MS5534C Barometer Module SPECIFICATIONS * 10 - 1100 mbar absolute pressure range * 6 coefficients for software compensation stored on-chip * Piezoresistive silicon micromachined sensor * Integrated miniature pressure sensor 9 x 9 mm * 16 Bit ADC * 3-wire serial interface * 1 system clock line (32.768 kHz) * Low voltage and low power consumption Description: The MS5534C is a SMD-hybrid device including a piezoresistive pressure sensor and an ADC-Interface IC. It provides a 16-bit data word from a pressure and temperature dependent voltage. Additionally the module contains 6 readable coefficients for a highly accurate software calibration of the sensor. MS5534C is a low power, low voltage device with automatic power down (ON/OFF) switching. A 3-wire interface is used for all communications with a microcontroller. The MS5534C is fully software compatible to the previous versions (MS5534A and MS5534B). Compared to the previous versions, the ESD sensitivity level has been improved to 4kV on all pins. Features: * Supply voltage 2.2 V to 3.6 V * Low supply current * -40'C to +125'C operation temperature * No external components required Applications: * Mobile altimeter/barometer systems * Weather control systems * Adventure or multi-mode watches * GPS receivers
Incoloy Alloy 908 is a high-temperature, high-strength, and highly corrosion-resistant alloy composed of elements such as nickel, chromium, molybdenum, and iron. It is a single-phase austenitic alloy, typically formed by casting and forging. Chemical composition: The chemical composition of Incoloy Alloy 908 is composed of elements such as nickel, chromium, iron, molybdenum, vanadium, manganese, tantalum, silicon, carbon, phosphorus, and sulfur. Nickel content is 40-45%, chromium content is 20-23%, iron content is 16-19%, and molybdenum content is 8-10%. Mechanical properties: Incoloy Alloy 908 has excellent high-temperature and high-strength performance. Its tensile strength is 135 ksi (930 MPa) (minimum), yield strength is 70 ksi (480 MPa) (minimum), and elongation is 25% (minimum). Physical properties: The density of Incoloy Alloy 908 is 8.14 g/cm�³, the melting point is 1338�°C (2440�°F), the thermal conductivity is 11.7 W/m�·K (100�°C), and the coefficient of thermal expansion is 13.7 �¼m/m-K (20-100�°C). Corrosion resistance: Incoloy Alloy 908 has excellent corrosion resistance, especially in high-temperature, high-pressure, and highly corrosive environments. It can withstand the corrosion of corrosive media such as sulfuric acid, hydrochloric acid, nitric acid, and fluoride, and can resist chloride stress corrosion cracking (SCC). The international standard designations for Incoloy alloy 908 include UNS N09908 and W.Nr. 1.4876. There are also corresponding standards and specifications in different countries and regions, such as AMS and ASTM standards in the United States, EN standards in Europe, and JIS and JPI standards in Japan. Here are the specific standards and designations for Incoloy alloy 908 in different countries: United States: AMS 5545, AMS 5546, AMS 5547, AMS 5549, ASTM B408, UNS N09908 Germany: DIN 17752, DIN 17753, DIN 17754, W.Nr. 1.4876 United Kingdom: BS HR 6 Europe: EN 10095 Japan: JIS H4551, JPI-SB46 We can provide the following the form:Incoloy alloy908 coil; Incoloy alloy908 strip;Incoloy alloy908 plate; Incoloy alloy908 sheets; Incoloy alloy908 tube; Incoloy alloy908 pipe;Incoloy alloy908 flat; Incoloy alloy908 bar GB:HR 6/JIS:H4551/UNS:N09908/W.Nr:1.4876
Silicon wafer for solar panel.
The fuel rail sensor, commonly referred to as the Fuel Pressure Sensor. High-pressure diesel component 0281006164 is mounted at one end of the fuel rail to measure fuel pressure in the common pipe.The sensor sends this signal to the ECU, which then uses it to make adjustments to the vehicle s fuel and timing. When the sensor has an issue it can cause problems with the performance of the vehicle. Quality Guarantee :1 year, and strictly in accordance with the standard quality inspection The products are 100% new and carefully packed. 1.Name: Fuel Pressure sensor,Fuel high Pressure sensor 2.Certification: CE, TS16949 3.Model NO.: 0281006164 4.Function: Control emissions in combustion environments 5.Application: ALFA ROMEO CHRYSLER FIAT FORD GMC IVECO JEEP LANCIA OPEL SUZUKI FEBI 6.Ciondition: 100% NEW 7.Weight(g): 50.7g 8.Deliverytime: 7-15 days 9.Packing: Neutral packing Customize according to customer needs
Order our Fuel Pressure Sensor and we offer a 12 month warranty for a truly worry-free shopping experience. If you want to know about Nitrogen Oxide (Nox) Sensors,fuel metering unit, and other products, please feel free to contact us. Quality Guarantee :1 year, and strictly in accordance with the standard quality inspection The products are 100% new and carefully packed. 1.Name: Fuel Pressure sensor,Fuel high Pressure sensor 2.Certification: CE, TS16949 3.Model NO.: 46812910 4.Function: Control emissions in combustion environments 5.Application: FIAT IVECO ALFA ROMEO 6.Ciondition: 100% NEW 7.Weight(g): 50.7g 8.Deliverytime: 7-15 days 9.Packing: Neutral packing Customize according to customer needs
Silicon raw material.
Quick Details Place of Origin: Sichuan, China (Mainland) Brand Name: SAND Model Number: PT3xx6 Series Pressure Range: 0~150MPa (20000psi) Accuracy: ±1.0% FS Power: 10V DC (6~12V DC) Signal Output: 3.33mV/V (Full 33.3mV) or 3.0mV/V (Full 30mV) Probe Temperature: 535 PT3XX6 Series:PT3116 Series, PT3216 Series, PT3226 Series. Mercury Free Ultra-Temperature Melt Pressure Transducer (Sensor) Product Introduction: PT3xx6 Series Melt Pressure Transducer(Melt Pressure Sensor). This series are used a special material and pressure transmission which can bear as high as 535 °C measuring medium to replace the traditional 400 °C. this technology is created by our company only in home. Performance Parameters: Pressure Range: 0 ~ 5 MPA~ 150 MPA ( 0 ~ 750psi ~ 20000psi ); Accuracy: ±0.5% FS; Power: 10VDC ( 6 ~ 12 V DC ); Output Signal: 3.33mV/V (Default), 3.0mV/V(Optional) etc. Probe Heat Resistance: PT4516 Series: 300°C; PT4616 and PT4626 Series: 400°C; Temperature Drift: =500M/500VDC; Mechanical Connections: 1/2"-20UNF, M10x1.5, M12x1.5, M14x1.5, M18x1.5, M22x1.5 etc. (Optional) Electrical Connections: 6PIN (SD02106P/SD02106S); Thermometric Config: Thermocouple: E, J, K, S type etc.; (PT4626 Series Optional); Thermal Resistance: Pt100 etc. (PT4626 Series Optional); Features: * Anticorrosive wear-resisting coating: apply to high concentrations of rough media pressure measurement, can improve the service life of 3 to 5 times (optional); * Special requirement can make to order, delivery date 7 ~ 15 working days; * Optional supporting intelligent digital pressure meter: PS1016-43x series, PS4810-43x series, PS4812-43x series and PS9016-43x series. Order Format: Example1: PT3816-350bar-M18-150/470-3.33mV/V Note: Product design Model "PT3816". Function code "Null" stands for melt pressure transducer. Coating code "Null" stands for without coating . Pressure range: 0 ~ 350bar.
Quick Details Place of Origin: Sichuan, China (Mainland) Brand Name: SAND Model Number: PT3xx6 Series Pressure Range: 0~150MPa (20000psi) Accuracy: ±1.0% FS Power: 10V DC (6~12V DC) Signal Output: 3.33mV/V (Full 33.3mV) or 3.0mV/V (Full 30mV) Probe Temperature: 535 Temperature Drift:
Digital Output Barometer Sensors Enhanced Digital Output Sensors: Extended temperature range ADO Series Barometric Military Grade Pressure Sensors General Description The Digital Output pressure sensors are based upon a proprietary surface mapping technology to produce a fully digital output that virtually eliminates all repeatable errors over temperature and pressure. This series provides a 12 bit digital serial output (14 bit in High Resolution Mode) with superior offset, span and linearity characteristics. The output is SPI and MICROWIRE/PLUS® compatible as well as fully compatible with the All Sensors GA142 Series sensors. In addition to synchronous communications, the Digital Output pressure sensors incorporates a bi-directional, TTL level, asynchronous serial interfaces mode (hardware selectable 9,600 or 19,200 baud). This mode includes a command set that allows the host to interrogate the sensor for model information, pressure range, serial number, pressure units and conversion factor. The command set also allows the host to select a high resolution output mode, make minor adjustments to offset and has an addressable feature that alows multiple sensors to be tied to the same interface buss. This series is intended for use with non-corrosive, non-ionic working fluids such as air, dry gases and the like. All signals are 5V TTL/CMOS compatible. ADO Series Barometric Military Grade Pressure Sensors Features * All Combined Errors Over Temperature Less Than 0.1%, Typical * Wide -40 to 125°C Compensated Temperature Range *Electrically Compatible to All Sensors GA142 Series * Enhanced Dual Serial Interface Mode ADO Series Barometric Military Grade Pressure Sensors Applications * Medical Instrumentation * Environmental Controls * Meteorology ADO Series Barometric Military Grade Digital Output Pressure Sensors * Operating Pressure: 600 to 1100 mBar * Proof Pressure: 60 PSI * Burst Pressure: 120 PSI * Supply Voltage: 7Vdc * Compensated Temperature: -40°C to +125° C * Operating Temperature: -40 to +125° C * Humidity Limits: 0 to 95% RH (non condensing)
BLCR Series Low Voltage Pressure Sensors General Description The BLCR Series Basic Sensor is based on a Dual Die Reference technology to reduce all output offset or common mode errors. It also incorporates All Sensors' CoBeam Technology to reduce overall supply voltage while maintaining comparable output levels to traditional equivalent basic sensing elements. This lower supply voltage gives rise to improved warm-up shift whilte the CoBeam technology itself reduces package stress susceptibility resulting in improved overall long term stability. The technology also vastly improves position sensitivity to nearly unmeasurable levels. This series is intended for use with non-corrosive, non-ionic working fluids such as air, dry gases and the like. The output is also ratiometric to the supply voltage and is operable from 1.8 to 3.3 volts DC. BLCR Series Low Voltage Pressure Sensors Features * 0 to 1 inH2O to 0 to 30 inH2O Pressure Ranges * Low Supply Voltage (1.8V to 3.3V) * 0.1% Linearity Typical * Improved Front to Back Linearity * Intrinsically No Position Sensitivity * Improved Warm-Up Shift Distribution * Parylene Coating Available Upon Request * Reduced TCO BLCR Series Low Voltage Pressure Sensors Applications * Medical Instrumentation * Environmental Controls * HVAC Performance Characteristics for BLCR Series Low Voltage Pressure Sensors * 0 to 1 inH2O to 0 to 30 inH2O Pressure Ranges * Supply Voltage: 5 Vdc * Common Mode Pressure: 5 psig * Lead Temperature (soldering 2-4 sec.): 270 C * Operating Temperature:-25 to 85 C * Storage Temperature: -40 to 125 C * Hum idity Limits: 0 to 95% RH (non condensing)
FOP-C Fiber Optic Pressure Sensor Description The FOP-C is a fiber optic pressure sensor designed for general industrial applications in harsh and hazardous environments, where very high pressure conditions can be found. FOP-C Fiber Optic Pressure Sensor Key features: * Intrinsically safe * Immune to EMI/RFI * From 30 to 10,000psi range * Accuracy of 0.25% * Lead cable: up to 3km FOP-C Fiber Optic Pressure Sensor Applications: * Industrial environments * In-situ process monitoring * Harsh and hazardous environments * High pressure environments * Aerospace applications * Oil well and natural gas pumping station * Plastic injection molding and extrusion monitoring * Food packaging FOP-C Fiber Optic Pressure Sensor Specifications: Pressure range: from 30psi to 10,000psi (170 to 69,000kPa) Resolution: 0.00625% typical with averaging Accuracy: 0.25% of full scale Connector type: ST connector (optional connector for long range applications) Operating temperature: -20 to 60'C (-4 to 140'F)
FOP-MA Acoustic Fiber Optic Pressure Sensor The FOP-MA is a fiber optic pressure sensor designed for use in acoustics or microphone applications or whenever a very sensitive pressure sensor is needed. It features high frequency response and a high sensitivity to detect slight pressure variations under the most adverse conditions. The FOP-MA acoustic pressure sensor offers small size, high accuracy, immunity to EMI/RFI, and resistance to corrosive environments. FOP-MA Acoustic Fiber Optic Pressure Sensor Key Features: * Miniature size * All-optic * Immune to EMI/RFI * High resolution * Frequency response up to 30 kHz FOP-MA Acoustic Fiber Optic Pressure Sensor Applications: * Acoustics * Microphone * Automotive * Aerospace * Aerodynamics FOP-MA Acoustic Fiber Optic Pressure Sensor Specifications Pressure range: 0 - 2 psi Resolution(*1): 0.0075 psi Accuracy(*2): ±1% of full scale Frequency response(*3): Up to 30 kHz Connector type: ST connector Operating temperature: -20'C to 150'C (-4'F to 302'F) *1. Signal conditioner dependent. *2. Relative to atmospheric pressure. *3. Maximum achieved with a Veloce 50 signal conditioner.
SPD005GAsmd 5 psi Gauge Pressure Sensor with Analogue Output Description This pressure sensor has an amplified analogue output. The sensor is compensated for offset, sensitivity, temperature drift and nonlinearity. The sensor is available in the range from 5 to 100 psi. Other ranges on request. Available in Gauge and Absolute type. The output is ratiometric to the power supply voltage. @ 5 V power voltage the output span is 0.5 to 4.5 V. The SPD analogue series can be considered as an analogue successor of the SPD series. SPD005GAsmd 5 psi Gauge Pressure Sensor with Analogue Output Electrical Characteristics Performance Characteristic at Vcc =5V excitation @ 25C. * Supply Voltage: 4.75~5.5V * Supply Current: Max. 3mA *Pressure range: 0~5psi * Accuracy: ±1.8%FS * Operating temperature: -20~85C * Storage temperature: -40~125C
Fiber optic pressure sensor fop-miv description The fop-miv has been especially designed and tested to fulfill the highest of medical performance requirements. Its applications range from human body fluid pressure measurements, for intervention in hospital critical care units, to animal testing in high emi environments. It is available off the shelf for standard applications or it can be customized to suit oem-specific applications Fiber optic pressure sensor fop-miv features: Em/rf/mw interference complete immunity Miniature and rugged sensor for pressure measurements High performance and reliability High accuracy and repeatability Very low drift and thermal shift Fast response time Sterilizable Fiber optic pressure sensor fop-miv applications: Custom design for embedmentin diagnostic or therapeutic medical devices, automated manufacturing, high volume, low cost available sensors, computerized product testing in assembly line Cardiology, neurology, anaesthesiology, pneumonology, gastroenterology, urology, gynecology, ophthalmology, electrosurgery, thermal therapy, preclinical studies, mri and other rfi environments Medical: Fiber optic pressure sensor fop-miv oem products: Custom design for embedmentin diagnostic or therapeutic medical devices, automated manufacturing, high volume, low cost available sensors, computerized product testing in assembly line
Fop-mh high-temperature pressure sensor fiber optic pressure sensor description The fop-mh is a fiber optic pressure sensor designed mainly for applications where extreme temperature conditions can be found such as aerospace and defense. It is also a useful tool for general industrial applications in harsh and hazardous environments. Fiber optic pressure sensor fop-mh key features: Designed to operate in extreme temperature conditions, where standard sensors fail Operating temperature up to 450'c (842'f) Intrinsically safe Immune to emi/rfi Fiber optic pressure sensor fop-mh applications: Aerospace Defense Metallurgy Industrial in-situ process monitoring High temperature steam Harsh and hazardous environments High temperature environments Oil well and natural gas pumping station Plastic injection molding and extrusion monitoring Food packaging Fiber optic pressure sensor fop-mh specifications: Pressure range: 0-150 psi, 0-1000psi, 0-3000psi, 10-50psi Resolution: 0.1% of full scale Accuracy: â±1% of full scale Connector type: st connector Operating temperature: -20'c to 450'c (-4'f to 842'f)
Fiber Optic Pressure Sensor FOP-M description The FOP-M is a fiber optic pressure sensor designed mainly for applications where high temperature conditions can be found such as in aerospace and defense.It is also a useful tool for general industrial applications in harsh and hazardous environments Fiber Optic Pressure Sensor FOP-M Specification: Pressure range: 0-5, 0-50, 0-150 and 0-1,000psi Resolution:
Semi conductor transistors, diode, thyristor, solid state relay, mosfet, integrated circuit, semiconductor equipments, semiconductor parts;, schottky diode, zener diode, swiching transistor, small signal transistor, mosfet, darlington diode, semiconductor wafer, semiconductor die, semiconductor chip.
Product Categories: Monitor accessories Place of Origin: Henan, China (Mainland) Brand Name: Edan Connectors: 7 pin Model Number: J401-D(72CL-F) Type: Infant/Pediatric Silicone Soft Tip Cable Material: Medical TPU Cable Color: Gray Cable Length: 3Meter Usage: Pressure Sensor, Direct spo2 sensor connected to the monitor, no need for extension cable. Compatible Mode: H100B(Non-Oximax) Certificate: CE, ISO13485 Warranty: 12 months
Lightweight silicone thermal pad for ev battery / two part thermal gap filler grease / thermal gap pad / thermal conductive insulator / silicone putty pad / silicone thermal tape / thermally phase change material.
Nominal Scale: 35KPa ,100KPa, 250KPa, 600KPa, 1MPa, 1.6MPa, 2.5MPa, 4MPa, 6MPa, 10MPa, 16MPa, 25MPa, 40MPa, 60MPa Overload Capacity: 2 times £íº35KPa íºC 2.5MPa£© 1.5 times (4MPa íºC 60MPa) Accuracy: ¡À0.1%F.S., ¡À0.25%F.S., ¡À0.5%F.S. Power Supply: 1mADC or 5VDC(Optional) Long Term Stability: ¡À0.2%F.S./ Y Operating temperature: -30¡æ ¡« 100¡æ Insulation resistance: £¾100M¦¸(100VDC)