Description Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized. Recommended Use :- It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected Industrial shades FINISH : Matt SOLIDS BY VOLUME : 63 + 3% THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75 FLASH POINT : Base : Above 25C Hardener : Above 25C DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days SHELF LIFE : Base: 6 months Hardener: 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation ) POT LIFE : 2 hours at 30�°C APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 RECOMMENDED DFT : 75-100 �µ. OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing) OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
Whether you are supplying products for industrial piping, municipal water systems, or any number of different piping applications, Changhao offers expertise in fasteners for the piping industry. With so many rugged industrial and utility applications, we understand your need for the most durable, high-quality products. With our extensive inventory, we can easily find the right fastener for your specific application. If the product is not in stock, we can easily order it for you. To help your business improve the efficiency of your supply process, Changhao offers standard as well as customized kitting and packaging services. We are particularly well-equipped for large, complex jobs. Our fasteners are available in all standard and metric sizes, as well as a range of quality material grades and finishes, including steel, stainless steel, aluminum, brass, copper, nylon and specialty materials. What are pipe fasteners? A pipe fastener is a device that mechanically connects or secures two or more pipes together. Pipe fasteners include high strength and mild steel bolts, clamps, nuts, screws, washers, studs, pins and more. All types of fasteners are used in industrial and residential pipe fittings. Pipe fasteners are used in almost all types of industries. They are made from a variety of materials and come in all shapes, sizes and designs. Finishing of pipe fasteners: Metal pipe fasteners can be painted, lacquered or powder coated. There are various types of powder coating for metal pipe fasteners such as epoxy coating, polyester coating, nylon coating etc. Plastic pipe fasteners can be given different colors. The various finishes that can be applied after powder coating of metal pipe fasteners are as follows: Black Coating White Coating Chrome plated Brass plated Nickel Plated Pewter finish Gold color finish, etc. Usage of pipe fasteners: Pipe fasteners are widely used for fastening and securing a variety of construction pipes. Pipe fasteners are ideal for optimizing the functionality of the product. Many manufacturers are developing ingenious pipe fasteners. Some of these pipe fasteners are easily removable for quick disassembly so that the pipes can be easily upgraded or repaired, or recycled at the end of their useful life. In the long run, pipe fasteners can make a product an asset and a resource, rather than an expensive waste product at the end of its life. These are just a few examples of new efforts to begin improving the environmental attributes of pipe fittings through new and improved fastener designs and options.
(bataviadropship) Husqvarna Automower 430XH Robotic Lawn Mower uses smart technology from the world leader in robotic mowing(1) for a beautifully cut lawn 24/7 Use the Automower Connect app for convenient control of your robotic mower, including scheduling, tracking location, and checking mowing status Set up the Automower 430XH with the self-installation kit (included); place the charging station, lay the boundary wire, and install the guide wire The Husqvarna 430XH Robotic Lawn Mower features ultra-quiet, smart-mowing technology from the world leader in robotic mowing(1) to help you effortlessly achieve a beautifully cut lawn with easy control from your smart device. The advanced GPS-assisted technology automatically returns the electric mower to its charging station when the battery gets low. Seamless connectivity allows you to control the electric lawn mower from Amazon Alexa, Google Home or your smartphone with the Automower Connect app. The Husqvarna 430XH Robot Lawn Mower also features an adjustable cutting system and is designed for taller grasses, achieving up to a 3.6-inch cutting height. Each Husqvarna robotic mower works with a wide range of parts and accessories, from replacement wheels to Automower House Kits. (1)Based upon value sales (Dollars) Source Euromonitor International Limited; per Robotic Lawn Mowers category definition; Home and Garden 2022ed; retail value sales in RSP, 2021 data. Husqvarna Automower 430XH Robotic Lawn Mower uses smart technology from the world leader in robotic mowing(1) for a beautifully cut lawn 24/7 Use the Automower Connect app for convenient control of your robotic mower, including scheduling, tracking location, and checking mowing status Set up the Automower 430XH with the self-installation kit (included); place the charging station, lay the boundary wire, and install the guide wire Smart lawn mower is equipped with GPS theft tracking, a built-in alarm system, and PIN code lock so you can secure and track its location at all times For medium to large yards (0.8 acre), this robot mower mows up to 145 minutes on a single charge with an area capacity of 1,430 square feet per hour Robot lawn mower is weatherproof and can navigate narrow passages, objects and 45%/ 22-degree slopes, making it perfect for complex yards Battery powered lawn mower with a 9.45-inch cut width and a 2- to 3.6-inch cut height designed for taller grass types Features three blades that cut less grass more frequently for a beautifully maintained lawn Husqvarna robotic mower uses collision and lift sensors that stop the blades instantly when the mower is lifted
Swift MFL portable instrument with a large, premium-quality multi-touch display. Incl.2 batt., power supp., manual, rugged case. Highlights : Fast, reliable corrosion screening even in service Portable, battery-operated, sealed, large bright display Simple to learn and operate, offers a high PoD SPECS : Acquisition modes Internal Clk, Encoder Array connectors 1x IPEX Batteries - typical life 6-8 hours Cooling Sealed with internal fan Data storage SSD, 100 GB Display resolution 1024 768 Display size 26.4 cm (10.4) Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement Full recordable data for mapping Yes High temperature inspections Yes Highly portable easy to use system Yes Multitouch control Yes Nb. of input channels 8 Nb. of receiving elements Up to 128 Paperless Reporting Yes Precision active steering No Probability of detection 2mm diameter 20% loss Probe type MFL Rapid Coverage Yes Rope access applications Yes Setup creation/management Yes Umbilical length 5m, 10m and 15m Acquisition rate Up to 50 kHz Automatic screenshot with defect entry Yes Batteries - type 2x li-ion, rechargeable, DOT compliant Compliance EN 61010-1, CE, WEEE, FCC, Part 15B, ICES-003, RoHS Defect table (for reporting) Yes Digitizing 16-bit resolution Encoders and I/O connectors 1x 12-pin Fischer Inspection workflows Optimized, with hard buttons MFL receiver gain 23 - 64 dB Programmable alarms Yes Recordable UT data sets Yes RFT/NFT/MFL connector Yes Harness available Yes Full screen mode Yes Connectivity Gigabit Ethernet, Wi-Fi, HDMI, USB 2.0 (x3) Dimensions (W x D x H) 355 288 127 mm (14.0 11.3 5.0 in) Encoder inputs 3-axis Quadrature / Step /Dir, TTL 5V IP rating IP65 Operating humidity 95%, non-condensing Operating temperature 0 C to 40 C (32 F to 104 F) Power supply/requirements Battery Operated Programmable outputs Yes Supported Technologies/Techniques MFL Storage temperature 0 C to 40 C (32 F to 104 F) Volume 13L (793.31 in3) Weight (without batteries) 5.7 kg (12.5 lb) Video output HDMI Weight (with batteries) 6.6 kg (14.5 lb)
The six-party drill pipe is made from AISI4145HMOD alloy steel According to API Spec.7 -1. IT is formed by hot forged and fully heat-treated by intermediate frequency induction heat treatment or 20m horizontal optical resistance furnace to threads are phosphated, copperrized or cold worked. Â Standard size of hexagonal kelly;Each can reach a total length of 27 meters. Kelly size Length drive section Length overall Length drive section LD Standard LD Optional L standard L optional DFL Across flate DC Across cornere DCC Across cornere Rc Radlue Rcc Radlue Wall thickness eccentric bore 76.2 3 11280 12190 76.2 85.7 85.73 6.4 42.9 12.1 88.9 3 1/2 11280 Â 12190 88.9 100.8 100.0 6.4 50.0 13.3 108.0 4 1/4 11280 15540 12190 16460 108.0 122.2 121.4 9.9 60.7 15.9 Â 133.4 5 1/4 11280 15540 12190 16460 133.4 151.6 149.86 9.9 75.0 15.9 Â 133.4 5 1/4 11280 15540 12190 16460 133.4 175.4 171.45 15.9 85.7 15.88 152.4 6 11280 15540 12190 16460 152.4 173.0 173.02 9.5 86.5 15.9 Â 152.4 6 11280 15540 12190 16460 152.4 173.0 173.02 9.5 86.5 15.9 Â Upper box connection Thread size and style LF O.D. Bevel diameter Standard optional DU standard DU optional LU DF Standard DF optional 6 5/8 REG 4 1/2 REG 196.9 146.1 406.4 186.1 134.5 6 5/8 REG 4 1/2 REG 196.9 146.1 406.4 186.1 134.5 6 5/8 REG 4 1/2 REG 196.9 146.1 406.4 186.1 134.5 6 5/8 REG 196.9 Â 406.4 186.1 Â Lower pin connection I.D. Label O.D. LL DF Bevel diameter NC26 85.7 508 82.9 31.8 Â NC31 104.8 508 100.4 44.5 NC38 120.7 508 116.3 57.2 NC46 158.8 508 145.3 71.4 NC50 161.9 508 154.0 71.4 5 1/2 FH 177.8 508 170.7 82.6 NC56 177.8 508 171.7 82.6
The 77 series of high-performance PTO drive shafts provide the most popular drive shaft solutions for the lawn and turf industries. These PTO drive shafts come as complete assembly from tractor to the implement. They are made for long-term heavy-duty use and are able to meet the demands of large-scale farms and contractors. PTO shafts for tractor and Wide-angle CV PTO shafts can be adaptable to standard PTO driveshafts that are available on the market. Specifications of the 77 Series PTO Shaft The Easy Lock Guard Set Length 60.00 inches 1524 mm Outside Diameter 7.72 inches 196 millimeters Shipping Dimensions 60" L 60" L 7.72" H 60" L x 7.72" H 7.72" W 150.2cm L x 20cm H 20cm W Shipping Volume 3575.90 in3 58599 cm3 Shipping Weight 4.30 pounds 2 kilograms Weight 4.30 pounds 2 kilograms Yoke And Shaft HP@1000RPM 264 HP The power of 197 kilowatts HP@540RPM 172 HP 128 Kilowatts Length 32.75 inches 832 mm Dimensions of Shipping 34.25" L 3.6" H 5.75" W 95cm L x 87cm H 15cm W Shipping Volume 677.92 in3 11109 cm3 Kit of Bearings And Cross Diameter of Bearing 1.77 inches 45 millimeters Bearing Spannel 4.95 inches 126 millimeters Diameter of Bearing 1.77 inches 45 millimeters Bearing Spang 4.95 inches 126 millimeters Height 1.77 inches 45 millimeters HP@1000RPM 264 HP 197 Kilowatts HP@540RPM 172 HP 128 Kilowatts Kit Type E Length 4.95 inches 126 millimeters Interval of Lubrication 50.00 Dimensions of Shipping 4.957" L 1.772" H 4.957" W 13cm L x 5cm H 13cm W Shipping Volume 43.54 in3 713 cm3 Snap Ring Location External Width 4.95 inches 126 millimeters 7 Series replacement Parts Weasler PTO Shafts Parts Are you searching for an reliable source of PTO drive shaft components? At HZPT we offer everything you require to boost the performance of your tractors and implements. We have a variety of PTO shaft assemblies and components from top-quality manufacturers in the field. Our vast inventory lets us offer the products at competitive prices. In our assortment of tractor PTO shafts there's everything from shafts and yokes to rolling pins and drivetrains. We'd love to hear from you when you're struggling to decide the best products for your machine. Our team of experts can guide you to the proper direction.
PTO Shaft Replacement Of Weasler 44 SeriesOur ever-growing line of power supplies many parts that fall into the following categories: Power take-off shaft and other components: required to maximize the output power that the device can provide. Connecting rod for tractor: We offer a variety of 5-stage eight-stage, locking and T-handle hitchpins, and round snap, square, and round lock pins. Camera systems: use our camera observation system to increase the productivity, visibility, and safety in the workplace. Spray and other parts Choose from the essential spray parts from numerous drum pumps as well as top brands like Jet, Delavan and crop maintenance and many more. Transmission of power: you can find numerous Carlyle V-belt options for transmitting the power generated by the engine of the device to other crucial components. Specifications Of 44 Series PTO shaft Bore 1 1.37 inches 35 millimeters Bore 1 1 3/8-6 SPLINE Bore 2 Minus End Yoke Compressed (Closed) Length 38.00 inches 965 millimeters Compressed Overall Length 47.94 inches 1218 mm Connection 1 Quickly DISCONNECT Connection 2 YOKE Arms Extended Length 61.75 inches 1568 millimeters Extended Overall Length 71.69 inches 1821 mm HP@1000RPM 119 HP 89 Kilowatts HP@540RPM 77 HP 57 Kilowatts Length 47.94 inches 1218 mm Outside Diameter 7.28 inches 185 millimeters Dimensions of Shipping 45" L 45" L 7.28" H 45" L x 7.28" H 7.28" W 114cm L x 18cm H 18cm W Shipping Volume 2384.93 in3 39082 cm3 Shipping Weight 50.00 pounds 23 kilograms Weight 50.00 pounds 23 kilograms Weasler 44 Series PTO Shaft Parts Tractor Yoke Cross and Bearing Kit Shaft Shaft Weld Yoke Slip Sleeve Tube Tube Weld Yoke Implement Yoke Yoke & Shaft Assembly Yoke & Tube Assembly Drivelines Guard & Guard Bearing PTO Shaft Application Sizing a PTO Shaft When buying a new tractor that comes with an PTO shaft, or replacing one that is old or replacing an old one, the majority of PTO shafts require to be cut in order to fit the length of your tractor and equipment that is using it. This is the easy procedure we've outlined in the next steps. Connect the tractor and the implement three-point linkage, but not connect to the PTO. In order to determine how long the needed PTO shaft it is important to determine what distance is between the groove of the tractor's PTO shaft of output and that on the actual PTO output shaft.
VEHICLE SPECIFICATION DESCRIPTION Truck Model ZZ3257S3647W Truck Brand SINOTRUK HOWO Driving Position Rght /Left hand Driving Fuel tanker capacity 300 The Total Mass 35,000kg Cargo box 5600x2300x1500 mm Box thickness Boot 8mm side 6mm Dead Weight 12300kg Hydraulic Jack Front / Mid Lift Max speed 102 Color Optional Chassis & Add Components Frame Details High-Strength U-profile ladder frame with section of 300 90 8mm and reinforced sudfram, all cold riveted cross members. Dimension(Lx W xH) mm 8685x2496x3850 Overhang(front/rear) (mm) 1500/725 Wheel base (mm) 3625+1350 Engine Model WD615.47 Power 371hp/273kw.2000r/min Emission EURO II Displacement(L) 9.896 Type water-cooled four strokes 6 cylinders in line turbocharged, directly injection Kind of Fuel Diesel Fuel Consumption(L/100km) 25L/100km Clutch & Gear Box System Clutch SINOTRUK 430mm diaphragm spring clutch Gear Box HW19710 Axles Front Axle Model HF9 axle. Capacity: 9000kg Rear Axle HC16 axle. Capacity:2X 16000kg Ratio of rear axle 4.8 Electrical System Battery 2X12V/165Ah Alternator 28V-1500kw Starter 7.5Kw/24V Brake System Service brake Dual circuit compressed air brake Parking brake spring energy, compressed air operating on rear wheels Auxiliary brake Engine exhaust brake Steering system Model ZF8118 Type hydraulic steering with power assistance Wheels & Tyres Type 1200R20 Material Steel tires Quantity 10+1 spare Kin pin 50mm or 90mm Cabin Type HW76 Standard cabin single sleeper with air conditioner, all-steel forward control,55 hydraulically tiltable to the front,2- arm windscreen wiper system with three speeds, laminated windscreen with casted-in radio aerial, hydraulically damped adjustable driver s seat and rigid adjustable co-driver s seat, with heating and ventilating system, outer sun visor, adjustable roof flap, with stereo radio/cassette recorder, safety belts and adjustable steering wheel, air horn, with 4-point support fully floating suspension and shock absorbers
7 ton 360 degree mini/small full hydraulic 2 WD or 4WD digger 4 WD wheel excavators 7 ton hydraulic excavator with bucket 0.2m3 for sale cheap price Main Feature of JHL70 Wheel Excavator JHL70 Wheel Excavator Powerful configuration high performance domestic prices of imported configuration Domestic brand engine, strong power, high efficiency to meet the job requirements. Precise matching design with advanced energy-saving control of the machine and less fuel consumption. New cooling fan and a large muffler used to make the machine less noise; Adopting advanced turbocharging technology to enhance Plateau Adaptability machine; Unique mouth of the funnel-type fan housing, greatly enhance the ability of the engine intake air flow and cooling system to ensure continuous and efficient machine operation. Advanced hydraulic system High-end configuration: main pump, main valve, swing motor, travel motor, fuel tanks, pilot control valves and other components are used internationally renowned brands, ensuring product quality. Integration of the latest research results, reduce energy consumption, improved design, faster response. Strong and precise swing control: Improved vibration absorption characteristics, to ensure that the rotation stopping operation more accurate and smooth; by increasing the reserves of torque, giving the machine the ability to provide a more powerful swing; Cylinder with buffer function: boom cylinder and the arm cylinder, a bucket cylinder design a buffer can reduce the vibration and shock of the machine, reduce noise and extend cylinder life Double pump confluence technology: the main valve to increase the supply of the boom, arm and bucket cylinders each flow, enhance operational speed. Rugged and high reliability Rugged chassis, hydraulic power steering, wheel reduction axle, to improve the mechanical flexibility and durability. Important parts used articulated arm forging structure, by changing the shape and thickness, ease stress and improve durability. Boom is holistic welded, and finally boring boring, throw alkyl handled, can well strengthen the robustness of the size of the arm, extend the life of the pin and the sleeve, thus avoiding welding on Fracture, durable . ? Bucket cutting boards are made of special wear-resistant steel, for heavy operational requirements, coupled with wear resistant bucket teeth, side teeth, and improve the performance of the machine. Use thicker steel reinforcing plate and increased side, improve the wear resistance;
5 Ton Capacity Electric Winch. Motor CROMPTON/ GEC/ KIRLOSKER" Make Slipring Crane Duty Motor 960 RPM, 440 Volt, 3 phase, 1 Hr. rated 40% ED as per IS: 325 having 'B' Class insulation. Drum Made from Rolled steel as per IS:226 of adequate thickness with side flange. Drum running on Bearing to take adequate rope length. Shaft Forged from EN-8 steel machine fitted with Drum. Chassis: Fabricated from joist of adequate size as per IS: 226 to take all shocks. All the stands on the chassis are Boxed type. Reduction 1st Reduction: through Elecon/Radicon make worm reduction Gear Box totally enclosed running on oil. 2nd Reduction: through open machine cut Gear from carbon steel & pinion made of Alloy Steel duly heat treated. Break Electro Magnetic Hydraulic Thruster Brake of reputed make. Mechanical Bend Brake with screw system with Ferrodo Brake lineing. Extra safety Ratchet pawl arrangement on the side of the drum for not moving the drum in opposite direction for extra safety. Coupling We will provide flex. Brake Drum coupling on the out put of motor & Input of Gear Box. Flex. coupling pin type on the output shaft of the Gear Box & In put shaft of the pinion. Controls Drum controller of TAC Make 5/7 steps. Forward & Reverse mtio. Control panel in sheet in sheet metal Box for dust, heat & water resistance containing of : Isolator Overload Relay Contector Single phase preventor FuseHrc. Amp. Meter Voilt Meter (h) Neon Lamp Push Button for start & Stop Resistance Box 10 Minute rating. Wiring & Pairrting We will provide all wiring from weather proof ar mured copper cable of adequate size & the Winch will be painted by two coats of primer & Two coats of Grey paint. Operator seat We will provided operator seat by the side of controls. Note Speed of 5 Ton & 10 Ton winch is 8/1OMTS per minutes. General Description SKID Frame Type- Frame made out of heavy steel sections M.S. Drums M. S. Gear & Pinion. Teeth Cut on Gear Hobbing Machine for Perfect Pitch. Reduction through Gear Box and Bull Gear & Pinion. Hydraulic Thrustor Brake ElectroMagneticBrake Electro Magnetic Brake. Manual Brake Carbon Steel Shaft A Safety Ratchet System All controls within reach of operator. Variable Speed Motor. Load & Speed as per Requirement of the Customer. Detail required for submission by Customer Rope pull in Tons ( Capacity) Speed required Mtr./per Min. Rope size & Length required on Drum. Available Elec. Current supply. Description of Application. Other accessories required with.
Basic Info Model: H7 PX26D base Certification: TS 16949 Working Temperature: ï¼? 300 Degree Centigrade Transport Package: Carton and pallet Specification: Height: Max 19.1mm Diameter: Φ33.9±0.1mm Distance of pin: 11.5mm Diameter of hole: 0.8+0.1/-0.05mm Origin: Zhejiang, China HS Code: 85399090 Our Services 1. Sample order is acceptable, but you need to pay the sample and freight cost. 2. We will give you nice price if you are our regular customers . 3. Let us know if your order is urgent, we will choose the quickest delivery for you. 4. We will be online all the time. If there's no one answering, just leave a message,and we will give you reply as soon as possible. Introduction of Factory Invitech is a professional manufacturer of precision metal and plastic components. Our core technology team specializes in precision progressive die stamping, compression molding for more than 30 years. With our chief-engineer's efforts, we successfully cut the cost a lot while keeping the quality at the same level, we have grown into one of the biggest suppliers of auto lighting products now. How big is Invitech? We have more than 20,000ã?¡plant area and hundreds of precision punching machines, automation equipment and processing machinery. FAQ 1.What is the advantage of Invitech products? 1). Quite bright 2). Mature system 3). High quality material and components 4). Strict Quality checking system 2.What is the Minimum order quantity? MOQ: 10K pcs. We accept sample order and trial order. If your quantity is large, you could get a competitive price. 3. How to place an order ? 1). Tell us the model and quantity, consignee information, shipping way and payment terms. 2). We made invoice and sent to you. 3). Complete Payment after confirmed the PI 4). Confirm Payment and arrange production. 5). Ship goods to you 6). Send the tracking number or B/L(by sea). 7). Goods delivered 4. What is the payment method? Bank transfer(T/T) for Option 5. What is the Delivery time? Based on the quantity, small order: 1-3days, bulk order: 15-30days. 6. Delivery Way By Express (DHL, FEDEX, UPS, TNT, EMS etc) By Air By Sea
Basic Info Model: H4 Lamp Socket Process: Deep drawing and Stamping Process Industry: Metal Stamping Parts Tolerances: according to drawings Trademark: Invitech Transport Package: cartons and pallets Specification: Socket length: 36.5±0.3 mm; Fitness dimension of body with adaptor: 24±0.1 mm; Space between two pins: 17.2-17.5 mm; Origin: Zhejiang China HS Code: 853990 Product Description Name: High Precision Automotive Metal Stamping Auto Parts 1. Working Process: * Sample: R&D department control sample process directly. Save time and directly adjust working process. Sample time: 7-10days. * Production: R&D department finish working process drawing. Production department proceeding and IPQC proceeded. QC/Package department check final quality and finish package together. * All shipped pats are almost 100% checked by QC/Package department. 2. Equipment: * Equipment: full automation 3.Quality Control Process * In-come material checking * Quality controal in processing(IPQC). 2 QC worker checking during production every day. * Final quality control during package(FQC). 4. You will get * Competitive Price of Precision Machinery part * Good Quality Assurance * In Time Sampling & In Time Shipment * Quality Guarantee * Free Sample Can Be Provided Some Time * Low MOQ * Reply in 24 hours and fast quotaion 1) Are you a factory or trade company? We are factory, so we can offer you very competitive price and very fast lead time. Our sample lead time is 3~7 days and mass production lead time is 15~30 days. 2) Whether some samples can be provided? Yes. Samples can provided. Just need some sample cost and we'll return it back when proceed into mass production. 3) Will my drawing be safe after you get it? Yes. We will not release your design to the third party unless with your permission. 4) How to deal with the parts received when they are found to be in poor quality? Please rest assured that all our products are QC inspected and accepted with inspection report before delivery and generally there will no non-conformance; in case of non-conformance, please contact us immediately, take some pictures, we will check on the problems and have them reworked or repaired at the first time. The resulting transportation costs are borne by our company. Contact us: ADDRESS: No.916 Fengqing Road, Deqing Economic Development Zone, Huzhou City, Zhejiang Province, China E-MAIL: info@invi-tech.com url:http://www.invi-tech.com
Basic Info Model: H7 bulb socket Process: Forming Process Industry: Metal Stamping Parts Tolerances: according to drawings Customized: Customized Stamping Tonnage: 5-350t Delivery Time: 15-30 Working Days Trademark: Invitech Specification: Height: Max 19.1mm Diameter: Φ33.9±0.1mm Distance of pin: 11.5mm Diameter of hole: 0.8+0.1/-0.05mm Origin: China Product Description Invitech is a company committed to the manufacture and development of Metal stamping parts. The products widely used in Auto, Electric appliance, Electronics ects...Through years of operation, we have established solid, long-term and cooperative relationships with clients from India, Korea also Europe by providing manufacturing services ranging from parts to complete appliances and have become a professional metal stamping parts supplier. Brief information: Brief introduction Accident prevention Safety operation management Quality control liability system and periodical QC on line every hour shipment sample TNT/Fedex/DHL/UPS by air and sea Company profile Structure of company Private-operate Product Stamping parts/deep drawing parts/Welding parts/kitchen equipment accessories and components/Auto parts/Household Electric Appliances Type of company Manufacture Years of foundation 2009 Generation information Material Stainless steel/Galvanzied steel/Aluminum/Copper/Brass etc. Surface treatment like zinc plating/nick plating/powder coating/spraying etc. application Kitchen equipment/Electronic/appliance/Auto/Industrial equipment/metal stamping etc. Package polybag inside protect from contamination export carton outside protect from damage Processing include mold design/tooling fabrication/stamping/deep drawing/punching/cutting/bending/injection FAQ Q: How long is your delivery time? A: Generally 15-30 days for production. Q: What is your terms of payment ? A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance, balance before shippment. If you have another question, pls feel free to contact us as below: Email: info@invi-tech.com url:http://www.invi-tech.com
Hammer mill crusher Application Hammer mill crusher is suitable for mid-hard and light erosive Materials, whose pressureresistance strength is no more than 100Mpa and humidity lower than 15%, suchas coal, salt, chalk, gypsum, blocks, lime Stone, etc. Hammer mill crusher Operating Principle The main working part of hammer crusher is rotors with hammer. The rotors consist of main shaft, disk, pin shaft and hammers. The motor drives the rotors to rotate quickly in the crushing cavity. Raw Materials enter the crusher through the feed opening and are stricken, impacted, cut and ground by the high-speed hammerto small size. There is a screening plate under the rotor, so that Materials with size smaller than the screen mesh will be screened out and others are left tobe further hammered and ground until reach the st and ard size. The size of the final product can be adjusted by changing the screening plate. The gap between therotors and the screening plate can also be adjusted according to different requirement. Hammer Mill Design The major components of hammer mill, shown in the picture, include: - a delivery device is used to introduce the material to be ground into the path of the hammers. A rotor comprised of a series of machined disks mounted on the horizontal shaft performs this task. - free-swinging hammer that is suspended from rods running parallel to the shaft and through the rotor disks. The hammer carries out the function of smashing the ingredients in order to reduce their particle size. - a perforated screen and either gravity- or air-assisted removal of ground product. Acts to screen the particle size of the hammer mill to ensure particles meet a specified maximum mesh size. Feeder Design Materials are introduced into the paths of the hammers by a variable speed vein feeder. This type of feeder can have its motor slaved by a programmable controller to the main drive motor of the hammer mill. The operational speed of the feeder is controlled to maintain optimum amperage loading of the main motor. Screen Design The amount of open area in hammer mills screen determines the particle size and grinding efficiency. The screen must be designed to maintain its integrity and provide the greatest amount of open area. Screen openings (holes) that are aligned in a 60-degree staggered pattern optimize open area while maintaining screen strength. This method will result in a 40 percent open area using 3.2 mm (1/8 inch) holes aligned on 4.8 mm (3/16 inch) centers. Read more: evelyn@cncharcoalmachine.com
XHP220C, XHP180C, XHP180D, XHP165C Moto Grader Types of Motor Grader, Komatsu Motor Grader, Motor Grader, Motor Grader Caterpillar, Motor Grader Uses, Motor Grader Controls For Sale. 1. Famous brand diesel engine with reliable and powerful performance. 2. Torque converter and power-shift gear box introduced from Germany ZF inc. are integrated together. Six forward gears and three backward gears meet various requirements during machineâ??s working and transporting. 3. Driving axle with integrated free-wheel anti-slip differential and strong roller chain drive balance case, boxed oscillated steering front axle with leaned wheels. 4. Popular working mechanism with pendulum-arm connection rod structure. Standard equipped free-maintenance rolling-plate circle device. Double cylinders of the blade tip control can adjust the cutting angle depending on soil quality. 5. Flexible hydraulic control system with two sets of HUSCO five way control valve, Imported hydraulic equializing valve for the blade lifting, patent hydraulically-operated pin drawing device is designed firstly in board. 6. Steering system with center articulated jount and tilting turning front wheels can get offset travel of entire machine. 7. Service braking system of caliper disc brakes on four rear wheels and mechanical internal expending parking brake. 8. Electro-hydraulically operated with entire instrumental monitoring system, free-maintenance OPTIMA batteries. 9. It is optional for front dozing blade and rear ripper. Types of Motor Grader, Komatsu Motor Grader, Motor Grader, Motor Grader Caterpillar, Motor Grader Uses, Motor Grader Controls For Sale. Model XHP220C XHP180C/180D XHP165C Operating weight 16900 16000 15000 Front axle load 5820 5150 4150 Rear axle load 11080 10850 10850 Max. Forward speed 36.8 38.2 40.4 Max. Backward speed 24.8 24.5 25.7 Speed gear number F6/R3 F6/R3 F6/R3 Turning radius 7800 7800 7500 Hydraulic system pressure 18 18 18 Blade length X height 3965*610 3965*610 3660*610 Front wheel track 2150 2150 2150 Rear wheel track 2340 2340 2340 Wheel base 6362 6362 6062 Engine model 6CTA8.3 6BTA5.9/D6114ZG 6BTA5.9 Engine power 158 132/132 125 Overall Dimensions 8585*2790*3340 8585*2790*3340 8285*2595*3340
Stage Cementing Collar Hydraulic Type (Two Stage) Stage Cementing Collar Hydraulic Type (two stage) Hydraulic Stage Cementing Collar is a field-proven stage tool that meets the challenges of cementing holes at any angle with a hydraulically opened port system. It is specifically designed for horizontal sections / formations, the multistage cementing tool can be placed anywhere in the casing string. It is PDC-drillable and field-adjustable shear pins system. When the first-stage shutoff plug lands on the shutoff baffle, increased internal casing pressure hydraulically opens the stage tool, enabling circulation and then second-stage cement to pass though the ports into the annulus above the tool. The closing plug when released, wipes the casing ID clean of cement before bumping on a closing seat. Increased pressure shifts the closing seat downward, releasing locking lugs and closing the tool. A snap ring locks the sleeve in position, ensuring the stage tool remains locked. With 12 years export experiences, our stage collar, stage cementing collar hydraulic type, cementing basket, linger hanger and cementing plug has been welcomed in international markets. Stage Cementing Collar Mechanical Type (two stage) Stage Cementing Collar is used to effectively cement upper sections of the casing string after displacing cement around the lower section. The Multiple Stage Cementing Collar provides a means of opening and closing port holes for cement displacement and positive containment of the cement after displacement. All internal parts are easily drilled, and are firmly held from rotating during drilling. The port closing sleeve is positively locked in position after cementing. After running the Collar to setting depth, the lower section is cemented in the conventional manner except the cement is displaced with the flexible cementing plug furnished with the collar. This is bumped against the shutoff Baffle. A slight pressure build-up of 300-400 P.S.I. will assure plug is seated in Baffle. The port holes in the Multiple Stage Cementing Collar are opened for doing the second stage by dropping the trip bomb and applying approximately 800-1000 P.S.I. pressure. The second stage is displaced with the closing plug which is also furnished with the Tool. When the closing plug bumps approximately 800-1000 P.S.I. pressure will close the port holes.
Name: electroplated diamond & CBN grinding wheel for non-ferrous industry application No dressing,Body can be re-plated several times Introduction:Electroplated diamond and Cubic Boron Nitride (CBN) tools are made up of a basic single layer or multi-layers (depending on application) of either diamond or CBN particles that are bonded to the tool surface using a nickel matrix. The product can be made with various shapes and they are suitable for special complicated profile, surface grinding ,Internal grinding, Slot grinding,Profile grinding and small and others form grinding. Electroplated diamond and CBN tools are used for surface grinding ,Internal grinding, Slot grinding,Profile grinding Ceramics, Glass, Tungsten Carbide, Ferrite ,Chilled Cast Iron, Founded Alloy Steel, Titanium Alloy And etc Applications of electroplated bond grinding wheels: diamond tools for non - ferrous industry application * carbide (grinding green and sintered tungsten carbide) * ceramic (grinding ceramics like SIC, AJO,ZrO, etc) * automotive (grinding brake liners and cutting re-enforced rubber mouldings) * pharmaceutical (grinding factitious knee joint) * dental (profiling rubber bonded grinding pins) * ferrite (grinding magnetic parts) * chemical (grinding laboratory glass) * graphite (grinding graphite parts) * glass (grinding tubes, automotive components) * Fiberglass ,Plastics and Electronic components, etc CBN tools for metallic materials industry application * High-speed tool steels * Die steel * Hardened carbon steels * Hardened stainless steels * Alloy steels,Titanium Alloy * Aerospace alloys * Abrasion resistant ferrous materials, etc Advantages of electroplated diamond & CBN wheels: 1.No dressing procedure necessary,Body can be re-plated several times 2.High geometric and proportion precision,Complicated forming 3.retain their original shape and dimensions throughout their working life 4.Simple electroplated process, less investment convenient manufacturing 5.Excellent surface roughness, high grinding efficiency , long tool life 6.free-faster cutting, no dressing, less heating due to the diamond particles protruding from the surface. Please provide us details when you order, For example, Product needed: Resin bond diamond grinding wheel 1) Diameter (25, 40,100,200,300,750mm) 2) Hole/state bore dimension 3) Thickness (4/5/6/8/10/,40/50/60mm) 4) Shape (1A1 /1A1R/1A8/1A1W/1L1/1F1/6A2/12A2/11V9/4A1/14A1,) 5) Grit size (16/18, 18/20,40/45,80/100,325/400. In GB or ISO standard) 6) Other request
Name: electroplated diamond & CBN grinding wheel for non-ferrous industry application No dressing,Body can be re-plated several times Introduction:Electroplated diamond and Cubic Boron Nitride (CBN) tools are made up of a basic single layer or multi-layers (depending on application) of either diamond or CBN particles that are bonded to the tool surface using a nickel matrix. The product can be made with various shapes and they are suitable for special complicated profile, surface grinding ,Internal grinding, Slot grinding,Profile grinding and small and others form grinding. Electroplated diamond and CBN tools are used for surface grinding ,Internal grinding, Slot grinding,Profile grinding Ceramics, Glass, Tungsten Carbide, Ferrite ,Chilled Cast Iron, Founded Alloy Steel, Titanium Alloy And etc Applications of electroplated bond grinding wheels: diamond tools for non - ferrous industry application * carbide (grinding green and sintered tungsten carbide) * ceramic (grinding ceramics like SIC, AJO,ZrO, etc) * automotive (grinding brake liners and cutting re-enforced rubber mouldings) * pharmaceutical (grinding factitious knee joint) * dental (profiling rubber bonded grinding pins) * ferrite (grinding magnetic parts) * chemical (grinding laboratory glass) * graphite (grinding graphite parts) * glass (grinding tubes, automotive components) * Fiberglass ,Plastics and Electronic components, etc CBN tools for metallic materials industry application * High-speed tool steels * Die steel * Hardened carbon steels * Hardened stainless steels * Alloy steels,Titanium Alloy * Aerospace alloys * Abrasion resistant ferrous materials, etc Advantages of electroplated diamond & CBN wheels: 1.No dressing procedure necessary,Body can be re-plated several times 2.High geometric and proportion precision,Complicated forming 3.retain their original shape and dimensions throughout their working life 4.Simple electroplated process, less investment convenient manufacturing 5.Excellent surface roughness, high grinding efficiency , long tool life 6.free-faster cutting, no dressing, less heating due to the diamond particles protruding from the surface. Please provide us details when you order, For example, Product needed: Resin bond diamond grinding wheel 1) Diameter (25, 40,100,200,300,750mm) 2) Hole/state bore dimension 3) Thickness (4/5/6/8/10/,40/50/60mm) 4) Shape (1A1 /1A1R/1A8/1A1W/1L1/1F1/6A2/12A2/11V9/4A1/14A1,) 5) Grit size (16/18, 18/20,40/45,80/100,325/400. In GB or ISO standard) 6) Other request
Name: electroplated diamond & CBN grinding wheel No dressing,Body can be re-plated several times Introduction:Electroplated diamond and Cubic Boron Nitride (CBN) tools are made up of a basic single layer or multi-layers (depending on application) of either diamond or CBN particles that are bonded to the tool surface using a nickel matrix. The product can be made with various shapes and they are suitable for special complicated profile, surface grinding ,Internal grinding, Slot grinding,Profile grinding and small and others form grinding.Electroplated diamond and CBN tools are used for surface grinding ,Internal grinding, Slot grinding,Profile grinding Ceramics, Glass, Tungsten Carbide, Ferrite ,Chilled Cast Iron, Founded Alloy Steel, Titanium Alloy And etc Applications of electroplated bond grinding wheels: diamond tools for non - ferrous industry application * carbide (grinding green and sintered tungsten carbide) * ceramic (grinding ceramics like SIC, AJO,ZrO, etc) * automotive (grinding brake liners and cutting re-enforced rubber mouldings) * pharmaceutical (grinding factitious knee joint) * dental (profiling rubber bonded grinding pins) * ferrite (grinding magnetic parts) * chemical (grinding laboratory glass) * graphite (grinding graphite parts) * glass (grinding tubes, automotive components) * Fiberglass ,Plastics and Electronic components, etc CBN tools for metallic materials industry application * High-speed tool steels * Die steel * Hardened carbon steels * Hardened stainless steels * Alloy steels,Titanium Alloy * Aerospace alloys * Abrasion resistant ferrous materials, etc Advantages of electroplated diamond & CBN wheels: No dressing procedure necessary,Body can be re-plated several times High geometric and proportion precision,Complicated forming retain their original shape and dimensions throughout their working life Simple electroplated process, less investment convenient manufacturing Excellent surface roughness, high grinding efficiency , long tool life free-faster cutting, no dressing, less heating due to the diamond particles protruding from the surface. Please provide us details when you order, For example, Product needed: Resin bond diamond grinding wheel 1) Diameter (25, 40,100,200,300 ,750mm) 2) Hole/state bore dimension 3) Thickness (4/5/6/8/10/ ,40/50/60mm) 4) Shape (1A1 /1A1R/1A8/1A1W/1L1/1F1/6A2/12A2/11V9/4A1/14A1 ,) 5) Grit size (16/18, 18/20 ,40/45,80/100 ,325/400. In GB or ISO standard) 6) Other request