The mb-ecb is one passive ethernet transmission that can transmit 10 base-t ethernet signal over one coax cable up to 642ft(196m).It allows any cctv ip camera or other ethernet devices to be connected within extended distance without power .With super interference rejection and high-end tvs for surge protection, mb-ecb can protect device from damange.In any harsh electrical areas.The device is often used in legacy installations where existing cable is re-deployed as part of an upgrade to ip cameras or other ethernet devices.Mb-ecb work in pairs .The transmission is extremely simple to use , with no ip or mac addressing required.
Mb-hd60i is a hdmi and ir signal extender that allows to transmit hdmi1.4a signal and bi-directional ir signal up to 197ft(60m) via one cat5e/6 cable, 480i hdmi signal up to 328ft(100m).It use advanced technology , supporting edid, cec, vesa ddc and hpd .The superior interference rejection and low emissions .Mb-hd60 allow hdmi1.4a signal to be transmitted in any harsh environment . It has built-in surge suppressor to protect hdmi equipment against damaging voltage spikes. Its crosstalk and noise immunity ensure quality hdmi signal.So it is widely used in high definition advertising system, conference system, family entertainment and.
Description of low power high performance of low cost wifi module price Dl2103b is designed as a wifi module based on atheros 4004 it has ultra-small Size and supports smd the module works as an iot node and has been widely used In iot appliances Applications of low power high performance of low cost wifi module price Smart gateway Iot products Consumer electronics Smart home appliances Industry control Remote device monitoring Features of low power high performance of low cost wifi module price Support 2 4ghz 802 11b g n with sta ap mode Support wep wpa wpa2 psk encryption mode Support multiple network protocols Option on board antenna or external antenna Low power consumption Ultra small size support smd Support online firmware updating Srrc authentication Rohs compliant Datasheet of low power high performance of low cost wifi module price Wireless parameters Wireless standard 802 11 b g n Frequency range 2 412ghz 2 484ghz Transmit power 802 11b +15+ -2dbm 11mbps 802 11g +14+ -2dbm 54mbps 802 11n +13+ -2dbm ht20, mcs7 Receiver sensitivity 802 11b -93dbm 11mbps cck 802 11g -85dbm 54mbps ofdm 802 11n -82dbm ht20 mcs7) Antenna option Built in pcb pin External i-pex connector Hardware parameters Data interface Uart gpio Operating voltage 2 9v ~ 3 6v Operating current Consistently sending: peak ~200ma Normal mode average ~50ma, peak ~200ma Low power mode average ~10ma, peak ~200ma Operating temp -20 c 70 c Storage temp -45 c 125 c Dimensions and size 15mm x 30mm x 3.5mm Software parameters Network type Ap sta Security mechanisms Wep wpa-psk wpa2-psk Encryption Wep64 wep128 tkip aes Update firmware Local wireless, remote Customization Sdk supplied Network protocol Ipv4, tcp udp
Wifi module esp8266 Dl2106a is designed as a wifi module based on esp8266.It has ultra-small size and supports smd.The module works as an iot node and has been widely used in iot appliances. Applications: Smart plug Intelligent home Internet of things Wireless control in industry Wireless sensor & industrial control Smart wearables Light control Features •support 2.4ghz, 802.11b/g/n with sta/ap mode •support wep, wpa/wpa2-psk encryption mode •support multiple network protocols •option on board antenna or external antenna •low power consumption •ultra small size. Support smd •support online firmware updating •srrc authentication •rohs compliant
Dl2102a is designed as a wifi module based on atheros ar9331. It's a small size, highly integrated product with competitive price. This module can be easily integrated in iot products which need wifi features. It has been widely applied in iot appliances by large appliance enterprises, such as midea, changhong, hisense, etc. Applications Smart gateway Iot products Consumer electronics Smart home appliances Industry control Remote device monitoring Features Support 2.4ghz, 802.11b/g/n with sta/ap mode Support wep, wpa/wpa2-psk encryption mode Support cable network Support multiple network protocols Support at+ instruction set for configuration Option on board antenna or external antenna Provide 1 uart and 4 gpio ports Compact surface mount module 22mm x 44mm x 7.2mm, plug-in package Single supply 3.3v operation Support online firmware updating Rohs compliant
Wifi-102 controller appeared, with the installation of controlling software on mobile devices like android & ios phones, tablet Wifi-102 controller Power supply dc cv smps Input voltage dc12v-dc24v Max current load max 3a*3 Output control flexibly control single color, cold warm color, rgb led lighting fixture Control distance max 100m Rgb color change mode 32 fixed modes, 8 diy modes Scene mode 9 Working temperature -20~50 Dimension l127.6w73h44.5mm Package size l135w80h50mm Weight (g.W.) 290g T1, t2, t3 remote control Input voltage dc5v (built-in lithium battery) Working current 30ma Working frequency 2.4ghz Transmitting distance 30m Battery capacity 1000mah Standby time 6 months Normal using time 30 days Dimension l145w55h22mm Package size l168w102h28mm Weight (g.W) 200g Software technical parameters Platform android 2.1 or above, ios4.3 or above, with the wifi function Size android(2.2mb), ios(3.4mb) Language english Category tool Others free, plug-in-free. Wifi-102 controller Power supply dc cv smps Input voltage dc12v-dc24v Max current load max 3a*3 Output control flexibly control single color, cold warm color, rgb led lighting fixture Control distance max 100m Rgb color change mode 32 fixed modes, 8 diy modes Scene mode 9 Working temperature -20~50 Dimension l127.6w73h44.5mm Package size l135w80h50mm Weight (g.W.) 290g
High availability, converged network services for Enterprise Distribution/Core or Service Provider networks. We have large real stock of new and refurbished or used Cisco equipment and other network equipment. including Cisco routers, Cisco switches, Cisco firewalls, IP Phone, GBICs, GLCs, WIC NM network modules, memory & flash, cables, and network kits.
Model: S251 Name: GSM 3G Power Distribution Monitoring System The GSM 3G Power Distribution Monitoring System is not only a smart power meter for measuring the power distributor voltage, current, factor, watts, frequency, active power, reactive power, when over current or exceed the pre-set value, will alarm immediately. The GSM 3G Power Distribution Monitoring System can be used for monitoring the oil temperature, oil level of the transformers. GSM 3G Wireless Power Line monitoring. The GSM 3G Power Distribution Monitoring System also can be used as a wireless security alarm system for the transformers, e.g.: theft-proof, fall down, and so on. 1. ARM® Cortex™-M4 32 Bit RISC Core, 72MHz inside, RTOS system; 2. Quad-Band GSM Frequency,3G, supports SMS and Voice and GPRS/3G communication; 3. Programmable by SMS Commands or PC Configurator via USB; 4. A/B/C phase power up it directly, Inbuilt large capacity rechargeable backup battery; 5. Suitable for three-phase four-wire system, input voltage: 100~400V, input current:0~5A; 6. Monitoring A/B/C 3 Phase input over current, over voltage , factor, watts, active power, reactive power exceeds alarm; 7. Power input PT,CT rate are programmable; 8. Accuracy of current, voltage is 0.2 class, power and watts is 0.5 class, sampling is 0.1seond. 9. Large internal memory can save 1000 event historical data; 10. 6 analog inputs, 16bits, supports 0-5V, 0-20mA, 4-20mA; 11. 2 digital outputs, 5A/30VDC,5A/250VAC, can be program to events or turn on/off by SMS; 12. 8 digital inputs, NC/NO/EOL type, when digital input recover can alert by SMS; 13. I/O ports with opto-isolated and lightning protection; 14. Provide one 5VDC@1A power for additional device; 15. Equips LCD to display the real time data and for programming; 16. 2 IP data centers, supports GDW 376.1—2009 protocol over GPRS/3G network; 17. 1 RS485 can be used as data transparent transmission for additional intelligent meters or PLC, with 15KV ESD protection; 18. Automatically resend the data while communication failure, GPRS failure will alert by SMS text; 19. 8 SMS Alert and auto dial numbers, can program to receive specified alarm message. 20. Automatically report its status to users by the specified time.
Model: S260 S261 Name: GSM GPRS 3G Temperature Logger The GSM GPRS 3G Temperature Logger is special for remote monitoring temperature. it can setup ultra-high—high, low—ultra-low 4 alarm level. and 1 digital relay output can control via free charge call, SMS or GPRS. Also, the internal memory can save the historical for half a year for review. It provides daily report, schedule upload, event upload by the GPRS/3G to monitoring center or by SMS to the user mobile phone directly. 1. Quad-Band GSM Frequency,3G, supports SMS and Voice and GPRS/3G communication; 2. Programmable by SMS Commands or PC Configurator via USB; 3. 2 alternate Server via GPRS/3G wireless network, supports IP address and DNS; 4. Compatible with KingCenter CMS-02 via GPRS(Google map), and CMS-01 through SMS; 5. GPS module is optional, measure the Longitude,Latitude,Speed,Direction ; 6. Daily report, schedule upload, event upload; 7. 6 authorized phone numbers, each number can be used to receive SMS or both, also can be used for dial to switch ON/OFF the relay outputs, inquiry status; 8. One digital outputs (dry contact, NO/NC) with relay rating 10A/240VAC for connecting the switch of the air conditioner or machines, the outputs can setup as always ON, Pulse output, by SMS, authorized phone number dial in, and alarm events; 9. 4 inputs, 12bits, can setup interval time, interval value, ultra-high, high, low, ultra-low alarm can active the relay outputs and send programmable SMS to authorized phone numbers or via GPRS to monitoring center; 10. Internal memory, can save the historical data for review; 11. External AC Power monitoring, AC On/OFF will send SMS to authorized phone numbers; 12. Rechargeable Backup Battery inside can last 18hours; 13. Standard DIN Rail 35mm installation or outdoor enclosure.
Model: S262 S263 Name: GSM GPRS 3G Data Logger The GPRS 3G Logger is special for remote monitoring temperature, humidity, current, voltage, fuel level, pressure, air condition parameters and so on, it can setup ultra-high—high, low—ultra-low 4 alarm level. and 1 digital relay output can control via free charge call, SMS or GPRS. Also, the internal memory can save the historical for half a year for review. It provides daily report, schedule upload, event upload by the GPRS/3G to monitoring center or by SMS to the user mobile phone directly. 1. Quad-Band GSM Frequency,3G, supports SMS and Voice and GPRS/3G communication; 2. Programmable by SMS Commands or PC Configurator via USB; 3. 2 alternate Server via GPRS/3G wireless network, supports IP address and DNS; 4. Compatible with KingCenter CMS-02 via GPRS(Google map), and CMS-01 through SMS; 5. GPS module is optional, measure the Longitude,Latitude,Speed,Direction ; 6. Daily report, schedule upload, event upload; 7. 6 authorized phone numbers, each number can be used to receive SMS or both, also can be used for dial to switch ON/OFF the relay outputs, inquiry status; 8. One digital outputs (dry contact, NO/NC) with relay rating 10A/240VAC for connecting the switch of the air conditioner or machines, the outputs can setup as always ON, Pulse output, by SMS, authorized phone number dial in, and alarm events; 9. 4 inputs, 12bits, can setup interval time, interval value, ultra-high, high, low, ultra-low alarm can active the relay outputs and send programmable SMS to authorized phone numbers or via GPRS to monitoring center; 10. Internal memory, can save the historical data for review; 11. External AC Power monitoring, AC On/OFF will send SMS to authorized phone numbers; 12. Rechargeable Backup Battery inside can last 18hours; 13. Standard DIN Rail 35mm installation or outdoor enclosure.
Model:S270 Name:GSM GPRS Remote Controller The GSM M2M RTU S270 is a remote terminal unit, special for remote monitoring and remote control. The RTU integrated industrial GPRS Module inside, it supports voice, SMS, and GPRS communications. Moreover, it integrated USB port for programming by user friendly PC software and upgrade firmware. Mainly Features: 1. ARM® Cortex™-M4 32 Bit RISC Core, 168 MHz inside, RTOS system; 2. Widely Rated voltage range, 9~36VDC, Inbuilt large capacity rechargeable backup battery; 3. Large internal memory for save 1000 historical data, USB port for configuration and upgrade firmware; 4. 2 analog inputs, 12bits, supports 0-5V, 0-20mA, 4-20mA; 5. 2 Relay outputs, 5A/30VDC,5A/250VAC; 6. 2 digital inputs, dry contact or level input. One of the input can be used as counter; 7. 1 temperature probe input, 1 humidity transducer input; 8. 2 IP data centers, supports Modbus TCP,TCP/IP protocol over GPRS/3G network; 9. Automatically resend the data while communication failure, GPRS failure will alert by SMS text; 10. Supports remotely restart the RTU, and configure it by SMS commands remotely; 11. Supports over voltage protection and phase-reversal protection; 12. 10 SMS Alert and auto dial numbers, can program to receive specified alarm message. 13. 10 access control authorized numbers, can open the BTS door or turn on/off machine with a free charge call at the specified time.
Model:S273 Name:GSM 3G M2M RTU (8DI+6AI+4DO+1TH+1USB+1RS232/485+64Registers) The GSM 3G M2M RTU is a multi I/O port remote terminal unit, through the RS232/485 port can connect intelligent meters or PLC. It is special for BTS monitoring, remote data acquisition, telemetrically, BTS access control and other applications. It supports voice communication, SMS, GPRS, 3G communications. Mainly Features: 1. ARM® Cortex™-M4 32 Bit RISC Core, 168 MHz inside, RTOS system; 2. Widely Rated voltage range, 9~36VDC, Inbuilt large capacity rechargeable backup battery; 3. 4G SD card for save historical data, USB port for configuration and upgrade firmware; 4. 6 analog inputs, 12bits, supports 0-5V, 0-20mA, 4-20mA; 5. 4 Relay outputs, 5A/30VDC,5A/250VAC; 6. 8 digital inputs, dry contact or level input. One of the input can be used as counter; 7. 1 temperature probe input, 1 humidity transducer input; 8. I/O ports with opto-isolated, RS232/485 with 15KV ESD protection; 9. 2 IP data centers, supports Modbus TCP,TCP/IP protocol over GPRS/3G network; 10. RS232/RS485 can performs Modbus RTU Master, Modbus RTU Slave, supports 01,02,03,04,05 code, up to 64 registers, the register arise alarm also can send SMS to alert; 11. RS232/485 can be used as data transparent transmission for different intelligent meters or PLC; 12. Automatically resend the data while communication failure, GPRS failure will alert by SMS text; 13. Supports remotely restart the RTU, and configure it by SMS commands remotely; 14. Supports over voltage protection and phase-reversal protection; 15. 10 SMS Alert and auto dial numbers, can program to receive specified alarm message. 16. 10 access control authorized numbers, can open the BTS door or turn on/off machine with a free charge call at the specified time.
Features Support USB3.0 Support 20MHz/40MHz/80MHz frequency 5G compatible with IEEE 802.11ac and IEEE 802.11a standard 2.4G compatible with IEEE 802.11n, IEEE 802.11g, IEEE 802.11g standard Detect the network and change transmit speed automatically Support WPA/WPA2/WPA-WPA2/802.1x and 64/128 bit WEP encryption Support WPS 2.0 Internal Omni-directional Antenna Support 2.4G and 5G dual band Support Wi-Fi Direct Support Multiple BSSID Support QoS-WMM, WMM-PS Support WPS: PIN, PBC Support Infrastructure mode, Ad-Hoc mode and Soft AP three modes Support Cisco CCX Low consumption management Supported OS: Window XP/Vista/Win7/Win8/Win8.1/Mac OS 10.10/Linux v3.0.0.1
Features Support USB3.0 Support 20MHz/40MHz/80MHz frequency 5G compatible with IEEE 802.11ac and IEEE 802.11a standard 2.4G compatible with IEEE 802.11n, IEEE 802.11g, IEEE 802.11g standard Detect the network and change transmit speed automatically Support WPA/WPA2/WPA-WPA2/802.1x and 64/128 bit WEP encryption Support WPS 2.0 Internal Omni-directional Antenna Support 2.4G and 5G dual band Support Wi-Fi Direct Support Multiple BSSID Support QoS-WMM, WMM-PS Support WPS: PIN, PBC Support Infrastructure mode, Ad-Hoc mode and Soft AP three modes Support Cisco CCX Low consumption management Supported OS: Window XP/Vista/Win7/Win8/Win8.1/Mac OS 10.10/Linux v3.0.0.1
T-Bridge stands for "Telephone Line Communication", Which enables high speed data transmission through telephone cables. Besides Telephone cables, any types of copper cables such as coaxial cables, speaker cables, and UTP cables can be applied. T-bridge can save network construction cost dramatically as it can utilize existing copper cables already wired.
Network equipment
Jaton Technology Limited is a professional engaged in mobile broadband communications equipment research and manufacturing of high-tech companies.Currently such terminal products as TD-LTE data module, FDD data module,WiMAX data module,indoor CPE, outdoor CPE , LTE base station and MIFI have already come into market.We are now providing not only general but also customized products and solutions for our customers. 1kg/pcs
JN6610 LTE Indoor CPE(Band31) Support VOIP function to meet the needs of overseas operators Support TR-069 and OMA-DM network management protocols Support VPN protocols including PPTP, L2tp and Ipsec Can be adapted to LTE modules in different frequency bands support standard mini-PCIe modules from partners Support internal or external antenna Simple, elegant and suitable for multiple locations Support PoE power supply to ODU, ODU+IDU total solution has the cost advantage 1kg/pcs
JN6100 is a powerful indoor CPE, with built-in Mini-PCIe interface inside. Support LTE modules both TDD and FDD, or multi-mode wireless access with various of modules. Support VOIP function to meet the needs of overseas operators Support TR-069 and OMA-DM network management protocols Support VPN protocols including PPTP, L2tp and Ipsec Can be adapted to LTE modules in different frequency bands support standard mini-PCIe modules from partners Support internal or external antenna Simple, elegant and suitable for multiple locations Support PoE power supply to ODU, ODU+IDU total solution has the cost advantage 1kg/pcs
JW0100 Product Feature Single-chip solution with low cost advantage Total industrial level devices Support TR-069 and OMA-DM network management protocols Support VPN protocols including PPTP, L2tp and Ipsec Can be adapted to LTE modules in different frequency bands; support Wimax/LTE dual-mode; support standard mini-PCIe modules from partners Built-in high gain dual-polarized directional antenna with the gain up to 10dBi or more, Support long-distance transmission between the base station POE power supply and easy to install Adapt to harsh outdoor environments, extreme high and low temperature, high UV radiation, Lifetime is more than 10 years IP65 class protection 1KG/PCS
