Features : * Switching power supply High efficiency and stability of the new switching power supply so that the signal transmission speed faster and more stable voltage changes, sensitivity stronger, lighter weight. * Intelligent signal limiter Each channel has an independent output signal overload distortion, automatic pressure limited function, when the output signals are now clipping distortion can be quickly restored to the output signal compression is not the biggest distortion level and no reduction in the frequency response of audio signals, to avoid DC level because of the audio signal output and burned speakers. * Multiple detection, multiple protection A soft start, the second start, the (low) pressure protection, output overload and short circuit protection. * High efficiency, low fever Efficient Class H amplifier, significantly reduce heat loss. * Pristine audio Metal Packaging, high-power transistors, Yanyi a pure, passionate, authentic audio effects. * Removable face Network Removable the hole into the wind-net, easy cleaning. FP-series Switching Power Amplifier ITEM: FP-2200 / FP-2400 / FP-2600 / FP-2800 Output Power: 20-20kHz, 1W with 1 khz 8¬+Stereo Power(RMS): 350W f- 2 / 550W f- 2 / 750W f- 2 / 950W f- 2 4¬+Stereo Power(RMS): 500W f- 2 / 800W f- 2 / 1150W f- 2 / 1350W f- 2 8¬+Bridged Power(RMS): 1000W / 1600W / 2100W / 2300W Frequency Response(+o/-0.3dB,1W/8¬+): 20-20KHz+0.5dB THD+N: 10KHZ
8ohms Stereo Power(RMS): 2X1050W 4ohms Stereo Power(RMS): 2X1600W Frequency Response(+o/-0.3dB, 1W/8ohms): 20Hz-20kHz, -3dB@135kHz Power Bandwidth (rated power at 4ohms 1%THD+N): 20Hz-20kHz, -. 1.1dB/+0dB TourClass Protection: ACL, IGM, AutoRamp, short circuit, DC voltage, turn-on/off transient, current inrush, sub/ultrasonic input THD+N (1kHz 1W ): -60dB Voltage Gain (rated power @ 8ohms): X40dB Input Sensitivity (rated power at 8ohms): 0.8V Input Impedance (balanced/unbalanced): 20Kohms/10Kohms S/N Ratio ("A"weighted, full power at 4ohms): 96.5dB Crosstalk ("A"weighted, full power@4ohms): >-65dB Class: 3 Step H Input Connectors (per channel): Female XLR (pin 2+, configurable for pin 3+). TRS (tip+) Output Connectors (per channel): 5-way binding posts or Speakon connectors (market dependent) Supply Power: 4158W Power Supply (factory configured): AC220V/230V, 50-60Hz Cooling: Two side panel variable speed DC fans, better than conventional cooling Controls: Front panel: 2 attenuators, power switch; Rear panel: Signal ground lift & mode switches. LED Indicators (per channel): Signal, Protect, Active, Critical Construction: Steel chassis, 16 gauge. Casting Aluminum front panel. Dimensions (HXWXD): 132X483X480mm (3U) Net Weight: 33.5kg Gross Weight: 34.35kg.
F600 Power Amplifier Key Feature: * 2/3U high, heavy duty steel chassis * Modular construction for easy servicing * Symmetrical layout for even weight distribution * High efficiency toroidal power transformer * Oversized, high energy, linear power supply * 3 steps, Class H Audio topology * Stereo, parallel or bridged operation * Twin balanced inputs (Neutrik XLR connectors) * Dual Speakon and Binding posts outputs * High quality components used throughout * Dual, continuously variable speed fans * Efficient two sides cooling, the efficiency is better than back to front cooling * Active, signal, protect and critical indicators * Duraluminium, 8mm thick front-panel * Unobtrusive carrying handles * Voltage Gain: 35 or 40 dB . Specification: 8ohms Stereo Power(RMS): 2X300W 4ohms Stereo Power(RMS): 2X462W 8ohms Bridged Power(RMS): 968W Frequency Response(+o/-0.3dB, 1W/8ohms: 20Hz-20kHz, -3dB@135kHz Power Bandwidth(rated power at 4ohms 1%THD+N): 20Hz-20kHz, -. 1.1dB/+0dB TourClass Protection: ACL, IGM, AutoRamp, short circuit, DC voltage, turn-on/off transient, current inrush, sub/ultrasonic input THD+N (1kHz 1W ): -60dB Voltage Gain (rated power @ 8Ic): X35dB Input Sensitivity (rated power at 8Ic): 0.97V Input Impedance (balanced/unbalanced): 20KIc/10KIc S/N Ratio ("A"weighted, full power at 4ohms): 99dB Crosstalk ("A"weighted, full power@4ohms): >-63dB Class: 3 Step H Input Connectors (per channel): Female XLR (pin 2+, configurable for pin 3+). TRS (tip+) Output Connectors (per channel): 5-way binding posts or Speakon connectors (market dependent) Supply Power: 1320W Power Supply (factory configured): AC220V/230V, 50-60Hz Cooling: Two side panel variable speed DC fans, better than conventional cooling Controls: Front panel: 2 attenuators, power switch; Rear panel: Signal ground lift & mode switches. LED Indicators (per channel): Signal, Protect, Active, Critical Construction: Steel chassis, 16 gauge. Casting Aluminum front panel. Dimensions (HXWXD): 88X483X480mm (2U) Net Weight: 19.2kg Gross Weight: 23kg.
Key Feature 1>. Medium and long-throw applications 2>. Ergonmic, fast, secure rigging system 3>. Ultra compact curvilinear array 4>. Trapezoidal design for curved vertical arrays 5>. Excellent speech intellgibility 6>. Highly versatile for both installation and touring. Application 1>. Band PA Systems 2>. Corporate Events 3>. Ballroom Events 4>. Large Houses of Worship 5>. Convention Centers 6>. Live Music Clubs . Specification * Frequency Response (+3 dB): 60 Hz - 19 kHz * Sensitivity (1w/1m): 101 dB SPL * Long-term SPL: 128 dB * Maximum SPL: 134 dB * Nominal Impedance: 4 ohms * Power rated: 700 watts * Peak Power handling: 1400 watts * Nominal Dispersion: 90H x 60V * Crossover Frequency: 2.0 kHz * Dimensions (H x W x D): 805 mm x 476 mm x 500 mm * Enclosure Material: 18mm polywood * Surface Finished: black catalyzed polyurethane paint * Grille: 1.5mm black perforated steel framed * Net weight: 58 kg * Low Frequency Driver: 15", 3" voice coil, 190mm magnet * Mid Frequency Driver: 6.5", 2" voice coil, 140mm magnet * High Frequency Driver: 1.7"compression driver. polymer diaphragm * Input Connectors: Neutrik NL4MPX2
Shining Jins Enterprise Co., Ltd. specializing in manufacturing & designing cold forge Pole piece (T-Yoke) for Loud-Speakers and alarms raw driver in Taiwan.
Rated Power output:1W*2 Impedance:4 Frequency responsw:140HZ-18KHZ S/N Ratio:60dB Power Imput:USB DC 5V. Dimension:64*70*145mm.
Rated power output:15w+3w*2 Impedance:8 Frequency responsw:90hz-16khz S/n ratio:65db. Subwoofer dimension:175*222*183mm Satellite dimension:110*110*122mm.
Speaker Carton
Speaker Parts: Frame, cone, damper, dustcap, voice coil 1.Frame from 2" to 18" 2.Cone from 2' to 18"
Permanent Magnet: 1.Isotropic & anisotropic ferrite magnet 2.Neodymium magnet 3.AlNiCo magnet 4.Speaker magnet & motor magnet
Welding helmet : Auto-darkening filter welding helmet, transmittance:780-1300nm < 0.027% 1300-2000nm < 0.094auto switch time: < 0.02s ( at 21 centigrade)
Magnet(NdFeB, Ferrite, SmCo, AlNiCo), Magnetic assemblies(Pot magnet, Motor Parts, loudspeaker driver), Magnetizer, Magnet Lifter.
Acoustic components: loudspeakers, buzzers, transducers, piezo elements, sounders, receivers, speakers, microphones, earphones, headsets, other electronic components.
Mixer series, professional amplifiers, loudspeakers, microphones, dj mixer, cd player and other circumjacent equipment series.
Professional amplifier, power amplifier, loudspeaker, professional speaker, ktv system, line array, speaker, amplifier, audio processor, microphone.
Speaker driver, home audio, home cinema system (amplifier, bookshelf, floorstaning loudspeaker).
La-12 is a bi-amps, line array system which is made of one 12", one 3"titanium neodymium compression drivers and high-performance low-distortion compression driver with innovative horn design of waves phase philosophy. It is a zero interfere line array with multi- speaker combined to produce accurate directivity and maximum dynamic impact. Each enclosure is equipped with rigging system, allowing flown array to be constructed rapidly and safely. T-12 is a compact line array enclosure designed to bring superb line array performance to large stadiums, big outdoor concerts and commercial events. The switchable one or bi-amplified two way cabinet is very efficient, it meets the need for a high power, high bass impact system that is versatile and scalable for a very wide range of applications in the live sound, corporate and fixed installations. Model La-12 Type Array system Frequency response 55hz-20khz±3db Power handling 400w(rms)800w(peak) Sensitivity 100db(1w@1m) Max@s.P.L 126db(peak/1m) Lf section 12"(310mm) woofer 75mm(3in)coil Nominal impedance 8 ohm Hf section 1×3"compression driver 44mm titanium diaphragm Nominal impedance 8 ohm Output section 2-channel Dispersion pattern 110°h×5°v Finish Black paint Speaker cables Passive 1(+), 1(-). Built in Crossover Bi-amp lf 1(+), 1(-) Hf 2(+), 2(-) Input connectors 2×nl4mp speakon Dimensions 355×593×434mm(w×h×d) Package dimensions 425×660×505mm/0.14cbm Enclosure Brich plywood Net weight 28kg Gross weight 31kg
LA-28 is a two-way line array module with high efficiency which specially designed for medium and small-scale performance. Two 8" neodymium magnet LF loudspeakers with 3" voice coil. The modules are designed to be used in multiples with a minimal configuration of three. Up to 20 units can be arrayed to achieve extreme high levels needed for larger venues. - Medium scale venues (concert hall, auditorium, theatre, clubs), touring show, rental market - Drivers:2x8" LF;1x3" HF Frequency Response 70Hz-20kHz ± 3dB Power handling LF 500W (RMS) 1000W (PEAK) HF 100W (RMS) 200W (PEAK) Sensitivity LF 97dB(1W@1M) HF 108dB(1W@1M) Max@S.P.L. LF 124dB(PEAK/1M) HF 128dB(PEAK/1M) LF section 2×8"(210mm) woofer Nominal impedance 8ohm HF section 3"compression driver Nominal impedance 8ohm Dispersion 110°H×10°V Speaker cables LF 1(+)1(-) HF 2(+)2(-) Input connectors 2×NL4MP speakon Dimensions 580×260×430mm(W×H×D) Package dimensions 650×330×500mm/0.11cbm Enclosure Plywood Net weight 23kg Gross weight 26kg
XA6950(II) Hybrid Integrated Amplifier XA6950II is a hybrid integrated amplifier. It integrates the characteristics for both solid-state amplifier and vacuum tube amplifier. Features: 1. Hybrid amplifiers (vacuum tube 6922 for preamp stage) 2. Build-in USB interface audio DAC 3. Two toroidal transformers for power supply 4. Remote control Package: carton Gross Weight:30kg Net Weight:28kg Dimensions: 430mm*460mm*170mm
XA6800R(II) Integrated Amplifier The Xindak XA6800R (II) adopts a new look and internals. It is a pure class A integrated amplifier designed with high standards in mind for our customers to enjoy their preferred music. Derived from the XA6800R, internals are made of carefully selected components with both objectives to improve sound performance and reliability. Operating as a pure class A amplifier, good heat dissipation is ensured through the design of copper heat conduction bridges on both sides of the amplifier. Not only does this provide a stable and reasonable operating temperature, but it enhances the power output. A symmetric design completes the picture around an R type power supply of excellent properties. These are few examples of details attached to the building and circuit design of this new integrated amplifier. Two meters across the front panel not only inform about the operation of the amplifier, but with a blue backlight also improves the aesthetic. The black housing, derived from our acclaimed High-End PA Power Amplifier, adds to the striking look. To complete the picture, the versatility of the new XA6800R(II) reaches new territories with the addition of a USB entry (on top of 4 analog inputs) to connect your computer and enjoy your digital music library. Thus equipped, the new XA6800R(II) is ready to become the heart of a simple to implement solution with astonishing performances that only class A amplifiers can bring to music lovers. package: carton, Gross Weight: 21kg Net Weight: 19kg Dimensions(mm):430*410*140
