SX7740 Technical Parameters Work table size (LxW): 400x680 mm; Travels of X/Y axis: 400x500 mm; Cutting height of Z axis: 200 (customized according to material) mm; Minimum cutting thickness: 0.3 mm; Speed of wire: less than 15 (variable frequency) m/s; Feed speed: Controlled and regulated by computer software ; Range of wire storage capacity: less than 200 m; Diameter of wire : 0.16-0.42 mm; Tension control: A. Pneumatic adjustment,B.Electrical adjustment ; Cutting material: Fragile and non-conductive non-metallic materials ; Working fluid : Tap water (customized according to material) ; Power supply: 380V, 50HZ v; Power consumption: 2 kw; Maximum loading capacity: 400 kg; Approx. Machine weight: 1500 kg; Machine overall size (LxWxH) 1350x1760x1600 mm.
Technical Parameters Work table size (LxW): 330x620 mm; Travels of X/Y axis: 320x400 mm; Cutting height of Z axis: 200 (customized according to material) mm; Minimum cutting thickness: 0.3 mm; Speed of wire: less than 15 (variable frequency) m/s; Feed speed: Controlled and regulated by computer software ; Range of wire storage capacity: less than 200 m; Diameter of wire : 0.16-0.42 mm; Tension control: A. Pneumatic adjustment,B.Electrical adjustment ; Cutting material: Fragile and non-conductive non-metallic materials ; Working fluid : Tap water (customized according to material) ; Power supply: 380V, 50HZ v; Power consumption: 2 kw; Maximum loading capacity: 250 kg; Approx. Machine weight: 1200 kg; Machine overall size (LxWxH) 1140x1580x1540 mm.
Specification of Consol AS1200 1.1. Raw material No. AISI 304 1.2. Yield Strength 1020N/mm² 1.3. Tensile strength 1150 N/mm² 1.4. Weld factor 0.70(Rm weld/Rm) 1.5. Hardness HV5 : 360-380 1.6. Modulus Elasticity E 196000MPA 1.7. Density 7.9g/cm³ 1.8. Thermal expansion(20-200°C) 18x10-6 m/m 1.9. Thermal conductivity(100°C) 16W/m 1.10.Belt Operation Temperature -80~300 1.11.Belt Size 1500mm x 1.0mm 1.12 Belt size tolerance Thickness +/- 8% Width 0-2mm ,Straightness 5mm 1.13 Surface Roughness Ra0.4 µm 1.14 Surface Flatness: h:l1:250, hmax3mm 1.15 Maximum allowed conveyor speed 60m/min 1.16 percentage elongation A % 22 weld joit 18% 1.17 Belt Joint open length with one end welding prepared
The GBM-7.6 rail wave abrasion grinding machine is a professional machine used for the wave abrasion and grinding of the rail top. This machine is suitable for various rails of 43~75kg/m Engine power Honda GXV390, 7.6kW, single cylinder, air-cooled 4-stroke petrol engine Grinding wheel speed 3600r/min Feed accuracy 0.11mm Grinding wheel stroke 45mm Grinding wheel size: 150 55 70mm Profile wheel span 1000mm Dimensions 1700 460 800mm Weight 85kg
Original Batik Shirt (Pekalongan, Indonesia) The best cotton material Color does not fade, print process The stitching is neat, smooth and layered with croton slimfit and regular models Available sizes M - 4L Original batik product from Pekalongan city, Indonesia If you have any questions, please contact us happy shopping :)
Origin from Hubei, China Old and New Type track maintenance Stainless Steel Device size 1900*1200 * 2500mm Linkage Product name Automatic hydraulic track tamper Material Stainless steel Origin: Hubei, China Engine Honda GX390 four-stroke gasoline engine RPM 3600r / m Vibration frequency: 66.7Hz Max. Insertion force: 16KN Production efficiency: â?¥ 260 sleeper/hour Hydraulic system pressure: 5 ~ 6MPa Power supply 9.5kw
Ceramic Filter 10.7MHz DIP&SMD Two Package Size Available for FM Filter: OUTLINE DIMENSIONS AND MARK Appearance: No visible damage and dirt. 3.2 Construction: SMD ceramic packaging. 3.3 The products conform to the RoHS directive and national environment protection law. Items Content Withstanding Voltage (V) max. 50 (DC 1min) Insulation Resistance Ri, M min. 100 10V 1min Operating Temperature Range ( ) -20 +80 Storage Temperature Range ( ) -40 +85
Since the breakdown of Convid-19 virus, wearing kid face masks becomes daily protection in public places. Adult face mask size does not fit well for childrens facial protection, JQ Care made mask with kids special measurement, maintain the same quality and design as the adults face mask. We offer kid size mask in 3 Ply Face Mask, FFP2/KN95 Mask, or reusable Mask. Our disposable kid face mask perfectly cover the mouth and nose of children, adjustable straps and ear loops to keep them comfy all day. They can be worn at school, outside with friends, or running out for an errand. All the face mask list at JQ Care can be tailor made for kids size, you can refer to adult maskâ??s information or contact us directly. Benefits Of kids face masks for sale Comfortable and breathable Gentle to the skin Designed especially for children For more information about hand protection gloves and ppe kit disposable price, please feel free to contact us!
Crystals such as sodium chloride (NaCl), potassium bromide (KBr) and potassium chloride (KCl) are uniform, bright and high transmittance within 0.250-20 �¼m when thickness less than 10mm, and no impurity absorption. These single crystals are ideal materials for making optical elements for prisms, lenses, filters, and various windows in infrared devices and optical instruments. OST Photonics offers high quality KBr substrates for researchers and industries. Crystal orientation, size and thickness can be customized according to your requirements. Application of KBr Substrates Infrared devices optical instruments Advantages of KBr Substrate Uniform, bright and high transmittance within 0.250-20 �¼m when thickness less than 10 mm No impurity absorption Ability of KBr Substrates Orientation:,,, etc. Dimension: 1, 2, 10x10mm, 20x20mm, etc. Thickness: 0.5mm, 1.0mm, 2mm, 5mm, etc. Available items: windows, substrates, blanks and customized optics
Quick-Flip Nylon Latchs *Silicon seal and feet *Removable carry handles *Stainess steel hings *Corner SS#304 bottle openers *With Leak-Proof Drain Plug *2 kinds lid designs for choice *EVA pad on top of lid for choice. External dimension:59.1*44*47CM (23.27*17.32*18.1 5") Internal dimension (cm):45.7*34.7*36.3C M (18*13.66*14.29" ) Carton size (cm):45.7*34.7*36.3C M (18*13.66*14.29" ) Gross/Net Weight:12.5/11KGS (27.56/24.25 LBS) Cold retention:â?¥5days at 77â??(25�°C) with ice fully filled Container Load Quantity:210PCS/20GP; 436PCS/40GP; 510PCS/40'HQ; Main Material:lldpe wall+pu formed insulation Volume:55Quart/52Liters Packing:1 opp bag +1 piece /carton
*Aluminium Handle bar with Nylon Grab *Quick-Flip Nylon Latchs *Silicon seal *Stainess steel hings *Corner SS#304 bottle openers *With Leak-Proof Drain Plug External dimension:44*39*46CM (17.32*15.35*18.1 1") Internal dimension (cm):31.2*30.7*36.6C M (12.28*12.09*14. 41") Carton size (cm):45.5*40.5*49C M(0.09CBM/CT N) Gross/Net Weight:9.5KGS/8KG S (20.95/17.64 LBS) Cold retention:â?¥5days at 77â??(25�°C) with ice fully filled Container Load Quantity:310PCS/20GP;64 5PCS/40GP;755P CS/40'HQ; Main Material:lldpe wall+pu formed insulation Volume:33Quart/31Liters Packing:1 opp bag +1 piece /carton
*Quick-Flip Nylon Latchs *Silicon seal and feet *Removable carry handles *Stainess steel hings *Corner SS#304 bottle openers *With Leak-Proof Drain Plug *2 kinds lid designs for choice *EVA pad on top of lid for choice. External dimension:55.1*41*47CM (21.7*16.14*18.5") Internal dimension (cm):42.1*28.9*36.5C M (16.57*11.38*14. 37") Carton size (cm):56.5*42.5*49C M(0.117CBM/C TN) Gross/Net Weight:11.5KGS/10 KGS (25.35/22.05 LBS) Cold retention:â?¥5days at 77â??(25�°C) with ice fully filled Container Load Quantity:240PCS/20GP;50 0PCS/40GP; 585PCS/40'HQ; Main Material:lldpe wall+pu formed insulation Volume:45Quart/42Liters Packing:1 opp bag +1 piece /carton
Best Granite Supplier and Manufacturer Granite is undoubtedly the premier choice of builders and designers across nations. It is used extensively because of its beauty and durability wherein India stands for more than 120 available granite colors. Paradise Exports is a leading granite supplier with a range of quality granite collections that stays alive over the years. We are one of the best suppliers of granite in India, and pride ourselves for providing outstanding Calibrated Granite Tiles, Granite XL Tiles, and other natural stones. Cutter Size available from Length- 7ft to 10ft and Height-2.5 to 3ft Jumbo Size available from Length- 7ft to 10ft and Height-6 to 9 ft Thickness 16 mm, 18 mm, 20 mm, 25 mm, 30 mm 40 mm Available Applications Leather, Flamed, Brushed, Polished, Honed, Lapatura Counter/Vanity Top, Flooring, Cladding, Marble Handicrafts, Swimming Pool Areas, Bathroom Walls & Floors, Fireplace Walls, External & Internal Aids In Construction
Double Side Rail Hole Chamfering Kit The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long. Specification Model LJ-DJQ-S Type Rail Chamfering Tool Material Stainless Steel Dimensions (L x W x H) 40*15 cm Chamfer Diameter �?31-�?32 Chamfering Size 1�?45�°, 2.5�?45�° Application 43kg/m,50kg/m,60kg/m rail Weight 2.8KG
Double Side Rail Hole Chamfering Kit The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long. Specification Model LJ-DJQ-S Type Rail Chamfering Tool Material Stainless Steel Dimensions (L x W x H) 40*15 cm Chamfer Diameter 31-?32 Chamfering Size 145°, 2.5 45° Application 43kg/m,50kg/m,60kg/m rail Weight 2.8KG
Product Info for Nikon 25x120 Telescopic Binoculars with Fork Mount From watching boats from a balcony to gazing at the lunar surface, the Nikon 25x120 Telescopic Binoculars combine the viewing comfort of the latter with the power of the former to give you an optic that represents the best of both worlds. With a size and weight that prevents practical use by hand, Nikon includes their fork mount that allows you to easily handle the optic and mount them on a railing, a custom rig, or their optional pillar stand for permanent installation on a patio, balcony, porch, or backyard observatory. Performance Magnification: 25x Objective Lens Diameter: 120 mm Angle of View: 3�° (Actual) Field of View: 150.6' @ 1000 yd / 50 m @ 1000 m Minimum Focus Distance: 436.4' / 133 m Exit Pupil Diameter: 4.8 mm Eye Relief: 18.9 mm Interpupillary Adjustment: 58 to 74 mm / 2.3 to 2.9" Diopter Adjustment: -5 to +3 Focus Type: Individual Features Fogproof: Yes, Nitrogen Filled Water Resistance: Waterproof, IPX8 General Dimensions: 26.38 x 17.87 x 6.3" / 67 x 45.4 x 16 cm (Binocular Only) Weight: 30.86 lb / 14 kg Packaging Info Package Weight: 63 lb Box Dimensions (LxWxH): 33.5 x 22.25 x 20.25"
Model 4L126TIL Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 545(401)/2,200 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 11.4 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 114 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Model 4L126TIM Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 495(364)/2,100 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.9 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 102 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Model 4L126TIH Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 450(331)/2,000 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.3 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 88 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Model L126TIM Engine type 4 cycle, In line, direct- injection, water cooled with wet turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 400(294)/2,100 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.85 Compression ratio 17 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 77 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 6.0 Alternator capacity ( V- A ) 24 - 50 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 24 / 19 Fresh water pump type Centrifugal type, driven by gear Sea water pump type Rubber impeller type driven by gear Marine gear Model DMT144H (Dong-I ) Gear ratio 1.83 2.09 2.51 3.08 3.43 Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) without M/G mm 1,414 x 933 x 1,077 with M. gear mm 1,683 x 933 x 1,159 Engine dry weight without M/G kg 1,060 with M. gear kg 1,345
