Rail Profile Gauge Rail Profile Gauge is is mainly used to measure the vertical wear and lateral wear of the railThe reasonable design makes it lightconvenient operation and intuitive reading Features 1 Digital type with direct readings LCD display screen clear and readable No calculations requiredgives direct reading When reading hold down the HOLD button to fix the measurement value and facilitate reading 2 High measuring accuracy The measurement accuracy is 001m 3 Easy to use measure the vertical and lateral rail wear at the same time Position the rail wear gauge on the outer side of the rail Push the vertical and lateral rail wear gauge so that the measuring probe is in contact with the upper surface and inner side of the rail respectivelyThen the vertical and lateral wear of the rail can be read 4 Metric imperial unit 5 Support customize We could customize all kinds wear gauge according to different rail profiles and different measure points 6Fast calibrate Onekey zero clearing function can be quickly calibrated before each use to reach the factory measurement accuracy 7 Magnetic fixed part Strong magnetic fixed part to attach to the rail 8 Rail fillet as measuring base to ensure measure data more accuracy Rail fillet is more clear than rail bottomno dust It could ensure the measure result reliability 9 Portable Handle This product is designed with a handle that is easy to hold which greatly improves the portability of the product It can avoid touching the ruler body directly cause the ruler body to be stained and corroded improve the product service life Model LJGMA Center vertical wear measure range 015mm Lateral wear measure range 025mm Score value 01mm Indication error 0 15mm Supply Customize UIC6060E1 UIC54 54E1 115RE 68TR ect all profiles Block customize block for gauge
Silicon slag is a grayblack granular solid waste produced by partial oxidation and partial reduction of silicon materials at high temperatures Silicon slag mainly comes from silicon material processing processes in the metallurgy and semiconductor industries such as silicon wafer slicing ferrosilicon smelting and other processes The main components of silicon slag are SiO2 and a small amount of FeO Al2O3 CaO and other elements and oxides 1 Make cement Silica slag can be used as an additive in cement clinker to replace some materials such as plaster of paris or fly ash in cement clinker Silica slag can promote the hydration reaction of cement clinker and enhance the early strength and longterm performance of cement 2 Making glass Silica slag is an important raw material for glass manufacturing It can replace part of the raw materials such as quartz sand and sodium carbonate reduce the cost of glass production and at the same time improve the quality and weathering resistance of the glass 3 Manufacturing Ceramics After silicon slag is mixed with materials such as alumina calcium oxide and magnesium oxide highperformance refractory ceramic materials can be prepared These materials have excellent properties such as hightemperature fire resistance high strength and wear resistance and are widely used in hightemperature furnaces chemical equipment and other fields 4 Manufacturing building materials Silica slag can be used as a raw material for manufacturing building materials such as building bricks sound insulation panels and thermal insulation materials Building materials made of silicon slag have high strength wear resistance fire resistance and other properties and also have good heat and sound insulation properties 5 Other uses Silicon slag can also be used to manufacture graphite electrodes iron oxide pigments electrical insulation materials and other products In addition silica slag can also be recycled such as used to make road hardeners lowcarbon cement etc
Plasma cutting machines are used for iron/steel plate cutting, if you have big size metal to cut, the portable and table type are all not suitable. You need choose gantry type plasma cutting machines, but it price is very high. So we design this kind plasma cutting machines that can cut big size iron/steel plate with good price. Features of plasma cutting machines: 1 .The machine is all welded as seamless steel structure. Steady structure and long life time 2. High configuration, high cutting speed and precision. 3., Auto ARC starting. Steady performance. 4, Control system: STARFIRE control, with USB interface 5. Cutting material: steel, copper, iron, aluminum, galvanized sheet, titanium plates, and so on. 6. File format: G-code 7, Suitable Software: CAD, ART CUT, Type, Art CAM etc Parameters of plasma cutting machines Working Voltage 3-Phase 380V/2-phrase 220V Working Area(X*Y) 2000*3000mm, 2000*4000mm, 2000*5000mm, 2000*6000mm Machine Structure Welded X Y Guide Rail Taiwan HIWIN Square Rail X Y Transmission Imported Rack gears Drive Mode Stepper Motor (Optional Servo ) Control System STARFIRE Max thickness 30mm Plasma Generator 63A/100A /120A/160A/200A Cutting Speed 0-10000mm/min G.W. 1500KGS
RB-6000 round steel tube tube CNC plasma cutting machine is a device that automatically calculates and cuts the joints of steel tube ends. This kind of plasma cutting machine is widely used in the cutting and processing of tubes in the construction, chemical, machinery, metallurgical and other industries. In these industries, there are a large number of tube junctions, intersecting line holes, and intersecting line ends. In the past, these processes used backward and cumbersome methods such as making prototypes, scribing, manual lofting, manual cutting, and manual polishing. And this kind of plasma cutting machine can cut this kind of round tube very conveniently, and the operator does not need to calculate and manually program, only we need to input the diameter of the tube, the intersection angle and other parameters, the machine can automatically cut the graphics we want. Performance characteristics of plasma cutting machine: 1. Control System This system has three-axis linkage and supports cutting of flat and round tubes. When we use the machine to cut round tubes, we can choose the library owned by the system, and the system also supports any round tube nesting software. 2. Arc voltage height controller The machine can automatically adjust the cutting height according to the bending of the iron plate. 3. Machine support frame The base plate of the support base is made of 12mm steel plate, which is formed and processed in a CNC machining center at one time to ensure the machining accuracy and service life. The use of precise lead screw drive can bear more weight and save effort for lifting. 4. Chuck holder The drive motor adopts a servo motor, which has stable operation, high precision and long service life. 5. The transmission mode is gear plate and gear coordinated transmission, and the operation is very stable. 6. The chuck adopts 250# three-jaw chuck, which has high precision and good cutting quality.
This smokeless Hypertherm Gantry CNC Plasma Cutter is mainly used for cutting the Steel/Iron sheet automatically. It is equipped with a special plasma cutting smoke treatment device, which effectively improves the working environment of the plasma cutting machine workshop. This Gantry Plasma Cutter is widely used for steel structure, shipbuilding, bridge and heavy machine industries. Cutting material: low carbon steel, stainless steel and non-ferrous metal, etc. machine can be designed according to the different needs of users. Features of smokeless Hypertherm Gantry CNC Plasma Cutter: 1. Beam with strong structural design, the structure has good rigidity, light weight, exercise inerti. 2. Gantry-type structure, Y-axis synchronous dual-motor drive and XYZ axis with circular rail (optional formula-type linear guide), steady transmission, and high accuracy. 3. Support WENTAI, BEIHANG HAIER, ARTCAM, Type3 software such as the standard G code path generated file can also be read by software conversion software such ad AUTOCAD generated DXF formats. 4. U disk exchange control system processing files, easy to operate. 5. Plasma torch power supply and supporting all famous brands such as American Hypertherm, a number of national patents by the manufacturers. Parameters of smokeless Hypertherm Gantry CNC Plasma Cutter: Model RB3060 Power source 220V,380V/50HZ Working area 3000*6000mm Cutting mode Plasma only, flame only, plasma and flame Cutting speed 0-4000mm per minute Plasma cut thickness Depend on current of plasma power source Flame cut thickness 10-200mm Cutting length 6000-12000mm (Can be as required) Number of Control Axes 3 Height range 0-500mm Height adjuster mode Automatic(include 24DC geared motor) Driving mode Stepper or servo mode, dual driving Operation system FANGLING , STARFIRE, START, Hypertherm Language version English, Chinese Russian, Spanish, French, Japanese, Czech, Slovak File transmission USB transmission
Affordable 5*10 feet CNC plasma and gas/flame cutting machine (CNC plasma cutter) is widely used in industry of Ship Building, Construction Equipment, Transport Equipment, Aerospace Industry, Bridge Building, military industrial, wind power, Structural Steel, Boiler containers, Agriculture Machinery, Chassis electrical cabinets, Elevator manufacturers, Textile Machinery and so on. Features of Affordable 5*10 feet CNC plasma and gas/flame cutting machine (CNC plasma cutter): 1. Three torch: plasma torch , gas/flame torch, marking torch for different materials. 2. TORCH HEIGHT CONTROLLER--The numerical control system with high disposes, the automatic striking arc, the performance is stable. STARFIRE cutting system panel, Auto Initial Height Sensing, Arc Voltage Divide etc, can cut different thickness, automatic height control, easy operation, high efficiency. 3. Blade and saw working table for choose, support heavy metal with high stability. 4. High precision square rail, and rack gear. 5. HUAYUAN plasma power supply(USA HYPERTHERM for optional),excellently performance, low failure rate, more secure. 6. Stepper motor (servo for optional) cooperate with precision machinery transmission system, faster and more stable, higher cutting efficiency. Affordable 5*10 feet CNC plasma and gas/flame cutting machine (CNC plasma cutter): Working area 1300*2500mm, 1500*3000mm, 1500*6000mm (can be customized) Transmission High precision Rack Gears, Ball Screw X, Y, Z Rail Square Rail Cutting Thickness 0-30mm, plasma cutting 8-200mm,gas /flame cutting Cutting Speed 0-12000m/min Plasma Generator 63A (more optional 120A,160A ,200A) Motor Stepper motor(servo motor optional) Control system STARFIRE, FANGLING, Document transmission form USB interface Working voltage 3 phase 380V 220V 50HZ/60HZ Software CAD, FASTCAM,ARTCAM
Starting a ruminant feed pellet plant has been a profitable business endeavor in many countries. The ruminant feed pellet machine line is mechanical equipment that specializes in making ruminant feed. For example, it can produce cattle feed, dairy cow feed, beef cattle feed, sheep feed, goat feed, camel feed, alpaca feed, and so on. How to make ruminant feed? You need Ruminant feed pellet machine line equipment. Herm machinery computer controls the ruminant feed pellet machine line with an output range of 1 ton/hour to 100 ton/hour, Complete ruminant feed pellet machine line includes raw material storage, cleaning machine, crushing machine, feed mixing machine, ruminant feed pellet maker, cooling machine, screening machine, packaging systems, transportation, and electronic control system. The complete ruminant feed pellet production line uses barley, forage, pulses, bran, wheat, corn, and additives such as vitamins, minerals, and other essential trace ingredients to produce feed pellets. The granules are rich in nutrients and can meet the growing needs of ruminants at different growth stages. By combining the moisture, heat, and pressure of the feed ingredients, a degree of gelatinization is created, which allows ruminants to better utilize the nutrients in these ingredients. 2-12mm cylindrical feed pellets are available according to your needs. At the same time, the ruminant feed production plant has the characteristics of low energy consumption, high production efficiency, and large profits. It is especially suitable for large feed mills, breeding farms, large farms, etc. Another, we provide free installation, training, factory design, and timely after-sales service.
XCA107 Motor Controller for Automotive Water Pump The XCA107 motor controller is designed to raise efficiency of automotive water pump. It controls automotive water pump and turns it ON/OFF with respect to water level in the tank. Excellent compatibility with electronic control unit enables automotive water pump controller to collaborate with other systems. XCA107 automotive water pump controller can withstand long-term harsh environment such as high temperature, bumping and extreme weather conditions, achieving high reliability and durability. This product has been introducing by FAW group, Feilong Auto Components, Unicent etc. XC Motor Control Technology developed XCA107 automotive water pump controller with particular attention to quality, operational safety, ease of use and reliability. It comes with: Specification: 1. Working voltage: DC16~36V 2. Rated current: 4.6A 3. Operating temperature: -40 ~ 125â?? 4. Working humidity: 95% Max 5. Dimension: 61*56*17MM 6. Protection type: under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection 7. PWM speed regulation, FG signal feedback, FOC sine wave control 8. CSIPER 25 Certified 9. ISO11452-2 certified 10. ISO10605 certified 11. ISO16750 environmental certified 12. ISO7637 certified XC Technology has been engaging in this specialized field of motor control since 2011, serving notable customers such as FAW group, Dongfeng NISSAN, Cummins, XPeng Aero car, Unicent and more. Contact us for detail. XCA107 automotive water pump controller efficient, reliable and ease of use.
Automotive Fuel Pump Controller XCA105 Improves Performance of Fuel Pump Xiongcai automotive fuel pump controller XCA105 is engineered to improve running efficiency of automotive oil pump. This automotive fuel pump controller is designed for a large automotive fuel pump manufacturer. Engineered from ground, we provided a full service from design, analysis, testing to production. This product has been applying in top brands FAW group, Dongfeng NISSAN, Cummins, etc. XCA105 motor controller can adjust the working parameters of fuel pump according to Vehicleâ??s running conditions and engine status to ensure stable fuel supply. The automotive oil pump controller will monitor oil pump all the time, if there is an abnormality, the controller will send signals for detection, ensuring vehicle safety. XCA105 automotive fuel pump controller features: 1. Working voltage: DC8~18V 2. Rated current: 8A 3. Operating temperature: -40 ~ 125 4. Working humidity: 95% Max 5. Overall size: 37*34*8MM 6. Protection type: under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection 7. CSIPER 25 radiation and conduction level 3 certified 8. ISO11452-2 EMS level 4 BCI 100MAcertified 9. ISO10605 contact discharge 8KV and air discharge 16KV certified 10. ISO16750 environment certified This product is highly reliable and durable. To adapt extreme working environment. automotive oil pump controller adopts high temperature resistance, waterproof, dustproof and vibration-resistant designs to achieve high reliability and durability. We are an IATF16949 certified company. We proud ourselves on providing reliable, durable products for top clients like FAW Group NISSAN, XPeng Aero car, Cummins and more Have a try, with expertise in this specialized field, Xiongcai Motor Control Technology Co., Ltd is able to take your technological aspirations to a new level.
ARSPL UPVC ROOF SHEET 1) Heat insulation up to 40%. Excellent Thermal Insulation: Thermal Conductivity 0.104 W/m* C 2) Excellent sound insulating properties 3) Resistance to acids, alkalis, salts and solvents, corrosion 4) Resistance to the extreme weather conditions: snow, hail, high wind â??pressure 5) High Strength Characteristic: Tensile Strength 29~31 MPa, Flexural ` strength 45~55MPa, Impact Resistance 50~60kJ/m2 6) Temperature usage Range: from -40 C to +75 C. Material `withstands over 100 cycles of freezing and thawing 7) Color Fastness: Pigments used are 8 points on the BW Scale 8) Light Weight: 3.6Kg/m2 9) Resistance to the influence of ultraviolet rays. Highly UV protected. 10) Non-combustible nature of the material. Class B1 Retardant Building Materials. Fire Retardant. 11) Easiness of installation: material can be easily cut, drilled, and sawn 12) Absolute waterproof properties 13) Flexibility: material allows roofing of hanger-type structures and spherical fencing 14) Economical Installation: overlapping waste doesnâ??t exceed 8%. High utilization efficiency up to 95% 15) Availability of the same profile transparent sheets for the creation of sky-- lights. 16) Wide Variety of available colors. Good aesthetic appeal. 17) Cost-effective in installation and saves construction costs up to 70%. 18) Eco-friendly & Energy Efficient Green product. 19) Non-Carcinogenic 20) Increases labor productivity and machinery efficiency 21) Non-conductor of electricity. 22) Long life 23) Compulsory for some industries like chemical, pharma, fertilizer, leather, process, etc.
In the north, the temperature in winter can be as low as ten degrees below zero, and in some provinces it can be as low as thirty or forty degrees below zero. It can be said that a drop of water turns into ice. At this time, if our slurry pump is installed outdoors, it will easily freeze or even crack. So how should we antifreeze our slurry pump in winter? Today, Shijiazhuang Pansto Pump Industry will introduce some small methods to prevent freezing in winter. I hope it will be helpful to everyone. 1. Add insulation materials to the slurry pump, such as cotton wool, clothing, etc., and wrap these insulation materials around the pump body to prevent the slurry pump from freezing. 2. Empty the slurry in the slurry pump that is not in use temporarily. Add water before use to prevent slurry in the pump cavity, which may cause the pump body to freeze and crack. 3. Close the doors and windows of the pump room tightly, and attach sealing strips if necessary to ensure the temperature of the pump room. 4. If we find that the slurry pump has frozen, we must not start the water pump. We can use hot water to slowly pour into the pump cavity to melt the ice, or heat the casing of the slurry pump. If you want to know more about slurry pumps, please feel free to call us! Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-55AS Units: Automatic Feeder+Automatic55Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker & Auto Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm ~0.250mm; Alloy: 8011, 8006, 3003, 3005; Temper O to H24; 2. Good Japan's Inverter, PLC and 10inch Touch Screen control system; 3. Max. Width of Aluminum foil: 600mm; 4. Max. Diameter of Aluminum foil: 700mm; 5. Core diameter of Aluminum foil: 76mm(152mm as Optional ); 6. Working speed: 40-75 times/min; 7. Total Power: 13kw; 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 6100*2600*3200mm; Technical Data: Max. Mould Size:L700*800*420mm; Slide block stroke: 120-200mm (Standard: 180mm); Automatic mould adjust unit: 0.5kw; Work plate dimension: 700*950mm; Mould handle hole dimension: 50*60mm(Diameter*Depth); Power: 3P, 380/220V, 50/60Hz; Net weight: 6000kg. SEAC-55AS is two cavities capacity for Aluminum foil container production now, it have instead of the old 40Ton model, as it is more big capacity to cover container size! Complete automatic level upgrade your factory capacity, lead your company be higher level competition and situation.
Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-63A-4 : Max. Mould Lenght 1150mm Units: Automatic Feeder+Automatic 63Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker& Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm~0.250mm; Alloy: 8011, 8006, 3003, 3005 etc.; 2. Japan Inverter, PLC and 10inch touch screen control system; 3. Max. Width of Aluminum foil: 880mm; 4. Max. Diameter of Aluminum foil: 1000mm; 5. Core diameter of Aluminum foil: 76/152mm; 6. Working speed: 40-75 times/min; 7. Total Power: 11kw+2kw+2kw+1kw; 4Motor 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 7100*2600*3500mm; Technical Data: Max. Mould Size: 1100*900*450mm; Slide block stroke: 180-260mm; Slide block dimension: 380*145mm; Automatic mould height adjust unit: 0.5kw; Work plate dimension: 1100*200*300mm, separated two sets with Balls; Tension: complete automatic adjust; Feeding System: Servo Motor, higher precision and more power; Auto Stacker: SMC lift for stacking system, top quality; Power: 4P, 380V or 220V, 50Hz /60Hz; Net weight: 9,500kg.
Product Description Railway switch rail for railway measurement & maintenance The switch rail lateral wear gauge is used to measure the switch rail lateral wear and descent height value of the switch rail, it can be used for all the type of switch rail. BENEFITS Switch Rail Lateral Wear Gauge has the advantages of high measuring accuracy, easy to operate,high reliability,small volume,light weight etc. Specification Material alumunium Dimensions (L x W x H) (mm) 800*20*50mm Place of Origin China Brand Name Linkage Product name Digital switch rail wear gauge Model LJ-JGCM-I Vertical wear measure range 92-193mm Lateral wear measure range 0-120mm Resolution 0.01mm Indication error -0.15~0.15mm Quality Control iso Standard crcc Warranty 1YEAR Certificate CE Package & Delivery Aluminum box + pe bag+pe foam+paper carton, 1 units/carton , carton size:36*25*12mm G.W: 4KG Company Profile Wuhan Linkage track Co., Ltd. established in 2022, we are a rapidly growing company involved in the design and manufacture of an extensive range of equipment for the railway industry. We started our business from producing railway measurement device in 2003 and wide our product range to small rail machines like rail cutting machine ,rail grinding etc . Our company has expanded its operation to include three branch office , location facilitates in Xiangyang ,Wuhan and Guangzhou China. Now, Linkage family of brands provides a diverse and comprehensive product line for different markets and demands. Our products are sold in more than 50 countries and regions worldwide. Market acceptance is backed by ISO9001, European CE certification . As a Chinese mainland based company, we like to take our advantage of low cost and strive to offer you quality products with most competitive pricing with integrity.
Technical Parameters Travel of X and Y Axes: 800x1200 mm; Maximum cutting thickness/ Maximum height of the part: 700 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 985x1580 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 160 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150 �¼s; Approx. Machine size (LxWxH): 2600x2400x1800 mm; Approx. Machine weight: 4500 kg; Approx. Machine control cabinet size: 670x630x1800 mm; Approx. Machine control cabinet weight: 200 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 â??. ;
Technical Parameters : Travel of X and Y Axes: 500x630 mm; Maximum cutting thickness/ Maximum height of the part: 600 mm; Maximum Work piece weight: 700 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 600x860x600 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 150 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150; Approx. Machine size (LxWxH): 2000x1950x1750 mm; Approx. Machine weight: 2540 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 ;
Very Profitable Aluminum Foil Container Production Line Complete Automatic Aluminium Foil Container Making Machine Model: SEAC-80/130AS (Four Cavities or Five Cavities Capacity !) Units: Automatic Feeder+Automatic 80Ton H Type Press+Cavities Mould+Auto Stacker+Scrap Sucker & Auto Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1.Raw material: Aluminum foil; Thickness: 0.030mm ~0.280mm; Alloy: 8011,8006,3003,3005; Temper O to H24; 2.Good Japan's Inverter, PLC and 10inch Touch Screen control system; 3.Max. width of Aluminum foil: 1220mm; 4.Max. diameter of Aluminum foil: 1000mm; 5.Core diameter of Aluminum foil: 76mm(152mm as Optional ); 6.Working speed: 40-75 times/min; 7.Total Power: 14kw+2kw+2.5kw+3kw; 8.Compressed air needed: 0.5- 0.8 Mpa, 0.4m3/min; 9.Install dimension: 7100*2600*3600mm; Technical Data: Max.mould size: 1480*1000*500mm; Slide block stroke:150-260mm ; (Offer Stroke adjustable system as option!) Automatic mould adjust unit: 0.5kw; Work plate dimension: 1500*1000mm; Mould handle hole dimension: 80*80mm(Diameter*Depth); Power: 4P, 380/220V, 50/60Hz; Net weight: 13,000kg. SEAC-80AS is the four cavities or five cavities capacity model production line for AFC. Complete automatic level upgrade your factory capacity, lead your company be higher level competition and situation.
Sudanese Senna, Cassia acutifolia, Del C. Senna L is a perennial 1-2 m height undershrub. The stem is erect, smooth, and pale green to light brown with long spreading ascending branches. Leaves are compound with four to six pairs of leaflets. The full grown leaflets are bluish-green to pale- green in color and emit a characteristic fetid smell when crushed. The flowers are small and yellow and axillary arranged racemes. The pods are broadly oblong about 5-8 cm long and 2-3 cm broad, green in beginning and change to greenish-brown to dark brown on maturity. Each pod has 5 to 7 ovate, compressed, smooth, dark-brown seeds. The two most widely exported and officially recognized species of seena are C. acutifolia and C. angustifolia. Cassia senna; used as medicine, cosmetics, health hygiene and food supplements in improving the quality of life Both Pods & leaves are used as natural laxative to treat constipation. They act on the large intestine to stimulate peristalsis (the muscular activity of the colon leading to elimination). It is known that several countries utilize the leaves of different indigenously available species for the same purpose. Senna also used as an expectorant, a wound dressing, an anti-dysenteric, and a carminative agent. It is useful in the treatment of gonorrhea, skin diseases, dyspepsia, fevers and hemorrhoids. The herb is used in the form of crude plant material or powder as oral infusion or extracts (liquid or solid). It is always advised to use the drug under the supervision of Physician, because the excess use of senna may have adverse effect leading to sudden and intense stomach pains and colic or abdominal pains.
UTERS Interchange hydraulic Lubrication Oil Filter Elements are designed for use in filters that have been designed to operate in industrial and mobile hydraulic systems. They will protect hydraulic components from particulate contamination. Filter Element Features: Material: Fiber Glass;Oil Paper;SS Mesh Filtration efficiency: 99.9% Filter rating: 1-100 um Operating Pressure: 1.0Mpa, 2.0Mpa, 16.0Mpa, 210Mpa Application field: Lubricating oil & hydraulic oil system O-Ring: NBR, fluoro rubber Filter Element Application: The hydraulic oil filter element is an indispensable part of the pipeline series of the conveying medium. It is usually installed in the inlet filter of the hydraulic system to filter out metal particles and contaminants in the fluid medium and to protect the normal operation of machinery and equipment. The application range of hydraulic oil filter elements is very wide, covering almost all industries: steel, electric power, metallurgy, shipbuilding, aviation, paper making, chemical industry, machine tools and construction machinery, construction machinery and other fields. Quality Standard: ISO 2941------Collapse & Burst Resistant ISO 2942------Fabrication & Integrity Test ISO 2943------Material Compatibility with Fluids ISO 3724------Flow Fatigue Characteristics ISO 3968------Pressure Drop vs. Flow Rate ISO 16889------Multi-pass Performance Testing Package & Shipment Package: Plastic bag inside,Paper box outside.Usually we pack filter element by paper boxes.and use export standard wooden boxes or pallets for heavy goods. Shipment: Express For Small Package,and also could offer Express lines service for Southeast Asian countries, Central Asian countries,Middle East countries; Air Shipment could ship goods above 45 kgs with faster time; Sea Shipment could ship goods with big volume or heavy total weight,with longer time; China-Europe freight train could ship goods to the countries and regions along the route, the destination is in Europe.and could offer door to door service!
UTERS Interchange hydraulic Lubrication Oil Filter Elements are designed for use in filters that have been designed to operate in industrial and mobile hydraulic systems. They will protect hydraulic components from particulate contamination. Filter Element Features: Material: Fiber Glass;Oil Paper;SS Mesh Filtration efficiency: 99.9% Filter rating: 1-100 um Operating Pressure: 1.0Mpa, 2.0Mpa, 16.0Mpa, 210Mpa Application field: Lubricating oil & hydraulic oil system O-Ring: NBR, fluoro rubber Filter Element Application: The hydraulic oil filter element is an indispensable part of the pipeline series of the conveying medium. It is usually installed in the inlet filter of the hydraulic system to filter out metal particles and contaminants in the fluid medium and to protect the normal operation of machinery and equipment. The application range of hydraulic oil filter elements is very wide, covering almost all industries: steel, electric power, metallurgy, shipbuilding, aviation, paper making, chemical industry, machine tools and construction machinery, construction machinery and other fields. Quality Standard: ISO 2941------Collapse & Burst Resistant ISO 2942------Fabrication & Integrity Test ISO 2943------Material Compatibility with Fluids ISO 3724------Flow Fatigue Characteristics ISO 3968------Pressure Drop vs. Flow Rate ISO 16889------Multi-pass Performance Testing Package & Shipment Package: Plastic bag inside,Paper box outside.Usually we pack filter element by paper boxes.and use export standard wooden boxes or pallets for heavy goods. Shipment: Express For Small Package,and also could offer Express lines service for Southeast Asian countries, Central Asian countries,Middle East countries; Air Shipment could ship goods above 45 kgs with faster time; Sea Shipment could ship goods with big volume or heavy total weight,with longer time; China-Europe freight train could ship goods to the countries and regions along the route, the destination is in Europe.and could offer door to door service!