficient and environmentally friendly with very low energy consumption and long lasting use. Package contains: 1 magnifying glass 1 Microfibre cleaning wipes 1 Good Quality Storage Bag 1 Instruction book Warm Tips: 1. No batteries included. In order to increase the service life, we high recommend that customers should use batteries with same brand and the same voltage. 2. Keep away from sharp objects to avoid scratching on Lens. 3. The focal length of the 3x magnifier is 4.92-5.9in, and the focal length of the 45x magnifier is 0.1in-0.2in. Once the object gets farther than 1 focal-length away from the lens, the image turns into an inverted image.
Magnifying Glass with Light, LED Illuminated Magnifier with 3X 45X High Magnification, Lightweight Handheld Magnifying Glass for Reading, Inspection, Jewelry, Hobbies ,Crafts Premium Optical Grade Lens: optical grade 3X & 45X magnification lens ensures a clear distortion-free image and life-time usage. And the scratch-resistant, crystal-clear lens are more clear and color-correct than common acrylic lenses. Comes with a lens cleaning cloth & storage bag, so feel free to use it whenever you want. Lightweight Handheld Magnifying Glass: magnifiers are made from high quality ABS plastic, smooth surface, ergonomic & lightweight design (only 5.8oz) makes it comfortable for handheld use. 3 LED LIGHTS Design - 3 Built-in energy-efficient LED lights are designed to help you to read at night or dark places; Easy to operate with a simple ON / OFF button switch; Powered by AAA batteries. (Batteries not included) Product Application: 3X lens is well designed for people with low vision and macular degeneration to do crafts, hobbies or read books, maps, magazines. 45X lens is perfect for miniatures, jewellery or professional inspection. Satisfaction Guaranteed: All products have a 30 days unconditional return & full refund service and 6 month quality warranty. Try this magnifying glass without risk (Exquisite packaging can be a perfect gift ) Protect and relax your eyes, no headaches No more headaches when reading small prints on books, newspaper, leaflets, recipes, as well as sewing, crocheting and knitting instructions. This is a portable magnifying glass You can take it on your pocket or purse to vacation, airplane, train tour, or when shopping or in the restaurant. Ideal gift for the elderly and children Not only a good assistant for people with low vision and macular degeneration, but also a useful gift for stamp and coin collectors or or as a toy for children. Ideal gift for Christmas, Thanksgiving, Father's Day, Mother's Day, and Children's Day. Help you reading even in poor light conditions magnifying glass allows a professional, comfortable viewing for reading even in low light conditions. The LED is energy efficient and environmentally friendly with very low energy consumption and long lasting use. Package contains: 1 magnifying glass 1 Microfibre cleaning wipes 1 Good Quality Storage Bag 1 Instruction book Warm Tips: 1. No batteries included. In order to increase the service life, we high recommend that customers should use batteries with same brand and the same voltage. 2. Keep away from sharp objects to avoid scratching on Lens. 3. The focal length of the 3x magnifier is 4.92-5.9in, and the focal length of the 45x magnifier is 0.1in-0.2in. Once the object gets farther than 1 focal-length away from the lens, the image turns into an inverted image.
I. Introduction The SS-700 process VOCs monitoring system is based on the standards of HJ/T80, HJ/T75, HJ/T76 and other related standards, sampling by extraction method, configuration based on advanced gas chromatography, mass spectrometry separation technologies and hydrogen flame Ionization Detectors (FID), photoionization detectors (PID) to measure the composition of volatile organic gases such as total hydrocarbons (THC), non-methane total hydrocarbons (NMHC), aromatic hydrocarbons, esters, etc. According to the composition and detection requirements in the analysis project, it can be configured to meet the requirements of the analysis project and the frequency of analysis. At the same time, the optimization of instrument configuration can be performed to maximize the use of the instrument and ensure the continuity of sample analysis. reliability. The analysis system fully considers sample gas conditions, dew point and other factors, and specifically designs the pretreatment system to prevent the crystallization of components in sample gas from condensing and changing the concentration of components. The instrument uses special column combination, center cutting and back blowing technology and hydrogen flame ionization detector (FID) technology for detection. The FID Hydrogen Flame Ionization Detector is a typical mass detector that measures the mass change rate of a component in a GC gas. The response value is proportional to the mass of a component entering the detector per unit of time. II. Features 1.The system piping is imported clean stainless steel pipe to reduce adsorption; 2.The system adopts full calibration to eliminate the influence of a small amount of adsorption on the measurement. 3.The analytical method is consistent with the calibration method, and it is detected by GC-FID method. 4.The whole process of high-temperature 180 °C with hot sample transmission, high temperature FID detection, to avoid high-boiling VOCs adsorption and condensation, more accurate measurement; 5.Continuously run maintenance-free design, start-up automatic cycle operation, real online analysis; 6.The whole flow path insulation design is 180°C, no water vapor condensation, to avoid corrosion degradation of parts, suitable for high temperature / high humidity / corrosive conditions; 7.Non-methane total hydrocarbons and simultaneous monitoring of benzene, toluene, xylene and other components III. Application fields It is used for on-line monitoring of organized organic waste gas emissions from chemical, printing, pharmaceutical, rubber, spray coating, electronic semiconductor, synthetic leather, organic waste gas recovery.
SV bulk solid heat exchanger is a kind of heat exchanger using pillow plate to heat or cool bulk solid particle or powder. Technical features: 1.Dense phase conveying design: The speed and temperature of powder discharging is even and controllable, with stable and reliable quality. 2.Wall type heat exchange: Heat exchange medium exchanges heat with powder by high efficient pillow plate, no direct contact with powder. Product Advantages: 1.World leading laser welding pillow plate heat exchange technology: Pillow plate is laser welded by two plates all around and in the middle area full of weld flowers. After the forming process, the inner part of the heat exchange plate forms a pillow type cavity. Pillow design creates excellent turbulence and provides self supporting structure. In practical applications, the additional welding path is often added in the pillow heat exchange plate, in order to adjust and control the flow of fluid into and out of the heat exchange plate nozzle position, the fluid velocity and flow rate inside plate, so as to optimize the heat exchange effect. 2.Full closed operation with zero emission: In the process of using wall type heat exchange technology of SV bulk solid heat exchanger, there will be no direct air contact with bulk solid. So it fundamentally eliminates dust, fine particles and odor emissions, as well as prevent dust explosion effectively. 3.Saves energy up to 90%: Compared with the traditional heat transfer technology, the energy consumption of SV powder flow heat exchanger is decreased by more than 90% 4.Ensure superior product quality: The controllable low velocity when the powder passes through the heat exchanger can effectively prevent the wear and tear and decomposition of product. Also ensures the particle properties and crystal shape, so as to achieve the best product quality. 5.Even heat exchange effect: Based on dense conveying principle, powder in the heat exchanger flows evenly and in low speed, which ensures the even temperature of product discharging. Also the temperature of final product has good consistency. 6.Modular structure, easy to expand: The vertical structure of SV bulk solid is compact and modular. The processing amount could be adjusted by increasing or decreasing pillow plate quantity. It saves lots of installation space. 7.Compact structure, easy to install The wall type heat exchange and dense conveying designs means there is no need of high power consumpting equipment, such as electric motor, fan, dust catcher and emission control systems.
Silicon Carbide Heating ElementDescription Silicon Carbide Heating Element can be installed and replaced while the tin bath is operation. The heaters can be installed through the side-seal, or through the side of the bath roof, and are commonly used to extend campaign lives, where conventional elements in the side zones have been broken, and insufficient power is available. Silicon Carbide Heating Element Advantages High purity raw materials; High structural density; Slow aging; Maximum temperature being up to 1500â?? (2732�°F); Easy to be installed and replaced. Types and Applications of Silicon Carbide Heating Element 1. SW (Standard) SW Silicon Carbides are used in applications ranging in temperature from 600�°C up to 1400�°C in both air and controlled atmospheres. Although the type of atmosphere used will determine the maximum recommended element temperature. This kind of silicon carbide elements can be mounted either vertically or horizontally. 2. U-TYPE U shape Silicon Carbide is consists of two silicon carbide rod with same diameter. Each rod has both hot zone and cold end with identical resistance. Two rods are connected by the low resistance SiC. Also the connector could be used as holder according to different requirements. 3. W-TYPE 3-phase elements are available in 2 different types: SGC (Dumbbell), SGD(Standard). These elements are self-bonded silicon carbide formed by re-crystallization of silicon carbide at high temperature. It consists of three high-purity silicon carbide rods connected at one end by a silicon carbide crossbar. SGC elements are designed for vertical installation in standard float glass bathes and SGD elements for horizontal installation. They can be connected directly on three-phase power supply and is a one-side terminal type which permits drawing out the terminals from the roof of the furnace. 4. Single Spiral Silicon Carbide and Double Spiral Silicon Carbide: They are made from silicon Carbide powder, and have two shapes: single and double sprial silicon carbide heating element. They are widely used in all kinds of kilns and furnaces.
VVDI BE Key Pro Improved Version and For Benz Smart Key Shell 3 4 Button XNBZ01EN for VVDI MB Tool. Features: More compatibility New design High Stability High reliability Xhorse BE smart key: Frequency changeable Reusable - you can reset it Workable with Autel IM608, CGDI and VVDI MB, Key Tool Plus Can use Xhorse Mercedes smart key 3 button on 2 button key and it worked lock/unlock/ trunk Just on non keyless go VVDI BE Key Update Features: 1. Fix the bug that W164/W639 EIS data doesn't synchronize the key. 2. Fix the bug that the BE key fails to turn on the ignition after repeat try. 3. Fix the bug of trunk remote open. 4. Fix the bug that the BE key only transmitted RF signal for one time, after update, the RF signal can be transmitted for two times when press and release the key. 5. Modify the rolling algorithm, fix some errors of BE key. 6. Add pre-roll algorithm: the HASH value can roll ahead. 7. Adopt car-grade quartz crystal, improve infrared communication stability. 8. Boost the infrared signal when you press the button. 9. Support resetting the key frequency between 315MHZ and 433.92 in the way of VVDI MB tool or the PCB SMD resistor. Tip: VVDI MB tool has priority over the SMD resistor, which means if you reset the key frequency with VVDI MB tool at first, the SMD resistor won't work, and you need to use the VVDI MB tool to erase the frequency then use the SMD resistor. The ways to reset the frequency: 1) with the PCB SMD resistor. Weld the 1K SMD resistor on the position the arrow points and the frequency is 315MHZ, after remove it will be 433.92MHZ. 2) Change frequency between 315MHz and 433MHz with VVDI MB Tool.
ANENG AN8205C Digital Multimeter AC/DC Voltage Meter DC Ammeter Resistance Temperature Tester,ANENG AN8205C Digital Multimeter AC/DC Voltage Meter DC Ammeter Resistance Temperature Tester -20~1300 Features: 3 1/2 digital LCD screen, maximum display value 1999. Multimeter features a clear, easy to read LCD display, with white back Light. Portable & Compact Design. Data retention. Low voltage symbol display. Background light function. Overload protectio n. Pass measurement. Diode: Yes Audion: Yes Pass-through measurement: Yes Data retention: Yes Background light: Yes Maximum display: 1999 Specification: DC voltage: 200mV - 2-20-2000-600v plus or minus 0.5% AC voltage: 200V - 600V plus or minus 1.0% DC current: 2m - 20m - 200m - 10A + 1.8% Resistance: 200-2-20 k to 200 k, 2 k m �© plus or minus 1.0% Temperature measurement: K type thermocouple, - 20 â?? ~ 1300 â?? (+ / - 3%) Triode measurement: (PNP/NPN triode hFE) Diode measurement: Yes Pass test: Yes Input resistance: 1 m �© Electric pool: 9V, 6F22 (Battery is not included) Maximum display: 1999 (3 semi-liquid crystal display) Display size: 45 x 18mm Package included: 1 x ANENG AN8205C Digital Multimeter (Battery is not included) 2 x Pair Electronic Probe 1 x User Manual Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! There might be 0-1cm errors due to manual measurement.Please allow slight error of measurement.
CJ6+ OCA glue remover tool for mobile phone pads tablets glass touch sceen glue cleaning. Electric hot glue clean machine CJ6+ handheld glue remover for Phone Screen LCD OCA Glue Cleaning. Specification: Purpose: Professional mobile phone LCD screen electric cleaning tool, used to remove glue. Size: 15.5x10.5x4.5cm / 6.1x4.1x1.7 inch Electro-motor Size: 11.5x4.5x2 cm / 4.5x1.7x0.7 inch Material: plastic/metal. Features: In addition to the use of brushless high precision imported motor, the OCA glue removal tool is also very safe and efficient. It is designed with automatic protection function (more than the maximum torque will take automatic protection), more secure. It is used for rolling or removing the OCA glue on mobile phone LCD screen with very safe, convenient and efficient operation. Can remove OCA glue, apple whole series of original glue, OPPO, VIVO and many cell phone liquid crystal glue. The phone fix assistant is an ideal solution for , Samsung, Oppo and any other cell phone LCD repair. Precautions: The principle of OCA glue removal tool is to use the fine needle to roll up the OCA glue on the screen; Before use, the screen can be placed on the adhesive pad or vacuum separator, try not put the screen with backlight on the separator after heating; In the process of removing glue, hold one of the fine needles, and the other hand control the motor switch; When the fine needle film glue to a certain amount, pay attention to take off some glue, when the tool roll too much glue and cannot work smoothly, control the button both clockwise and counterclockwise on motor.
1. Chip Description MS8310 is a highly integrated chip designed for 2.4G wireless mouse. It innovatively realizes the radio frequency module of 2.4G wireless mouse. Three-in-one modules of main controller and optical sensor Radio Frequency Module of Wireless Mouse, The main controller module and the optical sensor module are integrated into one chip technology. With very few peripheral components, 2.4G wireless can be realized. Mouse has excellent anti-interference, high sensitivity, very low power consumption and other performance, and can maximize support for simplified production. 2. Main characteristics 2.4 GHz ISM band (2400-2483 MHz) Modulation: FSK/GFSK Vacuum Rate: 500Kps, 1Mbps, 2Mbps 8dBm transmission power Receiving Sensitivity of-88dBm Single-ended antenna feeding Single inductance network Single crystal oscillation Fast Frequency Hopping Algorithms 15 m transmission distance High-speed mobile detection reaches 28 inches per second The frame rate reaches 3000 frames per second. Supports three-file resolution 1200 (default)/1600/800 CPI Built-in low power sleep Sleep1/Sleep2/Power down mode Supporting remote wake-up function Good Compatibility of Computer Host and Operating System Wide power supply voltage range 2.0V-3.6V 3D 6K: LBUTTON, MBUTTON, RBUTTON, KEY4, KEY5, DPI Power Dynamic Control Technology and Power Management Support offline detection Compliance with safety regulations Support button wake-up mode Ultra-low power consumption is about 4.0mA (excluding typical value of LED current) Dormancy power consumption: about 20 uA SDIP14 package
These high definition stereo Earphones With Mic provide the excellent sound input& output quality that produce incredible natural high fidelity sound with deep bass and crystal clear treble . Deep base and clean treble for clear sound. The noise cancellation technology reduces several surround noise and ensures a clear voice to transfer to the one you call. The headphones with mic for mobile not only gives you attractive & stylish look, but also provide richer bass to meet your practical needs. Ultra-soft ErgoFit best in Ear Headphones with microphone conform instantly to your ears . Earphones with mic how to wear Step 1 Pay attention to the plug logo L is left R is right Step 2 Insert the earphone into the ear by the correct way , and rotate it slightly to the right place . Step 3 The wire is fixed to behind the ear Step 4 Hold the earphone , adjust the degree of seal Step 5 Adjust the earphone cord and secured to an appropriate shape Step 6 When worn correctly , the earphone should be fitted with the ear , comfortable and soundproof This headphones with mic for mobile Using multislice material to reduce the noise interference Stereo headphones , its Resonator cavity a more powerful sound shock Stereo headphones . This best in ear headphones with microphone adopt TPE anti-winding design enhances the durability, flexibility and longevity of the cable . the line more dirt-resistant , tough and durable . Looking for ideal Earphones with Mic Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Headphones with Mic for Mobile are quality guaranteed. We are China Origin Factory of Best in Ear Headphones with Microphone. If you have any question, please feel free to contact us.
High Temperature Li-Ion battery cells High-temperature lithium-ion battery refers to a charging temperature higher than 45 with a discharge temperature higher than 60 , and has a good storage performance and a long life cycle. Design Features: Adopting roasting technology mixing with metals for anode material improves the crystal texture stability of LiCoO under high temperature and decreases its oxidability which prevents chemical reaction between electrode and electrolyte. Heat-resistant electrolyte increases the burning point and slows down reaction under high temperature. Application fields: Instrumentation, robotic, Medical, business and Security equipment; Energy storage and emergency backup power systems, etc I/ Products specs Model 503450-2S Dimensions 10*34*52mm Capacity 1000mAh Voltage 3.7V Environment of usage -20~80 Certifications CE,ROHS,UL,FCC,KC,IEC62133,CQC,UN38.3,MSDS II/ Production process FAQ 1.Q/ Should a protective plate be added to a lithium-ion battery pack? A/ Yes. To prevent an over discharge of the battery 2.Q/ What is the advantage of the protective plate on the battery A/ To protect the battery through an overcharge and over current process. 3.Q/ Is it possible to have a larger capacity for a battery? A/The capacity and size of the battery is proportional to the size, the larger the size, the larger the capacity. 4.Q/ Whats a high rate battery? A/ If the current of the battery is too large or more than 3 C, it requires another battery. 5.-What's the storage capacity of a battery? The best capacity in storage is 30%-50% (voltage between 3.7-3.9V). 6.What's the temperature range of a battery in charge? The cell shall be charged within10~45 range in the Product Specification. Hot Tags: dash cam battery, batteries from China, battery suppliers, battery manufacturers, factory price batteries, customized batteries, batteries made in China
JHL85 8.5 Ton Wheel Excavator Introduction of JHL85 8.5 Ton Wheel Excavator JHL85 8.5 Ton Wheel Excavator Operating Environment · All-round expansion of the field of view, to increase the front and side windows and the rear window to ensure the vision, greatly reducing the dead zone, the operation more safe and efficient. · Increasing day window to improve upward visibility and increase ventilation. Doors and windows with tempered glass to prevent the visor to direct sunlight; ?¢ All operational control theory according to ergonomic design and layout. · Operating handle easily and easy to control. · Deluxe cab package, liquid crystal display panels, luxury seats. · Installation of air conditioning, indoor warm air to ensure rapid heating, cooling Intelligent operation and display · Large screen multi-function LCD monitor, digital display, full control of the engine operation (speed, water temperature, oil pressure, etc.), all kinds of machine operating information at any time. · Focus function switch on the control panel is arranged, through point-touch buttons and easy selection. * Using GPS satellite positioning system, remote diagnostics, fault warning, maintenance, automatic reminders. Convenient, fast repair and maintenance · Oil filter, pilot filter, fuel filter, oil-water separators can be disposed on the ground then check replace place. · Large-capacity fuel tank, to achieve a long job. * Large toolbox, storage is more conducive to spare items. · Repair and maintenance cycle longer: selection of high-quality parts, extended service life, reducing machine maintenance time.
Description of inventory storage mobile shelves: Compact shelving book shelves is frame structure,.The mobile shelving filing system door plate adopt new embossing technology making apperance more elegant. It consists of base,column,shelf,hanging panel,top panel,guard plate,door plate, transmission mechanism, track, shockprodd device, dustproof and rat device, and other parts. Details of shelf are available to be customized including the type, height, width, the number of layers and rows, etc. Track made of 20*20 square steel galvanizes surface to make sure that no rusting. Advantage of inventory storage mobile shelves: 1.ISO9001&ISO14001; Approval the ISO9001&ISO14001 quality inspection 2.High quality cold rolled steel plate; 3.Double bearings design,avoiding the problem of imbalance; 4.The shelf has been tested to prove that the ratio of the driving force and the loading weight is 1:1500, that is, the strength of 1kg is enough to drive the the load of 1500kg; 5.The surface is covered with environmental electrostatic powder coating to ensure pure color and smooth surface without crystallization; 6.Structure:detachable Item Office archives documents storage compactor bank mobile shelves Model No. YT-H-001 Size H2000*W900*D400mm H2000*W900*D780mm Thickness shelf is 0.8mm, column is 1.2mm. (can customized) Surface Electrostaic Powder coating Volume 0.72 CBM or 1.404CBM Usage Office, school,hotel, hospital,company, factory, law office and other commercial area. Warranty 5 years
